Electrochemical synthesis and corrosion performance of poly(pyrrole-co-o-anisidine)

The electrochemical synthesis of poly(o-anisidine) homopolymer and its copolymerization with pyrrole have been investigated on mild steel. The copolymer films have been synthesized from aqueous oxalic acid solutions containing different ratios of monomer concentrations: pyrrole:o-anisidine, 9:1, 8:2, 6:4, 1:1. The characterization of polymer films were achieved with FT-IR, UV–visible spectroscopy and cyclic voltammetry techniques. The electrochemical synthesis of homogeneous-stable poly(o-anisidine) film with desired thickness was very difficult on steel surface. Therefore its copolymer with pyrrole has been studied to obtain a polymer film, which could be synthesized easily and posses the good physical–chemical properties of anisidine. The kinetics and rate of copolymer film growth were strongly related to monomer feed ratio. The introduction of pyrrole unit into synthesis solution increased the rate of polymerization and the substrate surface became covered with polymer film soon, while this process required longer periods in single o-anisidine containing solution. The protective behavior of coatings has been investigated against steel corrosion in 3.5% NaCl solution. For this aim electrochemical impedance spectroscopy (EIS) and anodic polarization curves were utilized. The synthesized poly(o-anisidine) coating exhibited significant protection efficiency against mild steel corrosion. It was shown that 6:4 ratio of pyrrole and anisidine solution gave the most stable and corrosion protective copolymer coating.     

The electrochemical synthesis of poly(aniline-co-o-anisidine) on copper and their corrosion performances

The copolymer films PANI-co-POA and poly(aniline-co-o-anisidine) were carried out on copper (Cu) electrode, by applying two different scan rates (20 and 50 mV s⁻¹) and using two different thicknesses at high scan rate. Synthesizes were achieved under cyclic voltammetric conditions from 0.075 M aniline and 0.075 M o-anisidine containing sodium oxalate solutions. The synthesized copolymer films were strongly adherent and homogeneous in both cases. AC impedance spectroscopy (EIS), anodic polarization plots and open circuit potential–time curves were used to evaluate the corrosion performance of copolymer coated and uncoated electrodes in 3.5% NaCl. It was shown that the copolymer film coated at low scan rate exhibited a better property initially when compared with the copolymer film produced at high scan rate. However, it could not resist the attack of corrosion products, in longer time and meanwhile its barrier property significantly diminished. It was found that the thin copolymer film produced at high scan rate by its catalysing effect led to the formation of highly protective copper oxides on the surface whereby providing a better protection for long exposure times. It also emerged that the corrosion resistances of thin copolymer film produced at high scan rate and copolymer film synthesized at low scan rate were almost same and relatively higher for much longer periods when compared with the one observed for bare copper electrode.     

Electrochemical synthesis of bilayer coatings of poly(N-methylaniline) and polypyrrole on mild steel and their corrosion protection performances

Homopolymer and bilayer coatings of poly(N-methylaniline) (PNMA) and polypyrrole-dodecylsulfate (PPy-DS) have been electropolymerized on a mild steel (MS) surface by the potentiodynamic method in aqueous oxalic acid solutions. In order to include dodecylsulfate ion as dopant in the polypyrrole, sodium dodecylsulfate was also added to the polymerization solution of pyrrole. Characterization of coatings was carried out by the cyclic voltammetry, Fourier transform infrared (FTIR) spectroscopy and field emission scanning electron microscopy (FESEM). Corrosion behavior of the polymer coated MS electrodes was investigated in highly aggressive 0.5 M HCl solution by the Tafel test and electrochemical impedance spectroscopy (EIS) techniques. Corrosion test revealed that among the protective coatings obtained, the PNMA/PPy-DS bilayer exhibited the best corrosion resistance at all immersion times.     

