Measurements of thermal conductivity of 1‐butyl‐3‐methylimidazolium tetrafluoroborate at high pressure

Ionic liquids are salts that are liquid at room temperature. They have attracted considerable attention as new materials. In this study, a transient short‐hot‐wire apparatus was prepared, and the thermal conductivity of 1‐butyl‐3‐methylimidazolium tetrafluoroborate ([bmim] [BF₄]) was measured. The experimental temperatures were from 294 to 334 K, and the pressures were from 0.1 to 20 MPa. It was found that the thermal conductivity of an ionic liquid has a very small temperature and pressure dependence. © 2007 Wiley Periodicals, Inc. Heat Trans Asian Res, 36(6): 361–372, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20166     

A study on thermal conductivity of a mixture of magnesia particles and molten nitrate by a transient hot wire method

In this study, the effective thermal conductivity of a mixture of magnesia particles and molten nitrate used in a high temperature thermal energy storage system was investigated by a transient hot wire method. The effective thermal conductivity of the mixture was around 2.0W/(m·K) in the temperature range of 423 K to 703 K, although it decreased about 5% with increasing temperature. This value was about 10 times larger than that of the packed bed of magnesia particles including air. The effective thermal conductivity increased about 3% with a 1% increase in the volume ratio of magnesia particles in the mixture with molten nitrate. © 2006 Wiley Periodicals, Inc. Heat Trans Asian Res, 35(4): 245–253, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20116     

Study of viscosity and thermal conductivity effects on condensation characteristics of some new alternative refrigerant mixtures

In this paper, a numerical study of the impact of the transport properties on the condensation characteristics of certain refrigerant mixtures is presented. New correlations have been developed to calculate the thermal conductivity and viscosity of some alternative refrigerant mixtures such as R-507, R-404A, R-407C, and R-410A. In addition, new improved condensation correlations have been developed and presented for predicting the heat transfer coefficient and pressure drop. The results clearly showed that the condensation characteristics were well predicted using the newly proposed correlations with mean deviation of ±10 and 20% for the heat transfer coefficient and pressure drop respectively. Copyright © 2002 John Wiley & Sons, Ltd.     

Transient response for a half-space with variable thermal conductivity and diffusivity under thermal and chemical shock

The present work aims to investigate the transient thermoelastic diffusive response for a half-space with variable thermal conductivity and diffusivity in the context of the generalized thermoelastic diffusion theory. The boundary plane of the half-space is assumed to be traction free and subjected to a time-dependent thermal and chemical shock. The governing equations of the problem are formulated by using Kirchhoff’s transformation. Due to the complexity of the equations, Laplace transformation method is applied to solve them. Numerical results are obtained and illustrated graphically. Parameter studies are performed to evaluate the effects of variable thermal conductivity and diffusivity on the response. The present investigation could be helpful for better understanding the multifield coupling effect of mechanical and thermal fields in real materials.     

Temperature dependence of thermal conductivity and thermal diffusivity of some composites using the transient plane source technique

The recently developed transient plane source (TPS) technique has been applied for the simultaneous measurement of thermal conductivity and thermal diffusivity of two composite materials namely, marble and magnesium oxychloride cement in the range of temperatures from 30 to 150°C. The experimental results of these samples show that there is very slight variation in thermal conductivity and thermal diffusivity of these materials in this range of temperature. An effort has been made to express this variation of thermal conductivity and diffusivity with temperature by a linear relation, in these materials.     

Measurements of the thermal diffusivity of linear-medium-density-polyethylene/aluminium composites using a transient comparative method

Metal-powder/polymer composites are an interesting class of material because their physical properties may, within limits, be selected to match a particular application. It is therefore important to be able to measure and model the physical properties of these composites. The effective diffusivity of linear-medium-density-polyethylene/aluminium composites was measured for a range of volume fractions using a simple, transient comparative method. Effective thermal conductivity data were calculated from the effective thermal diffusivity data. The effective thermal conductivity data were modelled well by the EMT equation.     

