In situ diagnostics of Victorian brown coal combustion in O2/N2 and O2/CO2 mixtures in drop-tube furnace

Experimental investigation of the combustion of an air-dried Victorian brown coal in O₂/N₂ and O₂/CO₂ mixtures was conducted in a lab-scale drop-tube furnace (DTF). In situ diagnostics of coal burning transient phenomena were carried out with the use of high-speed camera and two-colour pyrometer for photographic observation and particle temperature measurement, respectively. The results indicate that the use of CO₂ in place of N₂ affected brown coal combustion behaviour through both its physical influence and chemical interaction with char. Distinct changes in coal pyrolysis behaviour, ignition extent, and the temperatures of volatile flame and burning char particles were observed. The large specific heat capacity of CO₂ relative to N₂ is the principal factor affecting brown coal combustion, which greatly quenched the ignition of individual coal particles. As a result, a high O₂ fraction of at least 30% in CO₂ is required to match air. Moreover, due to the accumulation of unburnt volatiles in the coal particle vicinity, coal ignition in O₂/CO₂ occurred as a form of volatile cloud rather than individual particles that occurred in air. The temperatures of volatile flame and char particles were reduced by CO₂ quenching throughout coal oxidation. Nevertheless, this negative factor was greatly offset by char-CO₂ gasification reaction which even occurred rapidly during coal pyrolysis. Up to 25% of the nascent char may undergo gasification to yield extra CO to improve the reactivity of local fuel/O₂ mixture. The subsequent homogeneous oxidation of CO released extra heat for the oxidation of both volatiles and char. As a result, the optical intensity of volatile flame in ∼27% O₂ in CO₂ was raised to a level twice that in air at the furnace temperature of 1273 K. Similar temperatures were achieved for burning char particles in 27% O₂/73% CO₂ and air. As this O₂/CO₂ ratio is lower than that for bituminous coal, 30-35%, a low consumption of O₂ is desirable for the oxy-firing of Victorian brown coal. Nevertheless, the distinct emission of volatile cloud and formation of strong reducing gas environment on char surface may affect radiative heat transfer and ash formation, which should be cautioned during the oxy-fuel combustion of Victorian brown coal.     

Experimental study of ash formation during pulverized coal combustion in O2/CO2 mixtures

The present paper was addressed to mineral transformations and ash formation during O₂/CO₂ combustion of pulverized coal. Four Chinese thermal coals were burned in a drop tube furnace to generate ashes under various combustion conditions. The ash samples were characterized with XRD analysis and ⁵⁷Fe Mössbauer spectroscopy. The impacts of O₂/CO₂ combustion on mineral transformation and ash formation were explored through comparisons between O₂/CO₂ combustion and O₂/N₂ combustion. It was found that, O₂/CO₂ combustion did not significantly change the mineral phases formed in the residue ashes, but did affect the relative amounts of the mineral phases. The differences observed in the ashes formed in two atmospheres were attributed to the impact of the gas atmosphere on the combustion temperatures of coal char particles, which consequently influenced the ash formation behaviors of included minerals.     

Modeling char conversion under suspension fired conditions in O2/N2 and O2/CO2 atmospheres

The aim of this investigation has been to model combustion under suspension fired conditions in O₂/N₂ and O₂/CO₂ mixtures. Experiments used for model validation have been carried out in an electrically heated Entrained Flow Reactor (EFR) at temperatures between 1173 K and 1673 K with inlet O₂ concentrations between 5 and 28 vol.%. The COal COmbustion MOdel, COCOMO, includes the three char morphologies: cenospheric char, network char and dense char each divided between six discrete particle sizes. Both combustion and gasification with CO₂ are accounted for and reaction rates include thermal char deactivation, which was found to be important for combustion at high reactor temperatures and high O₂ concentrations. COCOMO show in general good agreement with experimental char conversion profiles at conditions covering zone I-III. From the experimental profiles no effect of CO₂ gasification on char conversion has been found. COCOMO does however suggest that CO₂ gasification in oxy-fuel combustion at low O₂ concentrations can account for as much as 70% of the overall char consumption rate during combustion in zone III.     

