Numerical simulation of configuration and catalyst-layer effects on micro-channel steam reforming of methanol

A micro-reactor with eight non-parallel channels is proposed to improve the performance of micro-channel steam reforming of methanol. The widths of some channels in the micro-reactor vary gradually along the reactor length direction. The Zn-Cr/CeO₂-ZrO₂ catalyst is coated in the reformer with a certain porosity and permeability. The effects of micro-reactor structures and catalyst-coated manners on several factors are studied, including temperature distributions, velocity distributions, reactant concentrations and the methanol conversion rate. The results indicate that such a structure with a certain entrance inclination angle and channel inclination angle guarantees flow distribution uniformity in each reforming channel. Flow distribution uniformity is conducive to the increase of the methanol conversion rate. Besides, in order to measure strengths and weaknesses of different catalyst-coated manners, a wall-coated reformer and a packed-bed reformer are studied respectively. It is found that compared to the packed-bed reformer, the temperature and the methanol conversion rate in wall-coated reformer are far higher. It is necessary to find an optimal catalyst thickness that is able to reduce the CO concentration because the catalyst thickness can affect CO concentration in the product gases indirectly. The optimal inclination angles and the catalyst thickness are proposed based on the simulating results.     

Numerical simulation and experimental study of hydrogen production from dimethyl ether steam reforming in a micro-reactor

To enhance the heat and mass transfer during dimethyl ether (DME) steam reforming, a micro-reactor with catalyst coated on nickel foam support was designed and fabricated. A two-dimensional numerical model with SIMPLE algorithm and finite volume method was used to investigate 1) the fluid flow, 2) the heat transfer and 3) chemical reactions consist of DME hydrolysis, methanol steam reforming, methanol decomposition and water gas shift reactions. Both the numerical and the experimental results showed that the DME conversion in the micro-reactor is higher than that in the fixed bed reactor. The numerical study also showed that the velocity and the temperature distribution were more uniform in the micro-reactor. Wall temperature, porosity and steam/DME ratio have been investigated in order to optimize the process in the micro-reactor. The wall temperature of 270 °C and the steam/DME feed ratio of 5 were recommended. Meanwhile the results indicate that a larger porosity will give a higher DME conversion and CO concentration.     

Analysis of phase change heat transfer with annulus 1 kW class methanol steam reforming reaction under high-pressure operation

A fuel cell air independent propulsion (AIP) system of underwater vehicle requires a hydrogen storage system. The methanol steam reforming system is a candidate of hydrogen storage which can produce hydrogen from chemical reaction. Different from reforming system for station fuel cell system, the methanol steam reformer (MSR) for underwater vehicle requires high-pressure operation.Since the longitudinal temperature uniformity is a core parameter of conversion efficiency of steam reforming system, this study is focused on computational analysis of phase change heat transfer through the annulus for methanol steam reforming reaction. The annulus MSR using phase change material was developed to improve the temperature uniformity. The simulation model is verified with safety and performance analysis code (SPACE). The performance parameters of MSR were flow arrangement, steam to carbon ratio (SCR), and gas hourly space velocity (GHSV). The results were analyzed in terms of the hydrogen yield, heat flux, liquid mass flow rate, and methanol conversion rate. The flow arrangement varied the methanol conversion rate to a minor extent of approximately 0.1% because wall temperature was maintained uniformly. In the case of SCR, the hydrogen yield at SCR 2.5 was 0.637 (dry basis), which was the highest yield rate. Also, if GHSV was increased, hydrogen yield decreased from 0.690 (dry basis) to 0.527 (dry basis). The heat transfer pattern was also analyzed and it was found that steam is interactively condensed along with the progress of the reforming reaction.     

