Characterization and tribological investigation of sol–gel ceramic films on Ti–6Al–4V

SiO₂, TiO₂, and hydroxyapatite (HA) thin films with good biocompatibility were grown on Ti–6Al–4V (coded as TC4) substrate by sol–gel and dip-coating processes from specially formulated sols, followed by annealing at 500 °C The chemical states of some typical elements in the target films were detected by means of X-ray photoelectron spectroscopy (XPS). Atomic force microscopy (AFM) and high-resolution scanning electron microscopy (SEM) are applied to characterize the original unworn films. The tribological properties of thin films sliding against an AISI52100 steel ball were evaluated on a reciprocating friction and wear tester. As the result, the target films composed of nano-particles ranging from 30 nm to 100 nm around were obtained. All the sol–gel ceramic films are superior in resisting wear compared with the TC4 substrate. Among all, HA film shows the best resistance while SiO₂ film shows the worst wear resistance both under higher (3 N) and lower load (1 N). TiO₂ shows good wear resistance under lower load (1 N). SEM observation of the morphologies of worn surfaces indicates that the wear of TC4 is characteristic of abrasive wear. Differently, abrasion, plastic deformation and micro-fracture dominate the wear of ceramic films. The superior friction reduction and wear resistance of HA film is greatly due to the slight plastic deformation of the film. It is supposed that the deformation of the HA film is closely related to the special arrangement of the nano-particles and microstructure. HA film is recommended for clinical application from the point of wear resistance view.     

Plastic deformation of 25CrMo4 steel during wear: Effect of the temperature,the normal force,the sliding velocity and the structural state

This article follows a previous study on friction and wear of 25CrMo4 steel [N. Khanafi-Benghalem, K. Loucif, E. Felder, F. Delamare, Influence de la température sur les mécanismes de frottement et d’usure des aciers X12NiCrMoSi25-20 et 25CrMo4 glissant sur du carbure de tungstène, Matériaux et techniques 93 (2005) 347–362]. The aim of our work is to study in more details the process of plastic deformation and the wear rate of this steel in lubricated sliding against cemented tungsten carbide, process observed in the previous work. The considered parameters are the temperature T (from 20 to 200 °C), the normal force P (from 500 to 1500 N), the steel structure (normalised HV 220 and quenched/tempered HV 480 states) and the sliding velocity v (from 0.05 to 0.3 m/s). We measured the friction coefficient and the sample total volume loss. A displacement sensor follows the volume loss evolution during the test; this follow-up is approximate because of the sample plastic flow which leads to the formation of peripheral burrs. All the tests conditions generate a significant plastic deformation of the sample steel, even in the quenched/tempered state: it produces a marked increase of the surface hardness, the work hardened layer being much finer for the quenched/tempered state (15 μm) than for the normalised state (40 μm at 20 °C). For temperatures T ≤ 100 °C in normalised state, the wear follows the Archard's law with an increasing rate with temperature. For T ≥ 120 °C, the wear rate decreases during the test, the global volume of wear being a decreasing function of T. For the quenched/tempered state, the wear rate decreases with the increase of the normal force, this decrease is less than 30% of the normalised state value. The material heating during the wear tests is well correlated with the friction dissipated power, but remains small, except in extreme cases (v maximum, great friction at high temperatures). These results suggest the existence of two wear mechanisms: abrasion by sample debris and burrs emission by plastic flow. The abrasion is probably the dominating mechanism for the tests carried out at the lowest temperatures. The plastic flow becomes a significant component at the highest temperatures. Using a contact model, we discuss to what extent the influence of the temperature and the strain rate on the steel hardness and ductility could explain the temperature and the sliding velocity effect on wear. Other phenomena are probably present: the influence of the steel microstructure and the lubricant on the size and/or the number of particles responsible for abrasion.     

Improved wear resistance in alumina-PTFE nanocomposites with irregular shaped nanoparticles

Past studies with PTFE nanocomposites showed up to 600× improvements in wear resistance over unfilled PTFE with the addition of Al₂O₃ nanoparticles. Irregular shaped nanoparticles are used in this study to increase the mechanical entanglement of PTFE fibrils with the filler. The tribological properties of 1, 2, 5 and 10 wt.% filled samples are evaluated under a normal pressure and sliding speed of 6.3 MPa and 50.8 mm/s, respectively. The wear resistance was found to improve 3000× over unfilled PTFE with the addition of 1 wt.% nanoparticles. The 5 wt.% sample had the lowest steady state wear rate of K = 1.3 × 10⁻⁷ mm³/N m and the lowest steady friction coefficient with μ = 0.21.     

