Electrodeposition of MWNT/Bi2Te3 Composite Thermoelectric Films

The effect of multiwalled carbon nanotubes (MWNTs) on the electrochemical behavior of the Bi-Te binary system in nitric acid baths was investigated by means of cyclic voltammetry and electrochemical impedance spectroscopy. Based on the results, MWNT/Bi₂Te₃ composite thermoelectric films were prepared by potentiostatic electrodeposition at room temperature. The morphology, composition, and structure of the MWNT/Bi₂Te₃ composite films were analyzed by environmental scanning electron microscopy, energy-dispersive spectroscopy, and x-ray diffraction. The results show that addition of MWNTs to the electrolyte did not change the electrochemical reduction mechanisms of Bi³⁺, HTeO ₂ ⁺ or their mixture, but the reduction processes of Bi³⁺, HTeO ₂ ⁺ , and their mixture become easier. MWNT/Bi₂Te₃ composite thermoelectric films can be obtained by potentiostatic electrodeposition at a wide range of potentials with subsequent annealing. The MWNTs in the films act as nucleation sites for Bi₂Te₃ compound and thereby elevate the film deposition rate. The content of Bi element and MWNTs in the films increased as the potential was shifted negatively. In addition, the MWNTs can enhance the crystallization of Bi₂Te₃ film.     

Fabrication of Superstrong Ultrathin Free‐Standing Single‐Walled Carbon Nanotube Films via a Wet Process

A one‐pot and readily practical approach is described for the preparation of superstrong, ultrathin, free‐standing single‐walled carbon nanotube (SWNT) films. The SWNT films, with controlled thicknesses of tens to hundreds of nanometers, are prepared from commonly commercialized SWNTs via a wet process. The SWNTs could be easily transferred onto any substrates after self‐releasing from filter membranes without further treatment. The obtained films exhibit excellent performances with sheet resistance of 223 Ω sq^?1 and a transparency of 90% at 550 nm was obtained. Most important is that the as‐prepared free‐standing SWNT ultrathin films showed extremely high tensile strength up to 850 MPa for only about a 20‐nm thick film, which has great significance for practical applications, for example, as flexible electrode materials. The SWNT film is used to construct a capacitive touch‐screen prototype, which has a highly sensitive and quick signal touch response.     

Built‐In Haze Glass‐Fabric Reinforced Siloxane Hybrid Film for Efficient Organic Light‐Emitting Diodes (OLEDs)

Substrates with high transmittance and high haze are desired for increasing the light outcoupling efficiency of organic light‐emitting diodes (OLEDs). However, most of the polymer films used as substrate have high transmittance and low haze. Herein, a facile route to fabricate a built‐in haze glass‐fabric reinforced siloxane hybrid (GFRH) film having high total transmittance (≈89%) and high haze (≈89%) is reported using the scattering effect induced by refractive index contrast between the glass fabric and the siloxane hybrid (hybrimer). The hybrimer exhibiting large refractive index contrast with the glass fabric is synthesized by removing the phenyl substituents. Besides its optical properties, the hazy GFRH films exhibit smooth surface (R_sq = 0.2 nm), low thermal expansion (13 ppm °C⁻¹), high chemical stability, and dimensional stability. Owing to the outstanding properties of the GFRH film, OLED is successfully fabricated onto the film exhibiting 74% external quantum efficiency enhancement. The hazy GFRH's unique optical properties, excellent thermal stability, outstanding dimensional stability, and the ability to perform as a transparent electrode enable them as a wide ranging substrate for the flexible optoelectronic devices.     

