6?10 GHz ultra-wideband CMOS LNA

A two-stage matched ultra-wideband CMOS low noise amplifier (LNA) is presented. The LNA is designed to achieve a low noise figure with high voltage gain. The LNA fabricated in a 0.13 mum CMOS process shows a 3.9 dB average noise figure with a 27 dB voltage gain in the 6-10 GHz frequency band with a power consumption of 14 mW.     

Design of Low Power 2.4GHz CMOS Cascode LNA with Reduced Noise Figure for WSN Applications

In this paper, a narrowband cascode Low Noise Amplifier (LNA) with shunt feedback is proposed. A typical inductively degenerated cascode LNA can be treated as a Common Source-Common Gate (CS-CG) two stage LNA. The series interstage inductance is connected between CS-CG stages to increase the power gain. An additional inductance which is connected at the gate of CG stage is used to cancel out the parasitic capacitance of CG stage therefore reduces the noise figure of CG stage. The shunt feedback is used to improve the stability and input impedance matching. This configuration provides better input matching, lower noise figure, low power consumption and good reverse isolation. The proposed LNA exhibits the gain of 13 dB, input return loss of ?11 dB, noise figure of 2.2 dB and good reverse isolation of ?42.8 dB at a frequency of 2.4GHz using TSMC 0.13 μm CMOS technology. It produces gain and noise figure better than conventional cascode LNA. The proposed LNA is biased in moderate inversion region for achieving sufficient gain with low power consumption of 1.5mW at a supply voltage of 1.5V.     

用于IEEE802．11b／g WLAN直接下变频接收机的射频前端设计

介绍了一种应用于IEEE802．11b／g无线局域网接收机射频前端的设计。基于直接下变频的系统架构。接收机集成了低噪声放大器、I／Q下变频器、去直流偏移滤波器、基带放大器和信道选择滤波器。电路采用TSMC0．18μm CMOS工艺设计,工作在2．4GHz ISM（工业、科学和医疗）频段,实现的低噪声放大器噪声系数为0．84dB,增益为16dB,S11低于-15dB,功耗为13mW;I／Q下变频器电压增益为2dB,输入1dB压缩点为-1 dBm,噪声系数为13dB,功耗低于10mw。整个接收机射频前端仿真得到的噪声系数为3．5dB,IIP3为-8dBm,IP2大于30dBm,电压增益为31dB,功耗为32mW。     

A dual mode 2.4-GHz CMOS low noise amplifier employing body biasing

This paper presents a dual mode CMOS low noise amplifier (LNA) suitable for Worldwide Interoperability for Microwave Access applications, at 2.4?GHz. The design concept is based on body biasing. An off chip Digital to Analog Converter is used to generate the proper body bias voltage to control the LNA gain and linearity. Measurement results show that in the high gain mode, for V _BS?=?0.3?V, the cascode LNA, implemented in a 0.13???m CMOS standard process, exhibits a 14?dB power gain, a 3.6?dB noise figure (NF) and ?4.6?dBm of third order intercept point (IIP3) for a 4?mA current consumption under 1?V supply. Tuning V _BS to ?0.55?V, switches the LNA into the low gain mode. It achieves 8.6?dB power gain, 6.2?dB NF and 6?dBm IIP3 under a constrained power consumption of 1.7?mW.     

1.8GHz 0.35mm CMOS低噪声放大器的实现

介绍了一种频率为1.8GHz的低噪声放大器(LNA)的设计方案,采用TSMC 0.35μm CMOS工艺实现,增益为25dB,噪声系数2.56dB,功耗≤10mW,IIP3为-25dB或5dBm。     

0.5 V ultra-low power wideband LNA with forward body bias technique

An ultra-low power wideband CMOS low noise amplifier (LNA) fabricated in TSMC 0.18 μm RF CMOS process for sub 1 GHz applications is presented. The capacitive cross-coupled LNA with forwardbody- bias (FBB) technique is adopted to achieve wideband input impedance matching and low power, low noise factor. The LNA is tested in the frequency range of 400?900 MHz, and exhibits a voltage gain of 18.5?20.7 dB, and a noise figure of 2.95 dB, drawing only 0.385 mW from 0.5 V power supply.     