WC–ZrO2 composites: processing and unlubricated tribological properties

In the present work, we report the processing and properties of WC–6 wt.% ZrO₂ composites, densified using the pressureless sintering route. The densification of the WC–ZrO₂ composites was carried out in the temperature range of 1500–1700 °C with varying time (1–3 h) in vacuum. The experimental results indicate that significantly high hardness of 22–23 GPa and moderate fracture toughness of ∼5 MPa m^1/2 can be obtained with 2 mol% Y-stabilized ZrO₂ sinter-additive, sintered at 1600 °C for 3 h. Furthermore, the friction and wear behavior of optimized WC–ZrO₂ composite is investigated on a fretting mode I wear tester. The tribological results reveal that a moderate coefficient of friction in the range from 0.15 to 0.5 can be achieved with the optimised composite. An important observation is that a transition in friction and wear with load is noted. The dominant mechanisms of material removal appear to be tribochemical wear and spalling of tribolayer.     

Tribological behaviors of Ti–6Al–4V modified by chemical methods

In order to improve the tribological properties of titanium-based implants, sodium hydroxide (NaOH), hydrogen peroxide (H₂O₂) solutions, sol–gel hydroxyapatite (HA) film, thermal treatment and combined methods of NaOH solution/HA film, H₂O₂ solution/HA film are used to modify the surfaces of Ti–6Al–4V (coded TC4). The chemical states of some typical elements in the modified surfaces were detected by means of X-ray photoelectron spectroscopy (XPS). The tribological properties of modified surfaces sliding against an AISI52100 steel ball were evaluated on a reciprocating friction and wear tester. As the results, complex surfaces with varied components are obtained. All the methods are effective in improving the wear resistance of Ti–6Al–4V in different degrees. Among all, the surface modified by the combined method of NaOH solution/HA film gives the best tribological performances. The friction coefficient is also greatly reduced by the modification of NaOH solution. The order of the wear resistance under 3 N is as following: Ti–NaOH–HA>Ti–NaOH>Ti–HA>Ti–H₂O₂–HA>Ti–H₂O₂ >Ti–500; under 1 N is Ti–HA, Ti–NaOH–HA>Ti–NaOH. For Ti–H₂O₂, a very low friction coefficient and long wear life over 2000 passes is obtained under 1 N. SEM observation of the morphologies of worn surfaces indicates that the wear of TC4 is characteristic of abrasive wear. Differently, abrasion, plastic deformation and micro–crack dominate the wear of Ti–HA; slight abrasive wear dominate the wear mechanism of Ti–NaOH and microfracture and abrasive wear for Ti–NaOH–HA and Ti–H₂O₂–HA, while the sample modified by thermal treatment is characterized by sever fracture. The superior friction reduction and wear resistance of HA films are greatly attributed to the slight plastic deformation of the film. NaOH solution is superior in improving the wear resistance and decreasing the friction coefficient under relative higher load (3 N) and H₂O₂ is helpful to reduce friction and wear under relatively lower load (1 N). Combined method of Ti–NaOH–HA is suggested to improve the wear resistance of Ti–6Al–4V for medial applications under fretting situations.     

Friction and wear properties of αFeSi2–Si alloy,ReSi1.8 and MoSi2 in ethyl alcohol