Electrochemical synthesis and characterization of novel electrochromic poly (3,4-ethylenedioxythiophene-co-Diclofenac) with surfactants

Copolymers prepared from 3,4-ethylenedioxythiophene (EDOT) and Diclofenac (DCF) through cyclic voltammetric method exhibited electroactive and electrochromic behaviours. Addition of DCF produced bathochromic shift of the EDOT main absorption band from 253.4 to 269.7 nm in the UV-vis spectra. The cyclic voltammetric studies were carried out with different feed concentration of DCF and in the presence of two different surfactants, SDS and CTAB on glassy carbon electrode surface. Effect of scan rate on the three types of electroactive copolymer films was studied. The three different copolymers showed good adherence on the glassy carbon electrode surface in aqueous 0.1 M KCl medium. Spectroelectrochemical analysis of copolymer film was carried out on Indium-Tin-Oxide (ITO) plate and it showed multicolor electrochromic behaviour when the applied potential was changed. The color of the copolymer was changed from neutral yellow to brown and to violet in 0.1 M KCl medium. Among the three different copolymers, the copolymer prepared in presence of CTAB resulted in high contrast colors. The electrochromic parameters such as coloration efficiency, optical contrast, response time and stability were also evaluated. The surface morphology of the copolymer films was characterized by SEM analysis.     

Electrocatalytic reduction of chromium by poly(aniline-co-o-aminophenol): An efficient and recyclable way to remove Cr(VI) in wastewater

Poly(aniline-co-o-aminophenol) (PANOA)-modified glassy carbon electrode (GCE) was first used to investigate the electrocatalytic reduction of dichromate in a NaCl solution of pH 5.0. The results of cyclic voltammograms and UV–vis spectra demonstrated that the reduction of Cr(VI) occurred at PANOA-modified GCE. The FT-IR, ESR and XPS results showed that the Cr(VI) can be doped in the PANOA films and can convert to less-toxic Cr(III). The doping level Cr/N was 78.2% and trace amount of Cl (0.42%) was detected in the doped PANOA, which indicated that the doping process is effective and PANOA had rather good ion selectivity in the 0.10 M NaCl supporting electrolyte. The factors influenced the reduction were also considered. Various initial concentrations of Cr(VI) had different removal rates. The maximum removal rate of Cr(VI) at 20 mg L⁻¹ (32.3%) was better than that of at 5 mg L⁻¹ (22.9%). The solution pH had little effect on Cr(VI) reduction and doping process of the PANOA because PANOA had good electrochemical activity and stability in a wide range of pHs (from pH 4 to pH 8).     

Corrosion protection aspects of electrochemically synthesized poly(o-anisidine-co-o-toluidine) coatings on copper

The poly(o-anisidine-co-o-toluidine) coatings were synthesized on copper substrates by electrochemical copolymerization of o-anisidine with o-toluidine using sodium salicylate as supporting electrolyte. These coatings were characterized by cyclic voltammetry, UV-vis absorption spectroscopy, Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance spectroscopy (NMR) and scanning electron microscopy (SEM). The formation of the copolymer with the mixture of monomers in the aqueous sodium salicylate solution was ascertained by a critical comparison of the results obtained with the polymerization of the individual monomers, o-anisidine and o-toluidine, respectively. The corrosion protection aspects of poly(o-anisidine-co-o-toluidine) coatings to copper was investigated in aqueous 3% NaCl solution by potentiodynamic polarization technique and electrochemical impedance spectroscopy (EIS). The results of the potentiodynamic polarization measurements and EIS studies showed that the poly(o-anisidine-co-o-toluidine) coatings provided the effective corrosion protection to copper than that of respective homopolymers. The corrosion rate is observed to depend on the feed ratio of o-toluidine used for the synthesis of the copolymer coatings.     

Influence of electrochemically prepared poly(pyrrole-co-N-methyl pyrrole) and poly(pyrrole)/poly(N-methyl pyrrole) composites on corrosion behavior of copper in acidic medium

