Hydrogen addition to tea seed oil biodiesel: Performance and emission characteristics

Compression ignition engines are the dominant tools of the modern human life especially in the field of transportation. But, the increasing problematic issues such as decreasing reserves and environmental effects of diesel fuels which is the energy source of compression ignition engines forcing researchers to investigate alternative fuels for substitution or decreasing the dependency on fossil fuels. The mostly known alternative fuel is biodiesel fuel and many researchers are investigating the possible raw materials for biodiesel production. Also, hydrogen fuel is an alternative fuel which can be used in compression ignition engines for decreasing fuel consumption and hazardous exhaust emissions by enriching the fuel. In this study, influences of hydrogen enrichment to diesel and diesel tea seed oil biodiesel blends (B10 and B20) were investigated on an unmodified compression ignition engine experimentally. In consequence of the experiments, lower torque and higher brake specific fuel consumption data were measured when the engine was fuelled diesel biodiesel blends (B10 and B20) instead of diesel fuel. Also, diesel biodiesel blends increased CO₂ and NO_x emissions while decreasing the CO emissions. Hydrogen enrichment (5 l/m and 10 l/m) was improved the both torque and brake specific fuel consumption for all test fuels. Furthermore, hydrogen enrichment reduced CO and CO₂ emissions due to absence of carbon atoms in the chemical structure for all test fuels. Increasing flow rate of hydrogen fuel from 5 l/m to 10 l/m further improved performance measures and emitted harmful gases except NO_x. The most significant drawback of the hydrogen enrichment was the increased NO_x emissions.     

Biodiesel production from inedible animal tallow and an experimental investigation of its use as alternative fuel in a direct injection diesel engine

In this study, a substitute fuel for diesel engines was produced from inedible animal tallow and its usability was investigated as pure biodiesel and its blends with petroleum diesel fuel in a diesel engine. Tallow methyl ester as biodiesel fuel was prepared by base-catalyzed transesterification of the fat with methanol in the presence of NaOH as catalyst. Fuel properties of methyl ester, diesel fuel and blends of them (5%, 20% and 50% by volume) were determined. Viscosity and density of fatty acid methyl ester have been found to meet ASTM D6751 and EN 14214 specifications. Viscosity and density of tallow methyl esters are found to be very close to that of diesel. The calorific value of biodiesel is found to be slightly lower than that of diesel. An experimental study was carried out in order to investigate of its usability as alternative fuel of tallow methyl ester in a direct injection diesel engine. It was observed that the addition of biodiesel to the diesel fuel decreases the effective efficiency of engine and increases the specific fuel consumption. This is due to the lower heating value of biodiesel compared to diesel fuel. However, the effective engine power was comparable by biodiesel compared with diesel fuel. Emissions of carbon monoxide (CO), oxides of nitrogen (NO_x), sulphur dioxide (SO₂) and smoke opacity were reduced around 15%, 38.5%, 72.7% and 56.8%, respectively, in case of tallow methyl esters (B100) compared to diesel fuel. Besides, the lowest CO, NO_x emissions and the highest exhaust temperature were obtained for B20 among all other fuels. The reductions in exhaust emissions made tallow methyl esters and its blends, especially B20 a suitable alternative fuel for diesel and thus could help in controlling air pollution. Based on this study, animal tallow methyl esters and its blends with petroleum diesel fuel can be used a substitute for diesel in direct injection diesel engines without any engine modification.     

Effect of exhaust gas recirculation on diesel engine nitrogen oxide reduction operating with jojoba methyl ester

Jojoba methyl ester (JME) has been used as a renewable fuel in numerous studies evaluating its potential use in diesel engines. These studies showed that this fuel is good gas oil substitute but an increase in the nitrogenous oxides emissions was observed at all operating conditions. The aim of this study mainly was to quantify the efficiency of exhaust gas recirculation (EGR) when using JME fuel in a fully instrumented, two-cylinder, naturally aspirated, four-stroke direct injection diesel engine. The tests were carried out in three sections. Firstly, the measured performance and exhaust emissions of the diesel engine operating with diesel fuel and JME at various speeds under full load are determined and compared. Secondly, tests were performed at constant speed with two loads to investigate the EGR effect on engine performance and exhaust emissions including nitrogenous oxides (NO_x), carbon monoxide (CO), unburned hydrocarbons (HC) and exhaust gas temperatures. Thirdly, the effect of cooled EGR with high ratio at full load on engine performance and emissions was examined. The results showed that EGR is an effective technique for reducing NO_x emissions with JME fuel especially in light-duty diesel engines. With the application of the EGR method, the CO and HC concentration in the engine-out emissions increased. For all operating conditions, a better trade-off between HC, CO and NO_x emissions can be attained within a limited EGR rate of 5–15% with very little economy penalty.     

