Effects of Water Content Distribution on Hydraulic Conductivity of Prehydrated GCLS against Calcium Chloride Solutions

When geosynthetic clay liners (GCLs) are applied as bottom liners at waste containment facilities, they are naturally prehydrated by absorbing moisture in the underlying base layers. In order to evaluate the effects of cations contained in waste leachates, this study investigated the effects of the water content distribution of the GCLs prehydrated with actual soils on their hydraulic conductivities against CaCl₂ solutions. The “prehydration tests”, which were conducted prior to the hydraulic conductivity tests, showed that the water content distribution of the prehydrated GCLs depends on the properties of the GCLs and the base layers. In particular, drastic differences between GCLs with powdered bentonite and GCLs with granular bentonite were observed in the prehydration water content and its distribution. Prehydrated GCLs with powdered bentonite had a higher water content and a more homogenous distribution than those with granular bentonite. The hydraulic conductivity tests showed that most of the prehydrated GCLs exhibit a low hydraulic conductivity of k?1.0×10^-8 cm/s against CaCl₂ solutions with 0.1-0.5 M. However, GCLs with granular bentonite may be difficult to homogeneously prehydrate and exhibit an unstable hydraulic conductivity, which varies from k=2.9×10^-9 cm/s to k=1.5×10^-6 cm/s. The homogeneity of the water content distribution has been considered an important factor to obtain a required barrier performance under prehydration conditions, which are naturally generated in actual sites.     

水泥固化体淋滤液对GCL防渗性能的影响

水泥固化/稳定化是危险废弃物处理的经济、高效方法,然而,水泥固化体的淋滤液中含有大量Ca~(2+),其长期渗透有可能导致填埋场底部土工合成黏土衬垫(geosyntheticclayliner,GCL)的防渗性能下降,从而引发二次污染。使用柔性壁渗透仪,测定有效应力和水泥固化体淋滤液共同作用下GCL的渗透系数,探讨了淋滤液浓度以及不同有效应力对GCL渗透系数的影响。试验结果表明:当有效应力为24kPa时,水泥固化体淋滤液的持续渗透会使GCL的渗透系数增大179～721倍,淋滤液中Ca~(2+)浓度越高,GCL渗透系数增大的幅度越大。通过增加有效应力,可以降低固化体淋滤液对GCL防渗性能所造成的负面影响,当有效应力增大至438 kPa时,固化体淋滤液对GCL防渗性能所造成的负面影响全部被抵消。     

Chemical interaction and hydraulic performance of geosynthetic clay liners isothermally hydrated from silty sand subgrade

The effects of the silt aggregation, compaction density, and water content of the subgrade on the hydration of five different geosynthetic clay liner (GCL) products is reported based on a series of laboratory column experiments conducted over a six-year period. GCLs meeting typical specifications in terms of minimum hydraulic conductivity and swell index are hydrated to equilibrium from the same subgrade soil with sufficient cations to cause cation exchange during hydration. It is then shown that the GCL bentonite granularity and GCL structure can have a significant (~four orders of magnitude) effect on hydraulic conductivity under the same test conditions (from 8 × 10⁻¹² m/s for one GCL to 6 × 10⁻⁸ m/s for another GCL product). The effect of subgrade water content on the hydraulic performance of GCLs are not self-evident and quite dependent on the bentonite granularity, GCL structure, and permeant. Varying the subgrade water content from 5 to 16% and allowing the GCL to hydrate to equilibrium before permeation led to up to 5-fold difference in hydraulic conductivity when permeated with tap water and up to 60-fold difference when the same product is permeated with synthetic municipal solid waste leachate. When permeated with synthetic leachate, increasing stress from 70 kPa to 150 kPa led to a slight (average 37%; maximum 2.7-fold) decrease in hydraulic conductivity due to a decrease in bulk void ratio. It is shown that hydraulic conductivity is lower for GCLs with a scrim-reinforced geotextile, and/or with finer bentonite. It is shown that selecting a GCL based on the initial hydraulic conductivity and swell index in a manufacturers product sheet provides no assurance of good performance in field applications and it is recommended that designers pay more attention to selection of a GCL and preparation of the subgrade for important projects.     