A 0.6-V Low Power UWB CMOS LNA

This paper presents the design of a low-power ultra-wideband low noise amplifier in 0.18-mum CMOS technology. The inductive degeneration is applied to the conventional distributed amplifier design to reduce the broadband noise figure under low power operation condition. A common-source amplifier is cascaded to the distributed amplifier to improve the gain at high frequency and extend the bandwidth. Operated at 0.6V, the integrated UWB CMOS LNA consumes 7mW. The measured gain of the LNA is 10dB with the bandwidth from 2.7 to 9.1GHz. The input and output return loss is more than 10dB. The noise figure of the LNA varies from 3.8 to 6.9dB, with the average noise figure of 4.65dB. The low power consumption of this work leads to the excellent figure of gain-bandwidth product (GBP) per milliwatt     

5.6GHz CMOS低噪声放大器设计

分析了一种射频COMS共源-共栅低噪声放大器的设计电路,采用TSMC 90nm低功耗工艺实现。仿真结果表明:在5.6GHz工作频率,电压增益约为18.5dB;噪声系数为1.78dB;增益1dB压缩点为-21.72dBm;输入参考三阶交调点为-11.75dBm。在1.2V直流电压下测得的功耗约为25mW。     

Low-power and low NF V-band down-converter in 0.13 μm CMOS

A V-band down-converter integrating a LNA and mixer in 0.13 mm CMOS technology is presented. The LNA has a current re-use topology for low power consumption. The transistor size of the LNA is optimised by the substrate noise for the low noise figure (NF) and f_max for high gain performance. The new resistive mixer for low LO power operation is proposed. The NF of the down-converter is 4.7 dB. The conversion gain and input P_1dB are 0.67 dB and 212.5 dBm, respectively. The proposed circuit, consuming only 11.6 mW, shows the lowest NF and highest linearity among V-band down-converters.     

Linearization technique using bipolar transistor at 5 GHz low noise amplifier

A CMOS low noise amplifier (LNA) used in wireless communication systems, such as WLAN and CDMA, must have low noise figure, high linearity, and sufficient gain. Several techniques have been proposed to improve the linearity of CMOS LNA circuits. The proposed low noise amplifier achieves high third-order input intercept point (IIP3) using multi-gated configuration technique, by using two transistors, the first is the main CMOS transistor, and the second is bipolar transistor in TSMC 0.18 m technology. Bipolar transistor is used to cancel the third-order component from MOS transistor to fulfill high linearity operation. This work is designed and fabricated in TSMC 0.18 m CMOS process. At 5 GHz, the proposed LNA achieves a measurement results as 16 dBm of IIP3, 10.5 dB of gain, 2.1 dB of noise figure, and 8 mW of power consumption.     

A low power high gain UWB LNA in 0.18-μm CMOS

A low power high gain differential UWB low noise amplifier (LNA) operating at 3-5 GHz is presented.A common gate input stage is used for wideband input matching; capacitor cross coupling (CCC) and current reuse techniques are combined to achieve high gain under low power consumption. The prototypes fabricated in 0.18-μm CMOS achieve a peak power gain of 17.5 dB with a -3 dB bandwidth of 2.8-5 GHz, a measured minimum noise figure (NF) of 3.35 dB and -12.6 dBm input-referred compression point at 5 GHz, while drawing 4.4 mA from a 1.8 V supply. The peak power gain is 14 dB under a 4.5 mW power consumption (3 mA from a 1.5 V supply). The proposed differential LNA occupies an area of 1.01 mm~2 including test pads.     

Design method for broadband CMOS RF LNA

A design method for a broadband RF CMOS low noise amplifier (LNA) is presented. The shape of the transfer function fits the classical filtering response such as Butterworth or Tchebycheff. This method uses an input matching cell with only parallel LC resonators coupled with admittance inverters realised by series coupling capacitors. An LNA for the 7.2 to 8.6 GHz frequency band designed with this method in a 0.13 /spl mu/m RF CMOS process shows a 3.9 dB noise figure with a voltage gain of 28 dB at 8 GHz with a power consumption of 3.9 mW and a surface consumption of 0.4 mm/sup 2/.     

A novel noise optimization technique for inductively degenerated CMOS LNA

This paper proposes a novel noise optimization technique. The technique gives analytical formulae for the noise performance of inductively degenerated CMOS low noise amplifier (LNA) circuits with an ideal gate inductor for a fixed bias voltage and nonideal gate inductor for a fixed power dissipation, respectively, by mathematical analysis and reasonable approximation methods. LNA circuits with required noise figure can be designed effectively and rapidly just by using hand calculations of the proposed formulae. We design a 1.8 GHz LNA in a TSMC 0.25 pan CMOS process. The measured results show a noise figure of 1.6 dB with a forward gain of 14.4 dB at a power consumption of 5 mW, demonstrating that the designed LNA circuits can achieve low noise figure levels at low power dissipation.     

