Biodiesel production by esterification of oleic acid with short-chain alcohols under ultrasonic irradiation condition

Production of fatty acid ethyl ester (FAEE) from oleic acid (FFA) with short-chain alcohols (ethanol, propanol, and butanol) under ultrasonic irradiation was investigated in this work. Batch esterification of oleic acid was carried out to study the effect of: test temperatures of 10–60 °C, molar ratios of alcohol to oleic acid of 1:1–10:1, quantity of catalysts of 0.5–10% (wt of sulfuric acid/wt of oleic acid) and irradiation times of 10 h. The optimum condition for the esterification process was molar ratio of alcohol to oleic acid at 3:1 with 5 wt% of H₂SO₄ at 60 °C with an irradiation time of 2 h.     

Effects of water on the esterification of free fatty acids by acid catalysts

To maximize the production of biodiesel from soybean soapstock, the effects of water on the esterification of high-FFA (free fatty acid) oils were investigated. Oleic acid and high acid acid oil (HAAO) were esterified by reaction with methanol in the presence of Amberlyst-15 as a heterogeneous catalyst or sulfuric acid as a homogeneous catalyst. The yield of fatty acid methyl ester (FAME) was studied at oil to methanol molar ratios of 1:3 and 1:6 and reaction temperatures of 60 and 80 °C. The rate of esterification of oleic acid significantly decreased as the initial water content increased to 20% of the oil. The activity of Amberlyst-15 decreased more rapidly than that of sulfuric acid, due to the direct poisoning of acid sites by water. Esterification using sulfuric acid was not affected by water until there was a 5% water addition at a 1:6 molar ratio of oil to methanol. FAME content of HAAO prepared from soapstock rapidly increased for the first 30 min of esterification. Following the 30-min mark, the rate of FAME production decreased significantly due to the accumulation of water. When methanol and Amberlyst-15 were removed from the HAAO after 30 min of esterification and fresh methanol and a catalyst were added, the time required to reach 85% FAME content was reduced from 6 h to 1.8 h.     

Application of response surface methodology for optimizing transesterification of Moringa oleifera oil: Biodiesel production

Response surface methodology (RSM), with central composite rotatable design (CCRD), was used to explore optimum conditions for the transesterification of Moringa oleifera oil. Effects of four variables, reaction temperature (25–65 °C), reaction time (20–90 min), methanol/oil molar ratio (3:1–12:1) and catalyst concentration (0.25–1.25 wt.% KOH) were appraised. The quadratic term of methanol/oil molar ratio, catalyst concentration and reaction time while the interaction terms of methanol/oil molar ratio with reaction temperature and catalyst concentration, reaction time with catalyst concentration exhibited significant effects on the yield of Moringa oil methyl esters (MOMEs)/biodiesel, p < 0.0001 and p < 0.05, respectively. Transesterification under the optimum conditions ascertained presently by RSM: 6.4:1 methanol/oil molar ratio, 0.80% catalyst concentration, 55 °C reaction temperature and 71.08 min reaction time offered 94.30% MOMEs yield. The observed and predicted values of MOMEs yield showed a linear relationship. GLC analysis of MOMEs revealed oleic acid methyl ester, with contribution of 73.22%, as the principal component. Other methyl esters detected were of palmitic, stearic, behenic and arachidic acids. Thermal stability of MOMEs produced was evaluated by thermogravimetric curve. The fuel properties such as density, kinematic viscosity, lubricity, oxidative stability, higher heating value, cetane number and cloud point etc., of MOMEs were found to be within the ASTM D6751 and EN 14214 biodiesel standards.     

Biodiesel production by esterification of palm fatty acid distillate

Production of fatty acid methyl ester (FAME) from palm fatty acid distillate (PFAD) having high free fatty acids (FFA) was investigated in this work. Batch esterifications of PFAD were carried out to study the influence of: including reaction temperatures of 70–100 °C, molar ratios of methanol to PFAD of 0.4:1–12:1, quantity of catalysts of 0–5.502% (wt of sulfuric acid/wt of PFAD) and reaction times of 15–240 min. The optimum condition for the continuous esterification process (CSTR) was molar ratio of methanol to PFAD at 8:1 with 1.834 wt% of H₂SO₄ at 70 °C under its own pressure with a retention time of 60 min. The amount of FFA was reduced from 93 wt% to less than 2 wt% at the end of the esterification process. The FAME was purified by neutralization with 3 M sodium hydroxide in water solution at a reaction temperature of 80 °C for 15 min followed by transesterification process with 0.396 M sodium hydroxide in methanol solution at a reaction temperature of 65 °C for 15 min. The final FAME product met with the Thai biodiesel quality standard, and ASTM D6751-02.     