In this study, Fe–X at% Si alloy (X=70.5, 80.0 and 96.0), Re–64.3 at% Si and Mo–66.7 at% Si disk specimens were prepared by spark plasma sintering, and their friction and wear properties were investigated when they were slid against Si₃N₄ ball specimens in ethyl alcohol. The friction and wear properties of Si ingots were also examined. Fe–70.5 at% Si, Fe–80.0 at% Si, Fe–96.0 at% Si and Re–64.3 at% Si disk specimens exhibited friction coefficients as low as 0.15. It is considered that the low friction of the Fe–70.5 at% Si, Fe–80.5 at% Si and Fe–96.0 at% Si disk specimens was due to the formation of low friction silicon alkoxide and polyoxysilane on the worn surfaces of the disk specimens and the paired ball specimens. Re–64.3 at% Si disk specimens exhibited the highest microvickers hardness of all the disk specimens prepared in this study. In addition, the microvickers hardness of the Fe–X at% Si (X=70.5, 80.0, 96.0 and 100) disk specimen increased with increasing the Si content. Moreover, it was difficult to obtain dense Fe–90.0 at% Si disk specimens by sintering the annealed and crushed Fe–90.0 at% Si powder. However, dense Fe–96.0 at% Si disk specimens could be obtained by sintering the Fe–90.0 at% Si powder at 1403 K.     

Friction and wear behaviors of C/C-SiC composites containing Ti3SiC2

In the present paper, friction and wear behaviors of a carbon fiber reinforced carbon–silicon carbide–titanium silicon carbide (C-SiC–Ti₃SiC₂) hybrid matrix composites fabricated by slurry infiltration and liquid silicon infiltration were studied for potential application as brake materials. The properties were compared with those of C/C-SiC composites. The composites containing Ti₃SiC₂ had not only higher friction stability coefficient but also much higher wear resistance than C/C-SiC composites. At an initial braking speed of 28 m/s under 0.8 MPa pressure, the weight wear rate of the composites containing 5 vol% Ti₃SiC₂ was 5.55 mg/cycle, which was only one-third of C/C-SiC composites. Self-lubricious film-like debris was formed on the composites containing Ti₃SiC₂, leading to the improvement of friction and wear properties. The effect of braking speed and braking pressure on the tribological properties of modified composites were investigated. The average friction coefficient was significantly affected by braking speed and braking pressure, but the wear rate was less affected by braking pressure.     

Wear and friction behavior of Al6061 alloy reinforced with carbon nanotubes

Friction and wear behavior of Al6061 monolithic alloy and 1 wt% CNTs reinforced Al6061 composite prepared through ball milling and spark plasma sintering was investigated. It was found that, under mild wear conditions, the composite displayed lower wear rate and friction coefficient compared to the monolithic alloy. However, for severe wear conditions, the composite displayed higher wear rate and friction coefficient compared to the monolithic alloy. Analysis of worn surfaces revealed that, at lower loads, abrasion was the dominant wear mechanism for both materials. At higher loads, adhesion was found to be dominant for the monolithic alloy while excessive sub-surface fracturing and delamination were mainly observed for the composite. Also, it was clarified that the friction and wear behavior of Al–CNT composites is largely influenced by the applied load and there exists a critical load beyond which CNTs could have a negative impact on the wear resistance of aluminum alloy.     

Effect of three nitriding treatments on tribological performance of 42CrAlMo7 steel in boundary lubrication

Evolution of friction and wear of 42CrAlMo7 steels with different nitriding processes was investigated during boundary-lubricated rolling–sliding tests. The wear behaviour of nitrided steel with a thin compound layer (produced by plasma nitriding and by gas nitriding followed by oxidation) was characterised by the early removal of the compound layer, and the wear resistance was thus, given by the underlying diffusion layer. In the case of the material with a thick compound layer (produced by gas nitriding) wear was restricted to the compound layer. In this material, at low applied load (300 N, i.e. 485 MPa of Hertzian pressure, in this work), after the removal of the external porous layer wear tended to be negligible. At high applied load (1000 N, 890 MPa), on the other hand, the wear rate became higher than that of the diffusion layer. The friction behaviour was followed by determining the λ-factor evolution during each test. For a given λ-factor, the friction coefficients at 300 N were lower than at 1000 N.     

