Wear mechanism of coated tools in the turning of ductile cast iron having wide range of tensile strength

In this study different specimens of ductile cast iron with tensile strength ranking from 400 MPa to 675 MPa were turned with K15 carbide, TiN coated and TiAlN coated tool in order to investigate wear mechanism and performance. Cutting forces and cutting temperature were similar for both coated tools, however flank wear and BUE were the lowest on the TiAlN coated tool, for this reason the TiAlN coated tool is suitable in the machining of ductile cast iron. The proposed tool wear mechanism is based on like-intermittent cutting caused by the pass from hard matrix to the soft graphite occasioning wear by adhesion. The analysis of the flank wear on coated tools is proposed by means of the wear curves in logarithmic scale instead of the usual linear scale. In this way, the change in wear rate is easily observed. This phenomenon was related with the wear out of the coating layer. The partial loss of the coating layer on cutting edge was confirmed by the EDS mapping images and SEM photographs.     

Cutting forces,tool wear and surface finish in high speed diamond machining

We have investigated the cutting forces, the tool wear and the surface finish obtained in high speed diamond turning and milling of OFHC copper, brass CuZn39Pb3, aluminum AlMg5, and electroless nickel. In face turning experiments with constant material removal rate the cutting forces were recorded as a function of cutting speed between v_c = 150 m/min and 4500 m/min revealing a transition to adiabatic shearing which is supported by FEM simulations of the cutting process. Fly-cutting experiments carried out at low (v_c = 380 m/min) and at high cutting speed (v_c = 3800 m/min) showed that the rate of abrasive wear of the cutting edge is significantly higher at ordinary cutting speed than at high cutting speed in contrast to the experience made in conventional machining. Furthermore, it was found that the rate of chemically induced tool wear in diamond milling of steel is decreasing with decreasing tool engagement time per revolution. High speed diamond machining may also yield an improved surface roughness which was confirmed by comparing the step heights at grain boundaries obtained in diamond milling of OFHC copper and brass CuZn39Pb3 at low (v_c = 100 m/min) and high cutting speed (v_c = 2000 m/min). Thus, high speed diamond machining offers several advantages, let alone a major reduction of machining time.     

An empirical survey on the influence of machining parameters on tool wear in diamond turning of large single-crystal silicon optics

We conducted a series of screening experiments to survey the influence of machining parameters on tool wear during ductile regime diamond turning of large single-crystal silicon optics. The machining parameters under investigation were depth-of-cut, feed rate, surface cutting speed, tool radius, tool rake angle and side rake angle, and cutting fluid. Using an experimental design technique, we selected twenty-two screening experiments. For each experiment we measured tool wear by tracing the tool edge with an air bearing linear variable differential transformer before and after cutting and recording the amount of tool edge recession. Using statistical tools, we determined the significance of each cutting parameter within the parameter space investigated. We found that track length, chip size, tool rake angle and surface cutting speed significantly affect tool wear, while cutting fluid and side rake angle do not significantly affect tool wear within the ranges tested. The track length, or machining distance, is the single most influential characteristic that causes tool wear. For a fixed part area, a decrease in track length corresponds to an increase in feed rate. Less tool wear occurred on experiments with negative rake angle tools, larger chip sizes and higher surface velocities. The next step in this research is to perform more experiments in this region to develop a predictive model that can be used to select cutting parameters that minimize tool wear.     

Cooling performance of micro-texture at the tool flank face under high pressure jet coolant assistance

Micro-texture at the tool face is a state-of-the-art technique to improve cutting performance. In this paper, five types of micro-texture were fabricated at the flank face to improve the cooling performance under the condition of high pressure jet coolant assistance. By using micro-textures consisted of pin fins, plate fins and pits fabricated 0.3 mm away from the cutting edge, heat transfer from the tool face to coolant was enhanced. The conditions of tool wear, adhesion and chip formation were compared between the micro-textured and non-patterned tools in the longitudinal turning of the nickel-based superalloy Inconel 718. As a result, micro-textured tools always exhibited the reduced flank and crater wear compared with the non-patterned tool, and the rate of tool wear was influenced by the array and height of fin. The energy dispersive spectroscopy analysis of worn flank faces and the electromotive forces obtained from the tool-work thermocouple supported better cooling performances of micro-textured tools. In addition, coolant deposition at flank face evidenced that heat transfer could be promoted by micro-texture near the border of the contact area between the flank wear land and machined surface. Finally, the changes of flow patterns with pit depth are analyzed for pit type tools by computational fluid dynamics. This investigation clearly showed the function of micro-textures for increasing the turbulent kinetic energy and cooling the textured tool face.     

