Performance,emission and combustion characteristics of a variable compression ratio engine using methyl esters of waste cooking oil and diesel blends

The performance, emission and combustion characteristics of a single cylinder four stroke variable compression ratio multi fuel engine when fueled with waste cooking oil methyl ester and its 20%, 40%, 60% and 80% blends with diesel (on a volume basis) are investigated and compared with standard diesel. The suitability of waste cooking oil methyl ester as a biofuel has been established in this study. Bio diesel produced from waste sun flower oil by transesterification process has been used in this study. Experiment has been conducted at a fixed engine speed of 1500 rpm, 50% load and at compression ratios of 18:1, 19:1, 20:1, 21:1 and 22:1. The impact of compression ratio on fuel consumption, combustion pressures and exhaust gas emissions has been investigated and presented. Optimum compression ratio which gives best performance has been identified. The results indicate longer ignition delay, maximum rate of pressure rise, lower heat release rate and higher mass fraction burnt at higher compression ratio for waste cooking oil methyl ester when compared to that of diesel. The brake thermal efficiency at 50% load for waste cooking oil methyl ester blends and diesel has been calculated and the blend B40 is found to give maximum thermal efficiency. The blends when used as fuel results in reduction of carbon monoxide, hydrocarbon and increase in nitrogen oxides emissions.     

Progress in biodiesel processing

Biodiesel is a notable alternative to the widely used petroleum-derived diesel fuel since it can be generated by domestic natural sources such as soybeans, rapeseeds, coconuts, and even recycled cooking oil, and thus reduces dependence on diminishing petroleum fuel from foreign sources. The injection and atomization characteristics of the vegetable oils are significantly different than those of petroleum-derived diesel fuels, mainly as the result of their high viscosities. Modern diesel engines have fuel-injection system that is sensitive to viscosity change. One way to avoid these problems is to reduce fuel viscosity of vegetable oil in order to improve its performance. The conversion of vegetable oils into biodiesel is an effective way to overcome all the problems associated with the vegetable oils. Dilution, micro-emulsification, pyrolysis, and transesterification are the four techniques applied to solve the problems encountered with the high fuel viscosity. Transesterification is the most common method and leads to monoalkyl esters of vegetable oils and fats, now called biodiesel when used for fuel purposes. The methyl ester produced by transesterification of vegetable oil has a high cetane number, low viscosity and improved heating value compared to those of pure vegetable oil which results in shorter ignition delay and longer combustion duration and hence low particulate emissions.     

Analysis of combustion characteristics,engine performance and exhaust emissions of diesel engine fueled with upgraded waste source fuel

Utilization of the waste products as an alternative fuel could reduce the dependence on fossil fuel. The three types of upgraded waste source fuels discussed in this paper were tire derived fuel (TDF), waste plastic disposal fuel (WPD) and upgraded waste cooking oil (UWCO). The detailed combustion pressure showed that kinematic viscosity and cetane number played an important role in determining the combustion quality. TDF's high kinematic viscosity and low cetane number affected its fuel vaporization process; thus, lengthening its ignition delay. UWCO showed the 14% higher power and 13.8% higher torque compared to diesel fuel (DF). WPD produced the lowest NOx due to its low pressure curve during combustion. TDF had produced the highest exhaust emissions (CO, CO₂, NO and NOx). Particulate matter (PM) emissions by UWCO blends were lower than DF. UWCO's soot concentration was 40% lower than DF and increased to 62.5% from low to high engine speed operation.     