Study of TiAlSiN coatings post-treated with N and C + N ion implantations. Part 2: The tribological analysis

Ion implantation has found to be an effective approach to modify surface properties of materials. The present research investigates the effect of (1) nitrogen (N), and (2) carbon subsequently with nitrogen (C + N) implantations on the mechanical and tribological properties of the titanium–aluminium–silicon–nitride (Ti–Al–Si–N) coatings. Superhard TiAlSiN coatings produced by magnetron sputtering, of approximately 2.5 μm thickness, were post-treated by implantations of N or C + N at an energy level of 50 keV. The dose range was between 5 × 10¹⁶ and 1 × 10¹⁸ ions cm^?2. After implantation, the tribological performance of the coatings was investigated by a ball-on-disk tribometer against WC–6 wt.%Co ball under dry condition in ambient air. The wear performance of the samples was examined by a variety of characterization techniques, such as secondary electron microscopy (SEM), 3D profilometry, atomic force microscopy (AFM), and micro-Raman. The results showed that the wear performance of the samples depended strongly on the implanted elements and doses. There was slight improvement on the samples implanted with N whereas significant improvement was found on the C + N implantations. Particularly, the friction coefficient of the sample with 5 × 10¹⁷ C⁺ cm^?2 and 5 × 10¹⁷ N⁺ cm^?2 could reach 0.1. In addition, the specific wear rate of the sample was extremely low (0.85 × 10^?7 mm³/Nm), which was nearly two orders of magnitude below that of the un-implanted coating. The speculation of the mechanical and tribological analyses of the samples indicates that the improvement of the N implanted and C + N implanted TiAlSiN samples could be due to a combined effect of improved hardness, plus enhanced adhesive and cohesive strength. In addition, the improved performance of the C + N implanted samples could be explained by the formation of lubricating implanted-layer, which existed mostly in sp² C–C and C–N forms. The formation of such implanted layer could lead to a change of wear mode from strong abrasive wear to mostly adhesive wear, and result in a drop of friction coefficient and wear rate.     

Tribology characteristics of magnesium alloy AZ31B and its composites

In this paper, wear characteristics of magnesium alloy, AZ31B, and its nano-composites, AZ31B/nano-Al₂O_3, processed by the disintegrated melt deposition technique are investigated. The experiments were carried out using a pin-on-disk configuration against a steel disk counterface under different sliding speeds of 1, 3, 5, 7 and 10 m/s for 10 N normal load, and 1, 3 and 5 m/s for 30 N normal load. The worn samples and wear debris were then examined under a field emission scanning electron microscopy equipped with an energy dispersive spectrometer to reveal its wear features. The wear test results show that the wear rates of the composites are gradually reduced over the sliding speed range for both normal loads. The composite wear rates are higher than that of the alloy at low speeds and lower when sliding speed further increased. The coefficient of friction results of both the alloy and composites are in the range of 0.25–0.45 and reaches minimums at 5 m/s under 10 N and 3 m/s under 30 N load. Microstructural characterization results established different dominant mechanisms at different sliding speeds, namely, abrasion, delamination, oxidation, adhesion and thermal softening and melting. An experimental wear map was then constructed.     

Evolution of wear,roughness, and friction of Alloy 600 superalloy surfaces in water-submersed sliding

Self-mated wear and friction of Alloy 600 superalloy was studied in a water-submersed ring-on-rod configuration, loading the side of a 6.35 mm diameter rod across the flat surface of a rotating annular ring of 100 mm outer diameter and 70 mm inner diameter producing two sliding contacts along the ring. Tests were conducted at sliding speeds of 0.178 and 0.330 m/s for sliding distances of 100 m. Normal loads of 51 and 204 N were applied, and initial R_a surface roughnesses of the rings along the sliding direction were either smooth (～0.2 μm) or rough (～7.5 μm). Increased initial ring roughness caused a ～20-fold increase in rod wear at the lighter load, whereas at the heavier load increased initial roughness only caused a ～4-fold increase in wear. At lower initial ring roughness the 4-fold decrease in normal load caused a large (one order-of-magnitude) decrease in rod wear, whereas for rings of higher initial roughness the 4-fold decrease in normal load caused only minor (2-fold or less) decreases in rod wear. Wear during this 100 m sliding distance only experienced a minor effect from the 1.8-fold change in sliding speed, as did friction. In all cases friction coefficient rapidly settled into the range 0.6–0.7, except in the cases of lower load on rings of lower initial roughness where friction coefficient remained above 1 for most of this sliding duration. At this lower load the initial ～0.2 μm rod roughnesses increased to nearly 0.8 μm by the 100 m sliding distance, whereas at the higher load this same sliding distance resulted in roughnesses returning near to the initial 0.2 μm. It was hypothesized more highly loaded cases also went through initial roughening prior to smoothening back to 0.2 μm roughness within the 100 m sliding distance, and given additional sliding the more lightly loaded cases would also experience subsequent smoothening. Increasing sliding distance to 400 m, roughnesses indicated a smoothening back to 0.2 μm level during those lightly loaded tests, with friction coefficient correspondingly dropping from 1 into the 0.6–0.7 range observed in all other cases. Extended sliding to 400 m at light loading against rings of lower initial roughness also allowed a rod wear rate which increased with increased sliding distance to be observed, approaching the same rate observed against initially rough rings within the 100 m sliding distance.     

