Influence of fiber surface treatment on the properties of sisal-polyester composites

The effect of several chemical treatments, viz. organotitanate, zirconate, silane, and N-substituted methacrylamide, on the properties of sisal fibers used as reinforcement in unsaturated polyester resin (∼50 vol%) was investigated. An improvement in the properties was observed when sisal fibers were modified with surface treatments. Under humid conditions, a decrease of 30 to 44% in tensile and 50 to 70% in flexural strength has been noted. The strength retention of surface-treated composites (except silane) is high compared with untreated composites. It is observed that N-substituted methacrylamide-treated sisal composites exhibited better properties under dry as well as wet conditions. Fractographic evidence such as fiber breakage/splitting and matrix adherence on the pulled-out fiber surface explains such behavior.     

A Comparative Study on the Mechanical Properties of Jute and Sisal Fiber Reinforced Polymer Composites

The aim of the present study is to investigate and compare the mechanical properties of raw jute and sisal fiber reinforced epoxy composites with sodium hydroxide treated jute and sisal fiber reinforced epoxy composites. This is followed by comparisons of the sodium hydroxide treated jute and sisal fiber reinforced composites. The jute and sisal fibers were treated with 20% sodium hydroxide for 2 h and then incorporated into the epoxy matrix by a molding technique to form the composites. Similar techniques have been adopted for the fabrication of raw jute and sisal fiber reinforced epoxy composites. The raw jute and sisal fiber reinforced epoxy composites and the sodium hydroxide treated jute and sisal fiber reinforced epoxy composites were characterized by FTIR. The mechanical properties (tensile and flexural strength), water absorption and morphological changes were investigated for the composite samples. It was found that the sodium hydroxide treated jute and sisal fiber reinforced epoxy composites exhibited better mechanical properties than the raw jute and raw sisal fiber reinforced composites. When comparing the sodium hydroxide treated jute and sisal fiber reinforced epoxy composites, the sodium hydroxide treated jute fiber reinforced composites exhibited better mechanical properties than the latter.     

Unsaturated polyester‐toughened epoxy composites: Effect of sisal fiber on thermal and dynamic mechanical properties

In the present study, the mechanical and thermal properties of sisal fiber‐reinforced unsaturated polyester (UP)‐toughened epoxy composites were investigated. The sisal fibers were chemically treated with alkali (NaOH) and silane solutions in order to improve the interfacial interaction between fibers and matrix. The chemical composition of resins and fibers was identified by using Fourier‐transform infrared spectroscopy. The UP‐toughened epoxy blends were obtained by mixing UP (5, 10, and 15 wt%) into the epoxy resin. The fiber‐reinforced composites were prepared by incorporating sisal fibers (10, 20, and 30 wt%) within the optimized UP‐toughened epoxy blend. Scanning electron microscopy was used to analyze the morphological changes of the fibers and the adhesion between the fibers and the UP‐toughened epoxy system. The results showed that the tensile and flexural strength of (alkali‐silane)‐treated fiber (30 wt%) ‐reinforced composites increased by 83% and 55%, respectively, as compared with that of UP‐toughened epoxy blend. Moreover, thermogravimetric analysis revealed that the (alkali‐silane)‐treated fiber and its composite exhibited higher thermal stability than the untreated and alkali‐treated fiber systems. An increase in storage modulus and glass transition temperature was observed for the UP‐toughened epoxy matrix on reinforcement with treated fibers. The water uptake behavior of both alkali and alkali‐silane‐treated fiber‐reinforced composites is found to be less as compared with the untreated fiber‐reinforced composite. J. VINYL ADDIT. TECHNOL., 23:188–199, 2017. © 2015 Society of Plastics Engineers     

Sisal fibers treated with NaOH and benzophenonetetracarboxylic dianhydride as reinforcement of phenolic matrix