The effects of Al2O3–TiO2 coating in a diesel engine on performance and emission of corn oil methyl ester

Today, as a result of increase in oil prices, limited fossil fuel resources, environmental consideration and global warming, the methyl ester fuels have been focused on alternative fuels. Methyl ester fuels can be used more efficiently in low heat rejection engines (LHR), in which the temperature of combustion chamber is increased by creating a thermal barrier. In this study, the piston, cylinder head, exhaust and inlet valves of a diesel engine were coated with the ceramic material Al₂O₃–TiO₂ by the plasma spray method. Thus, a thermal barrier was provided for the parts of the combustion chamber with these coatings. The effects of corn oil methyl ester that produced by the transesterification method, and No. D2 fuels’ performance and exhaust emissions’ rate were studied by using equal in every respect coated and uncoated engines. Tests were performed on the uncoated engine, and then repeated on the coated engine and the results were compared. A decrease in engine power and specific fuel consumption, as well as significant improvements in exhaust gas emissions (except NOx), were observed for all test fuels used in the coated engine compared with that of the uncoated engine.     

A comparative evaluation of compression ignition engine characteristics using methyl and ethyl esters of Karanja oil

This paper investigates the scope of utilizing biodiesel developed from both through the methyl as well as ethyl alcohol route (methyl and ethyl ester) from Karanja oil as an alternative diesel fuel. The major problem of using neat Karanja oil as a fuel in a compression ignition engine arises due to its very high viscosity. Transesterification with alcohols reduces the viscosity of the oil and other properties have been evaluated to be comparable with those of diesel. In the present work, methyl and ethyl esters of Karanja oil were prepared by transesterification using both methanol and ethanol. The physical and chemical properties of ethyl esters were comparable with that of methyl esters. However, viscosity of ethyl esters was slightly higher than that of methyl esters. Cold flow properties of ethyl esters were better than those of methyl esters. Performance and exhaust emission characteristics of the engine were determined using petrodiesel as the baseline fuel and several blends of diesel and biodiesel as test fuels. Results show that methyl esters produced slightly higher power than ethyl esters. Exhaust emissions of both esters were almost identical. These studies show that both methyl and ethyl esters of Karanja oil can be used as a fuel in compression ignition engine without any engine modification.     

Optimization of neem methyl ester from transesterification process and fuel characterization as a diesel substitute

The present work aimed at the standardization of transesterification process parameters for the production of methyl ester of filtered neem oil and fuel characterization for engine performance. The effect of process parameters such as molar ratio, preheating temperature, catalyst concentration and reaction time was studied to standardize the transesterification process for estimating the highest recovery of ester with lowest possible viscosity. Based on the observations of the ester recovery and kinematic viscosity, it was found that filtered neem oil at 6:1 M ratio (methanol to oil) preheated at 55 °C temperature and maintaining 60 °C reaction temperature for 60 min in the presence of 2 percent KOH and then allowed to settle for 24 h in order to get lowest kinematic viscosity (2.7 cSt) with ester recovery (83.36%). Different fuel properties of the neem methyl ester and neem oil were also measured. Results show that the methyl ester of neem obtained under the optimum condition is an excellent substitute for fossil fuels.     

Synergistic effect of hydrogen and waste lubricating oil on the performance and emissions of a compression ignition engine

The demand for energy is increasing every year. For a long time, fossil fuels have been used to satiate this energy demand. However, using hydrocarbon-based fossil fuels has led to an enormous rise of carbon dioxide levels in the atmosphere resulting in global warming. It is therefore necessary to look for alternatives to fossil fuels. The research carried out till date have shown biomass and waste-derived fuels as plausible alternatives to fossil fuels. The biomass feedstock includes jatropha oil, Karanja oil, cottonseed oil, and hemp oil among others and wastes include used cooking oil, used engine oil, used tire and used plastics etc. In this study, the authors aim to explore waste lubrication oil as a fuel for the diesel engine. The used lubrication oil was pyrolyzed and diesel-like fuel with 80% conversion efficiency was obtained. A blend of the fuel and diesel in the ratio of 80:20 on volume basis was prepared. Engine experiments at various load conditions was carried out with the blend. As compared to diesel, a 2% increase in thermal efficiency, 6.3%, 16.1% and 13.6% decrease in smoke, CO and HC emissions & 3.2% and 1.8% increase in NOx and CO₂ emission were observed at full load with the blend. With an aim to further improve the engine performance and reduce the overall emissions from the engine exhaust, a zero-carbon fuel namely gaseous hydrogen was inducted in the intake manifold. The flow rate of hydrogen was varied from 3 to 12 Litres per minute (LPM). As compared to diesel, at maximum hydrogen flow rate the thermal efficiency increased by 12.2%. HC, CO and smoke emissions decreased by 42.4%, 51.6% and 16.8%, whereas NOx emissions increased by 22%. The study shows that the combination of pyrolyzed waste lubricant and hydrogen were found to be suitable as a fuel for an unmodified diesel engine. Such fuel combination can be used for stationary applications such as power backups.     