Physico-chemical properties of ethanol–diesel blend fuel and its effect on performance and emissions of diesel engines

The effects of different ethanol–diesel blended fuels on the performance and emissions of diesel engines have been evaluated experimentally and compared in this paper. The purpose of this project is to find the optimum percentage of ethanol that gives simultaneously better performance and lower emissions. The experiments were conducted on a water-cooled single-cylinder Direct Injection (DI) diesel engine using 0% (neat diesel fuel), 5% (E5–D), 10% (E10–D), 15% (E15–D), and 20% (E20–D) ethanol–diesel blended fuels. With the same rated power for different blended fuels and pure diesel fuel, the engine performance parameters (including power, torque, fuel consumption, and exhaust temperature) and exhaust emissions [Bosch smoke number, CO, NO_x, total hydrocarbon (THC)] were measured. The results indicate that: the brake specific fuel consumption and brake thermal efficiency increased with an increase of ethanol contents in the blended fuel at overall operating conditions; smoke emissions decreased with ethanol–diesel blended fuel, especially with E10–D and E15–D. CO and NO_x emissions reduced for ethanol–diesel blends, but THC increased significantly when compared to neat diesel fuel.     

Diesel engine performance and exhaust emission analysis using waste cooking biodiesel fuel with an artificial neural network

This study deals with artificial neural network (ANN) modeling of a diesel engine using waste cooking biodiesel fuel to predict the brake power, torque, specific fuel consumption and exhaust emissions of the engine. To acquire data for training and testing the proposed ANN, a two cylinders, four-stroke diesel engine was fuelled with waste vegetable cooking biodiesel and diesel fuel blends and operated at different engine speeds. The properties of biodiesel produced from waste vegetable oil was measured based on ASTM standards. The experimental results revealed that blends of waste vegetable oil methyl ester with diesel fuel provide better engine performance and improved emission characteristics. Using some of the experimental data for training, an ANN model was developed based on standard Back-Propagation algorithm for the engine. Multi layer perception network (MLP) was used for non-linear mapping between the input and output parameters. Different activation functions and several rules were used to assess the percentage error between the desired and the predicted values. It was observed that the ANN model can predict the engine performance and exhaust emissions quite well with correlation coefficient (R) 0.9487, 0.999, 0.929 and 0.999 for the engine torque, SFC, CO and HC emissions, respectively. The prediction MSE (Mean Square Error) error was between the desired outputs as measured values and the simulated values were obtained as 0.0004 by the model.     

Experimental investigation on performance and emission characteristics of waste tire pyrolysis oil–diesel blends in a diesel engine

Disposal of waste tires is one of the most important problems that should be solved. This problem can be solved by considering waste tires for production of hydrogen or fuel for diesel engines. This paper presents the studies on the performance and emission characteristics of a four stroke, four cylinders, naturally aspirated, direct-injected diesel engine running with various blends of waste tire pyrolysis oil (WTPO) with diesel fuel. Fuel properties, engine performance, and exhaust emissions of WTPO and its blends were analyzed and compared with those of petroleum diesel fuel. The experimental results showed that WTPO–diesel blends indicated similar performance with diesel fuel in terms of torque and power output of the test engine. It was found that the blends of pyrolysis oil of waste tire WTPO10 can efficiently be used in diesel engines without any engine modifications.     

Effect of ethanol blending with biodiesel on engine performance and exhaust emissions in a CI engine

The use of biodiesel as an alternative diesel engine fuel is increasing rapidly. However, due to technical deficiencies, they are rarely used purely or with high percentages in unmodified diesel engines. Therefore, in this study, we used ethanol as an additive to research the possible use of higher percentages of biodiesel in an unmodified diesel engine. Commercial diesel fuel, 20% biodiesel and 80% diesel fuel, called here as B20, and 80% biodiesel and 20% ethanol, called here as BE20, were used in a single cylinder, four strokes direct injection diesel engine. The effect of test fuels on engine torque, power, brake specific fuel consumption, brake thermal efficiency, exhaust gas temperature, and CO, CO₂, NO_x and SO₂ emissions was investigated. The experimental results showed that the performance of CI engine was improved with the use of the BE20 especially in comparison to B20. Besides, the exhaust emissions for BE20 were fairly reduced.     