Optimization of surface roughness,cutting force and tool wear of nitrogen alloyed duplex stainless steel in a dry turning process using Taguchi method

In this work, the dry turning parameters of two different grades of nitrogen alloyed duplex stainless steel are optimized by using Taguchi method. The turning operations were carried out with TiC and TiCN coated carbide cutting tool inserts. The experiments were conducted at three different cutting speeds (80, 100 and 120 m/min) with three different feed rates (0.04, 0.08 and 0.12 mm/rev) and a constant depth of cut (0.5 mm). The cutting parameters are optimized using signal to noise ratio and the analysis of variance. The effects of cutting speed and feed rate on surface roughness, cutting force and tool wear were analyzed. The results revealed that the feed rate is the more significant parameter influencing the surface roughness and cutting force. The cutting speed was identified as the more significant parameter influencing the tool wear. Tool wear was analyzed using scanning electron microscope image. The confirmation tests are carried out at optimum cutting conditions. The results at optimum cutting condition are predicted using estimated signal to noise ratio equation. The predicted results are found to be closer to experimental results within 8% deviations.     

Nanometric cutting in a scanning electron microscope

A nanometric cutting device under high vacuum conditions in a scanning electron microscope (SEM) was developed. The performance, tool-sample positioning, and processing capacity of the nanometric cutting platform were studied. The proposed device can be used to realize a displacement of 7 μm, with a closed-loop resolution of 0.6 nm in both the cutting direction and the depth direction. Using a diamond cutting tool with an edge radius of 43 nm formed by focused ion beam (FIB) processing, nanometric cutting experiments on monocrystalline silicon were performed on the developed cutting device under SEM online observation. Chips and machining results of different depths of cut were studied during the cutting process, and cutting depths of less than 10 nm could be obtained with high repeatability. Moreover, the cutting speed was found to exhibit a strong relationship with the brittle–ductile transition depth on brittle material. The experimental results of taper cutting and sinusoidal cutting indicated that the developed device has the ability to perform multiple degrees of freedom (DOFs) cutting and to study nanoscale material removal behaviour.     

Detection of chipping in ceramic cutting inserts from workpiece profile during turning using fast Fourier transform (FFT) and continuous wavelet transform (CWT)

Ceramic cutting tool inserts are prone to premature failure by chipping instead of gradual wear due to their low impact toughness. Thus, in-process detection of failure of ceramic tools is important to prevent workpiece surface deterioration. The objective of this study is to develop a method of detection of the onset of chipping in ceramic cutting tool inserts during dry finish turning from the workpiece profile signature. The profile of the workpiece surface opposite the cutting side was captured using an 18-MP DSLR camera at a shutter speed of 0.25 ms during the turning of AISI01 oil-hardening tool steel. The edge profile was extracted to sub-pixel accuracy from the 2-D image of the workpiece surface using the invariant moment method. The effect of chipping in the ceramic insert on the surface profile signature of the workpiece was investigated using the fast Fourier transform (FFT) and continuous wavelet transform (CWT). The results show that the stochastic behavior of the cutting process after tool chipping manifest as sharp increase in the amplitude of spatial frequencies below the fundamental feed frequency. The proposed sub-window FFT method is effective in resolving the time resolution by detecting tool chipping at cutting time duration of around 17.13 s. Compared to the sub-window FFT method the CWT method is able to detect the exact onset of chipping in the cutting tool insert.     

Knife-edge interferometry for cutting tool wear monitoring

This paper presents a novel technique for more easily measuring cutting tool wear using knife-edge interferometry (KEI). Unlike an amplitude splitting interferometry, such as Michelson interferometry, the proposed KEI utilizes interference of a transmitted wave and a diffracted wave at the cutting tool edge. In this study, a laser beam was incident on the cutting tool edge, and the photodetector was used to determine the interference fringes by scanning a cutting tool edge along the cutting direction. The relationship between the cutting tool wear and interferometric fringes generated by edge diffraction phenomena was established by using the cross-correlation of KEI fringes of two different cutting tool-edge conditions. The cutting tool wear produced the phase shift (attrition wear) and the decay of oscillation (abrasive wear) in the interferometric fringe. The wear characteristics of the cutting tool with a radius of curvature of 6 mm were investigated by measuring the interferometric fringes of the tool while cutting an aluminum work piece in a lathe. As a result, the attrition and abrasive wear of cutting tool showed a linear relationship of 5.62 lag/wear (μm) and 1.14E-3/wear (μm), respectively. This measurement technique can be used for directly inspecting the cutting tool wear in on-machine process at low-cost.     