Investigating factors influencing polymer elution and the mechanism controlling the chemical compatibility of GCLs containing linear polymers

A study was conducted to investigate (1) physicochemical factors that influence polymer elution from GCLs containing a blend of bentonite and linear (water-soluble) polymer (LPB GCLs) and (2) the mechanism that controls the chemical compatibility of LPB GCLs when polymer elutes. A series of hydraulic conductivity (k), free swell and viscosity tests were performed on a commercial LPB GCL using DI water, varying concentrations of NaCl and CaCl?. Comparable tests were also performed on a conventional bentonite (CB) GCL containing the same untreated bentonite and the same physical properties as the LPB GCL. The LPB GCL showed improved swelling and hydraulic performance compared to the CB GCL when permeated with salt solutions. Total organic carbon analysis of the effluents showed that polymer eluted from the LPB GCL regardless of the permeant solution. However, the rate at which polymer eluted increased as the concentration and valence of the dominant cation increased. The rate at which polymer eluted also increased with hydraulic gradient. The mass of polymer retained inside the GCL matrix did not correlate with the k of the LPB GCL. Free swell tests coupled with chemical analysis suggest that, the improved chemical compatibility of the LPB GCL was due to the ability of the polymer to scavenge cations from the solution which allows the bentonite to undergo adequate swelling during the initial hydration period. Analogous to water-prehydrated CB GCLs, the dispersed structure of the bentonite fabric and increased adsorbed water molecules attained during initial swelling controls the k of the LPB GCL when polymer elutes.     

Hydraulic conductivity of bentonite-polymer geosynthetic clay liners to coal combustion product leachates

Hydraulic conductivity of seven geosynthetic clay liners (GCLs) to synthetic coal combustion product (CCP) leachates were evaluated in this study. The leachates are chemically representative of typical and worst scenarios observed in CCP landfills. The ionic strength (I) of the synthetic CCP leachates ranged from 50 mM to 4676 mM (TCCP-50, LRMD-96, TFGDS-473, LR-2577, HI-3179 and HR-4676). One of the GCLs contained conventional sodium bentonite (Na–B) and the other six contained bentonite-polymer (B–P) mixture with polymer loadings ranging from 0.5% to 12.7%. Hydraulic conductivity tests were conducted at an effective confining stress of 20 kPa. The hydraulic conductivity of the Na–B GCLs were >1 × 10⁻¹⁰ m/s when permeated with all six CCP leachates, whereas the B–P GCLs with sufficient polymer loading maintained low hydraulic conductivity to synthetic CCP leachates. All the B–P GCLs showed low hydraulic conductivity (<1 × 10⁻¹⁰ m/s) to low ionic strength leachates (TCCP-50, I = 50 mM and LRMD-96, I = 96 mM). B–P GCLs with P > 5% showed low hydraulic conductivity (<1 × 10⁻¹⁰ m/s) up to HI-3179 leachates. These results suggest that B–P GCLs with sufficient polymer loading can be used to manage aggressive CCP leachates.     

Hydraulic conductivity of geosynthetic clay liners to tailings impoundment solutions

The results of a comprehensive testing program conducted to evaluate the hydraulic conductivity (k) of two geosynthetic clay liners (GCLs) considered as a liner component for a tailings impoundment at a proposed zinc and copper mine are reported. The two GCLs were permeated with a relatively low ionic-strength ground water (GW) from the mine site and two electrolyte solutions, a process water (PW) and a simulated leachate (SL), with chemical compositions consistent with those expected during operation of the impoundment. A total of 22 flexible-wall tests were performed to determine the effects of prehydration with the GW, type of GCL, type of permeant liquid, and duration of the back-pressure stage of the test. The k values for both GCLs permeated with the GW were 1.7 × 10⁻⁹ cm/s, which is within the range 1–3 × 10⁻⁹ cm/s typically reported for GCLs permeated with low ionic-strength liquids, such as deionized water. However, the mean values of k based on permeation of duplicate specimens of both types of GCL with either PW or SL relative to the values of k based on permeation with GW, or k/k_w, ranged from a factor of 200 (2.3 orders of magnitude) to a factor of 7600 (3.9 orders of magnitude). Thus, both tailings impoundment solutions had significant adverse impacts on the hydraulic performance of both GCLs. Given the overall range of k/k_w values, factors such as prehydration, type of GCL, type of permeant liquid, and duration of back pressure, were relatively insignificant. The results of this study serve to emphasize the need to perform hydraulic conductivity testing using site specific materials.     