Esterification of high FFA tung oil with solid acid catalyst in fixed bed reactor

The effect of molar ratio of methanol to oil, temperature and space velocity (SV) on pre-esterification of Tung oil was carried out in pilot-scale fixed bed reactor, with solid acid catalysts. The molar ratio results showed the maximum acid value reduction efficiency (90.21%) was obtained at the molar ratio of 8:1, the acid value decreased sharply to 0.70 g kg^?1 of KOH. And esterification reaction attained balance when space velocity was enough, so 0.029 h^?1 was optimal space velocity. Furthermore, activity of reactant and rate of reaction increase with temperature increased, and the maximum conversion was achieved at 65 °C, the acid value of Tung oil could be reduced to 1.4 g kg^?1 of KOH.     

Transport phenomena and performance of a plate methanol steam micro-reformer with serpentine flow field design

A numerical investigation of the transport phenomena and performance of a plate methanol steam micro-reformer with serpentine flow field as a function of wall temperature, fuel ratio and Reynolds number are presented. The fuel Reynolds number and H₂O/CH₃OH molar ratio (S/C) that influence the transport phenomena and methanol conversion are explored in detail. In addition, the effects of various wall temperatures on the plates that heat the channel are also investigated. The predictions show that conduction through the wall plays a significant effect on the temperature distribution and must be considered in the modeling. The predictions also indicate that a higher wall temperature enhances the chemical reaction rate which, in turn, significantly increases the methanol conversion. The methanol conversion is also improved by decreasing the Reynolds number or increasing the S/C molar ratio. When the serpentine flow field of the channel is heated either through top plate (Y = 1) or the bottom plate (Y = 0), we observe a higher degree of methanol conversion for the case with top plate heating. This is due to the stronger chemical reaction for the case with top plate heating.     

Screening,optimization and kinetics of Jatropha curcas oil transesterification with heterogeneous catalysts

This work investigates the production of fatty acid methyl esters (FAME) from Jatropha curcas oil using a variety of heterogeneous catalysts: resins, zeolites, clays, hydrotalcites, aluminas and niobium oxide. For this purpose, a catalyst screening was first conducted in a batch reactor at the following operating conditions: oil to methanol molar ratio of 1:9, 6 h of reaction, 5 wt% catalyst, at 333 and 393 K. From the screening step, KSF clay and Amberlyst 15 catalysts were selected to carry out a 2³ full factorial central composite rotatable design so as to elucidate the effects of process variables on FAME yield. The optimum reaction conditions for both catalysts were found to be oil to methanol molar ratio of 1:12, 5 wt% of catalyst, 433 K and 6 h of reaction with a FAME yield of about 70 wt%. A kinetic study was then experimentally performed and a semi-empirical model was built to represent the experimental data. Finally, catalyst re-utilization in five successive batch experiments was evaluated at the optimized conditions.     

Biodiesel production from palm oil via heterogeneous transesterification

This paper presents the study of the transesterification of palm oil via heterogeneous process using montmorillonite KSF as heterogeneous catalyst. This study was carried out using a design of experiment (DOE), specifically response surface methodology (RSM) based on four-variable central composite design (CCD) with α (alpha) = 2. The transesterification process variables were reaction temperature, x₁ (50–190 °C), reaction period, x₂ (60–300 min), methanol/oil ratio, x₃ (4–12 mol mol^?1) and amount of catalyst, x₄ (1–5 wt%). It was found that the yield of palm oil fatty acid methyl esters (FAME) could reach up to 79.6% using the following reaction conditions: reaction temperature of 190 °C, reaction period at 180 min, ratio of methanol/oil at 8:1 mol mol^?1 and amount of catalyst at 3%.     