Mathematical Relationships Derived from Biodiesel Fuels

Abstract

The objective of this study was to estimate mathematical relationships derived from biodiesel fuels from various vegetable oils by non-catalytic supercritical methanol and ethanol method. The vegetable oils are all extremely viscous with viscosities ranging from 10 to 20 times greater than petroleum diesel fuel. The aim of the transesterification process is to lower the viscosity of the oil. Methyl and ethyl esters as biodiesels were prepared from vegetable oils through transesterification by non-catalytic supercritical fluids. The biodiesels were characterized for their physical and main fuel properties including viscosity, density, flash point and higher heating value (HHV). The viscosities of biodiesels (3–5 mm²/s at 311 K) were much less than those of pure oils (27–54 mm²/s at 311 K), and their HHVs of approximately 40.5 MJ/kg were 10% less than those of petrodiesel fules (～45 MJ/kg). The most important variables affecting the ester yield during the transesterification reaction are molar ratio of alcohol to vegetable oil and reaction temperature. The viscosity values of vegetable oil methyl esters highly decreases after transesterification process. Compared to no. 2 diesel fuel, all of the vegetable oil methyl esters were slightly viscous. The flash point values of vegetable oil methyl esters are highly lower than those of vegetable oils. The flash point values of vegetable oil methyl esters are highly lower than those of vegetable oils. There is high regression between density and viscosity values vegetable oil methyl esters. The relationships between viscosity and flash point for vegetable oil methyl esters are considerably regular.     

Experimental study and empirical correlation development of fuel properties of waste cooking palm biodiesel and its diesel blends at elevated temperatures

In this experimental work, the density, dynamic viscosity and higher heating value of methyl ester based waste cooking palm-biodiesel oil (WMEPB) was investigated under varying temperature and blend ratio condition with No. 2 diesel fuel. The transesterified fatty acid methyl ester of palm vegetable oil collected from local food and beverage shops was used as neat biodiesel. Four different fuel blends (20%, 40%, 60% and 80% by volume mixing with base diesel) were studied along with base No. 2 diesel fuel and pure biodiesel. Tests for dynamic viscosity and density were performed in the temperature range 0–130 °C for each fuel sample whereas the higher heating values were determined at 25 °C room temperature condition. It is found that pure biodiesel has the highest density and dynamic viscosity at a given temperature whereas it exhibits lowest combustion heating value among the six fuels. Moreover, the density for each fuel sample decreases linearly with the increase in temperature. On the other hand, the dynamic viscosity decreases exponentially with the temperature for each fuel sample. In addition, based on the experimental results, regression correlations have been proposed for the density, dynamic viscosity, and higher heating value of the fuels. Subsequently, comprehensive error analyses of these proposed correlations were performed. In particular, the correlation for density and dynamic viscosity were respectively compared with Kay's mixing rule and Grunberg-Nissan mixing rule theory in order to validate their applicability. It is found that density correlations predicted within ±0.3% average error band. And, as high as 72.2% of the dynamic viscosity data were in the range of ±5% average error while the remaining data fell within ±10% error range. And finally, through a comparative study with the available fuel property results of fresh methyl ester palm biodiesel, it is found that available existing correlations derived from fresh palm biodiesel studies can not accurately predict the fuel properties of same waste biodiesel and its blends with diesel.     

