基于模糊切换增益调节的燃气流量滑模控制

将模糊控制方法与滑模控制方法相结合,针对燃气流量调节伺服系统设计一种基于模糊切换增益调节的滑模控制器,固冲发动机流量调节伺服控制系统的不确定部分通过滑模控制器来补偿,从而可实现固冲发动机流量调节伺服系统的鲁棒控制。使用matlab对固冲发动机流量调节伺服系统进行建模仿真并与单纯使用滑模控制方法进行比较,仿真结果表明基于模糊切换增益调节的固冲发动机模糊滑模控制系统具有较好的给定适应性和抗干扰性,采用该控制方案能有效的抑制系统随机干扰对控制系统的不利影响,控制效果优于纯滑模控制方法,消弱了控制信号的抖振,为提高固冲发动机流量调节控制系统的动态性能奠定基础。     

改进的等效滑模控制器在异步电动机矢量控制系统中的应用

针对异步电动机矢量控制系统常规等效滑模控制存在扰动稳态误差大、抖振大、跟踪快速性差的问题,设计了一种改进的等效滑模控制器。该控制器采用改进的切换控制函数,提高了电动机的动态控制性能。仿真试验结果表明,与传统的PI控制器和常规的等效滑模控制器相比,该控制器能有效降低系统抖振,提高了系统的动态响应速度,增强了系统的鲁棒性。     

不确定Duffing混沌系统的同步控制

在模糊滑模变结构控制基础上,研究具有不确定性Duffing混沌系统的同步控制问题。选择合适的滑模面,基于Lyapunov稳定性理论设计模糊滑模变结构控制器及自适应更新规则,从理论上证明控制系统的稳定性。由于控制器的设计是基于自适应模糊滑模变结构控制的,与常规方法相比,控制器滑动模态不受干扰的影响,有较好的鲁棒性和快速跟踪能力。通过数值仿真实验验证了该系统的有效性。     

无刷直流电机的自适应模糊滑模控制策略研究

为了提高无刷直流电机（BLDCM,brushless dC motor）控制系统的动态响应速度和干扰抑制能力,提出了一种新的自适应模糊滑模控制（AFSMC,adaptive fuzzy sliding mode control）策略。控制系统根据滑模开关函数的取值范围,可以切换滑模控制器的输出,能够改进滑模观测器的抖振现象和系统稳定性。控制器的控制律由自适应模糊控制算法调节,滑模控制器的输出减少了系统不确定时延的影响。根据所提出控制策略建立了仿真模型,并进行了仿真。仿真结果表明,所提出的控制策略能提高系统的动态性能和鲁棒性。该方法用于无刷直流电机的控制是可行的、有效的。     

结晶器液位模糊控制系统的优化设计与仿真

结晶器液位控制系统中存在时变、滞后等非线性特性,使得它的控制变得特别复杂。针对常规PID控制和模糊控制所存在的问题,提出了一种优化模糊控制方案以提高系统的控制性能。首先分析了结晶器液位控制系统的结构和原理,介绍了模糊控制器的设计过程,最后利用MATLAB软件进行了仿真实验。结果表明,优化模糊控制的引入有效地克服了系统的扰动,提高了系统的控制性能。     

基于AFSMC算法的四旋翼飞行器控制策略研究

针对四旋翼飞行器在飞行过程中,控制系统存在非线性、强耦合、不确定性和鲁棒性差的问题,建立了关于四旋翼飞行器的动力学数学模型,将自适应控制、模糊控制和滑模控制相结合,提出基于自适应模糊滑模控制(AFSMC)的快速平稳控制策略。采用模糊系统推理方法实现理想控制律的逼近。在满足李雅普诺夫稳定性条件的前提下进行控制器的设计和稳定性分析,并结合四旋翼的数学模型和给定参数进行了MATLAB仿真。仿真结果表明,AFSMC控制器相比常规PID控制器具有良好的动态性能和抗干扰能力。     