A study of methanol steam reforming on distributed catalyst bed

Heterogeneous catalytic fixed bed usually suffers from severe limitations of mass and heat transfer. These disadvantages limit reformers to a low efficiency of catalyst utilization. Three catalyst activity distributions have been applied to force the reactor temperature profile to be near isothermal operation for maximization of methanol conversion. A plate-type reactor has been developed to investigate the influence of catalyst activity distribution on methanol steam reforming. Cold spot temperature gradients are observed in the temperature profile along the reactor axis. It has been experimentally verified that reducing cold spot temperature gradients contributes to the improvement of the catalytic hydrogen production. The lowest cold spot temperature gradient of 3 K is obtained on gradient catalyst distribution type A. This is attributed to good characteristics of local thermal effect. Low activity at the reactor inlet with gradual rise along with the reactor flow channel forms the optimal activity distribution. Hydrogen production rate of 161.3 L/h is obtained at the methanol conversion of 93.1% for the gradient distribution type A when the inlet temperature is 543 K.     

Mathematical modeling of hydrogen production using methanol steam reforming in the coupled membrane reactor when the output materials of the reformer section is used as feed for the combustion section

Hydrogen is one of the most abundant elements on Earth's surface. It is not in nature in its pure form, but it can produce by various methods such as methanol steam reforming, partial oxidation, electrolysis, etc. In the present study, using the mass and energy conservation law, hydrogen production in coupled membrane reactors has been modeled using the methanol steam reforming process using two different methods in the coupled membrane reactor. A separate (fresh) methanol is used as feed for the combustion section in the first method. While in the second method, the reformer reactor's output material is used as feed for the combustion section. After simplifying using the required assumptions, the governing equations solved using the ode45 (shooting method) numerical method using MATLAB software. The results of this study show that the conversion of methanol in the coupled membrane reactor when separate methanol is used as feed in the combustion reactor, while in the same reactor, the output material of the reformer section used as feed in the combustion section, is 92% and 88.5% respectively. In this study, the effect of different parameters on the methanol conversion rate is investigated. Finally, it found that with increasing temperature and pressure and decreasing membrane thickness in coupled membrane reactors, methanol conversion rate increases. The percentage of hydrogen recovery in the two coupled membrane reactors is almost equal to 92%.     

A transient study of double-jacketed membrane reactor via methanol steam reforming

A non-isothermal unsteady-state model was established to simulate methanol steam reforming using a double-jacketed Pd membrane reactor. At steady state, a self-sustained membrane reactor was achieved by the oxidation of residual methanol and hydrogen from reformer for endothermic steam reforming. The molar fractions of species and reformer temperature were analyzed under co-current operation between oxidation and reformer sides. The start-up of reformer was simulated under two conditions: (1) The catalyst temperature was lower than the influent temperature and (2) The catalyst temperature was higher than influent temperature. Condition 1 yielded higher methanol conversion and reformer temperature than condition 2 at steady state. Moreover, the instability of species can be minimized on condition 1 during start-up. The fluctuation of membrane reactor at steady state was also studied. Two strategies were compared to analyze the reformer response when temporary extra hydrogen was required. The results showed that increasing inlet methanol outperformed increasing reformer temperature.     

Performance enhancement of methanol reforming reactor through finned surfaces and diffused entry for on-board hydrogen generation

Hydrogen-rich combustion in engines helps in reducing pollutants significantly. But hydrogen usage on a moving vehicle is not getting large-scale user acceptance mainly due to its poor energy storage density resulting in shorter driving ranges. This storage issue led to the hunt for mediums that can efficiently produce on-board hydrogen. Methanol proves to be an efficient alcohol fuel for producing hydrogen through steam reforming reaction. The heat energy required for such endothermic reaction is obtained through exhaust engine waste energy and this process is collectively known as thermochemical recuperation. However, the conventional reactor used for this process faces a lot of problems in terms of efficiency and methanol conversion. In this study, an attempt has been made to improve the design of the reactor for on-board hydrogen generation using engine exhaust heat for addressing the challenges related to performance and hydrogen yield. For enhancing the heat transfer, a finned surface (straight & wavy) was introduced in the reactor which resulted in an increment in methanol conversion significantly. It was found that wavy fin improved the methanol conversion up to 96.8% at an exhaust inlet temperature of 673 K. Also, a diffusing inlet section was introduced to increase the residence time of reactant gases while passing through the catalyst zone. Under given inlet conditions, the methanol conversion for 6° diffuse inlet reactor goes up to 87.9% as compared to 75.4% for the conventional reactor.     

