Filling behavior of UV nanoimprint resin observed by using a midair structure mold

The filling behavior of resin during UV nanoimprint lithography (UV-NIL) was observed by using a “midair structure mold” and by changing the imprint pressure. The midair structure molds were fabricated by electron beam lithography (EBL) using hydrogen silsesquioxane (HSQ) as a negative tone resist. After the fabrication of midair structure mold, two types of surface treatment molds, which were with or without release coating, were prepared. Using these molds, the filling behavior of a UV curable resin was investigated at various pressures. The results indicate that a pressure of approximately 1.2 MPa is necessary for complete filling in the case of molds treated with a release agent. This method demonstrates effect of a release coating for UV-NIL.     

Large area nanosize array stamp for UV-based nanoimprint lithography fabricated by size reduction process

A novel size reduction process using electron beam lithography (EBL) combining with wet etching technique is developed as a possible solution for producing large area and low cost nanopattern stamp for UV-based nanoimprint lithography (UV-NIL). In the first step, a microstructure stamp with 1.4 μm periodical pore array and aspect ratio of 1:1 was formed over a 1 inch² area on a quartz substrate. This process was carried out using common electron beam lithography (EBL) equipment, which was easily available in the modern integrated circuits (IC) semiconductor factory. Afterwards, with a controlled wet etching technique, the pore array was changed into tip patterns with the line width below 100 nm and the period keeping as before. The uniformities and nanopattern accuracies were investigated to identify its possibility as a UV-NIL stamp by AFM and SEM. Finally, as a demonstration, the as obtained stamp was used as a positive stamp to replicate the nanotips into UV-curable resist successfully by a UV-NIL process. The method developed for the mold of nanoimprint lithography would be a simple and low price approach to fabricate large area UV-NIL stamp and the nanotip array structures would be widely used in two dimensional (2D) photonic crystal application.     

Technique for transfer of high-density,high-aspect-ratio nanoscale patterns in UV nanoimprint lithography and measurement of the release force

Ultraviolet nanoimprint lithography (UV-NIL) is a powerful tool for nanoscale fabrication. However, the replication of high-density, high-aspect-ratio mold patterns by UV-NIL is very difficult because of the strong forces required to release the replicate from the mold. We used a glassy carbon (GC) mold with an antireflective structure, fabricated by irradiation with an oxygen-ion beam, to produce a high-density, high-aspect-ratio pattern, and we evaluated its release properties. The fabricated GC surface contained high-aspect-ratio conical structures with pitch of less than 100 nm. After fabrication of the antireflective structure, the mold surface was coated with chromium and a fluorinated silane coupling agent. By using this treatment and a peel motion during mold release, faithful replication of the mold structure in photocurable resin was possible. The release force increased with increasing mold surface area; the surface area effect is therefore the main factor in the mold-release step.     

Direct soft UV-NIL with resist incorporating carbon nanotubes

As a potential candidate for the next generation of nanolithography, nanoimprint lithography (NIL) has drawn ever-increasing worldwide attention. It involves physical contact to overcome the optical limits occurring in sub-100 nm photolithography. Affordable tool cost is one of major attractive points of NIL. This work proposes the idea of incorporating carbon nanotubes (CNTs) in the resin used for ultraviolet nanoimprinting (UV-NIL). CNTs can make the resin electrically conductive when mixed with it. Patterns imprinted in the CNT-mixed resist can then be used to replace conductive metal structures directly. This enhances the productivity of basic UV-NIL where the imprinted patterns are used as sacrificial etch masks. In this work, several types of CNTs were purified chemically and dispersed before being mixed with UV-NIL resin using ultrasonic vibration. On drops of CNT-mixed resin, soft UV-NIL was performed using a polydimethylsiloxane (PDMS) stamp with a minimum feature size in the range of 200 nm. Even with increased resin viscosity due to the addition of CNTs, UV imprinting down to 200 nm was successfully done with moderate pattern fidelity. The loading rate of nanotubes should be minimized to prevent the increased viscosity from degrading the pattern transfer resolution. The electrical conductivity of CNT-mixed resist increases with the loading of CNTs. Therefore, the trade-off between the electrical properties and pattern transfer resolution needs to be optimized carefully.     