In this work, composites based on a phenolic matrix and untreated‐ and treated sisal fibers were prepared. The treated sisal fibers used were those reacted with NaOH 2% solution and esterified using benzophenonetetracarboxylic dianhydride (BTDA). These treated fibers were modified with the objective of improving the adhesion of the fiber–matrix interface, which in turn influences the properties of the composites. BTDA was chosen as the esterifying agent to take advantage of the possibility of introducing the polar and aromatic groups that are also present in the matrix structure into the surface of the fiber, which could then intensify the interactions occurring in the fiber–matrix interface. The fibers were then analyzed by SEM and FTIR to ascertain their chemical composition. The results showed that the fibers had been successfully modified. The composites (reinforced with 15%, w/w of 3.0 cm length sisal fiber randomly distributed) were characterized by SEM, impact strength, and water absorption capacity. In the tests conducted, the response of the composites was affected both by properties of the matrix and the fibers, besides the interfacial properties of the fiber–matrix. Overall, the results showed that the fiber treatment resulted in a composite that was less hygroscopic although with somewhat lower impact strength, when compared with the composite reinforced with untreated sisal fibers. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

高密度聚氨酯硬泡塑料／玻纤粉复合材料的研究

以聚醚多元醇、PAPI、催化剂、发泡剂和玻璃纤维等为原料,制备高密度聚氨酯硬泡及它与磨碎玻纤粉的复合材料。研究了不同密度硬泡的强度及磨碎玻纤粉粒径、预处理及其含量对复合材料强度的影响,不同复合材料的热稳定性。结果表明,随着密度的增加,硬泡的各种强度值总体上均呈逐渐增加趋势,其中500kg/m^3的聚氨酯的拉伸强度比200kg/m^3的提高了104．74％,冲击强度提高了194．84％;400目粒径的玻纤粉可使复合材料具有更高的拉伸强度、弯曲强度及压缩强度;玻纤的加入将降低材料的强度值,但偶联剂预处理可使它们有所改善;加入磨碎玻纤粉后,材料的热稳定性增加,且采用偶联剂KH550对玻纤粉进行预处理可进一步改善复合材料的耐热性能。     

表面处理对剑麻纤维布/不饱和树脂材料性能影响

采用碱、高锰酸钾及热对剑麻纤维布进行了表面处理,并由真空辅助树脂传递模塑成型(VARTM)工艺制备了剑麻纤维布增强不饱和聚酯树脂复合材料。通过对复合材料的力学性能及吸水性的测试,研究了不同剑麻纤维布表面处理对其不饱和聚酯树脂复合材料性能的影响。结果表明:经过碱处理,复合材料的拉伸、弯曲,冲击强度提高最大,可分别提高26.5%,16.5%和22.6%,吸水率降低了47.5%。对剑麻纤维布进行表面处理可使复合材料的界面性能得到改善,力学性能提高,吸水性降低。     

剑麻纤维及其复合材料研究进展

介绍了剑麻纤维(SF)的结构特点、物理力学性能以及纤维改性处理方法,从纤维形态及增强基质出发综述了长、短SF及SF混杂纤维增强复合材料以及SF增强热塑性、热固性树脂和弹性体复合材料方面的研究与开发,指出了SF增强复合材料今后的研究方向。     

Surface modification of sisal fibers: Effects on the mechanical and thermal properties of their epoxy composites

The aim of this paper is to evaluate the mechanical and thermal properties of sisal fiber reinforced epoxy matrix composites as a function of modification of sisal fiber by using mercerization and silane treatments. The changes introduced by the treatments on the chemical structure of sisal fibers have been analyzed by infrared spectroscopy (FTIR). Thermal behavior of both sisal fibers and composites has been studied by thermogravimetric analysis (TGA). Both treatments clearly enhanced thermal performance and also mechanical properties of fibers, being other physical properties also modified. Mercerization, above all when combined with silanization, led to significant enhancement on mechanical properties of composites as a consequence of increasing mechanical properties of fibers and improving fiber/matrix adhesion. POLYM. COMPOS., 26:121–127, 2005. © 2005 Society of Plastics Engineers     

An experimental and theoretical investigation of the compressive properties of multi-walled carbon nanotube/poly(methyl methacrylate) nanocomposite foams