Combined effects of ammonium permeation and dry-wet cycles on the hydraulic conductivity and internal properties of geosynthetic clay liners

The hydraulic conductivity of geosynthetic clay liners (GCLs) permeated with deionized water (S0) and NH₄⁺ solutions, with concentrations of 100 mg/L (S100) and 1000 mg/L (S1000), was examined under six dry-wet cycles. The internal properties of virgin, desiccated, and healed GCLs were analyzed and quantified using X-ray computed tomography images. The hydraulic conductivity of the GCLs permeated with S0 and S100 underwent a negligible change during the six dry-wet cycles, whereas that of S1000 increased by almost three orders of magnitude after two desiccations. Each desiccation, after permeating with S0 and S100, generated a completely different macro-crack pattern; however, generation of macro-cracks at the same locations from dry cycles 2 to 6 and an abundance of micro-cracks were typical for S1000. This implies the severe deterioration of bentonite due to multi-desiccations and chemical compatibility with S1000. Moreover, the swell index of bentonite exposed to S1000 was reduced by approximately half, after six dry-wet cycles. Despite the lower volume percentage of macro-cracks for S1000 compared to S0 and S100, the swelling capacity of this bentonite was insufficient to fully heal these cracks. Hence, the swelling properties of bentonite dominate crack volume with regard to determining the hydraulic conductivity of GCLs.     

Hydrodynamic assessment of bentonite granule size and granule swelling on hydraulic conductivity of geosynthetic clay liners

Flow in an idealized geosynthetic clay liner (GCL) containing bentonite comprised of equisized and equispaced square granules was simulated using a hydrodynamic model to quantitatively evaluate the premise that the hydraulic conductivity of GCLs diminishes as the bentonite granules hydrate and swell into adjacent intergranular pores, creating smaller and tortuous intergranular flow paths. Predictions with the model indicate that hydraulic conductivity decreases as granules swell and intergranular pores become smaller, and that greater granule swelling during hydration is required to achieve low hydraulic conductivity when the bentonite is comprised of larger granules, or the bentonite density is lower (lower bentonite mass per unit area). Predictions made with the model indicate that intergranular pores become extremely small (<1 μm) as the hydraulic conductivity approaches 10⁻¹¹ m/s. These outcomes are consistent with experimental data showing that GCLs are more permeable when hydrated and permeated with solutions that suppress swelling of the bentonite granules, and that the hydraulic conductivity of GCLs with bentonite having smaller intergranular pores (e.g., GCLs with smaller bentonite granules, more broadly graded particles, or higher bentonite density) is less sensitive to solutions that suppress swelling.     

Stress-controlled direct shear testing of geosynthetic clay liners I: Apparatus development

The use of geosynthetic clay liners (GCLs) in waste containment applications can induce long-term normal and shear stresses as well as expose GCLs to elevated temperatures and non-standard hydration solutions. Considering the importance of GCL internal shear strength to the design and integrity of waste containment barrier systems, innovative laboratory testing methods are needed to assess shear behavior of GCLs. There were two main objectives of this study: (i) develop a stress-controlled direct shear apparatus capable of testing GCLs exposed to elevated temperatures and hydrated in non-standard solutions; and (ii) assess internal shear behavior of GCLs under varying experimental conditions (e.g., stress, temperature, solution). These two objectives were partitioned into a two-paper set, whereby Part I (this paper) focuses on the shear box design and Part II focuses on an assessment of shear behavior. The direct shear apparatus includes a reaction frame to mitigate specimen rotation that develops from an internal moment within needle-punched reinforced GCLs. Rapid-loading shear tests were conducted to assess functionality of the apparatus and document baseline shear behavior for a heat-treated and a non-heat treated needle-punched GCL with comparable peel strength. These two GCLs failed at comparable applied shear stress; however, the heat-treated GCL yielded lower shear deformation and failure occurred via rupture of reinforcement fiber anchors, whereas the non-heat treated GCL yielded larger shear deformation and failure via pullout of reinforcement fibers.     