Comparison between 1D and 2D numerical models of a multi-tubular packed-bed reactor for methanol steam reforming

The hydrogen-rich gas produced in-situ by methanol steam reforming (MSR) reactions significantly affects the performance and endurance of the high-temperature polymer electrolyte membrane (HT-PEM) fuel cell stack. A numerical study of MSR reactions over a commercial CuO/ZnO/Al₂O₃ catalyst coupling with the heat and mass transfer phenomena in a co-current packed-bed reactor is conducted. The simulation results of a 1D and a 2D pseudo-homogeneous reactor model are compared, which indicates the importance of radial gradients in the catalyst bed. The effects of geometry and operating parameters on the steady-state performance of the reactor are investigated. The simulation results show that the increases in the inlet temperature of burner gas and the tube diameter significantly increase the non-uniformity of radial temperature distributions in reformer tubes. Hot spots are formed near the tube wall in the entrance region. The hot-spot temperature in the catalyst bed rises with the increase in the inlet temperature of burner gas. Moreover, the difference in simulation results between the 1D and 2D models is shown to be primarily influenced by the tube diameter. With a methanol conversion approaching 100% or a relatively small tube diameter, the simplified 1D model can be used instead of the 2D model to estimate the reactor performance.     

Hydrogen production by steam reforming of dimethyl ether and CO-PrOx in a metal foam micro-reactor

A bi-function catalyst containing CuZnAlCr and HZSM-5 was used to generate hydrogen by stream reforming of dimethyl ether (SRD) in a metal foam micro-reactor and a fix-bed reactor. Dimethyl ether conversion of 99% and hydrogen yield of >95% was reached with HZSM-5/CuZnAlCr (mass ratio of 1:1) in the micro-reactor. A suitable balance between the dimethyl ether hydrolysis and methanol reforming steps requires the proper acidity and the metal sites. The CuZnAlCr/HZSM-5 properties, effect of CuZnAlCr to HZSM-5 mass ratio were investigated in the metal foam micro-reactor. Moreover, CO was removed from hydrogen-rich gas by preferential oxidation reaction (CO-PrOx) with PtFe/γ-Al₂O₃ catalyst in a similar metal foam micro-reactor follows the SRD stage. With the optimized O₂/CO ratio and reaction temperature, the CO concentration dropped to <10 ppm and hydrogen yield of ∼90% were achieved in the new-type SRD-COPrOx system. The SRD-COPrOx system provide a constant hydrogen production with CO concentration lower than 10 ppm during 20 h. The results indicate that metal foam micro-reactor has the great potential in the DME steam reforming to supply hydrogen for low-temperature fuel cells.     

Methanol steam reforming in a planar wash coated microreactor integrated with a micro-combustor

A numerical simulation of methanol steam reforming in a microreactor integrated with a methanol micro-combustor is presented. Typical Cu/ZnO/Al₂O₃ and Pt catalysts are considered for the steam reforming and combustor channels respectively. The channel widths are considered at 700 μm in the baseline case, and the reactor length is taken at 20 mm. Effects of Cu/ZnO catalyst thickness, gas hourly space velocities of both steam reforming and combustion channels, reactor geometry, separating substrate properties, as well as inlet composition of the steam reforming channel are investigated. Results indicate that increasing catalyst thickness will enhance hydrogen production by about 68% when the catalyst thickness is increased from 10 μm to 100 μm. Gas space velocity of the steam reforming channel shows an optimum value of 3000 h⁻¹ for hydrogen yield, and the optimum value for the space velocity of the combustor channel is calculated at 24,000 h⁻¹. Effects of inlet steam to carbon ratio on hydrogen yield, methanol conversion, and CO generation are also examined. In addition, effects of the separating substrate thickness and material are examined. Higher methanol conversion and hydrogen yield are obtained by choosing a thinner substrate, while no significant change is seen by changing the substrate material from steel to aluminum with considerably different thermal conductivities. The produced hydrogen from an assembly of such microreactor at optimal conditions will be sufficient to operate a low-power, portable fuel cell.     