Highly Flexible Transparent Electrodes Containing Ultrathin Silver for Efficient Polymer Solar Cells

Transparent electrodes (TEs) having electrooptical trade‐offs better than state‐of‐the‐art indium tin oxide (ITO) are continuously sought as they are essential to enable flexible electronic and optoelectronic devices. In this work, a TiO₂‐Ag‐ITO (TAI)‐based TE is introduced and its use is demonstrated in an inverted polymer solar cell (I‐PSCs). Thanks to the favorable nucleation and wetting conditions provided by the TiO₂, the ultrathin silver film percolates and becomes continuous with high smoothness at very low thicknesses (3–4 nm), much lower than those required when it is directly deposited on a plastic or glass substrate. Compared to conventional ITO‐TE, the proposed TAI‐TE exhibits exceptionally lower electrical sheet resistance (6.2 Ω sq^?1), higher optical transmittance, a figure‐of‐merit two times larger, and mechanical flexibility, the latter confirmed by the fact that the resistance increases only 6.6% after 10³ tensile bending cycles. The I‐PSCs incorporating the TAI‐TE show record power conversion efficiency (8.34%), maintained at 96% even after 400 bending cycles.     

Cohesively Enhanced Conductivity and Adhesion of Flexible Silver Nanowire Networks by Biocompatible Polymer Sol–Gel Transition

Silver nanowire (AgNW) networks are a promising candidate to replace indium tin oxide (ITO) as transparent conductors. In this paper, a novel transparent composite conductor composed of AgNW/biocompatible alginate gel on a flexible polyethylene terephthalate (PET) substrate, with synchronously enhanced adhesion and reduced resistivity, is prepared without high‐temperature annealing. The sheet resistance of the flexible AgNW/PET film reduces from 300 to 50.3 Ohm sq^?1 at transmittance of 94%. The optical and electrical performance is superior to that obtained from the flexible ITO film on PET. Meanwhile, the sheet resistance does not show great change after tape test, suggesting a good adhesion of AgNW to the polymer substrate. Moreover, the AgNW composite film shows a good stability to resist long‐term storage, solvent damage, and ultrasonication. Finally, polymer solar cells employing the composite AgNW film as the electrode are realized, displaying an efficiency of 2.44%.     

Electrohydrodynamic NanoDrip Printing of High Aspect Ratio Metal Grid Transparent Electrodes

The transparent conducting electrode is an essential component in many contemporary and future devices, ranging from displays to solar cells. Fabricating transparent electrodes requires a balancing act between sufficient electrical conductivity and high light transmittance, both affected by the involved materials, fabrication methodology, and design. While metal films possess the highest conductivity at room temperature, a decent optical transmittance can only be achieved with ultrathin films. Structuring the metal into optically invisible nanowires has been shown to be promising to complement or even substitute transparent conductive oxides as dominant transparent electrode material. Here the out‐of‐plane fabrication capability of the recently developed method of electrohydrodynamic NanoDrip printing to pattern gold and silver nanogrids with line widths from 80 to 500 nm is demonstrated. This fully additive process enables the printing of high aspect ratio nanowalls and by that significantly improves the electrical performance, while maintaining the optical transmittance at a high level. Metal grid transparent electrodes optimized for low sheet resistances (8 Ω sq^?1 at a relative transmittance of 94%) as well as optimized for high transmittance (97% at a sheet resistance of 20 Ω sq^?1) are reported, which can be tailored on demand for the use in various applications.     

Preparation of High‐Performance Conductive Polymer Fibers through Morphological Control of Networks Formed by Nanofillers

A general method is described to prepare high‐performance conductive polymer fibers or tapes. In this method, bicomponent tapes/fibers containing two layers of conductive polymer composites (CPCs) filled with multiwall carbon nanotubes (MWNT) or carbon black (CB) based on a lower‐melting‐temperature polymer and an unfilled polymer core with higher melting temperature are fabricated by a melt‐based process. Morphological control of the conductive network formed by nanofillers is realized by solid‐state drawing and annealing. Information on the morphological and electrical change of the highly oriented conductive nanofiller network in CPC bicomponent tapes during relaxation, melting, and crystallization of the polymer matrix is reported for the first time. The conductivity of these polypropylene tapes can be as high as 275 S m^?1 with tensile strengths of around 500 MPa. To the best of the authors' knowledge, it is the most conductive, high‐strength polymer fiber produced by melt‐processing reported in literature, despite the fact that only ～5 wt.% of MWNTs are used in the outer layers of the tape and the overall MWNT content in the bicomponent tape can be much lower (typically ～0.5 wt.%). Their applications could include sensing, smart textiles, electrodes for flexible solar cells, and electromagnetic interference (EMI) shielding. Furthermore, a modeling approach was used to study the relaxation process of highly oriented conductive networks formed by carbon nanofillers.     