Differences in reactivity of pulverised coal in air (O2/N2) and oxy-fuel (O2/CO2) conditions

The reactivity of four pulverised Australian coals were measured under simulated air (O₂/N₂) and oxy-fuel (O₂/CO₂) environments using a drop tube furnace (DTF) maintained at 1673 K and a thermogravimetric analyser (TGA) run under non-isothermal (heating) conditions at temperatures up to 1473 K. The oxygen concentration, covering a wide and practical range, was varied in mixtures of O₂/N₂ and O₂/CO₂ in the range of 3 to 21 vol.% and 5 to 30 vol.%, respectively. The apparent volatile yield measured in CO₂ in the DTF was greater than in N₂ for all the coals studied. Pyrolysis experiments in the TGA also revealed an additional mass loss in a CO₂ atmosphere, not observed in a N₂ atmosphere, at relatively high temperatures. The coal burnout measured in the DTF at several O₂ concentrations revealed significantly higher burnouts for two coals and similar burnouts for the other two coals in oxy-fuel conditions. TGA experiments with char also revealed higher reactivity at high temperatures and low O₂ concentration. The results are consistent with a char–CO₂ reaction during the volatile yield experiments, but additional experiments are necessary to resolve the mechanisms determining the differences in coal burnout.     

Coal devolatilization and char conversion under suspension fired conditions in O2/N2 and O2/CO2 atmospheres

The aim of the present investigation is to examine differences between O₂/N₂ and O₂/CO₂ atmospheres during devolatilization and char conversion of a bituminous coal at conditions covering temperatures between 1173 K and 1673 K and inlet oxygen concentrations between 5 and 28 vol.%. The experiments have been carried out in an electrically heated entrained flow reactor that is designed to simulate the conditions in a suspension fired boiler. Coal devolatilized in N₂ and CO₂ atmospheres provided similar results regarding char morphology, char N₂-BET surface area and volatile yield. This strongly indicates that a shift from air to oxy-fuel combustion does not influence the devolatilization process significantly. Char combustion experiments yielded similar char conversion profiles when N₂ was replaced with CO₂ under conditions where combustion was primarily controlled by chemical kinetics. When char was burned at 1573 K and 1673 K a faster conversion was found in N₂ suggesting that the lower molecular diffusion coefficient of O₂ in CO₂ lowers the char conversion rate when external mass transfer influences combustion. The reaction of char with CO₂ was not observed to have an influence on char conversion rates at the applied experimental conditions.     

An investigation of the causes of the difference in coal particle ignition temperature between combustion in air and in O2/CO2

The ignition temperatures of a Loy Yang brown coal and a Datong bituminous coal were investigated in a wire-mesh reactor where the secondary reactions of the evolved volatiles were minimised. An increase in the average particle ignition temperature of 21 °C was observed for the brown coal when air (21% O₂ + 79% N₂) was replaced with a mixture of 21% O₂ + 79% CO₂. Combustion was also carried out in the mixtures of 21% O₂ + 79% argon and 21%O₂ + 79% helium in order to determine the effects of heat transfer on the observed particle ignition temperature. It is concluded that the thermal conductivity of gas atmosphere surrounding the particles greatly influences the observed particle ignition temperature while the effects of the heat capacity of the gas atmosphere was very minor under our experimental conditions. The structure of char and the reactions involving the char (char-O₂ and char-CO₂) can greatly affect the observed particle ignition temperature. In particular, the char-CO₂ reactions were largely responsible for the observed difference in particle ignition temperature in air and in 21% O₂ + 79% CO₂. Alkali and alkaline earth metallic (AAEM) species in the brown coal also significantly affect the observed particle ignition temperature.     