Hydraulic conductivity of two geosynthetic clay liners permeated with a hyperalkaline solution

GCLs containing powdered Na-bentonite treated with different dosages of a proprietary additive intended to reduce the impacts of chemical interactions were permeated with three solutions: a hyperalkaline solution (1 M NaOH and 1.3 mM CsCl) having similar pH to aluminum refining leachate, a 1.3 mM CsCl solution (no NaOH), and DI water. For a given permeant solution, the hydraulic conductivity of both GCLs was similar. Thus, the higher additive dosage had no measureable impact on hydraulic conductivity. Hydraulic conductivity of both GCLs decreased by a factor of approximately 1.5–1.8 during permeation with CsCl in response to osmotic swelling induced by the low ionic strength of the CsCl solution entering the pore space. In contrast, permeation with the NaOH–CsCl solution caused the hydraulic conductivity of both GCLs to increase modestly (<50 times the hydraulic conductivity to DI water), and then level out (or decrease slightly) as a result of reduced osmotic swelling in the interlayer combined with dissolution of the mineral. For the tests conducted with CsCl solution, nearly all of the Cs was adsorbed by the bentonite. In contrast, Cs broke through readily when the NaOH–CsCl solution was used as the permeant solution. Permeation with the NaOH–CsCl solution also increased the sodicity of the bentonite by replacing bound K, Ca, and Mg on the mineral surface.     

Geosynthetic clay liners: Perceptions and misconceptions

The behaviour of geosynthetic clay liners (GCLs) as part of a physical-environmental system is examined. Consideration is given to: (a) both the physical and hydraulic interactions with the materials, and the chemical interactions with the fluids, above and below the liner, (b) time-dependent changes in the materials, (c) heat generated from the material to be contained, as well as (d) the climatic conditions both during construction and during service. This paper explores some common perceptions about GCL behaviour and then examines the misconceptions that can arise and their implications. It demonstrates how what may first appear obvious is not always as one expects and that more is not always better. It discusses: (i) the pore structure of a GCL, (ii) the dependency of the water retention curve of the GCL on its structure, bentonite particle sizes and applied stress, (iii) the effect of the subgrade pore water chemistry, (iv) the mineralogy of the subgrade, and (v) thermal effects. The desirability of a GCL being reasonably well-hydrated before being permeated is examined. The critical size of needle-punch bundles at which preferential flow can increase hydraulic conductivity by orders of magnitude is illustrated. The dependency of self-healing of holes on the interaction between GCL and subgrade is discussed. Finally, the transmissivity of the geomembrane/GCL interface is shown to be a function of GCL and geomembrane characteristics and to be poorly correlated with GCL hydraulic conductivity.     

Laboratory investigation of GCL hydration from Lateritic subsoils

A laboratory investigation on the hydration behavior of GCLs from lateritic soils was conducted under isothermal and thermal conditions (tropical climate), varying subsoil moisture contents, GCLs bentonite particle size and mineralogy. GCL hydration levels from lateritic subsoils under isothermal conditions (55%) were similar to literature findings. A slight decrease in water content of some GCLs after long periods of contact with the lateritic soils indicates that equilibrium can demand long time in these soils. GCL with granular bentonites were less efficient to hydrate from lateritic subsoils. GCLs with activated-calcium bentonites maintained hydration levels in long-term. Nonwoven geotextile facing down favored capillary effects. Thermal cycles significantly influenced GCLs hydration from subsoils. Capillary connections developed during hydration under isothermal conditions due to suction gradient reductions. Post-hydration tests under isothermal conditions showed more alterations in GCLs swelling and cation exchange properties than thermal cycles test. An increase in the saturated hydraulic conductivity of GCLs was observed in both lateritic soils, mainly for isothermal condition, although continued attending hydraulic conductivity requirements for barrier applications.     

Hydraulic conductivity of bentonite-polymer composite geosynthetic clay liners permeated with bauxite liquor

The high ionic strength of the porewater in red mud (bauxite liquor from digestion) can suppress swelling of montmorillonite, resulting in geosynthetic clay liners (GCLs) that are too permeable to be effective as liners in red mud disposal facilities. Bentonite-polymer composite GCLs (BPC GCLs) have been developed as more resilient lining materials, and some BPC GCLs have been shown to have very low hydraulic conductivity to bauxite liquors that have extreme ionic strength and pH. In this study, a nationwide investigation was conducted in China to evaluate the characteristics of bauxite liquor in Chinese impoundments, and to evaluate the suitability of GCLs containing granular sodium bentonite or BPCs for containment. Hydraulic conductivity tests were conducted on six BPC GCLs with two characteristic Chinese bauxite liquors that are hyperalkaline (pH > 12) and had ionic strengths of 76.9 mM and 620.3 mM. The BPC GCLs had hydraulic conductivity ranging from 10^?8-10^?12 m/s, which is higher than the hydraulic conductivity of BPC GCLs to deionized water (10^?12-10^?13 m/s), but lower than the hydraulic conductivity of conventional GCLs with granular sodium bentonite GCLs to the same liquors (10^?7-10^?8 m/s). The hydraulic conductivity of the BPC GCLs depends on the chemical properties of the leachate, the polymer loading, and the type of polymer. Microstructural analysis by scanning electron microscopy (SEM) suggests that the hydraulic conductivity of BPC GCLs is controlled by pore-blocking by polymer hydrogel, which is affected by the bauxite liquor.     