Flexible transparent conductive film based on silver nanowires and reduced graphene oxide

Silver nanowires (AgNWs) with diameter of 90—150 nm and length of 20—50 μm were successfully synthesized by a polyol process. Graphene oxide (GO) was prepared by Hummers method, and was reduced with strong hydrazine hy-drate at room temperature. The flexible transparent conductive films (TCFs) were fabricated using the mixed cellulose eater (MCE) as matrix and AgNWs and reduced graphene oxide (rGO) as conductive fillers by the improved vacuum fil-tration process. Then, the optical, electrical and mechanical properties of the AgNWs-rGO films were investigated. The results show that for the AgNWs-rGO film produced with the deposition densities of AgNWs and rGO as 110 mg·m-2 and 55 mg·m-2, the optical transmission at 550 nm is 88.4% with Rs around 891 Ω·sq-1, whereas the optical transmission for the AgNWs-rGO film with deposition densities of AgNWs and rGO of 385 mg·m-2 and 55 mg·m-2 is 79.0% at 550 nm with Rs around 9.6 Ω·sq-1. There is little overt increase in Rs of the AgNWS-rGO film after tape tests for 200 times. The bending test results indicate that the change in Rs of AgNWs-MCE film is less than 2% even after 200 cycles of compressive or tensile bending. The excellent mechanical properties of the AgNWs-rGO film can be attributed to the burying of AgNWs and rGO at the surface of MCE     

Spin‐ and Spray‐Deposited Single‐Walled Carbon‐Nanotube Electrodes for Organic Solar Cells

Organic bulk‐heterojunction solar cells using thin‐film single‐walled carbon‐nanotube (SWCNT) anodes deposited on glass are reported. Two types of SWCNT films are investigated: spin‐coated films from dichloroethane (DCE), and spray‐coated films from deionized water using sodium dodecyl sulphate (SDS) or sodium dodecyl benzene sulphonate (SDBS) as the surfactant. All of the films are found to be mechanically robust, with no tendency to delaminate from the underlying substrate during handling. Acid treatment with HNO₃ yields high conductivities >1000 S cm^?1 for all of the films, with values of up to 7694 ± 800 S cm^?1 being obtained when using SDS as the surfactant. Sheet resistances of around 100 Ω sq^?1 are obtained at reasonable transmission, for example, 128 ± 2 Ω sq^?1 at 90% for DCE, 57 ± 3 Ω sq^?1 at 65% for H₂O:SDS, and 68 ± 5 Ω sq^?1 at 70% for H₂O:SDBS. Solar cells are fabricated by successively coating the SWCNT films with poly(3,4‐ethylenedioxythiophene):poly(styrene sulphonate) (PEDOT:PSS), a blend of regioregular poly(3‐hexylthiophene) (P3HT) and 1‐(3‐methoxy‐carbonyl)‐propyl‐1‐phenyl‐(6,6)C₆₁ (PCBM), and LiF/Al. The resultant devices have respective power conversions of 2.3, 2.2 and 1.2% for DCE, H₂O:SDS and H₂O:SDBS, with the first two being at a virtual parity with reference devices using ITO‐coated glass as the anode (2.3%).     