Experimental and kinetic modeling study of methyl butanoate and methyl butanoate/methanol flames at different equivalence ratios and C/O ratios

Premixed laminar methyl butanoate/oxygen/argon and methyl butanoate/methanol/oxygen/argon flames were studied with tunable synchrotron vacuum ultraviolet (VUV) photoionization and molecular-beam sampling mass spectrometry at 30 torr (4.0 kPa). Three flames were investigated in the experiment: MB (methyl butanoate) flame F1.54 (? = 1.54, C/O = 0.479), MB flame F1.67 (? = 1.67, C/O = 0.511) and MB/methanol flame F1.67M (? = 1.67, C/O = 0.479). By measuring the signal intensities at different distances from the burner surface, the mole fraction profiles of intermediates are derived. Experimental results show that the flame front shifts downstream and peak mole fractions of intermediates increase remarkably with the increase of equivalence ratio for pure MB fuel. When methanol is added, the peak mole fractions of most intermediates including those of soot precursors decrease remarkably at the same equivalence ratio, while peaks of soot precursors vary little (only slightly decreasing) at same C/O ratio. It is concluded that the formation of soot precursors is more sensitive to C/O ratio than to equivalence ratio. Besides, more CO₂ is produced near the burner surface in MB flame than that in MB/methanol flame, and this validates an early production of CO₂ in methyl ester oxidation. In addition, a modified MB detailed mechanism is used to model flame structure, and improved agreements between the experimental and predicted results are realized. Based on the simulation results, reaction flux and sensitivity are analyzed for CO₂ and C₃H₃, respectively.     

Biodiesel production from jatropha oil (Jatropha curcas) with high free fatty acids: An optimized process

Response surface methodology (RSM) based on central composite rotatable design (CCRD) was used to optimize the three important reaction variables—methanol quantity (M), acid concentration (C) and reaction time (T) for reduction of free fatty acid (FFA) content of the oil to around 1% as compared to methanol quantity (M′) and reaction time (T′) and for carrying out transesterification of the pretreated oil. Using RSM, quadratic polynomial equations were obtained for predicting acid value and transesterification. Verification experiments confirmed the validity of both the predicted models. The optimum combination for reducing the FFA of Jatropha curcas oil from 14% to less than 1% was found to be 1.43% v/v H₂SO₄ acid catalyst, 0.28 v/v methanol-to-oil ratio and 88-min reaction time at a reaction temperature of 60 °C as compared to 0.16 v/v methanol-to-pretreated oil ratio and 24 min of reaction time at a reaction temperature of 60 °C for producing biodiesel. This process gave an average yield of biodiesel more than 99%. The fuel properties of jatropha biodiesel so obtained were found to be comparable to those of diesel and confirming to the American and European standards.     

Continuous esterification for biodiesel production from palm fatty acid distillate using economical process

An overflow system for continuous esterification of palm fatty acid distillate (PFAD) using an economical process was developed using a continuous stirred tank reactor (CSTR). Continuous production compared to batch production at the same condition had higher product purity. The optimum condition for the esterification process was a 8.8:1:0.05 molar ratio of methanol to PFAD to sulfuric acid catalyst, 60 min of residence time at 75 °C under its own pressure. The free fatty acid (FFA) content in the PFAD was reduced from 93 to less than 1.5%wt by optimum esterification. The esterified product had to be neutralized with 10.24%wt of 3 M sodium hydroxide in water solution at a reaction temperature of 80 °C for 20 min to reduce the residual FFA and glycerides. The components and properties of fatty acid methyl ester (FAME) could meet the standard requirements for biodiesel fuel. Eventually the production costs were calculated to disclose its commercialization.     

Biodiesel from palm oil via loading KF/Ca–Al hydrotalcite catalyst

The solid base catalyst KF/Ca–Al hydrotalcite was obtained from Ca–Al layered double hydroxides and successfully used in the transesterification of methanol with palm oil to produce biodiesel. With the load of KF, the activity of Ca–Al mixed-oxides had been improved much. For the mass ratio 80 wt.%(KF·6H₂O to Ca–Al mixed-oxides) catalyst, under the optimal condition: 338 K, catalyst amount 5%(wt./wt. oil) and methanol/oil molar ratio 12:1, after 5 h reaction, the fatty acid methyl esters yield could reach 97.98%; for the mass ratio 100 wt.%(KF·6H₂O to Ca–Al mixed-oxides) ones, under the same reaction condition, only needed 3 h to get the FAME yield of 99.74%, and even only reacted 1 h, the FAME yield could obtain 97.14%.     