Properties of char particles obtained under O2/N2 and O2/CO2 combustion environments

Pulverized coal combustion in O₂/N₂ and O₂/CO₂ environments was investigated with a drop tube furnace. Results present that the reaction rate and burn-out degree of O₂/CO₂ chars (obtained in O₂/CO₂ environments) are lower than that of O₂/N₂ chars (obtained in O₂/N₂ environments) under the same experimental condition. It indicates that a higher O₂ concentration in O₂/CO₂ environment is needed to achieve the similar combustion characteristic to that in O₂/N₂ environment. The main differences between O₂/N₂ and O₂/CO₂ chars rely on the pore structure determined by N₂ adsorption and chemical structure measured by FT-IR. For O₂/CO₂ char, the surface is thick and the pores are compact which contribute to the fragmentation reduction of particles burning in O₂/CO₂ environment. The organic functional group elimination rate from the surface of O₂/CO₂ chars is slower or delayed. The present research results might have important implications for further understanding the intrinsic kinetics of pulverized coal combustion in O₂/CO₂ environment.     

Preparation of ceramic nanospheres by CO2 laser vaporization (LAVA)

In order to prepare ceramic nanoparticles by CO₂ laser vaporization (LAVA) coarse ceramic powders (e.g. ZrO₂, Al₂O₃, and TiO₂) were used as raw materials. The raw powder was vaporized into a flowing process gas under normal pressure. Expanding into the gas, the vapor instantly cools down. Gas-phase condensation leads to the formation of nanoscale particles with a composition that corresponds to that of the raw powder. LAVA nanoparticles are chemically pure, spherical, crystalline, exhibit a narrow size distribution, and form merely soft agglomerates. The co-laser vaporization of mixtures of ceramic raw powders allows for the preparation of nanoparticles of multi-phase (e.g. Fe₂O₃-SiO₂) or single-phase (e.g. CaTiO₃) mixed-oxides and dispersion ceramics (e.g. ZrO₂-Al₂O₃). In order to modify the surface of the nanoparticles they can be coated in-process with an organic additive. Thus, the LAVA method allows for the targeted development of a wide range of ceramic nanopowders with tailored properties.     

Comparisons of pulverized coal combustion in air and in mixtures of O2/CO2

Pulverized coal combustion in air and the mixtures of O₂/CO₂ has been experimentally investigated in a 20 kW down-fired combustor (190 mm id×3 m). Detailed comparisons of gas temperature profiles, gas composition profiles, char burnouts, conversions of coal–N to NO_x and coal–S to SO₂ and CO emissions have been made between coal combustion in air and coal combustion in various O₂/CO₂ mixtures. The effectiveness of air/oxidant staging on reducing NO_x emissions has also been investigated for coal combustion in air and O₂/CO₂ mixtures. The results show that simply replacing the N₂ in the combustion air with CO₂ will result in a significant decrease of combustion gas temperatures. However, coal combustion in 30% O₂/70% CO₂ can produce matching gas temperature profiles to those of coal combustion in air while having a lower coal–N to NO_x conversion, a better char burnout and a lower CO emission. The results also confirm that air/oxidant staging is very effective in reducing NO_x emissions for coal combustion in both air and a 30% O₂/70% CO₂ mixture. SO₂ emissions are proved to be almost independent of the combustion media investigated.     

Pulverized coal combustion in air and in O2/CO2 mixtures with NOx recycle

This paper presents experimental results of a 20 kW vertical combustor equipped with a single pf-burner on pulverised coal combustion in air and O₂/CO₂ mixtures with NO_x recycle. Experimental results on combustion performance and NO_x emissions of seven international bituminous coals in air and in O₂/CO₂ mixtures confirm the previous findings of the authors that the O₂ concentration in the O₂/CO₂ mixture has to be 30% or higher to produce matching temperature profiles to those of coal-air combustion while coal combustion in 30% O₂/70% CO₂ leads to better coal burnout and less NO_x emissions than coal combustion in air. Experimental results with NO_x recycle reveal that the reduction of the recycled NO depends on the combustion media, combustion mode (staging or non-staging) and recycling location. Generally, more NO is reduced with coal combustion in 30% O₂/70% CO₂ than with coal combustion in air. Up to 88 and 92% reductions of the recycled NO can be achieved with coal combustion in air and in 30% O₂/70% CO₂ respectively. More NO is reduced with oxidant staging than without oxidant staging when NO is recycled through the burner. Much more NO is reduced when NO recycled through the burner (from 65 to 92%) than when NO is recycled through the staging tertiary oxidant ports (from 33 to 54%). The concentration of the recycled NO has little influence on the reduction efficiency of the recycled NO with both combustion media—air and 30% O₂/70% CO₂.     

