Ethylene vinyl acetate/Mg‐Al LDH nanocomposites by solution blending

Partially exfoliated ethylene vinyl acetate (EVA‐40, 40% vinyl acetate content)/layered double hydroxide (LDH) nanocomposites using organically modified layered double hydroxide (DS‐LDH) have been synthesized by solution intercalation method. X‐ray diffraction (XRD) and transmission electron microscopy (TEM) studies of nanocomposites shows the formation of exfoliated LDH nanolayers in EVA‐40 matrix at lower DS‐LDH contents and partially intercalated/exfoliated EVA‐40/MgAl LDH nanocomposites at higher DS‐LDH contents. These EVA‐40/MgAl LDH nanocomposites demonstrate a significant improvement in tensile strength and elongation at break for 3 wt% of DS‐LDH filler loading compare to neat EVA‐40 matrix. Thermogravimetric analysis also shows that the thermal stability of the nanocomposites increases with DS‐LDH content in EVA‐40. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Rubber/LDH nanocomposites by solution blending

The rubber nanocomposites containing ethylene vinyl acetate (EVA) having 60 wt % of vinyl acetate content and organomodified layered double hydroxide (DS‐LDH) as nanofiller have been prepared by solution intercalation method and characterized. The XRD and TEM analysis demonstrate the formation of completely exfoliated EVA/DS‐LDH nanocomposites for 1 wt % filler loading followed by partially exfoliated structure for 5–8 wt % of DS‐LDH content. EVA/DS‐LDH nanocomposites show improved mechanical properties such as tensile strength (TS) and elongation at break (EB) in comparison with neat EVA. The maximum value of TS (5.1 MPa) is noted for 3 wt % of DS‐LDH content with respect to TS value of pure EVA (2.6 MPa). The data from thermogravimetric analysis show the improvement in thermal stability of the nanocomposites by ≈15°C with respect to neat EVA. Limiting oxygen index measurements show that the nanocomposites act as good flame retardant materials. Swelling property analysis shows improved solvent resistance behavior of the nanocomposites (1, 3, and 5 wt % DS‐LDH content) compared with neat EVA‐60. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of vinyl acetate content on the mechanical and thermal properties of ethylene vinyl acetate/MgAl layered double hydroxide nanocomposites

Ethylene vinyl acetate (EVA)/Mg‐Al layered double hydroxide (LDH) nanocomposites using EVA of different vinyl acetate contents (EVA‐18 and EVA‐45) have been prepared by solution blending method. X‐ray diffraction and transmission electron microscopic studies of nanocomposites clearly indicate the formation of exfoliated/intercalated structure for EVA‐18 and completely delaminated structure for EVA‐45. Though EVA‐18 nanocomposites do not show significant improvement in mechanical properties, EVA‐45 nanocomposites with 5 wt % DS‐LDH content results in tensile strength and elongation at break to be 25% and 7.5% higher compared to neat EVA‐45. The data from thermogravimetric analysis show that the nanocomposites of EVA‐18 and EVA‐45 have ≈10°C higher thermal decomposition temperature compared to neat EVA. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of ethylene vinyl acetate/Mg–Al layered double hydroxide nanocomposites

Mg–Al layered double hydroxide (LDH)/Ethylene vinyl acetate (EVA‐28) nanocomposites were prepared through solution intercalation method using organically modified layered double hydroxide (DS‐LDH). DS‐LDH was made by the intercalation of sodium dodecyl sulfate (SDS) ion. The structure of DS‐LDH and its nanocomposites with EVA‐28 was determined by X‐ray diffraction (XRD) and transmission electron microscope (TEM) analysis. XRD analysis shows that the original peak of DS‐LDH shifted to lower 2θ range and supports the formation of intercalated nanocomposites while, TEM micrograph shows the presence of partially exfoliated LDH nanolayers in addition to orderly stacked LDH crystallites in the polymer matrix. The presence of LDH in the nanocomposites has been confirmed by Fourier transform infrared (FTIR) analysis. The mechanical properties show significant improvement for the nanocomposite with respect to neat EVA‐28. Thermogravimetric (TGA) analysis shows that thermal stability of the nanocomposites is higher than that of EVA‐28. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1845–1851, 2007     