Performance and emission characteristics of a diesel engine using isobutanol–diesel fuel blends

The aim of this study is to investigate the suitability of isobutanol–diesel fuel blends as an alternative fuel for the diesel engine, and experimentally determine their effects on the engine performance and exhaust emissions, namely break power, break specific fuel consumption (BSFC), break thermal efficiency (BTE) and emissions of CO, HC and NO_x. For this purpose, four different isobutanol–diesel fuel blends containing 5, 10, 15 and 20% isobutanol were prepared in volume basis and tested in a naturally aspirated four stroke direct injection diesel engine at full -load conditions at the speeds between 1200 and 2800 rpm with intervals of 200 rpm. The results obtained with the blends were compared to those with the diesel fuel as baseline. The test results indicate that the break power slightly decreases with the blends containing up to 10% isobutanol, whereas it significantly decreases with the blends containing 15 and 20% isobutanol. There is an increase in the BSFC in proportional to the isobutanol content in the blends. Although diesel fuel yields the highest BTE, the blend containing 10% isobutanol results in a slight improvement in BTE at high engine speeds. The results also reveal that, compared to diesel fuel, CO and NO_x emissions decrease with the use of the blends, while HC emissions increase considerably.     

Effect of an emission-reducing soluble hybrid nanocatalyst in diesel/biodiesel blends on exergetic performance of a DI diesel engine

The present study was set to explore the effect of a novel soluble hybrid nanocatalyst in diesel/biodiesel fuel blends on exergetic performance parameters of a DI diesel engine. Experiments were carried out using two types of diesel/biodiesel blends (i.e., B5 and B20) at four concentrations (0, 30, 60 and 90 ppm) of the hybrid nanocatalyst, i.e., cerium oxide immobilized on amide-functionalized multiwall carbon nanotubes (MWCNT). Furthermore, the exergy analysis was performed at five different loads and two engine speeds. The results obtained revealed that the exergetic parameters were profoundly influenced by engine speed and load. In general, increasing engine speed and load increased the magnitude of the destructed exergy. Moreover, the exergy efficiency increased by increasing engine load, while it decreased by elevating engine speed. However, the applied fuel blends had approximately similar exergetic efficiency and sustainability index. Interestingly, a remarkable reduction in emissions was obtained by incorporating the soluble catalyst nanoparticles to the diesel/biodiesel blends. Thus, it could be concluded that the diesel/biodiesel blends containing amide-functionalized MWCNTs-CeO₂ catalyst might substitute the use of pure diesel fuel without any unfavorable change in the exergetic performance parameters of the DI engines.     

A study on performance and exhaust emissions of the steam injected DI diesel engine running with different diesel- conola oil methyl ester blends

Although biodiesels have low emission profiles, the main drawback of using biodiesel in diesel engines is higher NOx. Nowadays, the electronic controlled steam injection is a promising method for NOx control. This study investigates the effects of steam injection with diesel fuel-canola oil methyl ester (COME) blends on the performance and emissions characteristics of a direct injection (DI) single cylinder diesel engine. Steam is injected into the inlet manifold during inlet period. The combustion of diesel-COME blends has been modeled using two zone combustion model. The results have been compared with each other in terms of performance and emissions. The maximum increments in engine torque and power were measured as 2.5% for 10% COME (B10) at 1200 rpm, 2.8% for 20% COME (B20) at 2200 rpm. The effects of steam injection on performance and emissions of the diesel engine running with B10 and B20 COME blends were also investigated. Satisfaction improvements have been obtained with the combination of steam injection and COME blends. The maximum torque of the engine running with B10 and 10% steam ratio combination (B10 + S10) and B20 and 10% steam ratio combinations (B20 + S10) were found as 2.4% at 1400 rpm and 0.6% at 1400 rpm, respectively. Significant reduction has been observed in NOx emission with B10-S10 combination. The reduction rate in NOx emissions were 22% with B10-S10 and 18% with B20-S10 at 1200 rpm. The study showed that steam injection is an effective tool for controlling NOx emissions without performance degradation in the diesel engines fueled with COME blends.     