Development of a novel,low-viscosity UV-curable polymer system for UV-nanoimprint lithography

There are two basic types of nanoimprint lithography: hot embossing using thermoplastic or thermosetting polymers and UV-based nanoimprint lithography (UV-NIL) using UV-curable polymer systems. Since the interest in UV-NIL has been constantly increasing within the last years, the need of suitable low-viscosity resists has increased, too. The availability of such materials is one key element of the UV-NIL technology. In this contribution a novel, spin-coatable polymer system for UV-NIL is presented. Suitable polymer components were evaluated using photoDSC analysis. Their ratio was adjusted in such a way that the overall dynamic viscosity of the mixture remained low which was beneficial for the flow behaviour. Film thicknesses in the range of 150–500 nm could be obtained by spin-coating. The new polymer system was characterised in UV-NIL processes and in plasma etching investigations. Imprinted micrometer as well as nanometer scale patterns with feature sizes in the range of 30 nm to several microns are shown.     

Fabrication of sub-micron 3-D structure using duo-mold UV-RIL process

3-D polymeric micro- and nano-structures were fabricated by the reversal imprint lithography technique using nano-patterned molds. A surface-treated quartz mold and a water-soluble poly vinyl alcohol (PVA) mold were used to make dual-side patterned, 2-D polymeric, micro- and nano-structures. First, UV-curable, polymeric resin was dropped onto the quartz mold, which was then covered with the PVA mold. The two stacked molds were pressed and exposed to UV-light to cure the resin. The cured polymeric resin (the reversal layer) was easily released from the quartz mold, because the surface of the latter was treated with an anti-stiction layer. The reversal layer, bound to the PVA mold, was transferred to a Si substrate by applying a thin layer of a UV-curable bonding agent. After bonding the reversal layer, the PVA mold was selectively removed by dipping in water. As a result, the dual-side patterned, thin polymeric 2-D structure was formed on the silicon substrate and, by repeating this process, 2-D nano-structures were stacked to form a 3-D nano-structure. By making use of the anti-stiction-treated, quartz mold and the water-soluble characteristic of the PVA material, the reliable release of the reversal layer was achieved.     

A versatile pattern inversion process based on thermal and soft UV nanoimprint lithography techniques

Si master molds are generally patterned by electron-beam lithography (EBL) that is known to be a time-consuming nanopatterning technique. Thus, developing mold duplication process based on high throughput technique such as nanoimprint lithography can be helpful in reducing its fabrication time and cost. Moreover, it could be of interest to get inverted patterns (holes instead of pillars) without changing the master EBL process. In this paper, we propose a two step process based on thermal nanoimprint lithography (T-NIL) (step 1) and soft UV assisted nanoimprint lithography (UV-NIL) (step 2) to invert a master EBL mold. After the two inversion steps, the grand-daughter Si mold exhibits the same pattern polarity as the EBL mold. For step 1, pattern transfer using ion beam etching (IBE) of a thin metallic underlayer is the critical step for dimension control due to the low NXR1020 resistance. For step 2, the optimized reactive ion etching (RIE) step allows transfer with good anisotropy even for nanostructures at the 50 nm-scale. For structures larger than 100 nm, this inversion process has been successfully applied to large field replication (up to 1.5 cm²) on whole wafer.     

Fabrication of low-cost mold and nanoimprint lithography using polystyrene nanosphere

The periodic arrays of nanostructure were successfully patterned on Si wafers by ultraviolet nanoimprint lithography (UV-NIL) using nanosphere lithography (NSL). Two-dimensional (2D) well ordered self-assembled arrays were obtained on Si wafer by using nanosphere and the tilted-drain method. We tried to combine two techniques and hard mold of Si mold for NIL and polymer mold of acrylate-based polymer were fabricated by NSL. The Si master mold and polymer mold were formed by Cr lift-off and ICP-RIE process. The surface has a low surface energy at the interface with 1H, 1H, 2H, 2H-perfluorooctyl-trichlorosilane (FOTS) vapor-coating, which can eliminate the problem of the adherence to the surface of the mold during demolding. Finally, nanopatterns were formed by UV-NIL, where the residual layer was not observed.     