Wear mechanisms of PcBN cutting tools when dry turning ASTM Grade 2 austempered ductile iron under finishing conditions

Experimental studies of dry finish turning of ASTM Grade 2 austempered ductile iron with PcBN cutting tools were carried out at cutting speeds ranging from 50 to 800 m/min, at a feed of 0.05 mm/rev and depth cut of 0.2 mm. The wear mechanisms of PcBN cutting tools were investigated through the examination of the wear surfaces by means of optical, scanning electron and transmission electron microscopes as well as energy dispersive spectroscopy. Flank wear and crater wear were the main wear modes within this range of cutting speeds. Adhesion and adhesion induced abrasion were the main wear mechanisms at cutting speeds less than 150 m/min. Abrasion and wear by thermally activated-diffusion and oxidation-chemical reaction wear were the main wear mechanisms at cutting speeds greater than 150 m/min. A high concentration of Mg, Si, and O on the wear surfaces and a heat-affected zone in the tools suggested that at speeds in excess of 150 m/min, the rate controlling wear mechanism involved chemical reaction between the tools and the operating environment.     

Wear mechanisms of WC coated and uncoated tools in finish turning of Inconel 718

This paper presents the results of an experimental investigation on the wear mechanisms of uncoated tungsten carbide (WC) and coated tools (single-layer (TiAlN) PVD, and triple-layer (TiCN/Al₂O₃/TiN) CVD) in oblique finish turning of Inconel 718. Tool wear rate and wear mechanisms were evaluated for cutting speeds, 50<V<100 m/min, and feed rates, 0.075<f<0.125 mm/rev, at a constant depth of cut of 0.25 mm. It was concluded that abrasive and adhesive wear were the most dominant wear mechanisms, controlling the deterioration and final failure of the WC tools. While the triple layer CVD coated tools exhibited the highest wear resistance at high cutting speeds and low feeds, uncoated tools outperformed the single and multi-layer coated tools in the low range of cutting speeds and intermediate feeds. The cutting tool with single-layer PVD coating outperformed the other tools at the medium cutting speed.     

Cutting performance of nano-crystalline diamond (NCD) coating in micro-milling of Ti6Al4V alloy

Hard coatings are an important factor affecting the cutting performance of tools. In particular, they directly affect tool life, cutting forces, surface quality and burr formation in the micro-milling process. In this study, the performance of nano-crystalline diamond (NCD) coated tools was evaluated by comparing it with TiN-coated, AlCrN-coated and uncoated carbide tools in micro-milling of Ti₆Al₄V alloy. A series of micro-milling tests was carried out to determine the effects of coating type and machining conditions on tool wear, cutting force, surface roughness and burr size. Flat end-mill tools with two flutes and a diameter of 0.5 mm were used in the micro-milling process. The minimum chip thickness depending on both the cutting force and the surface roughness were determined. The results showed that the minimum chip thickness is about 0.3 times that of the cutter corner radius for Ti₆Al₄V alloy and changes very little with coating type. It was observed from wear tests that the dominant wear mechanism was abrasion. Maximum wear occurred on NCD-coated and uncoated tools. In addition, maximum burr size was obtained in the cutting process with the uncoated tool.     

Design and experimental results of a tunable vibration turning device operating at ultrasonic frequencies

The development of a tunable ultrasonic vibration-assisted diamond-turning tool is described. The resonance operation method, which formerly served to achieve mechanical motion at ultrasonic frequencies, is now replaced by a newly developed pulse driving technique. The prototype tools allow for vibration frequencies from dc up to 40 kHz and vibration amplitudes from 0 to 10 μm. This paper reviews the design of the new tool system and summarizes the experimental results from diamond turning steel work materials. As in other studies on vibration-assisted machining, the results show that the surface turned with a vibrating tool contains scalloped geometric features superimposed on the tool marks left from conventional turning, resulting in a lower total surface roughness. Tool wear comparisons document advantages from the added vibration, and variations in the carbon content in the resulting chips were also examined.     