Experimental investigations of performance and emissions of Karanja oil and its blends in a single cylinder agricultural diesel engine

An experimental investigation has been carried out to analyze the performance and emission characteristics of a compression ignition engine fuelled with Karanja oil and its blends (10%, 20%, 50% and 75%) vis-a-vis mineral diesel. The effect of temperature on the viscosity of Karanja oil has also been investigated. Fuel preheating in the experiments – for reducing viscosity of Karanja oil and blends has been done by a specially designed heat exchanger, which utilizes waste heat from exhaust gases. A series of engine tests, with and without preheating/pre-conditioning have been conducted using each of the above fuel blends for comparative performance evaluation. The performance parameters evaluated include thermal efficiency, brake specific fuel consumption (BSFC), brake specific energy consumption (BSEC), and exhaust gas temperature whereas exhaust emissions include mass emissions of CO, HC, NO and smoke opacity. These parameters were evaluated in a single cylinder compression ignition engine typically used in agriculture sector of developing countries. The results of the experiment in each case were compared with baseline data of mineral diesel. Significant improvements have been observed in the performance parameters of the engine as well as exhaust emissions, when lower blends of Karanja oil were used with preheating and also without preheating. The gaseous emission of oxide of nitrogen from all blends with and with out preheating are lower than mineral diesel at all engine loads. Karanja oil blends with diesel (up to 50% v/v) without preheating as well as with preheating can replace diesel for operating the CI engines giving lower emissions and improved engine performance.     

Comparative performance and emission studies when using olive oil as a fuel supplement in DI and IDI diesel engines

An experimental study is conducted to evaluate and compare the use of a diesel fuel supplement, specifically a 25/75% and a 50/50% blend of waste olive oil and commercial diesel fuel, in a four-stroke, DI (Direct Injection) diesel engine and in a four-stroke, IDI (Indirect Injection) diesel engine having a swirl-combustion chamber. The influence of the blends (diesel fuel+olive oil), for a large range of loads, has been examined on fuel consumption, maximum pressure, exhaust temperature, exhaust smokiness and exhaust-gas emissions such as nitrogen oxides (NO_x), hydrocarbons (HC) and carbon monoxide (CO). The differences in the measured performance and exhaust-emission parameters, from the baseline operation of either engine, are determined and compared. The study shows, for both the DI and IDI engines, a small penalty in specific fuel consumption, a moderate increase in exhaust smokiness and essentially unaltered maximum pressures and exhaust temperatures when using the blends. Also, for both the IDI and DI engines when using the blends, the study shows moderate decreases in emitted nitrogen oxides and increases in hydrocarbons as well as negligible increases in emitted carbon monoxide. Theoretical aspects of diesel engine combustion are used to aid the interpretation of the observed engines' behaviour.     

Biodiesel fuel in diesel micro-turbine engines: Modelling and experimental evaluation

Many performance and emission tests have been carried out in reciprocating diesel engines that use biodiesel fuel over the past years and very few in gas turbine engines. This work aims at assessing the thermal performance and emissions at full and partial loads of a 30 kW diesel micro-turbine engine fed with diesel, biodiesel and their blends as fuel. A cycle simulation was performed using the Gate Cycle GE Enter software to evaluate the thermal performance of the 30 kW micro-turbine engine. Performance and emission tests were carried out on a 30 kW diesel micro-turbine engine installed in the NEST laboratories of the Federal University of Itajubá, and the performance results were compared with those of the simulation. There was a good agreement between the simulations and the experimental results from the full load down to about 50% of the load for diesel, biodiesel and their blends. The biodiesel and its blends used as fuel in micro-turbines led to no significant changes in the engine performance and behaviour compared to diesel fuel. The exhaust emissions were evaluated for pure biodiesel and its blends and conventional diesel. The results revealed that the use of biodiesel resulted in a slightly higher CO, lower NO_x and no SO₂ emissions.     

Crude palm oil fuel for diesel-engines: Experimental and ANN simulation approaches

In the current work, the effect of using CPO (crude palm oil)-OD (ordinary diesel) blends as fuel on the performance of CI (compression ignition) engine is studied. Three different blends of CPO-OD (25%, 50% and 75%) were investigated using direct-injection, stationary diesel engine. The CPO-OD blends were preheated to about 60 °C before the injection to reduce the viscosity of the blends. The experiments were conducted at variable engine speeds (1000 rpm through 3000 rpm) under fixed throttle opening. The results revealed that the CPO-OD exhibited higher torque and power output at engine speeds lower than 2000 rpm, while the BSFC (brake specific fuel consumption) was found to be higher than the OD at the same engine speeds. CPO enhanced the BSFC at higher engine speeds (above 2000 rpm). The CPO-OD blends exhibited lower emissions of NO_x and higher emission of CO compared to the OD.     