Synthesis and characterization of polyurethane/Mg‐Al layered double hydroxide nanocomposites

Layered double hydroxide (LDH) is a new type of nanofiller, which improves the physicochemical properties of the polymer matrix. In this study, 1, 3, 5, and 8 wt % of dodecyl sulfate‐intercalated LDH (DS‐LDH) has been used as nanofiller to prepare a series of thermoplastic polyurethane (PU) nanocomposites by solution intercalation method. PU/DS‐LDH composites so formed have been characterized by X‐ray diffraction and transmission electron microscopy analysis which show that the DS‐LDH layers are exfoliated at lower filler (1 and 3 wt %) loading followed by intercalation at higher filler (8 wt %) loading. Mechanical properties of the nanocomposite with 3 wt % of DS‐LDH content shows 67% improvement in tensile strength compared to pristine PU, which has been correlated in terms of fracture behavior of the nanocomposites using scanning electron microscope analysis. Thermogravimetric analysis shows that the thermal stability of the nanocomposite with 3 wt % DS‐LDH content is ≈ 29°C higher than neat PU. Limiting oxygen index of the nanocomposites is also improved from 19 to 23% in neat PU and PU/8 wt% DS‐LDH nanocomposites, respectively. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Thermoplastic polyurethane and nitrile butadiene rubber blends with layered double hydroxide nanocomposites by solution blending

Polymer blending coupled with nanofillers has been widely accepted as one of the cheaper methods to develop high‐performance polymeric materials for various applications. In the present work, dodecyl sulfate intercalated Mg? Al‐based layered double hydroxide (DS‐LDH) was used as nanofiller in the synthesis of polyurethane blended with nitrile butadiene rubber (PU/NBR; 1:1 w/w) nanocomposites, which were subsequently characterized. X‐ray diffraction (XRD) and transmission electron microscopy (TEM) confirmed the partial dispersion of Mg? Al layers in PU/NBR blends at lower filler content followed by aggregation at higher filler loading. In comparison to the neat PU/NBR blend, the tensile strength (156%) and elongation at break (21%) show maximum improvement for 1 wt% filler loading. The storage and loss moduli, thermal stability and limiting oxygen index of the nanocomposites are higher compared to the neat PU/NBR blend. Glass transition temperature and swelling measurements increase up to 3 wt% DS‐LDH loading in PU/NBR compared to either neat PU/NBR or its other corresponding nanocomposites. XRD and TEM analyses indicate the partial distribution of DS‐LDH in PU/NBR blends suggesting the formation of partially exfoliated nanocomposites. The improvements in mechanical, thermal and flame retardancy properties are much greater compared to the neat blend confirming the formation of high‐performance polymer nanocomposites. Copyright © 2009 Society of Chemical Industry     

Effect of layered silicate on EPDM/EVA blend nanocomposite: Dynamic mechanical,thermal, and swelling properties

Polymer blend nanocomposites have been developed by solution method using ethylene propylene diene terpolymer (EPDM), ethylene vinyl acetate (EVA‐45) copolymer, and organically modified layered silicate. Morphological investigation made by wide‐angle X‐ray diffraction and transmission electron microscopic analysis indicates intercalated structure of EPDM/EVA nanocomposites with partial disorder. Scanning electron microscopic studies exhibit the phase behavior of EPDM/EVA blend nanocomposites. Dynamic mechanical thermal analysis shows a significant increase in storage modulus in the rubbery plateau. The decrease in damping (tan δ) value and enhanced glass‐transition temperature (T_g) demonstrate the reinforcing effect of layered silicate in the EPDM/EVA blend matrix. The tensile modulus of these nanocomposites also showed a significant improvement with the filler content. The main chain scission of EPDM/EVA blend nanocomposites compared with the neat EPDM/EVA blend showed substantial improvement in thermal stability in nitrogen, whereas a sizeable increase is observed in air. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Ethylene propylene diene terpolymer/ethylene vinyl acetate/layered silicate ternary nanocomposite by solution method