Design and testing of a long-range,precision fast tool servo system for diamond turning

A long-range, precision fast tool servo (FTS) system was developed that is capable of accurately translating the cutting tool on a diamond turning machine (DTM) with maximum accelerations of 260 m s^?2 and bandwidths of up to 140 Hz. The maximum displacement range of the cutting tool is 2 mm. The FTS utilizes a flexure mechanism driven by a voice coil actuator, a custom linear current amplifier and a laser interferometer feedback system. This paper describes the design of the electromechanical system, controller configuration and cutting tests to evaluate the system. Initially, low disturbance rejection and poor command following degraded the surface finish of machined test parts. Several techniques to add damping to the dynamic system were investigated to improve the generated surface finishes. Electromotive damping was applied inside the voice coil actuator, and two different viscoelastic damping materials were applied to the flexure mechanism. A control strategy consisting of linear and non-linear feedforward controllers and a proportional, integral and derivative (PID) feedback controller was implemented to accommodate the changed system dynamics. The workpieces were analyzed using form and surface inspection instruments to evaluate the overall system performance. A cylindrical part with five lobes cut across the face had a surface finish value between 20 and 30 nm R_a.     

Hard turning using HiPIMS-coated carbide tools: Wear behavior under dry and minimum quantity lubrication (MQL)

In the present work, experimental investigations carried out to assess the applicability of HiPIMS (High Power Impulse Magnetron Sputtering)-coated carbide tools to hard turning (55 HRC) and to address the widely debated topic about the use of coolants in hard turning are presented. Tool wear progressions and hence, tool life, different tool wear forms and wear mechanisms observed for tools coated with HiPIMS coating technique, namely, nanocomposite AlTiN, nanocomposite multi-layer TiAlN/TiSiN and nanocrystalline AlTiCrN are presented along with the images captured by digital and electron microscope. Characterization results of all the coated tools in terms of their average coating thickness (measured using Calotest and Fractographs), adhesion strength of the coating(s) (determined using Scratch test), composition and microhardness (using EDAX and Vickers microhardness test, respectively) are presented. Experimental observations indicate higher tool life with nanocrystalline AlTiCrN coated carbide tools which shows encouraging potential of these tools to hard turning. Improvement in tool life of almost 20–25% has been observed under minimum quantity lubrication (MQL) due to better cooling and lubricating effects. However, this effect was more prominent at higher cutting speed of 150 m/min.     

Tool Wear in Ultra-Precision Diamond Cutting of Non-Ferrous Metals with a Round-Nose Tool

Tool wear causes the loss of the original profile accuracy of the cutting edge and degrades the form accuracy of machined surfaces. The purpose of this research is to clarify the tool-wear mechanism and its effect on machining accuracy in ultra-precision diamond cutting with a round-nose tool. Controlled cutting tests of Al 6061 were performed on a two-axis, ultra-precision turning machine. Single-crystal diamond tools were used in the experiment. The tool-wear pattern was studied based on the observation of the wear zone using a scanning electron microscope. The topographic characteristics of the chips were examined and the effect of the micro-cutting geometry on the tool wear was investigated theoretically and experimentally. The mutual effects of crystallographic dependence of wear resistance of diamonds and the change in the cutting velocity during machining are believed to be the main reasons causing uneven wear along the cutting edge. Measures for reducing the effect of tool wear are also discussed.     

Suppression of notch wear of a whisker reinforced ceramic tool in air-jet-assisted high-speed machining of Inconel 718

This paper describes the notch and flank wear specific to a SiC whisker reinforced alumina tool in air jet assisted (AJA) turning of nickel-base superalloy Inconel 718 at high cutting speeds. An AJA machining experiment has revealed that the air jet applied to the tool tip in addition to coolant dramatically reduces the depth-of-cut notch wear. As a result, the width of flank wear, but not the size of notch wear, determined the life of a ceramic tool in AJA machining of Inconel 718. This is a reason for the large extension and small variation of the tool life when high speed AJA machining is adopted. The maximum tool life length reached 2160 m at a cutting speed of 660 m/min under the given cutting conditions. Finally, the mechanisms of the notch and flank wear of a SiC whisker reinforced alumina tool in AJA machining are discussed from the viewpoints of tribochemical reactions and tool wear anisotropy.     