基于遗传算法的模糊滑模控制

模糊控制和滑模控制的结合提供了非线性控制的一大新方法,它消除了滑模控制的抖动,但同时带来新的问题——静差,而且这种控制器在控制切换时动态性能与滑平面系数选择有很大关系.鉴于以上问题,该文提出用不均匀分布隶属函数的模糊控制器来代替传统滑模控制器的符号函数,同时为了保证模糊控制系统的全局稳定性,考虑加入模糊监督控制器.再基于遗传算法对滑平面系数和因子寻优,在算法中目标函数是系统的误差和表征系统稳定性的一个新变量.这种方法减小了系统的稳态误差,加快了系统到达滑动平面的速度,有效地消除了抖动.仿真结果表明了该方法的有效性.     

自适应模糊滑模控制及在轧机APC中的应用

基于模糊自适应控制方法设计了轧机厚控APC(Automatic Position Control)的滑模跟踪控制器,在系统动态函数未知的情况下,运用动态模糊逻辑系统DFLS(Dynamic Fuzzy Logic System)以及自适应机构构造变结构控制;应用李亚普诺夫方法设计滑模系数以及变结构控制律参数,使得闭环系统渐近稳定;不需要轧机APC的精确数学模型。仿真结果验证了控制系统的有效性以及抗干扰性能。     

基于模糊扰动观测器的PMSM积分滑模控制研究

为了克服传统永磁同步电机(Permanent magnet synchronous motor,PMSM)的滑模控制增益大容易产生抖振的问题,提出基于模糊观测器的PMSM积分滑模控制策略。采用新型趋近律设计积分滑模控制器取代传统的滑模控制器,提高系统的动态响应性能。结合模糊控制与自适应控制的特点,设计模糊扰动观测器,能够迅速有效地观测系统内部参数变化和外部扰动,并对积分滑模速度控制器进行前馈补偿,削弱系统抖振的同时提高了系统的鲁棒性。通过李雅普诺夫理论证明了该控制系统的稳定性。仿真及实验结果验证了该方法具有较强的鲁棒性,可以实现良好的跟踪效果并且无抖动。     

基于VB的模糊神经网络控制技术研究

本文将模糊逻辑推理与神经网络控制技术融合，设计了模糊神经网络控制器，仿真结果验证了控制器性能良好，并获取控制器的优化参数。基于VB技术创建了ACTTVEX控件，将该控件嵌入组态软件中进行双水槽液位控制系统的实时控制，结果表明控制及时，系统稳定性得到提高，具有广阔的推广应用前景。     

Only connect: teaching, technology and telesis

Abstract This paper describes an approach to the design of interactive multimedia materials being developed in a European Community project. The developmental process is seen as a dialogue between technologists and teachers. This dialogue is often problematic because of the differences in training, experience and culture between them. Conditions needed for fruitful dialogue are described and the generic model for learning design used in the project is explained.     

European Community policy and the market

Abstract This paper starts with some reflections on the policy considerations and priorities which are shaping European Commission (EC) research programmes. Then it attempts to position the current projects which seek to capitalise on information and communications technologies for learning in relation to these priorities and the apparent realities of the marketplace. It concludes that while there are grounds to be optimistic about the contribution EC programmes can make to the efficiency and standard of education and training, they are still too technology driven.     

一种自适应子融合集成多分类器方法

融合集成方法已经广泛应用在模式识别领域,然而一些基分类器实时性能稳定性较差,导致多分类器融合性能差,针对上述问题本文提出了一种新的基于多分类器的子融合集成分类器系统。该方法考虑在度量层融合层次之上通过对各类基多分类器进行动态选择,票数最多的类别作为融合系统中对特征向量识别的类别,构成一种新的自适应子融合集成分类器方法。实验表明,该方法比传统的分类器以及分类融合方法识别准确率明显更高,具有更好的鲁棒性。     

Avoiding semantic and temporal gaps in developing software intensive systems

Development of software intensive systems (systems) in practice involves a series of self-contained phases for the lifecycle of a system. Semantic and temporal gaps, which occur among phases and among developer disciplines within and across phases, hinder the ongoing development of a system because of the interdependencies among phases and among disciplines. Such gaps are magnified among systems that are developed at different times by different development teams, which may limit reuse of artifacts of systems development and interoperability among the systems. This article discusses such gaps and a systems development process for avoiding them.     