CNG-diesel engine performance and exhaust emission analysis with the aid of artificial neural network

This study investigates the use of artificial neural network (ANN) modelling to predict brake power, torque, break specific fuel consumption (BSFC), and exhaust emissions of a diesel engine modified to operate with a combination of both compressed natural gas CNG and diesel fuels. A single cylinder, four-stroke diesel engine was modified for the present work and was operated at different engine loads and speeds. The experimental results reveal that the mixtures of CNG and diesel fuel provided better engine performance and improved the emission characteristics compared with the pure diesel fuel. For the ANN modelling, the standard back-propagation algorithm was found to be the optimum choice for training the model. A multi-layer perception network was used for non-linear mapping between the input and output parameters. It was found that the ANN model is able to predict the engine performance and exhaust emissions with a correlation coefficient of 0.9884, 0.9838, 0.95707, and 0.9934 for the engine torque, BSFC, NO_x and exhaust temperature, respectively.     

Biofuels and thermal barrier: A review on compression ignition engine performance,combustion and exhaust gas emission

The performance of an internal combustion engine is affected when renewable biofuels are used instead of fossil fuels in an unmodified engine. Various engine modifications were experimented by the researchers to optimise the biofuels operated engine performance. Thermal barrier coating is one of the techniques used to improve the biofuels operated engine performance and combustion characteristics by reducing the heat loss from the combustion chamber. In this study, engine tests results on performance, combustion and exhaust emission characteristics of the biofuels operated thermal barrier coated engines were collated and reviewed. The results found in the literature were reviewed in three scenarios: (i) uncoated versus coated engine for fossil diesel fuel application, (ii) uncoated versus coated engine for biofuels (and blends) application, and (iii) fossil diesel use on uncoated engine versus biofuel (and blends) use on coated engine. Effects of injection timing, injection pressure and fuel properties on thermal barrier coatings were also discussed. The material type, thickness and properties of the coating materials used by the research community were presented. The effectiveness and durability of the coating layer depends on two key properties: low thermal conductivity and high thermal expansion coefficient. The current study showed that thermal barrier coatings could potentially offset the performance drop due to use of biofuels in the compression ignition engines. Improvements of up to 4.6% in torque, 7.8% in power output, 13.4% in brake specific fuel consumption, 15.4% in brake specific energy consumption and 10.7% in brake thermal efficiency were reported when biofuels or biofuel blends were used in the thermal barrier coated engines as compared to the uncoated engines. In coated engines, peak cylinder pressure and exhaust gas temperature were increased by up to 16.3 bar and 14% respectively as compared to uncoated condition. However, changes in the heat release rates were reported to be between ?27% and +13.8% as compared to uncoated standard engine. Reductions of CO, CO₂, HC and smoke emissions were reported by up to 3.8%, 11.1%, 90.9% and 63% respectively as compared to uncoated engines. Significant decreases in the PM emissions were also reported due to use of thermal barrier coatings in the combustion chamber. In contrast, at high speed and at high load operation, increase in the CO and CO₂ emissions were also reported in coated engines. Coated engines gave higher NO_x emissions by about 4–62.9% as compared to uncoated engines. Combined effects of thermal barrier coatings and optimisation of fuel properties and injection parameters produced further performance and emissions advantages compared to only thermal barrier coated engines. Overall, current review study showed that application of thermal barrier coatings in compression ignition engines could be beneficial when biofuels or biofuel blends are used instead of standard fossil diesel. However, more research is needed combining coatings, types of biofuels and other engine modifications to establish a concrete conclusion on the effectiveness of the thermal barrier when biofuels are used in the compression ignition engine. Reduction of NO_x emissions is another important R & D area.     

Direct injection diesel engine performance,emission, and combustion characteristics using diesel fuel,nonedible honne oil methyl ester,and blends with diesel fuel

Honne oil methyl ester (HOME) is produced from a nonedible vegetable oil, namely, honne oil, available abundantly in India. It has remained as an untapped new possible source of alternative fuel that can be used for diesel engines. The present research is aimed at investigating experimentally the performance, exhaust emission, and combustion characteristics of a direct injection diesel engine (single cylinder, water cooled) typically used in agricultural sector over the entire load range when fuelled with HOME and diesel fuel blends, HM20 (20% HOME + 80% diesel fuel)–HM100. The properties of these blends are found to be comparable with diesel fuel conforming to the American and European standards. The combustion parameters of HM20 are found to be slightly better than neat diesel (ND). For other blend ratios, these combustion parameters deviated compared with ND. The performance (brake thermal efficiency (BTE), brake‐specific fuel consumption, and exhaust gas temperature) of HM20 is better than ND. For other blend ratios, BTE is inferior compared with ND. The emissions (CO and SO) of HM20–HM100, throughout the entire load range, are dropped significantly compared with ND. Unburned hydrocarbon emissions of HM20–HM40, throughout the entire load range, is slightly decreased, whereas for other blend ratios, it is increased compared with ND. NO_x emissions of HM20, throughout the entire load range, is slightly increased, whereas for other blend ratios, it is slightly decreased. The reductions in exhaust emissions together with increase in BTE made the blend HM20 a suitable alternative fuel for diesel fuel and thus could help in controlling air pollution. Copyright © 2011 John Wiley & Sons, Ltd.     