Polymer nanocomposite foams are promising low density substitutes for nanocomposites. Carbon nanotube/polymer nanocomposite foams possess high strength, low density, and can be made conductive. Good control of foam properties is of great importance in the application of such materials. In the current study, multi-walled carbon nanotubes (MWNTs) with controlled aspect ratio were used to alter the foam morphology in MWNT/poly(methyl methacrylate) (PMMA) nanocomposite foams produced by a supercritical carbon dioxide (CO₂) foaming process. It was found that with the addition of one weight percent of MWNTs, the Young’s modulus of polymer foams increased by as much as 82%, and the collapse strength increased by as much as 104%. The influence of MWNT aspect ratio on the compressive properties of nanocomposite foams was investigated. The addition of MWNTs influenced the foam properties in two ways: improving the compressive properties of the solid matrix, and reducing the bubble size of the nanocomposite foams. A modified constitutive model for predicting the compressive properties of high density closed-cell polymer foams was developed. The influence of the bubble size on the mechanical properties of polymer foams was discussed based on the new model.     

剑麻/含红土聚乙烯基复合材料制备与性能

针对废旧地膜资源化利用过程中出现的高成本和低性能问题,本文提出了废旧地膜免清洗和剑麻纤维边角料增强的废旧地膜资源化利用技术。采用挤出造粒和注塑成型工艺,制备了剑麻边角料填充含红土废旧聚乙烯复合材料,分析了红土和剑麻纤维边角料对废旧地膜的填充作用。结果表明,红土颗粒使废旧地膜注塑试样的拉伸模量、硬度和耐热温度分别提高了34.4%、41.3%、和33.1%。红土颗粒难以和塑料基体形成良好的界面粘结,导致含红土废旧地膜注塑试样的拉伸强度、弯曲性能和冲击强度轻微降低,表明红土颗粒不能对废旧地膜进行增韧增强,但可以提高模量和耐热温度。剑麻纤维边角料对含红土废旧地膜具有明显的增强增韧作用,随着剑麻纤维添加量的增加,剑麻纤维填充的含红土废旧地膜复合材料的力学性能增加。剑麻纤维填充量超过一定值后,会在复合材料中引入气孔,同时会降低剑麻纤维的分散程度,出现剑麻聚集体,导致复合材料的力学性能降低。     

Bio‐composites for structural applications: Poly‐l‐lactide reinforced with long sisal fiber bundles

Fully bio‐based and biodegradable composites were compression molded from unidirectionally aligned sisal fiber bundles and a polylactide polymer matrix (PLLA). Caustic soda treatment was employed to modify the strength of sisal fibers and to improve fiber to matrix adhesion. Mechanical properties of PLLA/sisal fiber composites improved with caustic soda treatment: the mean flexural strength and modulus increased from 279 MPa and 19.4 GPa respectively to 286 MPa and 22 GPa at a fiber volume fraction of V_f = 0.6. The glass transition temperature decreased with increasing fiber content in composites reinforced with untreated sisal fibers due to interfacial friction. The damping at the caustic soda‐treated fibers‐PLLA interface was reduced due to the presence of transcrystalline morphology at the fiber to matrix interface. It was demonstrated that high strength, high modulus sisal‐PLLA composites can be produced with effective stress transfer at well‐bonded fiber to matrix interfaces. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40999.     

Evaluation of the mechanical properties of sisal–polyester composites as a function of the polyester matrix formulation

In this work a comparative study on the impact and tensile properties of polyester/sisal fiber reinforced composites was undertaken. The polyester matrix was used bare and modified with: (1) a silane coupling agent; (2) a flame retardant system; and (3) a blend of the silane agent and the flame retardant system. The experimental results show that the flame retardant acts as a particulate reinforcement to the polyester matrix and the silane coupling agent acts as a plasticizer. The simultaneous addition of these two compounds to the polyester resin tended to decrease the performance of the composites. The results obtained show that strength or toughness could be tailored, and although none of the composites manufactured with the modified polyester matrices showed a significant improvement on the fiber–matrix interface strength, a better compromise between impact and tensile properties was obtained with the silane modified matrix. The critical fiber volume fraction was also evaluated and shown to be less than 10% for the sisal–polyester composite investigated here. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1209–1217, 2004     