Designing economic np control charts: A programmed simulation approach

This paper presents control charts models and the necessary simulation software for the location of economic values of the control parameters. The simulation program is written in FORTRAN, requires only 10K of main storage, and can run on most mini and micro computers. Two models are presented - one describes the process when it is operating at full capacity and the other when the process is operating under capacity. The models allow the product quality to deteriorate to a further level before an existing out-of-control state is detected, and they can also be used in situations where no prior knowledge exists of the out-of-control causes and the resulting proportion defectives.     

The development of robot art

Going through a few examples of robot artists who are recognized worldwide, we try to analyze the deepest meaning of what is called “robot art” and the related art field definition. We also try to highlight its well-marked borders, such as kinetic sculptures, kinetic art, cyber art, and cyberpunk. A brief excursion into the importance of the context, the message, and its semiotics is also provided, case by case, together with a few hints on the history of this discipline in the light of an artistic perspective. Therefore, the aim of this article is to try to summarize the main characteristics that might classify robot art as a unique and innovative discipline, and to track down some of the principles by which a robotic artifact can or cannot be considered an art piece in terms of social, cultural, and strictly artistic interest. This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January 31–February 2, 2008     

Explanation and prediction: an architecture for default and abductive reasoning

Although there are many arguments that logic is an appropriate tool for artificial intelligence, there has been a perceived problem with the monotonicity of classical logic. This paper elaborates on the idea that reasoning should be viewed as theory formation where logic tells us the consequences of our assumptions. The two activities of predicting what is expected to be true and explaining observations are considered in a simple theory formation framework. Properties of each activity are discussed, along with a number of proposals as to what should be predicted or accepted as reasonable explanations. An architecture is proposed to combine explanation and prediction into one coherent framework. Algorithms used to implement the system as well as examples from a running implementation are given.     

Three Process Perspectives: Organizations, Teams, and People

This paper provides the author's personal views and perspectives on software process improvement. Starting with his first work on technology assessment in IBM over 20 years ago, Watts Humphrey describes the process improvement work he has been directly involved in. This includes the development of the early process assessment methods, the original design of the CMM, and the introduction of the Personal Software Process (PSP)^SM and Team Software Process (TSP){^SM}. In addition to describing the original motivation for this work, the author also reviews many of the problems he and his associates encountered and why they solved them the way they did. He also comments on the outstanding issues and likely directions for future work. Finally, this work has built on the experiences and contributions of many people. Mr. Humphrey only describes work that he was personally involved in and he names many of the key contributors. However, so many people have been involved in this work that a full list of the important participants would be impractical.     

基于复小波噪声方差显著修正的SAR图像去噪

提出了一种基于复小波域统计建模与噪声方差估计显著性修正相结合的合成孔径雷达(Synthetic Aperture Radar,SAR)图像斑点噪声滤波方法。该方法首先通过对数变换将乘性噪声模型转化为加性噪声模型,然后对变换后的图像进行双树复小波变换(Dualtree Complex Wavelet Transform,DCWT),并对复数小波系数的统计分布进行建模。在此先验分布的基础上,通过运用贝叶斯估计方法从含噪系数中恢复原始系数,达到滤除噪声的目的。实验结果表明该方法在去除噪声的同时保留了图像的细节信息,取得了很好的降噪效果。     

How do children do mathematics with LOGO?

Abstract  This paper considers some results of a study designed to investigate the kinds of mathematical activity undertaken by children (aged between 8 and 11) as they learned to program in LOGO. A model of learning modes is proposed, which attempts to describe the ways in which children used and acquired understanding of the programming/mathematical concepts involved. The remainder of the paper is concerned with discussing the validity and limitations of the model, and its implications for further research and curriculum development.