Effect of stress on water retention of needlepunched geosynthetic clay liners

Geosynthetic clay liners (GCLs) are placed at the bottom of waste disposal facilities where they hydrate from the subsoil and eventually from a hydraulic head on geomembranes (GMs) defects. Predicting hydration behavior of GCLs requires knowledge of the water-retention properties of the GCL along wetting paths. Given that GCLs could be subjected to different ranges of vertical stresses that are induced by the weight of the supported waste, the confining stress could affect water-retention properties of GCLs and should be investigated. To do so, a laboratory methodology to establish the water-retention curves (WRCs) of needlepunched GCLs under stress was undertaken. Various constant vertical stresses corresponding to different weights of the supported waste were applied to GCL specimens placed in controlled-suction oedometers. Suction values were selected so as to mimic a wetting path from the initial dry state to zero suction. Suction was controlled by using controlled suction techniques with controlled humidity imposed by a saturated saline solutions and using the osmotic technique with polyethylene glycol (PEG) solutions. Measurements were undertaken on oedometer systems as to apply confining stresses and have been complemented by standard saturated oedometer swelling tests. The data obtained confirm that increasing the stress on to the GCL results in less, albeit faster, water uptake, which could emphasize on recommendations about rapidly covering GCLs after they are placed at the bottom of a waste disposal facilities. Finally, the potential validity of the state-surface concept, which was developed in unsaturated soil mechanics, is discussed using van Guenuchten's and Fredlund and Xing's equations for water retention curves.     

Effect of ammonium on the hydraulic conductivity of geosynthetic clay liners

Hydraulic conductivity and swell index tests were conducted on a conventional geosynthetic clay liner (GCL) containing sodium-bentonite (Na-B) using 5, 50, 100, 500, and 1000 mM ammonium acetate (NH₄OAc) solutions to investigate how NH₄⁺ accumulation in leachates in bioreactor and recirculation landfills may affect GCLs. Control tests were conducted with deionized (DI) water. Swell index of the Na-B was 27.7 mL/2 g in 5 mM NH₄⁺ solution and decreased to 5.0 mL/2 g in 1000 mM NH₄⁺ solution, whereas the swell index of Na-B in DI water was 28.0 mL/2 g. Hydraulic conductivity of the Na-B GCL to 5, 50, and 100 mM NH₄⁺ was low, ranging from 1.6–5.9 × 10^?11 m/s, which is comparable to the hydraulic conductivity to DI water (2.1 × 10^?11 m/s). Hydraulic conductivities of the Na-B GCL permeated with 500 and 1000 mM NH₄⁺ solutions were much higher (e.g., 1.6–5.2 × 10^?6 m/s) due to suppression of osmotic swelling. NH₄⁺ replaced native Na⁺, K⁺, Ca²⁺, and Mg²⁺ in the exchange complex of the Na-B during permeation with all NH₄⁺ solutions, with the NH₄⁺ fraction in the exchange complex increasing from 0.24 to 0.83 as the NH₄⁺ concentration increased from 5 to 1000 mM. A Na-B GCL specimen permeated with 1000 mM NH₄⁺ solution to chemical equilibrium was subsequently permeated with DI water. Permeation with the NH₄⁺ converted the Na-B to “NH₄-bentonite” with more than 80% of the exchange complex occupied by NH₄⁺. Hydraulic conductivity of this GCL specimen decreased from 5.9 × 10^?6 m/s to 2.9 × 10^?11 m/s during permeation with DI water, indicating that “NH₄-bentonite” can swell and have low hydraulic conductivity, and that the impact of more concentrated NH₄⁺ solutions on swelling and hydraulic conductivity is reversible.     

