A simple method for forecast of cooling time of high‐density polyethylene during gas‐assisted injection molding

Gas‐assisted injection molding (GAIM) is an innovative plastic processing technology, which was developed from the conventional injection molding, and has currently found wide industrial applications. About 70% of the whole gas‐assisted injection molding cycle is actually occupied by the cooling stage. The quality and production efficiency of molded parts are considerably affected by the cooling stage. Hence, it is necessary to study the solidification behaviors during the cooling stage. In this work, a simple experimental method was designed to simulate the solidification behaviors of high‐density polyethylene during cooling stage of GAIM. The enthalpy transformation approach, coupled with the control‐volume/finite difference techniques, was adopted to deal with the transient heat transfer problems with phase change effects. In situ measurements of the temperature decreases in the cavity were also carried out. Reasonable agreements between the experimental values and the simulated results such as cooling time, cooling rates, and temperature curves were obtained, which proved that this simple experimental method was effective. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Morphology of gas‐assisted and conventional injection molded polycarbonate/polyethylene blend

The skin‐core structure of the gas‐assisted and conventional injection molded polycarbonate (PC)/polyethylene (PE) blend was investigated. The results indicated that both the size and the shape of the dispersed PC phase depended not only on the nature of PC/PE blend and molding parameters, but also on its location in the parts. Although the gas‐assisted injection molding (GAIM) parts and conventional injection molding (CIM) part have the similar skin‐core structure, the morphology evolution of PC phase in the GAIM moldings and the CIM moldings showed completely different characteristics. In the section perpendicular to the melt flow direction, the morphology of the GAIM moldings included five layers, skin intermediate layer, subskin, core layer, core intermediate layer as well as gas channel intermediate layer, according to the degree of deformation. PC phase changed severely in the core layer of GAIM moldings, as well as in the subskin of CIM moldings. In GAIM parts, PC phase in the core layer of the nongate end changed far more intensely and aligned much orderly than that in the gate end. The morphology of PC phase in the GAIM part molded with higher gas pressure changed more severe than that in the GAIM part molded with lower gas pressure. In a word, PC phase showed more obvious fibrillation in the GAIM moldings than that in the CIM moldings. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3069–3077, 2006     

Extension of the orientation region of high density polyethylene molded by gas‐assisted injection molding: control of the thermal field

Wider zones with close‐knit orientation crystals in high density polyethylene (HDPE) parts prepared via the gas‐assisted injection molding (GAIM) process were obtained under high cooling gas pressure. In this study, compressed nitrogen, as a cooling medium, was introduced to retain a high cooling rate of the polymer melt. The high gas pressure leads to fast cooling of the polymer melt, which contributes to the stability of more oriented and stretched chains during the cooling stage. Then many more oriented structures are formed. SEM shows that many more oriented structures and interlocking shish‐kebab structures are achieved in parts under highest cooling gas pressure (P3). The P3 parts possess a higher degree of orientation than the corresponding regions of parts under lowest cooling gas pressure (P1). Moreover, tensile testing indicates that, compared with P1 parts, although P3 parts have lower crystallinity, the mechanical properties are improved because of the wider orientation zone and many more interlocking shish‐kebab structures. Combining the HDPE molecular parameters with the characteristics of the GAIM flow field and temperature field, the stability of oriented or stretched chains and the formation of orientation structures in various zones of the parts were analyzed. © 2014 Society of Chemical Industry     

Simulation of a mold‐cooling process for gas‐assisted injection molded parts designed with a top rib on the gas channel

The same CAE model used for the filling and packing stage in the gas‐assisted injection molding (GAIM) process simulation was also applied to simulate the cooling phase. This was made possible by using the line source method for modeling cooling channels. The cycle‐averaged and cyclic transient mold cavity surface temperature distribution within a steady cycle was calculated using the three‐dimensional modified boundary element technique similar to that used in conventional injection molding. The analysis results for GAIM plates of a semicircular gas channel design attached with a top rib are illustrated and discussed. It was found that the difference in cycle‐averaged mold wall temperatures may be as high as 10°C, and within a steady cycle, part temperatures may also vary by about 15°C. The conversion of the gas channel into equivalent circular pipe and further simplification into two‐node elements using the line source method not only affects the mold wall temperature calculation very slightly but also reduces the computer time by 93%. This indicates that it is feasible to achieve an integrated process simulation for GAIM under one CAE model, resulting in great computational efficiency for industrial application.     