A new ternary nanocomposite has been developed using ethylene propylene diene terpolymer (EPDM), ethylene vinyl acetate (EVA‐45) copolymer, and organically modified layered silicate (16 Me‐MMT) from sodium montmorillonite (Na⁺‐MMT). Wide angle X‐ray diffraction and transmission electron microscopic analysis confirmed the intercalation of the polymer chains in between the organosilicate layers and the nanoscale distribution of 16 Me‐MMT in polymer matrix, respectively. The measurement of mechanical properties for 2–8 wt% of 16 Me‐MMT loadings showed a significant increase in tensile strength, elongation at break, and modulus at different elongations. Such an improvement in mechanical properties has been correlated based on the fracture behavior of nanocomposite by SEM analysis. Thermal stability of EPDM/EVA/layered silicate ternary nanocomposites also showed substantial improvements compared with the neat EPDM/EVA blend, confirming thereby the formation of a high performance nanocomposite. POLYM. ENG. SCI., 46:437–843, 2006. © 2006 Society of Plastics Engineers     

Synthesis of silane‐grafted ethylene vinyl acetate copolymer and its application to compatibilize the blend of ethylene‐propylene‐diene copolymer and silicone rubber

Vinyltrimethoxysilane‐grafted ethylene vinyl acetate copolymer (EVA‐g‐VTMS) was synthesized and applied to compatibilize ethylene‐propylene‐diene copolymer (EPDM)/methyl vinyl silicone rubber (MVQ) blends. The silane‐grafting was successfully proved by differential scanning calorimetry, FTIR spectroscopy and XPS spectroscopy. The additive amount of the compatibilizer (EVA‐g‐VTMS) was optimized to be 10 phr (parts per hundred of rubber in weight) based on analysis of scanning electron microscopy, mechanical properties, aging properties, dynamic mechanical properties, rheological properties and thermal properties. Compared with the blend without EVA‐g‐VTMS, results show that the blend with 10 phr of EVA‐g‐VTMS exhibits the finest morphology. Tensile strength, elongation at break, modulus at 100% elongation, tear strength and TE index increase by 82.5%, 16.9%, 60.0%, 40.9%, and 41.9%, respectively. Dynamic mechanical analysis reveals storage modulus increase and glass transition temperatures of EPDM and MVQ move closer to each other. Rheological analysis shows a decrease in complex modulus and complex viscosity, and the processibility of the blend was improved. Furthermore, thermogravimetric analysis shows enhancement of thermal stability. POLYM. ENG. SCI., 2017. © 2017 Society of Plastics Engineers     

Synergistic effects of exfoliated LDH with some halogen‐free flame retardants in LDPE/EVA/HFMH/LDH nanocomposites

The synergistic effects of exfoliated layered double hydroxides (LDH) with some halogen‐free flame retardant (HFFR) additives, such as hyperfine magnesium hydroxide (HFMH), microencapsulated red phosphorus (MRP), and expandable graphite (EG), in the low‐density polyethylene/ethylene vinyl acetate copolymer/LDH (LDPE/EVA/LDH) nanocomposites have been studied by X‐ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), thermal analysis (TGA and DTG), mechanical properties, limiting oxygen index (LOI), and UL‐94 tests. The XRD results show that EVA as an excellent compatilizer can promote the exfoliation of LDH and homogeneous dispersion of HFMH in the LDPE/EVA/HFMH/LDH nanocomposites prepared by melt‐intercalation method. The TEM images demonstrate that the exfoliated LDH layers can act as synergistic compatilizer and dispersant to make the HFMH particles dispersed homogeneously in the LDPE matrix. The results from the mechanical, LOI, and UL‐94 tests show that the exfoliated LDH layers can also act as the nano‐enhanced and flame retardant synergistic agents and thus increase the tensile strength, LOI values, and UL‐94 rating of the nanocomposites. The morphological structures of charred residues observed by SEM give the positive evidence that the compact charred layers formed from the LDPE/EVA/HFMH/LDH nanocomposites with the exfoliated LDH layers play an important role in the enhancement of flame retardant and mechanical properties. The TGA and DTG data show that the exfoliated LDH layers as excellent flame retardant synergist of MRP or EG can apparently increase the thermal degradation temperature and the charred residues after burning. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effects of an intercalating agent on the morphology and thermal and flame‐retardant properties of low‐density polyethylene/layered double hydroxide nanocomposites prepared by melt intercalation