Behavior of sisal fiber concrete cylinders externally wrapped with jute FRP

The use of environmentally friendly natural fibers as building materials is benefit to achieve a sustainable construction. This article performs a study on the use of natural jute fibers as reinforcement of concrete and natural sisal fibers in fiber reinforced polymer (FRP) composites as concrete confinement, i.e., sisal fiber reinforced concrete (SFRC) composite column wrapped by jute FRP (JFRP) (SFRC‐JFRP). Uniaxial compression test was conducted to assess the compression performance of the composite columns as axial structural member. A total of 24 specimens were tested. The effects of JFRP wrapping thickness and sisal fiber inclusion on the compressive performance of the composite columns were investigated. Results indicate that JFRP confinement significantly increases the compressive strength and ductility of both PC and SFRC with an increase in JFRP thickness. Besides, the inclusion of sisal fiber further enhances the strength as well as the efficiency of confinement under uniaxial compression. Also, the models for ultimate strength and ultimate strain of PC‐JFRP and SFRC‐JFRP are proposed. POLYM. COMPOS., 38:1910–1917, 2017. © 2015 Society of Plastics Engineers     

Mechanical and dynamic mechanical properties of epoxy syntactic foams reinforced by short carbon fiber

Epoxy syntactic foams were prepared with diglycidyl ether of bisphenol‐A (DGEBA) epoxy resin, 2.4.6‐tri(dimethylaminomethyl)phenol (DMP‐30), coupling treated microsphere and short carbon fiber. The density of the foam was maintained between 0.56 and 0.91 g/cm³ for all compositions. Compressive, flexural, tensile and dynamic mechanical properties of the foams were investigated with respect to hollow glass microsphere (HGM) and carbon fiber (CF) content. A considerable improvement in the mechanical properties viz. compressive, flexural and tensile strengths was observed for the foams on incorporation of a small quantity of CF. The storage modulus were higher for the foam composites containing CF. The presence of HGM has significant influence on T_g of the syntactic foams, spherical filler diminished the T_g of the syntactic foams due to the plasticizing effect of the coupling treatment of HGM, that is helpful for enhancing damping properties of syntactic foams. POLYM. COMPOS., 37:1960–1970, 2016. © 2015 Society of Plastics Engineers     

Friction properties of sisal fiber/nano‐silica reinforced phenol formaldehyde composites

The friction‐resistant sisal fiber/nano‐silica phenol formaldehyde resin composites were prepared through compression molding. To enhance the bonding between the sisal fiber (SF) and polymer matrix, SF were treated with different surface modifiers. The worn surfaces of composites were observed by scanning electron microscope (SEM). The result shows that the matrix of nano‐silica phenol formaldehyde resin can relieve the heat fade of the friction materials. Meanwhile sisal fibers treated with borax have effectively improved the friction and wear properties of the composites when the fiber content was 15%. POLYM. COMPOS. 36:433–438, 2015. © 2014 Society of Plastics Engineers     

Preparation and characterization of EVA–sisal fiber composites

In this work, composites of an EVA polymer matrix and short sisal fiber were characterized. The physical‐morphological as well as chemical interactions between EVA and sisal were investigated. When the samples were prepared in the presence of dicumyl peroxide, the results suggest that crosslinking of EVA as well as grafting between EVA and the sisal fibers took place. Morphological changes were studied by scanning electron microscopy (SEM). Results from Hg‐porosimetry, SEM, Fourier transform infrared spectroscopy, surface free energy, and gel content strongly indicate grafting of EVA onto sisal under the composite preparation conditions, even in the absence of peroxide. The grafting mechanism could not be confirmed from solid‐state ¹³C NMR analysis. The grafting had an impact on the thermal and mechanical properties of the composites, as determined by differential scanning calorimetry and tensile testing. Thermogravimetric analysis results show that the composites are more stable than both EVA and sisal fiber alone. The composite stability, however, decreases with increasing fiber content. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1607–1617, 2006     