Simultaneous measurements of thermal conductivity and thermal diffusivity of insulators,fluids and conductors using the transient plane source (TPS) technique

Simultaneous measurements of thermal conductivity and thermal diffusivity of composite red-sand bricks, glycerine and mercury have been made at room temperature by the recently developed transient plane source (TPS) technique. This paper describes, in brief, the theory and the experimental conditions for the simultaneous measurements of thermal conductivity and thermal diffusivity of insulators, fluids and metals. The source of heat is a hot disc made out of bifilar spirals. The disc also serves as a sensor of temperature increase in the sample. The measured values of the thermal conductivity and thermal diffusivity of these samples are in agreement with the values reported earlier using other methods. The advantage of the TPS technique is the simplicity of the equipment, simultaneous information on thermal conductivity and thermal diffusivity, and also the applicability of the technique to insulators, fluids and metals.     

A study on thermal conductivity of a quasi‐ordered liquid layer on a solid substrate

In the present paper, a study on thermal conductivity of a quasi‐ordered liquid layer on a solid surface was performed by molecular dynamic simulation. Results showed that the motion of the molecules and their radial distribution function in the quasi‐ordered liquid layer were similar to those of solid molecules. By using the Green–Kubo formula, the thermal conductivity of the layer was calculated. It was found that it increased with the increase of the parameters of ordering. The size effect and the influence of the boundary condition were also discussed. © 2007 Wiley Periodicals, Inc. Heat Trans Asian Res, 36(7): 429–434, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20171     

Application of the Haar wavelet method on a continuously moving convective‐radiative fin with variable thermal conductivity

In this paper, we numerically investigate the heat transfer in a continuously moving convective‐radiative fin with variable thermal conductivity by using Haar wavelets. Heat is dissipated to the environment simultaneously through convection and radiation. The effect of various significant parameters—in particular the thermal conductivity parameter a, convection‐sink temperature θ_a, radiation‐sink temperature θ_s, convection‐radiation parameter N_c, radiation‐conduction parameter N_r, and Peclet number Pe—on the temperature profile of the fin are discussed and interpreted physically through illustrative graphs. Computational results obtained by the present method are in good agreement with the standard numerical solutions. © 2013 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley Online Library (wileyonlinelibrary.com/journal/htj). DOI 10.1002/htj.21038     

Thermal Conductivity Measurement of Semitransparent Media at Temperatures from 300 to 800 K by Hot—Wire Method

ＴｈｅｒｍａｌＣｏｎｄｕｃｔｉｖｉｔｙＭｅａｓｕｒｅｍｅｎｔｏｆＳｅｍｉｔｒａｎｓｐａｒｅｎｔＭｅｄｉａａｔＴｅｍｐｅｒａｔｕｒｅｓｆｒｏｍ３００ｔｏ８００ＫｂｙＨｏｔ－ＷｉｒｅＭｅｔｈｏｄＴｈｅｒｍａｌＣｏｎｄｕｃｔｉｖｉｔｙＭｅａｓｕｒｅｍｅｎｔ...     

纳米流体稳定性及其导热性能研究

为了探究影响纳米流体稳定性和导热系数的因素,采用一步法和两步法分别制备了SiO2-EG/DW(50∶50)纳米流体和SiO2-EG纳米流体,探讨团聚体等效直径对纳米流体稳定性的影响.基于瞬态热线法的原理,测量一步法纳米流体的导热系数,分析温度和纳米颗粒质量分数对其导热系数的影响.结果表明:相比一步法制备的纳米流体,两步...     