Reforming of methanol with steam in a micro-reactor with Cu–SiO2 porous catalyst

In the present work, we report the results of a series of experiments for the hydrogen production via steam reforming of methanol with Cu–SiO₂ porous catalyst coated on the internal walls of a micro-reactor with parallel micro-passages. The catalyst was prepared by coating copper and silica nanoparticles on the internal surface of the microchannel via convective flow boiling heat transfer, followed by a calcination procedure at 973 K and therefore, the catalyst does not require any supportive material, which in turn reduced the complexity and cost of the preparation. The experiments were conducted at reactant flow rates of 0.1–0.9 lit/min, operating temperatures of 523–673 K, catalyst loading of 0.25 gr to 1.25 gr and at heat flux value of 500 kW/m². Results of the experiments showed that the methanol conversion can reach 97% at catalyst loading of 1.25 gr. It was also found that with an increase in the gas hourly space velocity (GHSV) of the reactants, the methanol conversion decreases, which was attributed to the decrease in the residence time, the suppression in diffusion of reactants into the pores of the catalyst, and also the decrease in the average film temperature of the reactor. The highest methanol conversion was obtained at gas hourly space velocity of 24,000 ml/(gr.hr) and T = 773 K and for molar ratio of methanol to water of 0.1. The molar ratio of methanol to water also influenced the thermal response of the reactor such that the surface temperature profile of the micro-reactor was more decreased at low methanol/water molar ratios.     

Experiments on hydrogen production from methanol steam reforming in the microchannel reactor

The entire experiments were conducted for microchannel methanol steam reforming, by which, the selection of catalyst, the operating parameters and the configuration of microchannels were discussed thoroughly. It was found that the higher the Cu concentration is, the more the corresponding active surface area of Cu will be, thereby improving the catalytic activity. The Cu-to-Zn ratio in Cu/ZnO/Al₂O₃ catalyst should be set at 1:1. The impacts of reaction temperature, feed flow rate, mixture temperature, and H₂O-to-CH₃OH molar ratio on the methanol conversion rate were also revealed and discussed. Characteristics of micro-reactors with various microchannels, including that 20 mm and 50 mm in length, as well as non-parallel microchannels, were investigated. It was found that the increase of microchannel length can improve the methanol conversion rate significantly. Besides, non-parallel microchannels help to maintain flow and temperature distribution uniformity, which can improve the performance of micro-reactor. In the present experiments, the presence of CO was under the condition that the methanol conversion rate was above 70%.     

Modeling a counter-current moving bed for fuel and steam reactors in the TRCL process

A mathematical model for the moving bed is developed to simulate the fuel and steam reactor in the TRCL (Three-Reactor Chemical-Looping) process. An ideal plug flow of the solid and gas is assumed in modeling the fuel and steam reactor in the TRCL process. The model considered the mass, heat balances, equilibrium, physical properties, such as the heat capacity and viscosity, and kinetics. From this model, the temperature, gas conversion and solid conversion profiles can be predicted for fuel and steam reactors. The oxygen carrier inventory (the mass of the oxygen carrier) in the fuel and steam reactor was calculated with variation of the solid inlet temperature, solid conversion, Fe₂O₃ content and steam feed rate. The temperature of the oxygen carrier to the reactor was the most sensitive parameter for determining the required inventory of the oxygen carrier. An increase in the solid inlet temperature was predicted to decrease the required inventory of the oxygen carrier. In the steam reactor, a solid inlet temperature increase over 1150 K will cause an increase in the inventory of the oxygen carrier due to the equilibrium conversion. An excessively low or high active material content will require a larger inventory of the oxygen carrier in the fuel reactor. In this study, approximately 20 wt.% of the Fe₂O₃ content was suitable for reducing the inventory of the oxygen carrier while achieving a solid conversion of 0.9 in the fuel reactor.     