An experimental study of cutting performance on monocrystalline germanium after ion implantation

Monocrystalline materials, such as silicon and germanium, are widely used in the semiconductor industry and optical engineering due to their excellent electrical and optical characteristics. However, it is difficult to achieve an ultraprecise mirrored surface with the turning process due to the hard and brittle nature of those materials. It has been proved that the machinability of silicon and silicon carbide can be enhanced in nanometric or ultra-precise diamond cutting by ion implantation. In this paper, we present diamond cutting of monocrystalline germanium implanted with copper ions and study the brittle–ductile transition phenomenon. Raman spectra and transmission electron microscopy are used to investigate details of the modified layer. The results show that a uniform amorphous layer is produced after implantation. The brittle–ductile transition depth of the modified germanium is up to 730 nm, which is an obvious increase from unmodified c-Ge.     

The design and optimization of micro polycrystalline diamond ball end mill for repairing micro-defects on the surface of KDP crystal

Micro-milling is a promising approach to repair the micro-defects on the surface of KH₂PO₄ (KDP) crystal. The geometrical parameters of micro ball end mill will greatly influence the repairing process as a result of the soft brittle properties of KDP crystal. Two types of double-edged micro ball end mills were designed and a three-dimensional finite element (FE) model was established to simulate the micro milling process of KDP crystal, which was validated by the milling experiments. The rake angle of −45°, the relief angle of 45° and the cutting edge radius of 1.5–2 μm were suggested to be the optimal geometrical parameters, whereas the rake angle of −25° and the relief angle of 9° were optimal just for micro ball end mill of Type I, the configuration with the rake angles ranging from 0° to 35°, by fully considering the cutting force, and the stress–strain distribution over the entire tool and the cutting zone in the simulation. Moreover, the micro polycrystalline diamond (PCD) ball end mills adopting the obtained optimal parameters were fabricated by wire electro-discharge machining (WEDM) and grinding techniques, with the average surface roughness Ra of tool rake face and tool flank face ∼0.10 μm, and the cutting edge radius of the tool ∼1.6 μm. The influence of tool's geometrical parameters on the finished surface quality was verified by the cutting experiments, and the tool with symmetric structure was found to have a better cutting performance. The repairing outlines with Ra of 31.3 nm were processed by the self-fabricated tool, which could successfully hold the growth of unstable damage sites on KDP crystal.     

Development of a novel cubic boron nitride cutting tool with a textured flank face for high-speed machining of Inconel 718

Nickel-based superalloys such as Inconel 718 offer several advantages, including high-temperature strength and high corrosion resistance; this has led to a rapid increase in the demand for such materials, particularly in the aircraft industry. In contrast, these alloys are known to be among the most difficult-to-cut materials because of their mechanical and chemical properties, and tools used for this purpose have extremely short lifetimes. Recently, cubic boron nitride (CBN), which is the second hardest of all known materials, has received significant attention as a material for cutting tools and has already established itself in many fields of application. However, the performance of CBN tools is still insufficient for practical use, especially in the high-speed machining of Inconel 718. To overcome this problem, we first conducted orthogonal cutting experiments on Inconel 718 and performed cross-sectional observations of the CBN cutting tool in order to identify its wear mechanisms in continuous cutting operations under high-speed machining conditions (300 m/min). As a result, it was found that fatal tool failure occurs through crater and flank wear because of diffusion led by high cutting temperatures and subsequent chip adhesion to the tool flank face, accompanied by cutting edge chipping. Based on these results, a CBN cutting tool with a textured flank face was newly developed to improve the cutting tool life. Experimental: results showed that micro grooves generated on the flank face significantly suppressed the cutting edge chipping and remarkably extended the lifetime of the CBN tool during high-speed machining of Inconel 718.     

Investigating the Machinability of Al–Si–Cu cast alloy containing bismuth and antimony using coated carbide insert

Surface roughness and cutting force are two key measures that describe machined surface integrity and power requirement evaluation, respectively. This investigation presents the effect of melt treatment with addition of bismuth and antimony on machinability when turning Al–11%Si–2%Cu alloy. The experiments are carried out under oblique dry cutting conditions using a PVD TIN-coated insert at three cutting speeds of 70, 130 and 250 m/min, feed rates of 0.05, 0.1, 0.15 mm/rev, and 0.05 mm constant depth of cut. It was found that the Bi-containing workpiece possess the best surface roughness value and lowest cutting force due to formation of pure Bi which plays an important role as a lubricant in turning process, while Sb-containing workpiece produced the highest cutting force and highest surface roughness value. Additionally, change of silicon morphology from flake-like to lamellar structure changed value of cutting force and surface roughness during turning.