Numerical prediction of phase‐change heat conduction of injection‐molded high density polyethylene thick‐walled parts via the enthalpy transforming model with mushy zone

Transient heat transfer problems with phase‐changes, also known as the “Stefan problems” or “moving‐boundary problems,” are practically significant in many engineering and technological fields. Injection molding, one of the most widely used plastics processing techniques, mainly consists of filling, packing, and cooling, and the cooling stage is crucial since it considerably affects the productivity and quality of the molded parts. Thus, solutions for transient phase‐change heat conduction problems during injection molding will be instructive. In this article, the enthalpy transforming scheme proposed by Cao and Faghri, which could handle the Stefan problems for generalized multidimensional phase‐change structures, is applied coupled with the control‐volume/finite‐difference techniques. Considering the polydispersity and hierarchical structures, the polymer extended phase change temperature range or mushy zone was included in the two‐dimensional enthalpy formulation to forecast the transient phase‐change heat conduction during the cooling stage for injection‐molded high density polyethylene (HDPE) parts. Experiments were performed and good agreement has been achieved, which reveals that the enthalpy transforming model gives good prediction, especially for the cooling analysis for the injection molding of thick‐walled parts of crystalline polymers. The understanding of the phase‐change heat conduction characteristics may facilitate the optimal designs of polymer injection molding process for industrial applications. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Analysis of a liquid‐assisted molding process for coating microchannels with an ultraviolet curable polymer

Injection molding can be altered to form hollow parts by partially pre‐filling a mold with polymer melt and then injecting a gas into the mold before cooling. The gas will core the center section and in the process force melt into the unfilled portions of the mold. This process is called gas‐assisted injection molding (GAIM) and is a thoroughly studied polymer processing technique. Liquid‐assisted molding follows the same principles as GAIM, except the coring fluid is a liquid of low viscosity. Liquid‐assisted molding of an ultraviolet (UV) curable polymer can be used to coat microchannels, the benefit of which being a smooth and circular cross‐section. Presented here are experiments of the controlled microchannel flow of a long, immiscible liquid thread through a viscous UV curable polymer. The roles of channel geometry and bubble velocity are discussed for square, rectangular, and circular microchannels. Finally, a quasi‐analytical model for calculating the Newtonian coating fluid thickness, when the coring fluid is driven by a constant pressure, was developed using the equation for Poiseuille‐like flow within a square channel. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Integrated simulations of structural performance,molding process,and warpage for gas‐assisted injection‐molded parts. III. Simulation of cyclic,transient variations in mold wall temperatures

Whether it is feasible to perform an integrated simulation for structural analysis, process simulation, as well as warpage calculation based on a unified CAE model for gas‐assisted injection molding (GAIM) is a great concern. In the present study, numerical algorithms based on the same CAE model used for process simulation regarding filling and packing stages were developed to simulate the cooling phase of GAIM considering the influence of the cooling system. The cycle‐averaged mold cavity surface temperature distribution within a steady cycle is first calculated based on a steady‐state approach to count for overall heat balance using three‐dimensional modified boundary element technique. The part temperature distribution and profiles, as well as the associated transient heat flux on plastic–mold interface, are then computed by a finite difference method in a decoupled manner. Finally, the difference between cycle‐averaged heat flux and transient heat flux is analyzed to obtain the cyclic, transient mold cavity surface temperatures. The analysis results for GAIM plates with semicircular gas channel design are illustrated and discussed. It was found that the difference in cycle‐averaged mold wall temperatures may be as high as 10°C and within a steady cycle, part temperatures may also vary ∼ 15°C. The conversion of gas channel into equivalent circular pipe and further simplified to two‐node elements using a line source approach not only affects the mold wall temperature calculation very slightly, but also reduces the computer time by 95%. This investigation indicates that it is feasible to achieve an integrated process simulation for GAIM under one CAE model, resulting in great computational efficiency for industrial application. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 339–351, 1999     

A 3‐D finite element model for gas‐assisted injection molding: Simulations and experiments

To gain a better understanding of the gas‐assisted injection molding process, we have developed a computational model for the gas assisted injection molding (GAIM) process. This model has been set up to deal with (non‐isothermal) three‐dimensional flow, in order to correctly predict the gas distribution in GAIM products. It employs a pseudo‐concentration method, in which the governing equations are solved on a fixed grid that covers the entire mold. Both the air downstream of the polymer front and the gas are represented by a fictitious fluid that does not contributeto the pressure drop in the mold. The model has been validated against both isothermal and non‐isothermal gas injected experiments. In contrast to other models that have been reported in the literature, our model yields the gas penetration from the actual process physics (not from a presupposed gas distribution). Consequently, it is able to deal with the 3‐D character of the process, as well as with primary (end of gas filling) and secondary (end of packing) gas penetration, including temperature effects and generalized Newtonian viscosity behavior.     