A performance study of methanol steam reforming in an A-type microchannel reactor

The methanol steam reforming (MSR) performance in a microchannel reactor is directly related to the flow pattern design of the microchannel reactor. Hydrogen production improvements can be achieved by optimal design of the flow pattern. In this study, an A-type microchannel reactor with a flow pattern design of one inlet and two outlets was applied to conduct the MSR for hydrogen production. The MSR performance of the A-type microchannel reactor was investigated through numerical analysis by establishing a three-dimensional simulation model and compared with that of the conventional Z-type microchannel reactor. Experiments were also conducted to test the MSR performance and validate the accuracy of the simulation model. The results showed that compared with the conventional Z-type microchannel reactor, the species distributions in the A-type microchannel reactor were more homogeneous. In addition, compared with the Z-type microchannel reactor, the A-type microchannel reactor was shown to effectively increase the methanol conversion rate by up to 8% and decrease the pressure drop by about 20%, regardless of a slightly higher CO mole fraction. It was also noted that with various quantities of microchannels and microchannel cross sections, the A-type microchannel reactor was still more competitive in terms of a higher methanol conversion rate and a lower pressure drop.     

Flow structure of subcooled boiling flow in an internally heated annulus

Local measurements of flow parameters were performed for vertical upward subcooled boiling flows in an internally heated annulus. The annulus channel consisted of an inner heater rod with a diameter of 19.1 mm and an outer round pipe with an inner diameter of 38.1 mm, and the hydraulic equivalent diameter was 19.1 mm. The double-sensor conductivity probe method was used for measuring local void fraction, interfacial area concentration, and interfacial velocity. A total of 11 data were acquired consisting of four inlet liquid velocities, 0.500, 0.664, 0.987 and 1.22 m/s and two inlet liquid temperatures, 95.0 and 98.0 °C. The constitutive equations for distribution parameter and drift velocity in the drift-flux model, and the semi-theoretical correlation for Sauter mean diameter, namely, interfacial area concentration, which were proposed previously, were validated by local flow parameters obtained in the experiment.     

生物油-甲醇催化重整制氢的氢产率及碳转化率的研究

采用生物油-甲醇催化重整制氢。在微型固定反应装置上通过正交法试验设计,对生物油甲醇混合比例、反应温度、水碳比、进样流速等因素进行了系统的试验。在选择的最佳反应条件下,氢气产率和碳转化率分别为34.89%及63.34%。     

Enhancement of hydrogen reaction in a micro-channel by catalyst segmentation

The paper addresses the combustion characteristics of multi-segment catalysts in a micro-reactor by numerical simulation with detailed heterogeneous and homogeneous chemistries. The effect of multi-segment catalyst is delineated in terms of different catalyst dispositions, different flow conditions and different reactor properties. With a fixed total catalyst length (1 cm), multi-segment catalyst reveals better performance than single catalyst. The space between catalyst segments reduces the inhibition of homogeneous reactions by catalyst and promotes homogeneous reactions in this region since the neighboring catalysts help to maintain a high wall temperature. Therefore, homogeneous combustion can shift upstream with the multi-segment catalyst. The results of different catalyst dispositions show that more catalyst segments has better performance but the catalyst space distance has no obvious effects due to the fast reaction rate of hydrogen. For different flow conditions, the results indicate multi-segment catalyst disposition has better conversion ratio even though there is no homogeneous combustion in the fluid region for fuel-lean condition. The results for different inlet velocities show that multi-segment catalyst has no obvious benefit on lower inlet velocity. However, it can extend the blowout velocity. Finally different reactor dimension and wall material are simulated. Although heterogeneous reactions strengthen in small channel, multi-segment catalyst still has obvious benefit. The results of different wall thermal conductivity do not have obvious difference for multi-segment catalyst. These results can be used in the design of a catalytic micro-reactor for hydrogen/air reactions.     