Acid-catalyzed production of biodiesel from waste frying oil

The reaction kinetics of acid-catalyzed transesterification of waste frying oil in excess methanol to form fatty acid methyl esters (FAME), for possible use as biodiesel, was studied. Rate of mixing, feed composition (molar ratio oil:methanol:acid) and temperature were independent variables. There was no significant difference in the yield of FAME when the rate of mixing was in the turbulent range 100 to 600 rpm. The oil:methanol:acid molar ratios and the temperature were the most significant factors affecting the yield of FAME. At 70 °C with oil:methanol:acid molar ratios of 1:245:3.8, and at 80 °C with oil:methanol:acid molar ratios in the range 1:74:1.9–1:245:3.8, the transesterification was essentially a pseudo-first-order reaction as a result of the large excess of methanol which drove the reaction to completion (99±1% at 4 h). In the presence of the large excess of methanol, free fatty acids present in the waste oil were very rapidly converted to methyl esters in the first few minutes under the above conditions. Little or no monoglycerides were detected during the course of the reaction, and diglycerides present in the initial waste oil were rapidly converted to FAME.     

Comparison of biodiesel production from crude Jatropha oil and Krating oil by supercritical methanol transesterification

This work compared the production of biodiesel from two different non-edible oils with relatively high acid values (Jatropha oil and Krating oil). Using non-catalytic supercritical methanol transesterification, high methyl ester yield (85–90%) can be obtained in a very short time (5–10 min). However, the dependence of fatty acid methyl ester yield on reaction conditions (i.e., temperature and pressure) and the optimum conditions were different by the source of oils and were correlated to the amount of free fatty acids (FFAs) and unsaturated fatty acid content in oils. Krating oil, which has higher FFAs and unsaturated fatty acid content, gave higher fatty acid methyl ester yield of 90.4% at 260 °C, 16 MPa, and 10 min whereas biodiesel from Jatropha oil gave fatty acid methyl ester yield of 84.6% at 320 °C, 15 MPa and 5 min using the same molar ratio of methanol to oil 40:1. The product quality from crude Krating oil met the biodiesel standard. Pre-processing steps such as degumming or oil purification are not necessary.     

A comparative study of KOH/Al2O3 and KOH/NaY catalysts for biodiesel production via transesterification from palm oil

The transesterification of palm oil to methyl esters (biodiesel) was studied using KOH loaded on Al₂O₃ and NaY zeolite supports as heterogeneous catalysts. Reaction parameters such as reaction time, wt% KOH loading, molar ratio of oil to methanol, and amount of catalyst were optimized for the production of biodiesel. The 25 wt% KOH/Al₂O₃ and 10 wt% KOH/NaY catalysts are suggested here to be the best formula due to their biodiesel yield of 91.07% at temperatures below 70 °C within 2–3 h at a 1:15 molar ratio of palm oil to methanol and a catalyst amount of 3–6 wt%. The leaching of potassium species in both spent catalysts was observed. The amount of leached potassium species of the KOH/Al₂O₃ was somewhat higher compared to that of the KOH/NaY catalyst. The prepared catalysts were characterized by using several techniques such as XRD, BET, TPD, and XRF.     

Optimization of transesterification conditions for the production of fatty acid methyl ester (FAME) from Chinese tallow kernel oil with surfactant-coated lipase

Surfactant-coated lipase was used as a catalyst in preparing fatty acid methyl ester (FAME) from Chinese tallow kernel oil from Sapium sebiferum (L.) Roxb. syn. Triadica sebifera (L.) small. FAME transesterification was analyzed using response surface methodology to find out the effect of the process variables on the esterification rate and to establish prediction models. Reaction temperature and time were found to be the main factors affecting the esterification rate with the presence of surfactant-coated lipase. Developed prediction models satisfactorily described the esterification rate as a function of reaction temperature, time, dosage of surfactant-coated lipase, ratio of methanol to oil, and water content. The FAME mainly contained fatty acid esters of C16:0, C18:0, C18:1, C18:2, and C18:3, determined by a gas chromatograph. The optimal esterification rate was 93.86%. The optimal conditions for the above esterification ratio were found to be a reaction time of 9.2 h, a reaction temperature of 49 °C, dosage of surfactant-coated lipase of 18.5%, a ratio of methanol to oil of 3:1, and water content of 15.6%. Thus, by using the central composite design, it is possible to determine accurate values of the transesterification parameters where maximum production of FAME occurs using the surfactant-coated lipase as a transesterification catalyst.     