Poly(pyrrole-co-N-methyl pyrrole) copolymer and poly(pyrrole)/poly(N-methyl pyrrole) bilayer composites were electrochemically synthesized on copper by cyclic voltammetry from aqueous solution of 0.3 M oxalic acid and 0.1 M monomer. Synthesis of copolymers were performed with different monomer feed ratios (pyrrole:N-methyl pyrrole, 8:2, 6:4, 5:5, 4:6 and 2:8) and in order to determine the copolymer, which has the best corrosion performance, anodic polarization was applied to copolymer coated samples. It was found that the performance of coatings was strongly dependent to the monomer feed ratio and the copolymer synthesized with 8:2 concentration ratio showed the most protective property compared to others. Bilayer of poly(pyrrole)/poly(N-methyl pyrrole) was also synthesized to compare the anticorrosive properties. Polymer films were characterized by ATR-FTIR spectroscopy and SEM techniques. Corrosion behavior of polymer composites was investigated in 0.1 M H₂SO₄ solution by anodic polarization and electrochemical impedance spectroscopy. Different approaches such as phase angle at high frequency and areas under Bode plots were used to evaluate corrosion performances of the coatings. Copolymer and bilayer coatings were found to have higher protection effect than single polypyrrole coatings. Moreover, bilayer coating exhibited better protection efficiency than copolymer coating against corrosion of copper when the obtained results were compared.     

Electrochemical synthesis of poly(N-methylaniline) on an iron electrode and its corrosion performance

Synthesis of poly(N-methylaniline) (PNMA) on pure iron and Pt electrodes was carried out from aqueous 0.3 M oxalic acid solution containing 0.1 M N-methylaniline (NMA) by potentiodynamic and galvanostatic techniques. It was found that when compared to polyaniline (PAni) and its ring- and N-ethyl-substituted derivatives, PNMA can be electrosynthesized with lower upper scanning potential (upper potential limit, E_upp) of 0.8 V vs. saturated calomel electrode (SCE) on an Fe electrode. PNMA coatings were characterized by electrochemical, scanning electron microscopy (SEM) and FTIR techniques. Linear anodic potentiodynamic polarization results proved that increasing the acidity of the polymerization solution causes more effective protection against corrosion in 0.5 M H₂SO₄ medium for PNMA. Moreover, PNMA exhibited similar protective properties with PAni under the same corrosion test conditions. Tafel test results reveal that the PNMA coating appears to enhance protection for iron in 0.5 M NaCl and 0.1 M HCl solutions. According to EIS results, the PNMA coating is able to offer protection to Fe electrodes in NaCl compared to that in HCl medium over a long immersion period.     

Mobilities of charge carriers in poly(o-methylaniline) and poly(o-methoxyaniline)

Mobilities of charge carriers in poly(o-methylaniline) (PMA) and poly(o-methoxyaniline) (PMOA) films are electrochemically determined over a range of oxidation stages of the polymer films. In the low oxidation region, mobilities of both the polymers are comparable to that of polyaniline (PANI). In the high oxidation region, however, mobility values systematically decrease in the order of PANI > PMA > PMOA, showing that the bulky groups present at the ortho position play a more important role in the high oxidation region. The low mobilities of charge carriers in the high oxidation region explain why PMA and PMOA are less conducting than PANI.     

Electrochemical synthesis and characterization of poly(m-toluidine)

Poly(m-toluidine) was prepared by electrochemical polymerization of the corresponding monomer on gold and tin oxide electrodes, in acid medium. The polymer was characterized by elemental analysis, cyclic voltammetry,I-t curves and scanning electron microscopy. The utility of poly(m-toluidine) as an anion-exchange film is demonstrated on the basis of the electrostatic incorporation of anionic redox species into the poly(m-toluidine) film.     

Electrochemical preparation and kinetic study of poly(o-tolidine) in aqueous medium

Poly(o-tolidine), PoT, film was prepared by electrochemical oxidation of the monomer, oT, in 0.1 M HCl + 0.1 M KClO₄. The presence of KClO₄ in the formation medium was found to be essential for the electropolymerization process to proceed. Increasing the upper potential limit up to +1.5 V, instead of +1.0 V, leads to appearance of a new anodic peak at +1.36 V and enhancement of the polymer formation of PoT without changing the film structure. The electrochemical behavior of the formed polymer films was investigated in 1.0 M HClO₄. The kinetic parameters were calculated from the values of the charge consumed during the electropolymerization process. The rate of the polymerization reaction was found to depend on the concentration of the monomer rather than the electrolyte. The polymerization rate is first order with respect to the monomer concentration and zero order with respect to the electrolyte. The electrolyte plays no active role in the kinetics of the electropolymerization process and its role is most likely limited to polymer doping.     