The effects of an intercalating agent on the morphology and thermal and flame‐retardant properties of low‐density polyethylene (LDPE)/layered double hydroxide (LDH) nanocomposites were studied with Fourier transform infrared spectroscopy, X‐ray diffraction, transmission electron microscopy, microscale combustion calorimetry, thermogravimetric analysis, and mechanical property measurements. X‐ray diffraction and transmission electron microscopy demonstrated that after intercalation with stearate anion (SA) or dodecyl sulfate anion (DS), organo‐LDH could be nanodispersed in an LDPE matrix with exfoliated structures or intercalated structures simultaneously with partially exfoliated structures, respectively, via melt intercalation. However, the unmodified LDH composites yielded only microcomposites. Microscale combustion calorimetry, thermogravimetric analysis, and dynamic Fourier transform infrared spectra showed the following order for the flame‐retardant and thermal properties: LDPE/SA‐modified LDH > LDPE/DS‐modified LDH > LDPE/NO₃‐modified LDH > LDPE. The higher performance of the LDPE/LDH nanocomposites with respect to flame retardance and thermal stability could be attributed to the better dispersion state of the LDH layers in the LDPE matrix and the greater hindrance effect of LDH layers on the diffusion of oxygen and volatile products throughout the composite materials when they were exposed to burning or thermal degradation. The tensile strength and elongation at break of the LDPE/LDH nanocomposites decreased to some extent because of the decrease in the crystallinity of the LDPE matrix. A transmittance test showed that the transparency of the exfoliated LDPE/SA‐modified LDH nanocomposite was very close to that of neat LDPE. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Properties and morphologies of elastomer blends modified with EPDM‐g‐poly[2‐dimethylamino ethylmethacrylate]

The graft copolymerization of 2‐dimethylamino ethylmethacrylate (DMAEMA) onto ethylene propylene diene mononer rubber (EPDM) was carried out in toluene via solution polymerization technique at 70°C, using dibenzoyl peroxide as initiator. The synthesized EPDM rubber grafted with poly[DMAEMA] (EPDM‐g‐PDMAEMA) was characterized with ¹H‐NMR spectroscopy, gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and thermal gravimetric analysis (TGA). The EPDM‐g‐PDMAEMA was incorporated into EPDM/butadiene acrylonitrile rubber (EPDM/NBR) blend with different blend ratios, where the homogeneity of such blends was examined with scanning electron microscopy and DSC. The scanning electron micrographs illustrate improvement of the morphology of EPDM/NBR rubber blends as a result of incorporation of EPDM‐g‐PDMAEMA onto that blend. The DSC trace exhibits one glass transition temperature (T_g) for EPDM/NBR blend containing EPDM‐g‐PDMAEMA, indicating improvement of homogeneity. The physico‐mechanical properties after and before accelerated thermal aging of the homogeneous, and inhomogeneous EPDM/NBR vulcanizates with different blend ratios were investigated. The physico‐mechanical properties of all blend vulcanizates were improved after and before accelerated thermal aging, in presence of EPDM‐g‐PDMAEMA. Of all blend ratios under investigation EPDM/NBR (75/25) blend possesses the best physico‐mechanical properties together with the best (least) swelling (%) in brake fluid. Swelling behavior of the rubber blend vulcanizates in motor oil and toluene was also investigated. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Natural rubber/poly(ethylene‐co‐vinyl acetate)‐blend‐based nanocomposites

Natural rubber (NR)/poly(ethylene‐co‐vinyl acetate) (EVA) blend–clay nanocomposites were prepared and characterized. The blend nanocomposites were prepared through the melt mixing of NR/EVA in a ratio of 40/60 with various amounts of organoclay with an internal mixer followed by compression molding. X‐ray diffraction patterns revealed that the nanocomposites formed were intercalated. The formation of the intercalated nanocomposites was also indicated by transmission electron microscopy. Scanning electron microscopy, used to study the fractured surface morphology, showed that the distribution of the organoclay in the polymer matrix was homogeneous. The tensile modulus of the nanocomposites increased with an increase in the organoclay content. However, an increase in the organoclay content up to 5 phr did not affect the tensile strength, but the organoclay reduced this property when it was increased further. This study also indicated that a low silicate content dispersed in the blend matrix was capable of increasing the storage modulus of the material. The addition of the organoclay also increased the decomposition temperature of the NR/EVA blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 353–362, 2006     