Production of biodiesel fuels from linseed oil using methanol and ethanol in non-catalytic SCF conditions

Methyl and ethyl esters as biodiesel fuels were prepared from linseed oil with transesterification reaction in non-catalytic supercritical fluids conditions. Biodiesel fuel is a renewable substitute fuel for petroleum diesel fuel made from vegetable or animal fats. Biodiesel fuel has better properties than that of petroleum diesel fuel such as renewable, biodegradable, non-toxic, and essentially free of sulfur and aromatics. The purpose of the transesterification process is to lower the viscosity of the oil. The viscosity values of linseed oil methyl and ethyl esters highly decreases after transesterification process. The viscosity values of vegetable oils vary between 27.2 and 53.6 mm² s^?1, whereas those of vegetable oil methyl esters between 3.59 and 4.63 mm² s^?1. Compared with no. 2 diesel fuel, all of the vegetable oil methyl esters were slightly viscous. The flash point values of vegetable oil methyl esters are highly lower than those of vegetable oils. The transesterification of linseed oil in supercritical fluids such as methanol and ethanol has proved to be the most promising process. Methanol is the commonly used alcohol in this process, due in part to its low cost. Methyl esters of vegetable oils have several outstanding advantages among other new-renewable and clean engine fuel alternatives. The most important variables affecting the methyl ester yield during the transesterification reaction are molar ratio of alcohol to vegetable oil and reaction temperature. Biodiesel has become more attractive recently because of its environmental benefits. Biodiesel is an environmentally friendly fuel that can be used in any diesel engine without modification.     

Emission and performance characteristics of an indirect ignition diesel engine fuelled with waste cooking oil

Biofuel has so far been backed by government policies in the quest for low carbon fuel in the near future and promises to ensure energy security through partially replacing fossil fuels. At present biodiesel is mostly produced by transesterification reaction from oil-seed feedstock and has to conform to ASTM D6751 specifications. Biodiesel sustainability has sparked debate on the pros and cons of biodiesel and the question of food security. The use of waste cooking oil such as palm and coconut oil in diesel engines is more sustainable if they can perform similarly to ordinary diesel fuel (B0). This paper presents the experimental study carried out to evaluate emission and performance characteristics of a multi-cylinder diesel engine operating on waste cooking oil such as 5% palm oil with 95% ordinary diesel fuel (P5) and 5% coconut oil with 95% ordinary diesel fuel (C5). B0 was used for comparison purposes. The results show that there are reductions in brake power of 1.2% and 0.7% for P5 and C5 respectively compared with B0. In addition, reduction of exhaust emissions such as unburned hydrocarbon (HC), smoke, carbon mono-oxide (CO), and nitrogen oxides (NO_x) is offered by the blended fuels.     

Biodiesel production from vegetable oils via catalytic and non-catalytic supercritical methanol transesterification methods

This paper reviews the production and characterization of biodiesel (BD or B) as well as the experimental work carried out by many researchers in this field. BD fuel is a renewable substitute fuel for petroleum diesel or petrodiesel (PD) fuel made from vegetable or animal fats. BD fuel can be used in any mixture with PD fuel as it has very similar characteristics but it has lower exhaust emissions. BD fuel has better properties than that of PD fuel such as renewable, biodegradable, non-toxic, and essentially free of sulfur and aromatics. There are more than 350 oil bearing crops identified, among which only sunflower, safflower, soybean, cottonseed, rapeseed and peanut oils are considered as potential alternative fuels for diesel engines. The major problem associated with the use of pure vegetable oils as fuels, for Diesel engines are caused by high fuel viscosity in compression ignition. Dilution, micro-emulsification, pyrolysis and transesterification are the four techniques applied to solve the problems encountered with the high fuel viscosity. Dilution of oils with solvents and microemulsions of vegetable oils lowers the viscosity, some engine performance problems still exist. The viscosity values of vegetable oils vary between 27.2 and 53.6 mm²/s whereas those of vegetable oil methyl esters between 3.59 and 4.63 mm²/s. The viscosity values of vegetable oil methyl esters highly decreases after transesterification process. Compared to no. 2 diesel fuel, all of the vegetable oil methyl esters were slightly viscous. The flash point values of vegetable oil methyl esters are highly lower than those of vegetable oils. An increase in density from 860 to 885 kg/m³ for vegetable oil methyl esters or biodiesels increases the viscosity from 3.59 to 4.63 mm²/s and the increases are highly regular. The purpose of the transesterification process is to lower the viscosity of the oil. The transesterfication of triglycerides by methanol, ethanol, propanol and butanol, has proved to be the most promising process. Methanol is the commonly used alcohol in this process, due in part to its low cost. Methyl esters of vegetable oils have several outstanding advantages among other new-renewable and clean engine fuel alternatives. The most important variables affecting the methyl ester yield during the transesterification reaction are molar ratio of alcohol to vegetable oil and reaction temperature. Biodiesel has become more attractive recently because of its environmental benefits. Biodiesel is an environmentally friendly fuel that can be used in any diesel engine without modification.     