Gas‐assisted injection molded polypropylene: The skin‐core structure

In this article, gas penetration‐induced skin‐core structure of isotactic polypropylene(iPP), which is molded by gas‐assisted injection molding at different gas pressures, was investigated. For comparison, the counterpart was also molded by conventional injection molding (CIM) using the same processing parameters but without gas penetration. They were characterized via PLM, DSC, and SEM. And the crystal morphology at different gas pressures was principally concerned. For the GAIM parts, highly oriented structure is formed in the skin zone, and much less oriented structure in the inner zone (near the gas channel surface). Furthermore, it is suggested that the naked shish structure can be developed in the skin zone of GAIM part, which is molded at higher gas pressures, and shish‐kebab structure is mainly formed in the skin zone of that, which is molded at lower gas pressure. However, for the CIM part, from the skin to the core zone, the dominant morphological feature is spherulite. In a word, the presence of gas penetration notably enhances the oriented structure formation and gives rise to the skin‐core structure. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Crystallization behavior and molecular orientation of high density polyethylene parts prepared by gas‐assisted injection molding

The dependence of hierarchy in crystalline structures and molecular orientations of high density polyethylene parts with different molecular weights molded by gas‐assisted injection molding (GAIM) was intensively examined by scanning electron microscopy, two‐dimensional wide‐angle X‐ray scattering as well as dynamic rheological measurements. The non‐isothermal crystallization kinetics of the samples were also analyzed with a differential scanning calorimeter at various scanning rates. It was found that oriented lamellar structure, shish‐kebab and common spherulites were formed in different regions of the GAIM samples. The scanning electron microscope observations were consistent with the two‐dimensional wide‐angle X‐ray scattering results and showed that the molecular chains near the mold wall had strong orientation behavior, revealing the distribution of the shear rate of the GAIM process. The differences in crystal morphologies can be attributed to molecular weight differences as well as their responses to the external fields during the GAIM process. The formation mechanism of the shish‐kebab structure under the flow field of GAIM was also explored. Copyright © 2012 Society of Chemical Industry     

Hierarchical crystalline structure of HDPE molded by gas-assisted injection molding

To understand the crystalline morphology of the parts molded by gas-assisted injection molding (GAIM), in this work, the hierarchical structures and the crystalline morphology of gas-assisted injection molded high-density polyethylene (HDPE) were investigated. According to the comparison between the results of the GAIM part and those of the conventional injection molded counterpart, it is found that gas penetration can remarkably enhance the shear rate during GAIM process and oriented lamellar structure, shish-kebab structure and common spherulites arise in the skin, subskin and gas channel region, respectively, owing to the different shear rate in these regions. Meanwhile, cooling rate also plays an important role in the formation of the oriented crystalline structure.     

The influence of processing parameters on fingering formation in fluid‐assisted injection‐molded disks

One of the problems encountered in fluid‐assisted injection‐molded parts is the gas or water “fingering” phenomenon, in which gas (water) bubbles penetrate nonuniformly into the core of the parts and form finger‐shape branches. Severe fingerings can lead to significant reductions in part stiffness. This study investigated the fingering phenomenon in fluid‐assisted injection‐molded disk parts. Experiments were carried out on a reciprocating injection‐molding machine equipped with gas‐ and water‐injection units. The material used was virgin polypropylene. A disk cavity with two different thicknesses was used for all experiments. The effects of various processing parameters on the fingering were examined. It was found that the melt short shot size and mold temperature were the principal parameters affecting the formation of part fingerings. In addition, the formation mechanism of part fingerings has also been proposed to better understand the formation of part fingerings. It has been shown that the fluid‐assisted filling process is an unstable system by nature. Any small perturbation by material viscosity or by temperature gradient can trigger the unbalance of gas (water) penetrations in the parts and result in fingerings. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Water‐assisted injection molding of thermoplastic materials: Effects of processing parameters

The objective of this study was to experimentally investigate the effects of various processing parameters on the water‐assisted injection molding of thermoplastic materials. Experiments were carried out on a lab‐developed water‐assisted injection molding system, which included a water pump, a water injection pin, a water tank equipped with a temperature regulator, and a control circuit. Two types of water injection pins designs were proposed to mold the parts. After molding, the lengths of water penetration in molded parts were measured. The effects of different processing parameters on the lengths of water penetration were determined. It was found that the shrinkage rate and the viscosity of the polymeric materials, and the void shapes of the hollowed cores mainly determined the water‐penetration lengths in molded products. In addition, a comparison has been made between the parts molded by water assisted injection molding and gas‐assisted injection molding. It was found that water‐assisted injection molded parts exhibit less uniform void sizes along the water channel. The cycle time for water‐assisted injection molded parts was shorter than that of conventional injection molded parts and gas‐assisted injection molded parts.     