Preparation and properties of nano‐CaCO3/acrylonitrile‐butadiene‐styrene composites

CaCO₃/acrylonitrile‐butadiene‐styrene (ABS) and CaCO₃/ethylene‐vinyl acetate copolymer (EVA)/ABS nanocomposites were prepared by melting‐blend with a single‐screw extruder. Mechanical properties of the nanocomposites and the dispersion state of CaCO₃ particles in ABS matrix were investigated. The results showed that in CaCO₃/EVA/ABS nanocomposites, CaCO₃ nanoparticles could increase flexural modulus of the composites and maintain or increase their impact strength for a certain nano‐CaCO₃ loading range. The tensile strength of the nanocomposites, however, was appreciably decreased by adding CaCO₃ nanoparticles. The microstructure of neat ABS, CaCO₃/ABS nanocomposites, and CaCO₃/EVA/ABS nanocomposites was observed by scanning electron microscopy. It can be found that CaCO₃ nanoparticles were well‐dispersed in ABS matrix at nanoscale. The morphology of the fracture surfaces of the nanocomposites revealed that when CaCO₃/EVA/ABS nanocomposites were exposed to external force, nano‐CaCO₃ particles initiated and terminated crazing (silver streak), which can absorb more impact energy than neat ABS. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and characterization of exfoliated layered double hydroxide/silicone rubber nanocomposites

Silicone rubber (SR)/Mg–Al layered double hydroxide (LDH) nanocomposites were prepared by the solution intercalation of SR crosslinked by a platinum‐catalyzed hydrosilylation reaction into the galleries of dodecyl sulfate intercalated layered double hydroxide (DS–LDH). X‐ray diffraction and transmission electron microscopy analysis showed the formation of exfoliated structures of organomodified LDH layers in the SR matrix. The tensile strength and elongation at break of SR/DS–LDH (5 wt %) were maximally improved by 53 and 38%, respectively, in comparison with those of the neat polymer. Thermogravimetric analysis indicated that the thermal degradation temperature of the exfoliated SR/DS–LDH (1 wt %) nanocomposites at 50% weight loss was 20°C higher than that of pure SR. Differential scanning calorimetry analysis data confirmed that the melting temperature of the nanocomposites increased at lower filler loadings (1, 3, and 5 wt %), whereas it decreased at a higher filler loading (8 wt %). The relative improvements in the solvent‐uptake resistance behavior of the SR/DS–LDH nanocomposites were also observed. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Rubber–clay nanocomposite by solution blending

Ethylene vinyl acetate rubber (45% vinyl acetate content, EVA‐45) and organomodified clay (12Me‐MMT) composites were prepared by solution blending of the rubber and the clay. A combination of X‐ray diffraction, scanning electron microscopy, and transmission electron microscopy studies showed that the composites obtained are on the nanometer scale. The measurements of the dynamic mechanical properties for different compositions over a temperature range (?100 to +100°C) showed that the storage moduli of these rubber–clay nanocomposites are higher above the glass to rubber transition temperature compared to the neat rubber. The tensile strength of the nanocomposites is about 1.6 times higher than that of the EVA‐45. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 2216–2220, 2003     

Preparation and properties of in‐situ polymerized polyurethane/stearate intercalated layer double hydroxide nanocomposites

The present work deals with the effect of stearate intercalated layered double hydroxide (St‐LDH) loadings on the morphological, mechanical, thermal, adhesive and flame retardant properties of polyurethane (PU)/St‐LDH nanocomposites prepared by the in situ polymerization method. X‐ray diffraction and transmission electron microscopy studies confirmed that exfoliation takes place at 3 wt% loading followed by intercalation at higher filler loadings in the PU matrix. The exfoliated structure has been further verified by atomic force microscopy. The measurements of stress‐strain, thermogravimetric analysis, dynamic mechanical analysis, lap shear strength and peel strength analysis showed that the nanocomposites containing 3 wt% St‐LDH exhibit excellent improvement in tensile strength (ca 175%) and log storage modulus (ca 14%), while PU/St‐LDH (5 wt%) possesses optimum improvement in glass transition temperature (ca 6 °C), lap shear strength (200%) and peel strength (130%) over neat PU. In addition, the gradual improvements in limiting oxygen index value with St‐LDH loading indicated the higher effectiveness in providing better barrier properties as well as better flame retardant behavior. Copyright © 2012 Society of Chemical Industry     