Protective properties of polyaniline and poly(aniline-co-o-anisidine) films electrosynthesized on brass

Polyaniline and poly(aniline-co-o-anisidine) films were deposited on brass (Cu40Zn). The synthesis processes of homo and copolymer film were carried out under cyclic voltammetric condition from 0.12 M aniline and 0.06 M aniline + 0.06 M o-anisidine containing 0.2 M sodium oxalate solutions. Homo and copolymer films were characterized by scanning electron microscopy (SEM). SEM images clearly show that one of the brass electrodes was covered with a black copolymer film of strongly adherent homogeneous characteristic while the other one with a porous dark green homo polymer one. The corrosion performances of coated and uncoated electrodes in 3.5% NaCl were evaluated with the help of AC impedance spectroscopy, anodic polarization plots and open circuit potential–time curves. The protective effect of homo and copolymer films formed on brass grew in parallel with extended exposure time. It was only observed with copolymer-coated electrode that changes in the charge transfer resistance of copolymer-coated electrode were related to strong adsorption of copolymer film on the brass surface which led to the formation of a protective oxide layer due to its catalytic behaviour.     

Electrochemical and in situ TM-AFM studies of the polymerization conditions on poly(o-methoxyaniline) film morphology

The in situ atomic force microscopy and the electrochemical studies on electropolymerization of the o-methoxyaniline in the 0.0-0.8 V versus NHE range of the electrode potential are described. It is proved that in the 0.0-0.3 V versus NHE a redox process takes place, resulting in the formation of poly(o-methoxyaniline) in its reduced form, leucoemeraldine. The different morphologies are exhibited by poly(o-methoxyaniline) under different polymerization conditions. The microscopic results show that with the increase of the monomer concentration in the bulk of electrolyte solution the globular morphology, related to the coil like molecular structure, is replaced by the fibrilar one, related to the opened-up, more conductive extended coil structure. It is shown that oxidation of a leucoemeraldine state of polymer to its emeraldine state results in the change of the morphology from the chain like structure to the massive fibrilar like structure. The reduction of oxidized polymer results in its irreversible fragmentation.     

Electrochemical synthesis and characterization of poly(9-benzylfluorene)

In this study, we report the electrochemical polymerization of 9-benzylfluorene (9-BF) in acetonitrile solution. The characterization of the resulting poly(9-BF) film obtained on the working electrode has been performed by using attenuated total reflectance infrared spectroscopy. Besides electrochemical properties, the optical and photoluminescent properties of film were also investigated in detail by means of UV–Vis spectroscopy and fluorescence spectroscopy. Fluorescent spectral studies indicate that polymer film in solid state emits blue-green light at around 470/520 nm under irradiation of UV light. In addition, scanning tunneling microscopy was used to investigate the morphology of poly(9-BF) film. The morphological results also reveal that the surface of single crystalline gold electrode is completely covered with the polymer film.     

Corrosion protective poly(o-ethoxyaniline) coatings on copper

Poly(o-ethoxyaniline) (POEA) coatings were synthesized on copper (Cu) by electrochemical polymerization of o-ethoxyaniline in aqueous salicylate solution by using cyclic voltammetry. These coatings were characterized by cyclic voltammetry, UV-vis absorption spectroscopy, Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM). The performance of POEA as protective coating against corrosion of Cu in aqueous 3% NaCl was assessed by the potentiodynamic polarization technique and electrochemical impedance spectroscopy (EIS). The results of the potentiodynamic polarization and EIS studies demonstrate that the POEA coating has ability to protect the Cu against corrosion. The corrosion potential was about 0.330 V versus SCE more positive in aqueous 3% NaCl for the POEA coated Cu than that of uncoated Cu and reduces the corrosion rate of Cu almost by a factor of 140.     

Inhibition of steel corrosion by electrosynthesized poly(o-anisidine)-dodecylbenzenesulfonate coatings

Poly(o-anisidine)-dodecylbenzenesulfonate (POA-DBSA) coatings were synthesized on stainless steel from aqueous solution containing o-anisidine and dodecylbenzene sulfonic acid by using cyclic voltammetry. These coatings were characterized by Fourier transform infrared spectroscopy (FTIR), UV-vis absorption spectroscopy, scanning electron microscopy (SEM) and cyclic voltammetry (CV). Corrosion tests of these coatings were carried out in aqueous 3% NaCl solution by using open circuit potential (OCP) measurements, potentiodynamic polarization technique, cyclic potentiodynamic polarization measurements and electrochemical impedance spectroscopy (EIS). The results reveal that POA-DBSA acts as a corrosion protective coating on steel and reduces the corrosion rate (CR) of steel almost by a factor of 14.5.     