Birefringence in gas‐assisted tubular injection moldings: Simulation and experiment

The influence of the processing variables on the birefringence and polymer/gas interface distribution is analyzed for polystyrene moldings obtained by gas‐assisted injection molding (GAIM) under various processing conditions. The processing variables studied were: melt and mold temperatures, shot size, gas pressure, injection speed, and gas‐delay time. Measurements and viscoelastic simulations of the radial distribution of birefringence components, Δn and n_rr ? n_θθ, the variation of the average birefringence, 〈n_zz ? n_θθ〉, along the molding and polymer/gas interface along the length of spiral‐shaped tubular moldings are presented. The polymer/gas interface distribution and flow stresses were simulated using a numerical scheme based on a hybrid finite element/finite difference/control volume method. The birefringence was calculated from the flow‐induced stresses using the stress‐optical rule. Simulations qualitatively agreed with measurements and correctly described theeffect of the processing variables on the birefringence andthe polymer/gas interface distribution in GAIM moldings. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Gas assisted injection molding of a handle: Three‐dimensional simulation and experimental verification

Methods implemented in a three‐dimensional finite element code for the simulation of gas assisted injection molding are described, and predictions compared with the results of molding trials. The emphasis is on prediction of primary gas penetration and plastic wall thickness, including the effects of cooling during a delay before gas injection. For the latter, time dependent heat transfer coefficients at the cavity surface are used, determined in a separate analysis of transient heat conduction through the plastic and the mold tool to the circulating coolant. This shows how the initial value of 25,000 W/m²K falls by about an order of magnitude during the first few seconds of cooling, and also how values vary from cycle to cycle as steady periodic conditions are approached. For a tubular handle molded in polystyrene, with melt flow modeled by a Cross WLF model, comparisons of simulations with sectioned parts show excellent prediction of wall thickness and its variation circumferentially and in bends. The increase in wall thickness due to cooling during a gas delay is accurately modeled, as is the occurrence of a blow out. POLYM. ENG. SCI. 45:1049–1058, 2005. © 2005 Society of Plastics Engineers     

Tailoring the crystalline morphologies and mechanical properties of high‐density polyethylene parts by a change in the fluid flow pattern under gas‐assisted injection molding

In this study, an increase in the cooling rate of high‐density polyethylene parts was carried out via a change in the fluid flow pattern to introduce gas cooling under a gas‐assisted injection‐molding process; this was conducive to the retention of orientation chains shaped during the injection stage and further developed into much more oriented crystals. Morphological observation showed that the parts without gas cooling (WOGC) were composed of oriented crystals except the gas channel zone, whereas the parts with gas cooling (WGC) were full of oriented crystals, especially much more interlocking shish‐kebab structures in the subskin zone. The WGC parts had a higher degree of orientation than the corresponding zone of the WOGC parts. Although the lower crystallinity, the wider orientation regions, and much more interlocking shish‐kebab structures led to considerable increases from 32 and 990 MPa in the WOGC parts to 36 and 1150 MPa in the WGC parts for the yield strength and elastic modulus, respectively. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40349.     

The influence of gas‐assisted injection molding parameters on the structure and thermomechanical properties of hollow parts

The purpose of the work was to estimate an influence of gas‐assisted injection conditions (the temperature of plastic material, switch time‐delay time, gas injection time) of shape, position and dimension of gas channel, and structure of injection molded parts. The change in the value of the dynamic Young modulus and the mechanical loss tangent in function of temperature and oscillation frequency by the dynamic mechanical thermal analysis (DMTA) method was determined. It was found that injection molding parameters: injection molding temperature, switching time and gas injection time influenced significantly mass, wall thickness, and thermomechanical properties of parts. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

气体辅助注射成型模拟中的CAD／CAE模型转换方法

给出了实现气体辅助注射成型ＣＡＥ技术的理论方法和重要算法过程,研究了气辅助注射成型过程中由气辅注塑件ＣＡＤ模型向其ＣＡＥ模型转换、保证几何模型的无缝传递和数据完备性的过程和方法。结果表明,这一技术可以为气体辅助注射成型模拟构造复杂的几何分析模型,得到高质量的单元网格和求解精度。