Modelling of CO2, CO, SO2, O2 and NOx emissions from the oxy-fuel combustion in a circulating fluidized bed

The paper presents a model of coal combustion in air and oxygen-enriched CFB environment. A computer program to calculate the CO₂, CO, SO₂, NO_x and O₂ emissions from the combustion of solid fuels in a circulating fluidized bed boiler was created. The validity of this program was verified by measurements on a 0.1MW_th OxyFuel-CFB Test Rig.The calculations have been carried out for air and so-called oxy-fuel conditions, i.e. when combustion runs in a gas mixture based on O₂ and N₂, with various fractions of oxygen.The comparison between measured and predicted by model CO, SO₂, NO_x and O₂ emissions is shown in this paper. The results of the calculation showed, that the kinetic equations of some reaction have to be modified. Authors propose to use the reaction surface area instead of the specific internal surface area of char in rate constant formulas as the combustion nature changes from internal-kinetic to external-diffusion controlling regime.     

Iron transformations during combustion of Pittsburgh no. 8 coal

The chemical speciation of iron in combustion-derived ash is an important factor in determining the likelihood of ash deposit formation and buildup. In this study, the transformation of iron were examined in ash produced by the combustion of a beneficiated Pittsburgh no. 8 bituminous coal under a range of oxygen concentration ranging from 0% to 100% O₂ in a drop tube furnace. The speciation of iron was found to be strongly dependent upon ash particle size, with the lowest fraction of glassy state iron found in the largest ash particles. Both the fraction of iron in a glassy state and the ratio of Fe⁺⁺⁺(glass)/Fe⁺⁺(glass) increased with increasing O₂ concentration in the furnace. For the submicron ash particles, about 10% of the iron is formed by direct disintegration of pyrite and pyrrhotite during combustion. Most of the iron is however, present as Fe⁺⁺⁺(glass), which results from the vaporization, recondensation, and coagulation of iron and silicates. For ash particles with size between 1 and 9 microns, most of the ash derives from mineral coalescence within the reacting char, with additional contribution from extraneous minerals. The fraction of glassy iron in those particles is high because of the high contact probability between iron melt and silicates. For the coarsest ash particles with size greater than 9 microns, extraneous pyrite is changed into hematite, and iron in the core of the char is changed into a glassy state.     

New acrylic monolithic carbon molecular sieves for O2/N2 and CO2/CH4 separations

The modification of activated carbon fibres prepared from a commercial textile acrylic fibre into materials with monolithic shape using phenolic resin as binder was studied. The molecular sieving properties for the gas separations CO₂/CH₄ and O₂/N₂ were evaluated from the gas uptake volume and selectivity at 100 s contact time taken from the kinetic adsorption curves of the individual gases. The pseudo-first order rate constant was also determined by the application of the LDF model. The samples produced show high CO₂ and O₂ rates of adsorption, in the range 3-35 × 10⁻³ s⁻¹, and in most cases null or very low adsorption of CH₄ and N₂ which make them very promising samples to use in PSA systems, or similar. Although the selectivity was very high, the adsorption capacity was low in certain cases. However, the gas uptake in two samples reached 23 cm³ g⁻¹ for CO₂ and 5 cm³ g⁻¹ for O₂, which can be considered very good. The materials were heat-treated using a microwave furnace, which is a novel and more economic method, when compared with conventional furnaces, to improve the molecular sieves properties.     