Miscibility of blends of ethylene‐propylene‐diene terpolymer and polypropylene

The miscibility of polymers is not only an important basis for selecting a proper blending method, but it is also one of the key factors in determining the morphology and properties of the blends. The miscibility between ethylene‐propylene‐diene terpolymer (EPDM) and polypropylene (PP) was explored by means of dynamic mechanical thermal analysis, transmission electron microscopy (TEM), and differential scanning calorimetry (DSC). The results showed that a decrease in the PP content and an increase of the crosslinking density of EPDM in the EPDM/PP blends caused the glass‐transition temperature peaks of EPDM to shift from a lower temperature to higher one, yet there was almost no variance in the glass‐transition temperature peaks of PP and the degree of crystallinity of PP decreased. It was observed that the blends prepared with different mixing equipment, such as a single‐screw extruder and an open mill, had different mechanical properties and blends prepared with the former had better mechanical properties than those prepared with the latter. The TEM micrographs revealed that the blends were composed of two phases: a bright, light PP phase and a dark EPDM phase. As the crosslinking degree of EPDM increased, the interface between the phases of EPDM and PP was less defined and the EPDM gradually dispersed in the PP phase became a continuous phase. The results indicated that EPDM and PP were both partially miscible. The mechanical properties of the blends had a lot to do with the blend morphology and the miscibility between the blend components. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 315–322, 2002     

Structure and properties of polypropylene/clay nanocomposites compatibilized by solid‐phase grafted polypropylene

Polypropylene/organic‐montmorillonite (PP/OMMT) nanocomposites were prepared via a solid‐phase PP graft (TMPP) with a higher grafting level as the compatibilizer. The effects of the compatibilizer on the structure and properties of PP/OMMT nanocomposites were investigated. The structure of the nanocomposites were characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The results showed that when the weight ratio of TMPP and OMMT is greater than 1:1, the OMMT can be dispersed in PP matrix uniformly at the nanoscale. The mechanical properties of the nanocomposites reached a maximum when the weight ratio of TMPP and OMMT is 1:1, although more uniform dispersion was achieved at a higher content of TMPP. The mechanical properties of the nanocomposites decrease with the content of TMPP. The crystallization behavior, dynamic rheological property, and thermal stability of the nanocomposites were investigated by differential scanning calorimetry (DSC), dynamic rheological analysis, and thermal gravimetric analysis (TGA), respectively. Due to the synergistic effects of TMPP and OMMT on the crystallization of PP, the crystallization peak temperature of the nanocomposites increased remarkably compared with that of the neat PP. TMPP shows β‐phase nucleating ability and OMMT promotes the development of β‐phase crystallite. The nanocomposites show restricted melt flow and enhanced temperature sensitivity compared with the neat PP. The thermal stability of the nanocomposites is obviously improved compared with that of the neat PP. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers.     

Ethylene–propylene‐diene terpolymer/halloysite nanocomposites: Thermal,mechanical properties,and foam processing

Ethylene–propylene‐diene terpolymer (EPDM)/halloysite nanotube (HNT) nanocomposites were prepared by melt mixing in an internal mixer using a commercially available maleated semicrystalline EPDM and HNT. Transmission electron microscopy analysis of the EPDM/HNT composites revealed that the HNTs are uniformly dispersed at a nanometer scale in the matrix. Differential scanning calorimeter studies indicated that the HNT caused an increase in the nonisothermal crystallization temperature of the EPDM. Tensile and dynamic mechanical analysis exhibited that a small amount of the HNTs effectively enhanced the stiffness of the EPDM without adversely affecting its elongation‐at‐break. The EPDM/HNT nanocomposites were used to produce foams by using a batch process in an autoclave, with supercritical carbon dioxide as a foaming agent. The nanocomposite foams showed a smaller cell size and higher cell density as compared to the neat EPDM foam, and the nanocomposite with 10 phr HNT produced a microcellular foam with average cell size as small as 7.8 μm and cell density as high as 1.5 × 10¹⁰ cell/cm³. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40307.