Mathematical simulation of hydrogen production via methanol steam reforming using double-jacketed membrane reactor

The hydrogen production and purification via methanol reforming reaction was studied in a double-jacketed Pd membrane reactor using a 1-D, non-isothermal mathematical model. Both mass and heat transfer behavior were evaluated simultaneously in three parts of the reactor, annular side, permeation tube and the oxidation side. The simulation results exhibited that increasing the volumetric flow rate of hydrogen in permeation side could enhance hydrogen permeation rate across the membrane. The optimum velocity ratio between permeation and annular sides is 10. However, hydrogen removal could lower the temperature in the reformer. The hydrogen production rate increases as temperature increases at a given Damköhler number, but the methanol conversion and hydrogen recovery yield decrease. In addition, the optimum molar ratio of air and methanol was 1.3 with three air inlet temperatures. The performance of a double-jacketed membrane reactor was compared with an autothermal reactor by judging against methanol conversion, hydrogen recovery yield and production rate. Under the same reaction conditions, the double-jacketed reactor can convert more methanol at a given reactor volume than that of an autothermal reactor.     

Simultaneous production of two types of synthesis gas by steam and tri‐reforming of methane using an integrated thermally coupled reactor: mathematical modeling

In this work, tri‐reforming and steam reforming processes have been coupled thermally together in a reactor for production of two types of synthesis gases. A multitubular reactor with 184 two‐concentric‐tubes has been proposed for coupling reactions of tri‐reforming and steam reforming of methane. Tri‐reforming reactions occur in outer tube side of the two‐concentric‐tube reactor and generate the needed energy for inner tube side, where steam reforming process is taking place. The cocurrent mode is investigated, and the simulation results of steam reforming side of the reactor are compared with corresponding predictions for thermally coupled steam reformer and also conventional fixed‐bed steam reformer reactor operated at the same feed conditions. This reactor produces two types of syngas with different H₂/CO ratios. Results revealed that H₂/CO ratio at the output of steam and tri‐reforming sides reached to 1.1 and 9.2, respectively. In this configuration, steam reforming reaction is proceeded by excess generated heat from tri‐reforming reaction instead of huge fired‐furnace in conventional steam reformer. Elimination of a low performance fired‐furnace and replacing it with a high performance reactor causes a reduction in full consumption with production of a new type of synthesis gas. The reactor performance is analyzed on the basis of methane conversion and hydrogen yield in both sides and is investigated numerically for various inlet temperature and molar flow rate of tri‐reforming side. A mathematical heterogeneous model is used to simulate both sides of the reactor. The optimum operating parameters for tri‐reforming side in thermally coupled tri‐reformer and steam reformer reactor are methane feed rate and temperature equal to 9264.4 kmol h^?1 and 1100 K, respectively. By increasing the feed flow rate of tri‐reforming side from 28,120 to 140,600 kmol h^?1, methane conversion and H₂ yield at the output of steam reforming side enhanced about 63.4% and 55.2%, respectively. Also by increasing the inlet temperature of tri‐reforming side from 900 to 1300 K, CH₄ conversion and H₂ yield at the output of steam reforming side enhanced about 82.5% and 71.5%, respectively. The results showed that methane conversion at the output of steam and tri‐reforming sides reached to 26.5% and 94%, respectively with the feed temperature of 1100 K of tri‐reforming side. Copyright © 2013 John Wiley & Sons, Ltd.     

Enhancing efficiency of hydrocarbons to synthesis gas conversion in a counterflow moving bed filtration combustion reactor

An improvement is considered for the partial oxidation conversion of hydrocarbon gases to synthesis gas in a continuous non-premixed filtration combustion reactor with inert solid granular material flowing countercurrently to the gas flow. The reactor is supplemented with an additional heat exchanger, wherein the second reactant gas is preheated prior to supply to the middle part of the reactor. The composition of the gaseous products self-consistent with the temperature of combustion are assessed using approximation of established thermodynamic equilibrium in the products. The parametric domain for major control parameters, namely oxygen-to-fuel supply ratio, granular solid flowrate, and steam supply rate providing highly efficient conversion is determined. Calculations for the POX conversion of methane and a model biogas composition (50% methane, 40% carbon dioxide, 10% nitrogen) with air and steam are provided as examples. The calculations show that the process gives a possibility to substantially improve energy efficiency and provides a flexibility to control hydrogen yield through steam supply. The process provides a high chemical efficiency of conversion even with air used as an oxidant for conversion of low-caloric gases.