Ash partitioning during the oxy-fuel combustion of lignite and its dependence on the recirculation of flue gas impurities (H2O, HCl and SO2)

Oxy-fuel combustion of a brown coal (i.e. lignite) has been carried out at 1000 °C to experimentally examine the vaporisation of organically bound metals and the agglomeration of ash particles as a function of the concentration of gaseous impurities including H₂O, HCl and SO₂ in ∼27% O₂ balanced with CO₂. The properties of bulk ash and individual metals were investigated intensively. Particularly, attention was paid to Na which is notorious for fouling and to organically bound Al which has been less studied. The results indicate that, the organically bound metals, although possessing a very low content in the raw coal, are vital for the agglomeration of ash particles, which are also highly sensitive to the loading of gas impurities in flue gas. HCl recirculation is the most crucial factor promoting the vaporisation of metals via chlorination. Apart from alkali metals, the organically bound Al and Ti were also vaporised noticeably. Recirculation of SO₂ promoted the sulfation of Na to condense into liquid droplet which increased fine ash yield. Co-existence of bulk HCl and SO₂ played a synergetic role in the sufation of Na via an initial chlorination of the char-bound Na. In contrast, co-existence of steam with HCl and SO₂ favored the formation of Na alumino-silicates, which are favorable for ash agglomeration.     

Coal char combustion under a CO2-rich atmosphere: Implications for pulverized coal injection in a blast furnace

Pulverized coal injection (PCI) is employed in blast furnace tuyeres attempting to maximize the injection rate without increasing the amount of unburned char inside the stack of the blast furnace. When coal is injected with air through the injection lance, the resolidified char will burn in an atmosphere with a progressively lower oxygen content and higher CO₂ concentration. In this study an experimental approach was followed to separate the combustion process into two distinct devolatilization and combustion steps. Initially coal was injected into a drop tube furnace (DTF) operating at 1300 °C in an atmosphere with a low oxygen concentration to ensure the combustion of volatiles and prevent the formation of soot. Then the char was refired into the DTF at the same temperature under two different atmospheres O₂/N₂ (typical combustion) and O₂/CO₂ (oxy-combustion) with the same oxygen concentration. Coal injection was also performed under a higher oxygen concentration in atmospheres typical for both combustion and oxy-combustion. The fuels tested comprised a petroleum coke and coals currently used for PCI injection ranging from high volatile to low volatile bituminous rank. Thermogravimetric analyses and microscopy techniques were used to establish the reactivity and appearance of the chars.     

CO2 capture using oxygen enhanced combustion strategies for natural gas power plants

This paper describes a series of experiments conducted with natural gas in air and in mixtures of oxygen and recycled flue gas, termed O₂/CO₂ recycle combustion. The objective is to enrich the flue gas with CO₂ to facilitate its capture and sequestration. Detailed measurements of gas composition, flame temperature and heat flux profiles were taken inside CANMET's 0.3 MWth down-fired vertical combustor fitted with a proprietary pilot scale burner. Flue gas composition was continuously monitored. The effects of burner operation, including swirling of secondary stream and air staging, on flame characteristics and NO_x emissions were also studied. The results of this work indicate that oxy-gas combustion techniques based on O₂/CO₂ combustion with flue gas recycle offer excellent potential for retrofit to conventional boilers for CO₂ emission abatement. Other benefits of the technology include considerable reduction and even elimination of NO_x emissions, improved plant efficiency due to lower gas volume and better operational flexibility.     

CO2 sequestration from coal fired power plants

The paper takes into consideration a new approach for CO₂ capture and transport, based on the formation of solid CO₂ hydrates.Carbon dioxide sequestration from power plants can take advantage of the properties of gas hydrates. The formation and decomposition of hydrates from various N₂-CO₂ mixtures has been studied experimentally in a 2 l reactor, to determine the CO₂ separation in terms of hydrate composition and residual CO₂ content in the reacted gas.Carbon dioxide acts as a co-former for the production of hydrates containing nitrogen, besides CO₂. The mixed hydrates that are obtained are less stable than simple CO₂ hydrates. When CO₂ content in the flue gas is higher than 30% by volume, the hydrates formed at 5 MPa are sufficiently concentrated (about 70% CO₂) and carbon dioxide reduction in the reacted gas is acceptable.The application of a process based on hydrate formation could be especially interesting (for CO₂ capture and transport) when connected to an oxy-coal combustion process; in this case the CO₂ content in the flue gas is very high and the hydrate formation is greatly facilitated.     