Irrigated composite liner designs for fast hydration and prevention of thermal desiccation of geosynthetics clay liners

In composite liners made of geomembrane (GMB)-geosynthetics clay liners (GCLs), maintaining bentonite in the GCL in a suitably hydrated state is critical for their performance. Hydration of GCL from subsoil, following industry best practice, is time consuming and conditional on suitable water chemistry in subsoil. In addition, under thermal gradients, dehydration occurs, with moisture migrating downwards to the subsoil, leading to the development of cracks in the bentonite and hence loss of performance.Two novel ideas are proposed in this paper, namely hydration of GCLs by artificial irrigation and hydraulic separation of the liner system from the underlying subsoil. Three new composite liner designs allowing for actively irrigating a geosynthetic clay liner (GCL) through a geocomposite layer were investigated. In two of the three designs, the hydraulic connection between the GCL and the subsoil was broken by placing an additional GMB between them. The new designs were tested in column experiments under 20 kPa overburden pressure and temperatures of up to 78 °C applied to the top of the liner. The performances of the new designs were compared to that of a standard GCL-GMB design where GCL was allowed to hydrate from a well-graded sandy subsoil. Three scenarios for the staging of hydration and thermal load application were investigated.Under active hydration of the composite liners, it took less than 14 days for the GCLs to reach a gravimetric water content ω of 110–130%, compared to 49 days taken to reach ω~95% under hydration from the subsoil. GCLs in the new designs in which the hydraulic connection with the subsoil was broken, remained well-hydrated (ω>100%) after 14 days of heating and no cracks appeared in the bentonite. On the other hand, the GCL in the conventional design experienced severe desiccation under the same conditions. The new designs hence offer a viable solution to the problem of slow hydration and/or thermal desiccation of GCLs.     

赤泥渗滤液对改性GCL防渗性能的影响

旨在评价商用土工合成材料黏土衬垫(GCL)用于阻隔赤泥渗滤液的有效性.赤泥渗滤液作用下GCL的防渗特性是评价其防污性能的关键因素.以商用改性GCL中膨润土为研究对象,通过自由膨胀试验,研究了4种赤泥渗滤液中膨润土的自由膨胀指数.以商用改性GCL为研究对象,通过改进滤失试验,研究了4种赤泥渗滤液作为渗透液作用下GCL渗透...     

Effect of wet-dry cycles on standard & polymer-amended GCLs in covers subjected to flow over the GCL

The performance of five different GCLs (two GCLs with standard sodium bentonite and three GCLs with polymer enhanced bentonite) subjected to three different climatic modes of wet-dry cycles simulating conditions to which a GCL might expose in cover systems over a prolonged time is reported. The wetting cycles lasted for 8 h, while the drying cycles varied between 16 h, seven days, and 14 days. It is shown that after around a year of accelerated aging, the hydraulic conductivity of the aged GCLs increased notably when permeated with tap water at an applied effective stress of 15 kPa for a range of heads (0.07, 0.14, 0.21, 0.49, and 1.2 m). The combined effects of the number and the duration of the wet-dry cycles, the GCL's mass per unit area, the carrier geotextile, the size and the number of the needle punch bundles, and the thermal treatment to bond the needle-punch bundles to the carrier geotextile are discussed. The poor hydraulic performance of the polymer-amended/modified bentonite GCLs is discussed.     

Redox Effect on the Hydraulic Conductivity of Clay Liner

Microbial activities can be enhanced by organic rich leachate occurring in solid waste landfills, which possesses the potential to alter the barrier capacity of clay liners. Flexible-wall hydraulic conductivity tests are conducted to investigate the effect of the microbial activities on the hydraulic conductivity of Osaka marine clay used for clay liners of offshore solid waste landfill sites in Japan. Permeants with different redox potentials are employed to investigate the redox effect; and, permeants with high nutrients are used to check the effect of the microbial production in soil specimens. Test results indicate that there are no obvious changes in the free swell index, the liquid limit, or the hydraulic conductivity of the marine clay when a strong reducing agent is used. When nutrients are applied for the growth of microorganisms, however, a decrease in hydraulic conductivity, ranging from greater than two orders of magnitude to less than one order of magnitude, is observed. The formation of biofilm and anaerobic inorganic precipitation on the surface of the soil particles is considered to be responsible for this reduction in hydraulic conductivity. Test results reveal that microbial activities, enhanced by landfill leachate, may not cause an increase in the hydraulic conductivity of natural clay liners of offshore landfill sites.