5.7 GHz low-power variable-gain LNA in 0.18 /spl mu/m CMOS

A variable-gain low-noise amplifier (LNA) suitable for low-voltage and low-power operation is designed and implemented in a standard 0.18 /spl mu/m CMOS technology. With a current-reused topology, the common-source gain stages are stacked for minimum power dissipation while achieving high small-signal gain. The fully integrated 5.7 GHz LNA exhibits 16.4 dB gain, 3.5 dB noise figure and 8 dB gain tuning range with good input and output return losses. The LNA consumes 3.2 mW DC power from a supply voltage of 1 V. A gain/power quotient of 5.12 dB/mW is achieved in this work.     

Ultra-wideband CMOS low noise amplifier

A two-stage ultra-wideband CMOS low noise amplifier (LNA) is proposed. The first stage is optimised for wideband input matching and low noise figure, while the second stage is optimised to extend the -3 dB bandwidth of the overall amplifier. The combination of stages can provide lower noise figure and wider bandwidth simultaneously over that of previously reported feedback-based CMOS amplifiers. The implemented LNA shows a peak gain of 13.5 dB, more than 8.5 dB of input return loss, and a noise figure of 2.5-7.4 dB over a -3 dB bandwidth from 2 to 9 GHz with DC power consumption of 25.2 mW.     

低功耗CMOS低噪声放大器的分析与设计

基于TSMC 0.18μm CMOS工艺,设计了一种低功耗约束下的CMOS低噪声放大器。与传统的共源共栅结构相比,该电路在共源晶体管的栅源间并联一个电容,以优化噪声;并引入一个电感,与级间寄生电容谐振,以提高增益;通过减小晶体管的尺寸,实现了低功耗。模拟结果表明,在2.45 GHz工作频率下,增益大于14 dB,噪声系数小于1 dB,直流功耗小于2 mW。     

一种5~6 GHz宽带全集成CMOS低噪声放大器

采用55 nm标准CMOS工艺,设计并流片实现了一种应用于Wi-Fi 6(5 GHz)频段的宽带全集成CMOS低噪声放大器(LNA)芯片,包括源极退化共源共栅放大器、负载Balun及增益切换单元。在该设计中,所有电感均为片上实现;采用Balun负载,实现信号的单端转差分输出;具备高低增益模式,以满足输入信号动态范围要求。测试结果表明,在高增益模式下该放大器的最大电压增益为20.2 dB,最小噪声系数为2.2 dB;在低增益模式下该放大器的最大电压增益为15 dB,最大输入1 dB压缩点为-3.2 dBm。芯片核心面积为0.28 mm²,静态功耗为10.2 mW。     

A sub-1-dB NF±2.3-kV ESD-protected 900-MHz CMOS LNA

A sub-1-dB noise figure HBM ESD-protected [-3 kV, 2.3 kV] low noise amplifier (LNA) has been integrated in a 0.35-μm RF CMOS process with on-chip inductors. The sensitivity of the LNA performances to the spread of parasitics associated with package and bondwire has been attenuated by using an inductive on-chip source degeneration. At 920 MHz and P_dc=8.6 mW, the LNA features: noise figure NF=1 dB, input return loss=-8.5 dB, output return loss=-27 dB, power gain G _p=13 dB, input IIP3=-1.5 dBm. At a power dissipation of 5 mW and 17.6 mW, a NF respectively equal to 1.2 dB and 0.85 dB is measured. The CMOS LNA takes 12 pins of a TQFP48 package, an area of 1.0×0.66 mm² (bondwire pads excluded) and it is the first HBM ESD-protected [-3 kV, 2.3 kV] CMOS LNA to break the 1-dB NF barrier     

3.6~4.7GHz低噪声放大器

以一种经典的窄带低噪声放大器结构为基础,分析级联放大器的S参数,通过优化元件参数,获得了一种在3.6~4.7 GH z范围内具有低输入回波损耗、低噪声系数的放大器。采用标准的0.18μm RF CM O S工艺进行了设计和实现。芯片面积为0.6 mm×1.5 mm。测试结果表明:在3.6~4.7 GH z的范围内,该宽带低噪声放大器输入回波损耗小于-14 dB;噪声系数小于2.8 dB,增益大于10 dB。在1.8 V电源下功耗约为45 mW。     

A 5.7-GHz 0.18-/spl mu/m CMOS gain-controlled differential LNA with current reuse for WLAN receiver

This letter presents a 5.7 GHz 0.18 /spl mu/m CMOS gain-controlled differential LNA for an IEEE 802.11a WLAN application. The differential LNA, fabricated with the 0.18 /spl mu/m 1P6M standard CMOS process, uses a current-reuse technology to increase linear gain and save power consumption. The circuit measurement is performed using an FR-4 PCB test fixture. The LNA exhibits a noise figure of 3.7 dB, linear gain of 12.5 dB, P/sub 1dB/ of -11 dBm, and gain tuning range of 6.9 dB. The power consumption is 14.4 mW at V/sub DD/=1.8 V.