Hybrid Silver Nanowire and Graphene‐Based Solution‐Processed Transparent Electrode for Organic Optoelectronics

The research on transparent conductive electrodes is in rapid ascent in order to respond to the requests of novel optoelectronic devices. The synergic coupling of silver nanowires (AgNWs) and high‐quality solution‐processable exfoliated graphene (EG) enables an efficient transparent conductor with low‐surface roughness of 4.6 nm, low sheet resistance of 13.7 Ω sq^?1 at high transmittance, and superior mechanical and chemical stabilities. The developed AgNWs–EG films are versatile for a wide variety of optoelectronics. As an example, when used as a bottom electrode in organic solar cell and polymer light‐emitting diode, the devices exhibit a power conversion efficiency of 6.6% and an external quantum efficiency of 4.4%, respectively, comparable to their commercial indium tin oxide counterparts.     

Novel Film‐Casting Method for High‐Performance Flexible Polymer Electrodes

A new film‐casting method for polymer electrodes is reported, in which thickness‐controlled drop‐casting (TCDC), using polyaniline doped with camphorsulfonic acid (PANI:CSA) is used. By combining the advantages of conventional spin‐casting and drop‐casting methods, and by rigorously controlling the film formation parameters, flexible polymer electrodes with high conductivity and excellent transmittance can be produced. The PANI:CSA electrodes cast by the TCDC method exhibited constant thickness‐independent conductivities of ～600 S cm^?1 down to a film thickness of 0.2 μm, and a high optical transmittance of about 85% at 550 nm. Furthermore, the new casting method significantly reduced the sheet resistance (～90 Ω/square) of the PANI:CSA electrodes compared with the conventional spin‐cast films, enhancing the performance of the devices deposited on plastic substrates. The flexible polymer light‐emitting diode produced a brightness of 6000 cd m^?2, and the flexible polymer solar cell exhibited a power conversion efficiency of 2%, both of which were much higher than those of the devices fabricated by the conventional spin‐casting method.     

Highly Efficient and Bendable Organic Solar Cells with Solution‐Processed Silver Nanowire Electrodes

Highly efficient and bendable organic solar cells (OSCs) are fabricated using solution‐processed silver nanowire (Ag NW) electrodes. The Ag NW films were highly transparent (diffusive transmittance ≈ 95% at a wavelength of 550 nm), highly conductive (sheet resistance ≈ 10 Ω sq^?1), and highly flexible (change in resistance ≈ 1.1 ± 1% at a bending radius of ≈200 μm). Power conversion efficiencies of ≈5.80 and 5.02% were obtained for devices fabricated on Ag NWs/glass and Ag NWs/poly(ethylene terephthalate) (PET), respectively. Moreover, the bendable devices fabricated using the Ag NWs/PET films decrease slightly in their efficiency (to ≈96% of the initial value) even after the devices had been bent 1000 times with a radius of ≈1.5 mm.     

New Roll‐to‐Roll Processable PEDOT‐Based Polymer with Colorless Bleached State for Flexible Electrochromic Devices

Conjugated electrochromic (EC) polymers for flexible EC devices (ECDs) generally lack a fully colorless bleached state. A strategy to overcome this drawback is the implementation of a new sidechain‐modified poly(3,4‐ethylene dioxythiophene) derivative that can be deposited in thin‐film form in a customized high‐throughput and large‐area roll‐to‐roll polymerization process. The sidechain modification provides enhanced EC properties in terms of visible light transmittance change, Δτ_v = 59% (ΔL* = 54.1), contrast ratio (CR = 15.8), coloration efficiency (η = 530 cm² C^?1), and color neutrality (L* = 83.8, a* = ?4.3, b* = ?4.1) in the bleached state. The intense blue‐colored polymer thin films exhibit high cycle stability (10 000 cycles) and fast response times. The design, synthesis, and polymerization of the modified 3,4‐ethylene dioxythiophene derivative are discussed along with a detailed optical, electrochemical, and spectroelectrochemical characterization of the resulting EC thin films. Finally, a flexible see‐through ECD with a visible light transmittance change of Δτ_v = 47% (ΔL* = 51.9) and a neutral‐colored bleached state is developed.     