Determination of temperature distribution for annular fins with temperature‐dependent thermal conductivity

In this paper, homotopy analysis method (HAM) has been used to evaluate the temperature distribution of annular fin with temperature‐dependent thermal conductivity and to determine the temperature distribution within the fin. This method is useful and practical for solving the nonlinear heat transfer equation, which is associated with variable thermal conductivity condition. HAM provides an approximate analytical solution in the form of an infinite power series. The annular fin heat transfer rate with temperature‐dependent thermal conductivity has been obtained as a function of thermo‐geometric fin parameter and the thermal conductivity parameter describing the variation of the thermal conductivity. © 2011 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley Online Library ( wileyonlinelibrary.com/journal/htj ). DOI 10.1002/htj.20353     

Back‐analyses of in‐situ thermal response test (TRT) for evaluating ground thermal conductivity

In this study, a series of computational fluid dynamics (CFD) numerical analyses was performed in order to evaluate the performance of six full‐scale closed‐loop vertical ground heat exchangers constructed in a test bed located in Wonju, South Korea. The high‐density polyethylene pipe, borehole grouting and surrounding ground formation were modeled using FLUENT, a finite‐volume method program, for analyzing the heat transfer process of the system. Two user‐defined functions accounting for the difference in the temperatures of the circulating inflow and outflow fluid and the variation of the surrounding ground temperature with depth were adopted in the FLUENT model. The relevant thermal properties of materials measured in laboratory were used in the numerical analyses to compare the thermal efficiency of various types of the heat exchangers installed in the test bed. The numerical simulations provide verification for the in‐situ thermal response test (TRT) results. The numerical analysis with the ground thermal conductivity of 4.0 W/m?K yielded by the back‐analysis was in better agreement with the in‐situ TRT result than with the ground thermal conductivity of 3.0 W/m?K. From the results of CFD back‐analyses, the effective thermal conductivities estimated from both the in‐situ TRT and numerical analysis are smaller than the ground thermal conductivity (=4.0 W/m?K) that is input in the numerical model because of the intrinsic limitation of the line source model that simplifies a borehole assemblage as an infinitely long line source in the homogeneous material. However, the discrepancy between the ground thermal conductivity and the effective thermal conductivity from the in‐situ TRT decreases when borehole resistance decreases with a new three pipe‐type heat exchanger leads to less thermal interference between the inlet and outlet pipes than the conventional U‐loop type heat exchanger. Copyright © 2012 John Wiley & Sons, Ltd.     

Estimating error in measuring thermal conductivity using a T‐type nanosensor

We discuss the measurement error caused by fabrication and measurement of a T‐type nanosensor with a suspended sub‐micrometer Pt hot film that was developed to measure the thermal properties of individual nanowire materials. Comparison of numerical simulation and one‐dimensional analysis revealed that the thermal conductivity of nanowire material such as a carbon nanotube is calculated to be 17% lower. As an example, the thermal conductivity measurement result for a SiC nanowire is reported. The error caused by contact thermal resistance is found to depend on the contact length and can be as great as 20%. It can be said that future measuring can have higher reliability by correcting the estimated measurement error. © 2009 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20228     

Numerical and experimental studies on the measurement of thermal conductivity of a silicone rubber plate as a reference material

Silicone rubber is used as a reference material to examine the accuracy of measuring apparatus. However, the thermal conductivity of silicone rubber has been reported as ranging from 0.20 to 0.25 W/(m·K) at 293.15 K; thus an engineer cannot determine the accuracy of measuring apparatus. In order to obtain the exact value for the thermal conductivity of silicone rubber, the authors have developed a measuring apparatus according to the Guarded Hot Plate method. The dimensions of the test sample were 100 mm x 100 mm x 10 mm. This is sufficient to measure thermal conductivities ranging from 0.18 to 0.26 W/(m·K). The thermal conductivity obtained for a silicone rubber plate in this study was close to 0.25 W/(m·K). It was found that deformation of the silicone rubber has an effect on the thermal conductivity. The accuracy of our thermal conductivity measurement is estimated to be within ±3.5%. © Scripta Technica, Heat Trans Jpn Res, 26(7): 435–448, 1997     

A revised viscoelastic micropolar nanofluid model with motile micro‐organisms and variable thermal conductivity

In the present study, a magnetized micropolar nanofluid and motile micro‐organism with variable thermal conductivity over a moving surface have been discussed. The mathematical modeling has been formulated using a second‐grade fluid model and a revised form of the micropolar fluid model. The governing fluid contains micro‐organisms and nanoparticles. The resulting nonlinear mathematical differential equations have been solved with the help of the homotopy analysis method. The graphical and physical features of buoyancy force, micro‐organisms, magnetic field, microrotation, and variable thermal conductivity have been discussed in detail. The numerical results for Nusselt number, motile density number, and Sherwood number are presented with the help of tables. According to the graphical effects, it is noted that the buoyancy ratio and the bioconvection parameter resist the fluid motion. An enhancement in the temperature profile is observed due to the increment in thermal conductivity. Peclet number tends to diminish the motile density profile; however, the viscoelastic parameter magnifies the motile density profile.     