An outcome of quaternary fuel blended Fe3O4-doped reduced graphene oxide nanocomposite on the diesel engine

The study includes the use of alcohols in conjunction with diesel as a binary fuel and biodiesel. In addition, this study was conducted on quaternary fuels (premium diesel, waste cooking biodiesel, n-butanol, and bioethanol), including Fe₃O₄ (iron(III) oxide)-doped reduced graphene oxide (rGO) nanocomposite to reduce the use of fossil fuels, their cost, and energy demand. It includes 10% bioethanol, 5%–20% n-butanol, 25 ppm Fe₃O₄-doped rGO nanocomposite, and 20% and 100% waste cooking biodiesel, all of which have been tested in a diesel engine to ensure that they are suitable for use. The findings were compared to those obtained with premium diesel, ranging from 50% to 100% at full engine load conditions. In comparison to 100% premium diesel fuel, the fuel blend (Blend G) had 37.50% brake thermal efficiency and 0.46% (brake-specific energy consumption), as well as lower rates of 316.2% carbon monoxide, 198.80% hydrocarbon, and 80.01% smoke with 28.10% higher oxides of nitrogen (NOx). Adding 20% n-butanol to premium diesel, as well as waste cooking biodiesel, bioethanol, and Fe₃O₄-doped rGO nanocomposite fuel blends, was used in this study to improve the performance of the diesel engine and reduce some of the NOx emissions. In the near future, these fuel blends may be a viable alternative combination for the diesel engine.     

Energy,exergy and emission analysis on a DI single cylinder diesel engine using pyrolytic waste plastic oil diesel blend

Depletion of fossil fuels and stringent emission norms focus attention to discover an evitable source of alternative fuel in order to attribute a significant compensation on conventional fuels. Besides, waste management policies encourage the valorization of different wastes for the production of alternative fuels in order to reduce the challenges of waste management. In this context, pyrolysis has become an emerging trend to convert different wastes into alternate fuel and suitable to be used as a substitute fuel for CI engines. The current investigation provides a sustainable and feasible solution for waste plastic management by widening the gap between global plastic production and plastic waste generation. It investigates the performance and emission of a single cylinder DI four stroke diesel engine using waste plastic oil (WPO) derived from pyrolysis of waste plastics using Zeolite-A as catalyst. Engine load tests have been conducted taking waste plastic oil and subsequently a blend of waste plastic oil by 10%, 20%, and 30% in volume proportions with diesel as fuel. The performance of the test engine in terms of brake thermal efficiency is found marginally higher and brake specific fuel consumption comparatively lowest for 20% WPO-diesel blend than pure diesel. The NOx and HC emission is found lower under low load condition and became higher by increasing the load as compared to diesel. Fuel exergy was significantly increasing after blending of WPO with pure diesel, but exergetic efficiency of the blended fuels followed the reverse trend. However, increase in load of the engine improved the exergetic efficiency. The 20% WPO–diesel blended fuel is found suitable to be used as an alternative fuel for diesel engine.     