Electrically Conductive Thin Films Prepared from Layer‐by‐Layer Assembly of Graphite Platelets

Layer‐by‐layer (LBL) assembly of carbon nanoparticles for low electrical contact resistance thin film applications is demonstrated. The nanoparticles consist of irregularly shaped graphite platelets, with acrylamide/ββ‐methacryl‐oxyethyl‐trimethyl‐ammonium copolymer as the cationic binder. Nanoparticle zeta (ζζ) potential and thereby electrostatic interactions are varied by altering the pH of graphite suspension as well as that of the binder suspension. Film thickness as a function of zeta potential, immersion time, and the number of layers deposited is obtained using Monte Carlo simulation of the energy dispersive spectroscopy measurements. Multilayer film surface morphology is visualized via field‐emission scanning electron microscopy and atomic‐force microscopy. Thin film electrical properties are characterized using electrical contact resistance measurements. Graphite nanoparticles are found to self‐assemble onto gold substrates through two distinct yet overlapping mechanisms. The first mechanism is characterized by logarithmic carbon uptake with respect to the number of deposition cycles and slow clustering of nanoparticles on the gold surface. The second mechanism results from more rapid LBL nanoparticle assembly and is characterized by linear weight uptake with respect to the number of deposition cycles and a constant bilayer thickness of 15 to 21 nm. Thin‐film electrical contact resistance is found to be proportional to the thickness after equilibration of the bilayer structure. Measured values range from 1.6 mΩ cm^?2 at 173 nm to 3.5 mΩ cm^?2 at 276 nm. Coating volume resistivity is reduced when electrostatic interactions are enhanced during LBL assembly.     

Role of Polymeric Metal Nucleation Inducers in Fabricating Large‐Area,Flexible, and Transparent Electrodes for Printable Electronics

The advent of special types of transparent electrodes, known as “ultrathin metal electrodes,” opens a new avenue for flexible and printable electronics based on their excellent optical transparency in the visible range while maintaining their intrinsic high electrical conductivity and mechanical flexibility. In this new electrode architecture, introducing metal nucleation inducers (MNIs) on flexible plastic substrates is a key concept to form high‐quality ultrathin metal films (thickness ≈ 10 nm) with smooth and continuous morphology. Herein, this paper explores the role of “polymeric” MNIs in fabricating ultrathin metal films by employing various polymers with different surface energies and functional groups. Moreover, a scalable approach is demonstrated using the ionic self‐assembly on typical plastic substrates, yielding large‐area electrodes (21 × 29.7 cm²) with high optical transmittance (>95%), low sheet resistance (<10 Ω sq^?1), and extreme mechanical flexibility. The results demonstrate that this new class of flexible and transparent electrodes enables the fabrication of efficient polymer light‐emitting diodes.     

Reduced Graphene Oxide Micromesh Electrodes for Large Area,Flexible, Organic Photovoltaic Devices

A laser‐based patterning technique—compatible with flexible, temperature‐sensitive substrates—for the production of large area reduced graphene oxide micromesh (rGOMM) electrodes is presented. The mesh patterning can be accurately controlled in order to significantly enhance the electrode transparency, with a subsequent slight increase in the sheet resistance, and therefore improve the tradeoff between transparency and conductivity of reduced graphene oxide (rGO) layers. In particular, rGO films with an initial transparency of ≈20% are patterned, resulting in rGOMMs films with a ≈59% transmittance and a sheet resistance of ≈565 Ω sq^?1, that is significantly lower than the resistance of ≈780 Ω sq^?1, exhibited by the pristine rGO films at the same transparency. As a proof‐of‐concept application, rGOMMs are used as the transparent electrodes in flexible organic photovoltaic (OPV) devices, achieving power conversion efficiency of 3.05%, the highest ever reported for flexible OPV devices incorporating solution‐processed graphene‐based electrodes. The controllable and highly reproducible laser‐induced patterning of rGO hold enormous promise for both rigid and flexible large‐scale organic electronic devices, eliminating the lag between graphene‐based and indium–tin oxide electrodes, while providing conductivity and transparency tunability for next generation flexible electronics.     