Performance, emission and combustion characteristics of biodiesel fuelled variable compression ratio engine

Experiments has been carried out to estimate the performance, emission and combustion characteristics of a single cylinder; four stroke variable compression ratio multi fuel engine fuelled with waste cooking oil methyl ester and its blends with standard diesel. Tests has been conducted using the fuel blends of 20%, 40%, 60% and 80% biodiesel with standard diesel, with an engine speed of 1500 rpm, fixed compression ratio 21 and at different loading conditions. The performance parameters elucidated includes brake thermal efficiency, specific fuel consumption, brake power, indicated mean effective pressure, mechanical efficiency and exhaust gas temperature. The exhaust gas emission is found to contain carbon monoxide, hydrocarbon, nitrogen oxides and carbon dioxide. The results of the experiment has been compared and analyzed with standard diesel and it confirms considerable improvement in the performance parameters as well as exhaust emissions. The blends when used as fuel results in the reduction of carbon monoxide, hydrocarbon, carbon dioxide at the expense of nitrogen oxides emissions. It has found that the combustion characteristics of waste cooking oil methyl ester and its diesel blends closely followed those of standard diesel.     

Performance and emissions characteristics of Jatropha oil (preheated and blends) in a direct injection compression ignition engine

The scarce and rapidly depleting conventional petroleum resources have promoted research for alternative fuels for internal combustion engines. Among various possible options, fuels derived from triglycerides (vegetable oils/animal fats) present promising “greener” substitutes for fossil fuels. Vegetable oils, due to their agricultural origin, are able to reduce net CO₂ emissions to the atmosphere along with import substitution of petroleum products. However, several operational and durability problems of using straight vegetable oils in diesel engines reported in the literature, which are because of their higher viscosity and low volatility compared to mineral diesel fuel.In the present research, experiments were designed to study the effect of reducing Jatropha oil’s viscosity by increasing the fuel temperature (using waste heat of the exhaust gases) and thereby eliminating its effect on combustion and emission characteristics of the engine. Experiments were also conducted using various blends of Jatropha oil with mineral diesel to study the effect of reduced blend viscosity on emissions and performance of diesel engine. A single cylinder, four stroke, constant speed, water cooled, direct injection diesel engine typically used in agricultural sector was used for the experiments. The acquired data were analyzed for various parameters such as thermal efficiency, brake specific fuel consumption (BSFC), smoke opacity, CO₂, CO and HC emissions. While operating the engine on Jatropha oil (preheated and blends), performance and emission parameters were found to be very close to mineral diesel for lower blend concentrations. However, for higher blend concentrations, performance and emissions were observed to be marginally inferior.     

Experimental investigations of performance,emission and combustion characteristics of Karanja oil blends fuelled DICI engine

Vegetables oils are simplest route of biofuel utilization in direct injection compression ignition (DICI) engines however several operational and durability problems are encountered while using straight vegetable oils in CI engines due to their high viscosity and low volatility. Reduction of viscosity by blending or exhaust gas heating leads to savings in chemical processing cost incurred on transesterification. In this experimental study, performance, emission and combustion characteristics of Karanja oil blends (K10, K20, K50 and K100) with mineral diesel were investigated in unheated conditions in a direct injection CI engine at different engine loads and constant engine speed (1500 rpm) vis-à-vis baseline data from mineral diesel. Analysis of performance parameters such as brake specific fuel consumption (BSFC), thermal efficiency, and exhaust gas temperature; mass emissions of various gaseous pollutant species; combustion parameters such as in-cylinder pressure rise, instantaneous heat release and cumulative heat release etc. were carried out. Detailed combustion analysis revealed that the combustion duration increased significantly even with smaller concentration of Karanja oil in the fuel blend. HC, CO and Smoke emissions were found to decrease for 20–50% (v/v) Karanja oil content in the fuel blends.