Effect of electrical current on tribological behavior of copper-impregnated metallized carbon against a Cu–Cr–Zr alloy

A block-on-slip ring-type wear tester was used to investigate the tribological behavior of copper-impregnated metallized carbon against a Cu–Cr–Zr alloy under 2 to 6 N applied load and 0 to 20 A electrical current. The sliding speed was maintained at 25 km/h. The wear loss of copper-impregnated metallized carbon increased with greater electrical current. Under a certain applied load, the wear loss with electrical current was minimized. The tribo-layer had an apparent effect on the friction coefficient. The wear mechanisms were complex, consisting of adhesive wear, abrasive wear and arc erosion.     

Effect of SiC particles on the friction and wear behavior of Ti3Si(Al)C2-based composites

The non-lubricated, sliding friction and wear behavior of Ti₃Si(Al)C₂ and SiC-reinforced Ti₃Si(Al)C₂ composites against AISI 52100 bearing steel ball were investigated using a ball-on-flat, reciprocating tribometer at room temperature. The contact load was varied from 5 to 20 N. For monolithic Ti₃Si(Al)C₂, high friction coefficients between 0.61 and 0.90 and wear rates between 1.79 × 10⁻³ and 2.68 × 10⁻³ mm³ (N m)⁻¹ were measured. With increasing SiC content in the composites, both the friction coefficients and the wear rates were significantly decreased. The friction coefficients reduced to a value between 0.38 and 0.50, and the wear rates to between 2.64 × 10⁻⁴ and 1.93 × 10⁻⁵ mm³ (N m)⁻¹ when the SiC content ranged from 10 to 30 vol.%. The enhanced wear resistance of Ti₃Si(Al)C₂ is mainly attributed to the facts that the hard SiC particles inhibit the plastic deformation and fracture of the soft matrix, the oxide debris lubricate the counterpair, and the wear mode converts from adhesive wear to abrasive wear during dry sliding.     

Surface finishing: Impact on tribological characteristics of WC–Co hardmetals

Flat samples of WC–Co hardmetals with 6–12 wt%Co were surface finished by grinding, polishing and wire-electro-discharge machining (EDM). Comparative dry reciprocating sliding experiments against WC–6 wt%Co pins were performed using a Plint TE77 tribometer. Tribological characteristics were recorded online. Wear surfaces were characterized by surface scanning topography and scanning electron microscopy. Wire-EDM’ed samples exhibited higher friction and wear compared to ground and polished equivalents. This trend was correlated to X-ray diffraction measurements revealing tensile residual surface stresses in WC after wire-EDM contrary to compressive surface stresses after grinding and polishing. However, finer executed EDM reduces friction and wear significantly.     

Mechanical and unlubricated tribological properties of titanium-containing diamond-like carbon coatings

Titanium-containing diamond-like carbon (Ti-DLC) coatings were deposited on steel with a close-field unbalanced magnetron sputtering in a mixed argon/acetylene atmosphere. The morphology and structure of Ti-DLC coatings were investigated by scanning electron microscopy, transmission electron microscopy, atomic force microscopy and Raman spectroscopy. Nanoindentation, nanoscratch and unlubricated wear tests were carried out to evaluate the hardness, adhesive and tribological properties of Ti-DLC coatings. Electron microscopic observations demonstrated the presence of titanium-rich nanoscale regions surrounded by amorphous carbon structures in Ti-DLC coating. The Ti-DLC coatings exhibit friction coefficients of 0.12–0.25 and wear rates of 1.82 × 10^?9 to 4.29 × 10^?8 mm³/Nm, depending on the counterfaces, sliding speed and temperature. The Ti-DLC/alumina tribo-pair shows a lower friction coefficient than the Ti-DLC/steel tribo-pair under the identical wear conditions. Increasing the test temperature from room temperature to 200 °C reduces the coefficient of friction and, however, clearly increases the wear rate of Ti-DLC coatings. Different wear mechanisms, such as surface polishing, delamination and tribo-chemical reactions, were found in the tribo-contact areas, depending on different wear conditions.     