剑麻/钢纤维增强改性酚醛树脂力学和摩擦性能

采用改性酚醛树脂为基体,剑麻/钢纤维混杂为增强纤维,通过辊炼、模压成型工艺制备了剑麻/钢纤维增强酚醛树脂复合材料.研究了剑麻纤维的加入及含量对聚砜改性酚醛树脂复合材料力学性能、摩擦磨损性能及热稳定性能的影响.结果表明:剑麻纤维质量分数为15%、钢纤维为10%时,复合材料的冲击和弯曲强度分别为3.82 kJ/m2和59.6 Mpa,达到最大;随着剑麻纤维含量的增加,复合材料的摩擦系数降低,热稳定性能下降,当剑麻纤维质量分数为10%时,复合材料的摩擦性能优异;复合材料的磨损面呈现黏着磨损和疲劳磨损特征.     

Influence of fiber orientation and fiber content on properties of sisal‐jute‐glass fiber‐reinforced polyester composites

The incorporation of natural fibers with polymer matrix composites (PMCs) has increasing applications in many fields of engineering due to the growing concerns regarding the environmental impact and energy crisis. The objective of this work is to examine the effect of fiber orientation and fiber content on properties of sisal‐jute‐glass fiber‐reinforced polyester composites. In this experimental study, sisal‐jute‐glass fiber‐reinforced polyester composites are prepared with fiber orientations of 0° and 90° and fiber volume of sisal‐jute‐glass fibers are in the ratio of 40:0:60, 0:40:60, and 20:20:60 respectively, and the experiments were conducted. The results indicated that the hybrid composites had shown better performance and the fiber orientation and fiber content play major role in strength and water absorption properties. The morphological properties, internal structure, cracks, and fiber pull out of the fractured specimen during testing are also investigated by using scanning electron microscopy (SEM) analysis. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42968.     

Short sisal fiber‐reinforced tire rubber composites: Dynamic and mechanical properties

The world tendency toward using recycled materials demands new products from vegetable resources and waste polymers. In this work, composites made from powdered tire rubber (average particle size: 320 μm) and sisal fiber were prepared by hot‐press molding and investigated by means of dynamic mechanical thermal analysis and tensile properties. The effects of fiber length and content, chemical treatments, and temperature on dynamic mechanical and tensile properties of such composites were studied. The results showed that mercerization/acetylation treatment of the fibers improves composite performance. Under the conditions investigated the optimum fiber length obtained for the tire rubber matrix was 10 mm. Storage and loss moduli both increased with increasing fiber content. The results of this study are encouraging, demonstrating that the use of tire rubber and sisal fiber in composites offers promising potential for nonstructural applications. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 670–677, 2004     

An investigation of sound absorption coefficient on sisal fiber poly lactic acid bio‐composites

In this research, the mechanical, acoustical, thermal, morphological, and infrared spectral properties of untreated, heat and alkaline‐treated sisal fiber‐reinforced poly‐lactic‐acid bio‐composites were analyzed. The bio‐composite samples were fabricated using a hot press molding machine. The properties mentioned above were evaluated and compared with heat‐treated and alkaline‐treated sisal fibers. Composites with heat‐treated sisal fibers were found to exhibit the best mechanical properties. Thermo‐gravimetric analysis (TGA) was conducted to study the thermal degradation of the bio‐composite samples. It was discovered that the PLA‐sisal composites with optimal heat‐treated at 160°C and alkaline‐treated fibers possess good thermal stability as compared with untreated fiber. The results indicated that the composites prepared with 30wt % of sisal had the highest sound absorption as compared with other composites. Evidence of the successful reaction of sodium hydroxide and heat treatment of the sisal fibers was provided by the infrared spectrum and implied by decreased bands at certain wavenumbers. Observations based on scanning electron microscopy of the fracture surface of the composites showed the effect of alkaline and heat treatment on the fiber surface and improved fiber‐matrix adhesion. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42470.