Effect of Cotton Seed Oil Methyl Ester on the Performance and Exhaust Emission of a Diesel Engine

Numerous studies indicated that oil sources in the world will come to an end. As a result, new alternative energy sources will be required to substitute for oil. Some of the experimental studies showed that vegetable oil can be used as alternative fuel in diesel engines. The viscosity of vegetable oil is much higher than that of standard diesel fuel; therefore, the high viscosity of the vegetable oil can cause problems for injection systems and engine components. To decrease viscosity, cottonseed methyl ester was obtained from raw cottonseed oil by transesterification method. In this study, cottonseed methyl ester was used in a four-stroke, single cylinder, and air-cooled diesel engine as alternative fuel. Engine tests carried out at full load-different speed range, the engine torque and power of cottonseed oil methyl ester was found to be lower than that of diesel fuel in the range of 3–9% and specific fuel consumption was higher than that of diesel fuel by approximately 8–10%. CO ₂ , CO, and NO _x emissions of cottonseed methyl ester were lower than that of diesel fuel.     

Biodiesel production from inedible animal tallow and an experimental investigation of its use as alternative fuel in a direct injection diesel engine

In this study, a substitute fuel for diesel engines was produced from inedible animal tallow and its usability was investigated as pure biodiesel and its blends with petroleum diesel fuel in a diesel engine. Tallow methyl ester as biodiesel fuel was prepared by base-catalyzed transesterification of the fat with methanol in the presence of NaOH as catalyst. Fuel properties of methyl ester, diesel fuel and blends of them (5%, 20% and 50% by volume) were determined. Viscosity and density of fatty acid methyl ester have been found to meet ASTM D6751 and EN 14214 specifications. Viscosity and density of tallow methyl esters are found to be very close to that of diesel. The calorific value of biodiesel is found to be slightly lower than that of diesel. An experimental study was carried out in order to investigate of its usability as alternative fuel of tallow methyl ester in a direct injection diesel engine. It was observed that the addition of biodiesel to the diesel fuel decreases the effective efficiency of engine and increases the specific fuel consumption. This is due to the lower heating value of biodiesel compared to diesel fuel. However, the effective engine power was comparable by biodiesel compared with diesel fuel. Emissions of carbon monoxide (CO), oxides of nitrogen (NO_x), sulphur dioxide (SO₂) and smoke opacity were reduced around 15%, 38.5%, 72.7% and 56.8%, respectively, in case of tallow methyl esters (B100) compared to diesel fuel. Besides, the lowest CO, NO_x emissions and the highest exhaust temperature were obtained for B20 among all other fuels. The reductions in exhaust emissions made tallow methyl esters and its blends, especially B20 a suitable alternative fuel for diesel and thus could help in controlling air pollution. Based on this study, animal tallow methyl esters and its blends with petroleum diesel fuel can be used a substitute for diesel in direct injection diesel engines without any engine modification.     

Biodiesel production from waste cooking oil using heterogeneous catalysts and its operational characteristics on variable compression ratio CI engine

In the present work, the optimum biodiesel conversion from waste cooking oil to biodiesel through transesterification method was investigated. The base catalyzed transesterification under different reactant proportions such as the molar ratio of alcohol to oil and mass ratio of catalyst to oil was studied for optimum production of biodiesel. The optimum condition for base catalyzed transesterification of waste cooking oil was determined to be 12:1 and 5 wt% of zinc doped calcium oxide. The fuel properties of the produced biodiesel such as the calorific value, flash point and density were examined and compared to conventional diesel. The properties of produced biodiesel and their blend for different ratios (B20, B40, B60, B80 and B100) were comparable with properties of diesel oil and ASTM biodiesel standards. Tests have been conducted on CI engine which runs at a constant speed of 1500 rpm, injection pressure of 200 bar, compression ratio 15:1 and 17.5, and varying engine load. The performance parameters include brake thermal efficiency, brake specific energy consumption and emissions parameters such as Carbon monoxide (CO), Hydrocarbon (HC), Oxides of Nitrogen (NOx) and smoke opacity varying with engine load (BP). Diesel engine's thermal performance and emission parameters such as CO, HC, and NOx on different biodiesel blends demonstrate that biodiesel produced from waste cooking oil using heterogeneous catalyst was suitable to be used as diesel oil blends and had lesser emissions as compared to conventional diesel.     