Tribological study of peroxide-cured EPDM rubber filled with electron beam irradiated PTFE powder

The aim of this work is the evaluation of the effects of electron beam modification of Polytetrafluoroethylene (PTFE) powder on the friction and wear properties of PTFE filled Ethylene-Propylene-Diene-Monomer (EPDM) rubber cured by a radical-initiated peroxide system. Friction and wear properties of EPDM vulcanizates were determined with the help of pin-on-disc tribometer in sliding contact with a steel-ball at room temperature without lubrication. PTFE powder was modified in atmospheric conditions with low (20 kGy) and high (500 kGy) irradiation doses using electron beam accelerator. The spectroscopic investigations reveal that the increasing concentration of reactive free radicals and functional groups with irradiation dose has a drastic influence on crosslinking efficiency due to their interference with peroxide radicals in curing process. As a result, non-irradiated and low-irradiated PTFE filled EPDM with higher crosslinking densities showed remarkably enhanced friction and wear properties. On the contrary, 500 kGy PTFE filled EPDM having significantly lower crosslinking density resulted in poor friction and wear characteristics. The apparent crosslinking density measured directly from the curing curves was found to be the most dominating parameter influencing friction, wear as well as the physical properties.     

Wear mechanisms of PcBN cutting tools when dry turning ASTM Grade 2 austempered ductile iron under finishing conditions

Experimental studies of dry finish turning of ASTM Grade 2 austempered ductile iron with PcBN cutting tools were carried out at cutting speeds ranging from 50 to 800 m/min, at a feed of 0.05 mm/rev and depth cut of 0.2 mm. The wear mechanisms of PcBN cutting tools were investigated through the examination of the wear surfaces by means of optical, scanning electron and transmission electron microscopes as well as energy dispersive spectroscopy. Flank wear and crater wear were the main wear modes within this range of cutting speeds. Adhesion and adhesion induced abrasion were the main wear mechanisms at cutting speeds less than 150 m/min. Abrasion and wear by thermally activated-diffusion and oxidation-chemical reaction wear were the main wear mechanisms at cutting speeds greater than 150 m/min. A high concentration of Mg, Si, and O on the wear surfaces and a heat-affected zone in the tools suggested that at speeds in excess of 150 m/min, the rate controlling wear mechanism involved chemical reaction between the tools and the operating environment.     

Sliding wear behavior of hardfacing alloys in a pressurized water environment

In this study, sliding wear behavior of newly developed Fe-base Co-free hardfacing alloy (Fe–Cr–C–Si) was investigated and compared to that of Stellite 6 and Fe-base NOREM 02 in the temperatures ranging from 300 to 575 K under a contact stress of 103 MPa (15 ksi) in pressurized water. The weight loss of Fe–Cr–C–Si was equivalent to that of Stellite 6 over all temperatures range in 100-cycle wear test. The weight loss of Fe–Cr–C–Si 1000-cycle wear test increased almost linearly with increasing temperature up to 575 K. The weight loss of NOREM 02 was nearly equivalent to that of Stellite 6 below 475 K, however, galling occurred above 475 K in 100-cycle wear test. It was also found that the lubrication effect of pressurized water on the sliding wear behavior of the alloys was negligible under the present test conditions.     

Microscratch behavior of copper–graphite composites

Microscratch tests were carried out on Cu–graphite composites with graphite content of 0–30 vol% and normal loads of 0.5–2 N. Scratch grooves generated by the plastic deformation of surfaces were characterized for detailed friction and wear mechanisms investigation. The influence of normal load and graphite content on friction coefficient was also studied. It is found that the dominant wear mechanism transits from ploughing to micro-cutting with increasing the normal loads. A friction model for knowing the contribution of ploughing and adhesion components to friction is presented. This friction model is useful in understanding the friction mechanism of composites during scratching.