Thermal conductivity of wool and wool–hemp insulation

Measurements have been obtained for the thermal resistance of sheep‐wool insulation and wool–hemp mixtures, both in the form of bonded insulation batts, using a calibrated guarded hot‐box. The density was 9.6–25.9 kg m^?3 for the wool and 9.9–18.1 kg m^?3 for the wool–hemp mixtures. The measurements were made at a mean sample temperature of 13.3°C using a calibrated guarded hot‐box. The estimated uncertainly in the resistance measurements was of the order of ±7%. The thermal conductivity of the samples, derived from the thermal resistance measurements on the basis of the measured thickness, was well correlated with the density, although the variation with density was larger than that obtained in previous studies. The conductivity of the wool–hemp samples was not significantly different from that of the wool samples at the same density. Moisture uptake produced an increase of less than 5% in the conductivity of the bonded wool insulation for an increase in absorbed moisture content of 20%. The thermal resistance was 1.6% lower on average for samples oriented in the horizontal plane rather than the vertical plane, but this difference is not significant. Copyright © 2005 John Wiley & Sons, Ltd.     

Three-dimensional thermal weight function method for the interface crack problems in bimaterial structures under a transient thermal loading

Different from previous two-dimensional thermal weight function (TWF) method, a three-dimensional (3D) TWF method is proposed for solving elliptical interface crack problems in bimaterial structures under a transient thermal loading. The present 3D TWF method based on the Betti's reciprocal theorem is a powerful tool for dealing with the transient thermal loading due to the stress intensity factors (SIFs) of whole transient process obtained through the static finite element computation. Several representative examples demonstrate that the 3D TWF method can be used to predict the SIFs of elliptical interface crack subjected to transient thermal loading with high accuracy. Moreover, numerical results indicate that the computing efficiency can be enhanced when dealing with transient problems, especially for large amount of time instants.     

The flow characteristics of an upward gas‐liquid two‐phase flow in a vertical tube with a wire coil: Part 2. Effect on void fraction and liquid film thickness

An experimental study has been carried out to clarify the characteristics of the void fraction and the liquid film thickness of the air‐water two‐phase flow in vertical tubes of 25‐mm inside diameter with wire coils of varying wire diameter and pitch. The flow pattern in the experiment on the average void fraction and the local void fraction distribution in cross section was a bubble flow, and the liquid film thickness was in the region of semiannular and annular flows. It is clarified from these experiments that the average void fraction in tubes with wire coils is lower than that in a smooth tube and decreases with the wire diameter owing to the centrifugal force of the swirl flow which concentrates bubbles at the center of the tube, that the local liquid film thickness becomes more uniform with a decrease in the pitch of the wire coil, and that the liquid film becomes thicker after the passage through the wire coil with an increase in the wire diameter. © 2002 Wiley Periodicals, Inc. Heat Trans Asian Res, 31(8): 652–664, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.10067     

Prediction of the capacity of a heat exchanger by a thermal network method: Modified effective specific heat model considering the influence of static pressure distributions of refrigerants

In this paper, we proposed a method to predict the capacity of a heat exchanger by considering static pressure distributions of refrigerants. The thermal network method was modified by adding an equivalent heat generation term into a heat balance equation that was connected with calculated 1D static pressure distributions of refrigerants. An experiment was performed with a heat exchanger having two rows and two passes to verify the accuracy of the proposed method. The result showed the error of the predicted capacity to be less than 1% for an evaporator and less than 2% for a condenser. © 2002 Wiley Periodicals, Inc. Heat Trans Asian Res, 31(5): 376–390, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.10039