6BTA 5.9 G2-1 Cummins engine performance and emission tests using methyl ester mahua (Madhuca indica) oil/diesel blends

Neat mahua oil poses some problems when subjected to prolonged usage in CI engine. The transesterification of mahua oil can reduce these problems. The use of biodiesel fuel as substitute for conventional petroleum fuel in heavy-duty diesel engine is receiving an increasing amount of attention. This interest is based on the properties of bio-diesel including the fact that it is produced from a renewable resource, its biodegradability and potential to exhaust emissions. A Cummins 6BTA 5.9 G2- 1, 158 HP rated power, turbocharged, DI, water cooled diesel engine was run on diesel, methyl ester of mahua oil and its blends at constant speed of 1500 rpm under variable load conditions. The volumetric blending ratios of biodiesel with conventional diesel fuel were set at 0, 20, 40, 60, and 100. Engine performance (brake specific fuel consumption, brake specific energy consumption, thermal efficiency and exhaust gas temperature) and emissions (CO, HC and NOx) were measured to evaluate and compute the behavior of the diesel engine running on biodiesel. The results indicate that with the increase of biodiesel in the blends CO, HC reduces significantly, fuel consumption and NOx emission of biodiesel increases slightly compared with diesel. Brake specific energy consumption decreases and thermal efficiency of engine slightly increases when operating on 20% biodiesel than that operating on diesel.     

Biodiesel production through the use of different sources and characterization of oils and their esters as the substitute of diesel: A review

The world is confronted with the twin crises of fossil fuel depletion and environmental degradation. The indiscriminate extraction and consumption of fossil fuels have led to a reduction in petroleum reserves. Petroleum based fuels are obtained from limited reserves. These finite reserves are highly concentrated in certain region of the world. Therefore, those countries not having these resources are facing a foreign exchange crisis, mainly due to the import of crude petroleum oil. Hence it is necessary to look for alternative fuels, which can be produced from materials available within the country. Although vegetative oils can be fuel for diesel engines, but their high viscosities, low volatilities and poor cold flow properties have led to the investigation of its various derivatives. Among the different possible sources, fatty acid methyl esters, known as Biodiesel fuel derived from triglycerides (vegetable oil and animal fates) by transesterification with methanol, present the promising alternative substitute to diesel fuels and have received the most attention now a day. The main advantages of using Biodiesel are its renewability, better quality exhaust gas emission, its biodegradability and the organic carbon present in it is photosynthetic in origin. It does not contribute to a rise in the level of carbon dioxide in the atmosphere and consequently to the green house effect. This paper reviews the source of production and characterization of vegetable oils and their methyl ester as the substitute of the petroleum fuel and future possibilities of Biodiesel production.     

Effect of choice of pilot fuel on the performance of natural gas in diesel engines

Energy conversion alone is inadequate to satisfy long-term energy demands and to gain independence from petroleum-based fuels. It is, therefore, of great importance that all potential fuel alternatives be recognised and examined. Natural gas and bio-liquids may provide such alternatives and their potential has been examined (Nwafor and Rice, WREC 1994;2:841). Fossil fuel combustion is the main culprit in environmental pollution, whilst the impacts of vegetable oil fuel systems are on the whole less adverse and more localised than those of fossil fuels. This paper investigates the possibility of substituting a plant fuel pilot injection for diesel fuel for combustion of natural gas in a diesel engine. The pilot fuels used are rape methyl ester (RME) and neat rapeseed oil. The test results indicate that engine performance on these alternative pilot fuels was satisfactory and compared favourably with the baseline test result on diesel fuel.