Atmospheric plasma deposition of transparent semiconducting ZnO films on plastics in ambient air

Transparent zinc oxide (ZnO) thin films have been successfully synthesized on poly (methyl methacrylate) (PMMA), polycarbonate (PC), and polyethylene terephthalate (PET) substrates by atmospheric plasma deposition in ambient air at room temperature. The structural, optical and electrical properties of the ZnO films as well as their adhesion to the polymer substrates were investigated for various deposition conditions. The film surface exhibited a dome-shaped topography comprised of nanometer-sized grains. The size of both the domes and the grains became larger as the plasma power increased. The visible transmittance increased above 95% with decreasing plasma power. The resistivity exhibited a wide variation in the range of 10²–10⁸ ohm cm. The adhesion energies to PMMA varied from 0.2 to 1.5 J/m² with increasing plasma power. While a finer grain structure achieved with lower plasma power was preferable for higher transmittance, it resulted in lower adhesion to the plastic substrates. The study demonstrated the feasibility of depositing semiconducting transparent ZnO films on polymer substrates at low temperature in ambient air using atmospheric plasma deposition.     

Bendable Solar Cells from Stable,Flexible, and Transparent Conducting Electrodes Fabricated Using a Nitrogen‐Doped Ultrathin Copper Film

Copper has attracted significant interests as an abundant and low‐cost alternative material for flexible transparent conducting electrodes (FTCEs). However, Cu‐based FTCEs still present unsolved technical issues, such as their inferior light transmittance and oxidation durability compared to conventional indium tin oxide (ITO) and silver metal electrodes. This study reports a novel technique for fabricating highly efficient FTCEs composed of a copper ultrathin film sandwiched between zinc oxides, with enhanced transparency and antioxidation performances. A completely continuous and smooth copper ultrathin film is fabricated by a simple room‐temperature reactive sputtering process involving controlled nitrogen doping (<1%) due to a dramatic improvement in the wettability of copper on zinc oxide surfaces. The electrode based on the nitrogen‐doped copper film exhibits an optimized average transmittance of 84% over a spectral range of 380 ?1000 nm and a sheet resistance lower than 20 Ω sq^?1, with no electrical degradation after exposure to strong oxidation conditions for 760 h. Remarkably, a flexible organic solar cell based on the present Cu‐based FTCE achieves a power conversion efficiency of 7.1%, clearly exceeding that (6.6%) of solar cells utilizing the conventional ITO film, and this excellent performance is maintained even in almost completely bent configurations.     

Production of Flexible Transparent Conducting Films of Self‐Fused Nanowires via One‐Step Supersonic Spraying

Scalable and economical manufacturing of flexible transparent conducting films (TCF) is a key barrier to widespread adoption of low‐cost flexible electronics. Here, a simple, robust, and scalable method of flexible TCF formation using supersonic kinetic spraying is demonstrated. Silver nanowire (AgNW) suspensions are sprayed at supersonic speed to produce self‐sintered films of AgNWs on flexible substrates. These films display remarkably low sheet resistance, <10 Ω sq^?1, combined with high transmittance, >90%. These electrically conducting, transparent, and flexible coatings can be deposited over a 100 cm² area in ≈30 s. Theoretical analysis reveals the underlying physical mechanism behind self‐sintering, showing that self‐sintering is enabled by the high velocity of impact in supersonic spraying.     

Reactive Ion Beams Sputtering of Vanadium Oxides Films for Uncooled Microbolometer

Vanadium oxides thin films for uncooled bolometric detectors have been fabricated on Si₃N₄-film-coated Si substrates by low temperature reactive ion beam sputtering in a controlled oxygen atmosphere. The typical growth temperature is kept at 200°C during sputtering, which is compatible with the post-CMOS technology. The as-deposited film exhibits sheet resistance and temperature coefficient resistant of 32 kΩ and ?0.025 K^?1 at room temperature, respectively.