Novel indium(III) complexes with sterically hindered o-iminobenzoquinone

The first examples of indium(III) derivatives based on sterically hindered 4,6-di-tert-butyl-N-(2,6-di-iso-propylphenyl)-o-iminobenzoquinone (imQ) were synthesized and characterized in details. The interaction of sodium o-iminobenzosemiquinolate with indium(III) iodide produces bis[4,6-di-tert-butyl-N-(2,6-di-iso-propylphenyl)-o-iminobenzosemiquinonato]-iodo-indium(III) (1). The same product 1 was obtained by the reactions of imQ with InI or imQ disodium derivative with indium(III) iodide. The interaction of imQ with InI₃ results in the formation of indium(III) compound (2) containing neutral form of o-iminobenzoquinone ligand. Structures of complexes 1 and 2 were determined by X-ray diffraction analysis.     

Synthesis, characterization and degradation of poly(dl-lactide)-block-polyvinylpyrrolidone-block-poly(dl-lactide) copolymers

A new kind of A-B-A block copolymers with good biocompatibility and adjustable degradability was synthesized by ring-opening polymerization, in which DL-lactide polymerized and grew from the two ends of polyvinylpyrrolidone (PVP). The well-defined triblock structures of copolymers were characterized by GPC, ¹H NMR, FTIR and DSC. There were two pronounced glass transition temperatures which showed apparent microphase separations between hydrophilic PVP segment and hydrophobic poly(dl-lactide) (PDLLA) segments. The hydrolytic degradation of PDLLA and copolymers in phosphate buffer solution (PBS, pH = 7.4) showed that the degradation rate of copolymers apparently became faster in comparison with that of PDLLA homopolymer, and increased with increasing PVP content. The measurements through ¹H NMR and FTIR showed that the degraded fragments contained PDLLA oligomers, lactates and soluble chains composed of PVP blocks attached with short PDLLA ones.     

Potentiodynamic deposition of poly (o-anisidine-co-metanilic acid) on mild steel and its application as corrosion inhibitor

For the first time, poly (o-anisidine-co-metanilic acid) (PASM) was deposited on mild steel substrate by electrochemical polymerization of o-anisidine and metanilic acid monomers in aqueous solution of 0.1 M H₂SO₄. The electrochemical polymerization of o-anisidine takes place in the presence of metanilic acid monomer and uniform, strongly adherent coating was obtained on the substrate. The electroactivity of copolymer was studied by cyclic voltammetry and AC impedance techniques. There is an increasing anodic current due to oxidation of metanilic acid monomer at the surface of the electrode when the applied potential is cycled from −0.2 V to 0.8 V. These deposits were characterized by Fourier transform infrared (FTIR) spectroscopy, UV-vis and TG/DTA techniques. The effect of various concentrations of PASM copolymer solution in acid rain corrosive media has been studied through potentiodynamic polarization, AC impedance and I-E curve methods. The soluble form of polymeric solution provided better anti-corrosive behavior in artificial acid rain solution.     

Electrochemical synthesis of poly(ortho-ethoxyaniline) from phosphoric and sulphuric acid solutions

The growth and nucleation mechanism of poly(ortho-ethoxyaniline) (POEA) are investigated by cyclic voltammetry (CV) and potentiostatic technique. It was shown that growing of POEA is faster in sulphuric acid solution compared to phosphoric acid solution. Different rate trends were obtained with the increase of switching potential. From cyclic voltammograms, it is evident that the obtained polymer has a similar behaviour to the one reported for polyaniline, but there is a difference in position of current peaks, due to the electronic and steric effects of ethoxy-group. In presence of different anions, a different nucleation mechanism was obtained. In sulphuric acid solution nucleation proceeds through 3D instantaneous nucleation under diffusion control, and in phosphoric acid solution nucleation proceeds through 3D progressive nucleation under diffusion control.