O2/CO2气氛下煤燃烧SO2/NO析出特性

在水平管式炉上研究了O₂浓度、CO₂浓度、温度及石灰石添加等各参数对O₂/CO₂气氛下徐州烟煤和龙岩无烟煤燃烧过程中SO₂/NO排放特性的影响。结果发现,O₂/CO₂气氛下,烟煤和无烟煤燃烧SO₂/NO的析出规律与空气气氛下不同,同等O₂浓度下析出量比空气气氛下小。O₂/CO₂气氛下,随着O₂浓度的提高,烟煤和无烟煤SO₂/NO排放量均增大;随着CO₂浓度的升高, SO₂/NO排放量均减小。O₂/CO₂气氛下,石灰石添加对SO₂排放的抑制作用低于空气气氛下;石灰石添加对NO的排放有一定减排作用。对煤灰的元素分析显示O₂/CO₂燃烧对SO₂的抑制主要是由于煤灰的自固硫能力增强,而对NO的减排作用则是促进燃料N向其他含N气体的转换。     

Theoretical and experimental study on the emission characteristics of waste plastics incineration by modified O2/RFG combustion technology

For mitigating the emission of greenhouse gas CO₂ from general air combustion systems, a clean combustion technology O₂/RFG is in development. The O₂/RFG combustion technology can significantly enhance the CO₂ concentration in the flue gas; however, using almost pure oxygen or pure CO₂ as feed gas is uneconomic and impractical. As a result, this study proposes a modified O₂/RFG combustion technology in which the minimum pure oxygen is mixed with the recycled flue gas and air to serve as the feed gas. The effects of different feed gas compositions and ratios of recycled flue gas on the emission characteristics of CO₂, CO and NO_x during the plastics incineration are investigated by theoretical and experimental approaches.Theoretical calculations were carried out by a thermodynamic equilibrium program and the results indicated that the emissions of CO₂ were increased with the O₂ concentrations in the feed gas and the ratios of recycled flue gas increased. Experimental results did not have the same trends with theoretical calculations. The best feed gas composition of the modified O₂/RFG combustion was 40% O₂ + 60% N₂ and the best ratio of recycled flue gas was 15%. As the O₂ concentration in feed gas and the ratio of recycled flue gas increased, the total flow rates and pressures of feed gas reduced. The mixing of solid waste and feed gas was incomplete and the formation of CO₂ decreased. Moreover, the emission of CO was decreased as the O₂ concentration in feed gas and the ratio of recycled flue gas increased. The emission of NO_x gradually increased with rising the ratio of recycled flue gas at lower O₂ concentration (<40%) but decreased at higher O₂ concentration (>60%).     

Formation of NOx precursors during the pyrolysis of coal and biomass. Part VI. Effects of gas atmosphere on the formation of NH3 and HCN

Our results indicate that the gas atmosphere surrounding coal/char particles can greatly affect the formation of NH₃ and HCN through its influence on the availability of H radicals. Based on our results, it is believed that the chemisorption of CO₂ on the nascent char surface can consume H radicals or block the access of N-sites by H radicals for the formation of NH₃ and HCN. For the chars whose thermal cracking generates little H radicals, the gasification of char by CO₂ can also generate additional H radicals, enhancing the formation of NH₃. However, even gasification of char in CO₂ at 950 °C does not lead to the formation of HCN. The oxidation of coal with 4% O₂ at low temperatures (400-600 °C) leads to the formation of HCN as well as NH₃ due to the enhanced formation of (H) radicals. The gasification of coal with 15% H₂O drastically enhances the formation of NH₃ due to the greatly enhanced availability of H as an intermediate between the reactions of H₂O and char. These results support our reaction mechanisms proposed previously, emphasising the importance of H on the formation of NH₃ and HCN during pyrolysis, which can also be extended to the conversion of coal-N during gasification.