Critical heat flux on flow boiling of methanol–water mixtures in a diverging microchannel with artificial cavities

This study constitutes an experimental investigation into the convective boiling heat transfer and critical heat flux (CHF) of methanol–water mixtures in a diverging microchannel with artificial cavities. Flow visualization shows that bubbles are generally nucleated at both the artificial cavities and side walls of the channel. This confirms the proper functioning of such artificial cavities. Consequently, the wall superheat of the onset nucleate boiling is significantly reduced. Experimental results show that the boiling heat transfer and CHF are significantly influenced by the molar fraction (x_m) as well as the mass flux. The CHF increases with an increase in mass flux at the same molar fraction. On the other hand, the CHF increases slightly from x_m = 0 to 0.3, and then decreases rapidly from x_m = 0.3 to 1 at the same mass flux. The maximum CHF is reached at x_m = 0.3, particularly for a mass flux of 175 kg/m² s, due to the Marangoni effect. Flow visualization confirms that the Marangoni effect helps a region with a liquid film breakup persist to a higher heat flux, and therefore a higher CHF. Moreover, a new empirical correlation involving the Marangoni effect for the CHF on the flow boiling of methanol–water mixtures is developed. The present correlation prediction shows excellent agreement with the experimental data, and further confirms that the present correlation may predict the Marangoni effect on the CHF for the convective boiling heat transfer of binary mixtures.     

LiMn2O4 cathode materials synthesized by the cellulose–citric acid method for lithium ion batteries

A new technique was employed to synthesize spinel LiMn₂O₄ cathode materials by adding cellulose and citric acid to an aqueous solution of lithium and manganese salts. Various synthesis conditions such as the calcination temperature and the citric acid-to-metal ion molar ratio (R) were investigated to determine the ideal conditions for preparing LiMn₂O₄ with the best electrochemical characteristics. The optimal synthesis conditions were found to be R = 1/3 and a calcination temperature of 800 °C. The initial discharge capacity of the material synthesized using the optimal conditions was 134 mAh g⁻¹, and the discharge capacity after 40 cycles was 125 mAh g⁻¹, at a current density of 0.15 mA cm⁻² between 3.0 and 4.35 V. Details of how the initial synthesis conditions affected the capacity and cycling performance of LiMn₂O₄ are discussed.     

Optimal design of geometric parameters of double-layered microchannel heat sinks

This work uses an optimization procedure consisting of a simplified conjugate-gradient method and a three-dimensional fluid flow and heat transfer model to investigate the optimal geometric parameters of a double-layered microchannel heat sink (DL-MCHS). The overall thermal resistance R_T is the objective function to be minimized, and the number of channels N, channel width ratio β, lower channel aspect ratio α_l, and upper channel aspect ratio α_u are the search variables. For a given bottom area (10 × 10 mm) and heat flux (100 W/cm²), the optimal (minimum) thermal resistance of the double-layered microchannel heat sink is about R_T = 0.12 °C/m²W. The corresponding optimal geometric parameters are N = 73, β = 0.50, α_l = 3.52, and, α_u = 7.21 under a total pumping power of 0.1 W. These parameters reduce the overall thermal resistance by 52.8% compared to that yielded by an initial guess (N = 112, β = 0.37, α_l = 10.32, and α_u = 10.93). Furthermore, the optimal thermal resistance decreases rapidly with the pumping power and then tends to approach an constant value. As the pumping power increases, the optimal values of N, α_l, and α_u increase, whereas the optimal β value decreases. However, increasing the pumping power further is not always cost-effective for practical heat sink designs.     

Performance evaluation of mixed convection in an inclined square channel with uniform temperature walls

Numerical analyses were performed for the effect of inclined angle on the mixing flow in a square channel with uniform temperature walls (T_w = 30 °C) and inlet temperature (T₀ = 10 °C). Three-dimensional governing equations were solved numerically for Re = 100, Pr = 0.72 and various inclined angles (from ?90° to 90°). Three-dimensional behavior of fluid in a channel was examined for each angle. Thermal performance was evaluated using the relationship between Nusselt number ratio and pressure loss ratio with and without buoyancy induced flow as a parameter of inclined angles. High heat transfer and low pressure loss region was from ?15° to ?60° in thermal performance using mean Nusselt number ratio.