Wafer deformation in ultraviolet-nanoimprint lithography using an element-wise patterned stamp

Nanoimprint lithography is a promising method for high-resolution, low-cost nanopatterning. In particular, ultraviolet-nanoimprint lithography (UV-NIL), which requires low imprint pressure, is effective for multi-layer processes. In this study, we investigated the non-uniformity of the residual layer thickness caused by wafer deformation in an experiment that examined different wafer thicknesses using UV-NIL with an element-wise patterned stamp (EPS). The EPS consisted of a number of elements, each separated by a channel. Experiments using the EPS were performed on an EVG620-NIL. Severe deformation of the wafer served as an obstacle to the spread of resin drops, which caused non-uniformity of the residual layer thickness. We also simulated the imprint process using a simplified model and finite element method to analyze the non-uniformity.     

Fabrication of three-dimensional nanoimprint mold using inorganic resist in low accelerating voltage electron beam lithography

Three-dimensional (3D) resolution of inorganic resist pattern, which was exposed with control of acceleration voltage electron beam lithography (CAV-EBL) in low accelerating voltage was examined. The system can make features with varying developed-depths. Three-dimensional pattern with a few hundred nanometer linewidth was fabricated with a CAV-EBL. The pattern depths on inorganic resist were gradated with 5 nm depth-resolution per 30 V. By controlling the pattern depth, a seven stairs blade-shaped binary optics mold was fabricated, and then a replica pattern of the mold was made by using UV-NIL.     

Fluorinated materials for UV nanoimprint lithography

The “demolding” is the important key for UV nanoimprint lithography (UV-NIL) which attracts a lot of attention recently as microfabrication technique. Then, we present in this paper, new fluorinated mold material and new fluorinated photosensitive polymer which are suitable for the UV-NIL because of their high transparency and excellent mold-release characteristics. By using our mold material “F-template”, the process cost can be drastically reduced because it can be used as replicated mold instead of using expensive quartz master mold. F-template requires no releasing agent is another advantage. We also developed photosensitive polymer “NIF-A-1” which has high transparency, good mold-releasing ability and good dry etching resistance. Unlike the common photosensitive polymer, NIF-A-1 did not need a releasing agent on the mold.     

硅油稀释PDMS法制备紫外纳米压印软模板

软模板的制作是紫外纳米压印中关键的技术,模版的分辨率直接决定了压印图形的最小分辨率。使用具有高度均匀、100nm级孔洞阵列结构的多孔氧化铝作为母版,使用基于液态浇铸的硅油稀释聚二甲基硅氧烷(硅油和聚二甲基硅氧烷的质量比为1:2)法制备出具有规则点阵结构的软模板。通过SEM和AFM表征发现,特征图形得到了有效转移,特征尺度保持在100nm左右。相对于传统的模板制备方法,此方法成本低、流程简单、适合大规模生产,是一种非常有前途的软模板制备方法。     

Gold nanoparticles by soft UV nanoimprint lithography coupled to a lift-off process for plasmonic sensing of antibodies

In this paper, we present the results of gold nanoparticles fabrication on large area by soft UV nanoimprint lithography (UV-NIL) and lift-off process for antibodies sensing. For this fabrication, the hard polydimethylsiloxane (H-PDMS) is used as flexible mold material. A simple AMONIL/PMMA bilayer is used to transfer patterns by etching the substrate with a suitable RIE process. The UV-NIL process has enabled to obtain gold nanoparticles with a diameter about 160 nm on a zone of 1 mm². For bioplasmonic applications, the sensing of Anti-Biotin was studied.     

A 4-in.-based single-step UV-NIL tool using a low vacuum environment and additive air pressure

Ultraviolet nanoimprint lithography (UV-NIL) is a promising technology for the fabrication of sub-10-nm features. Research has focused on employing a large-area stamp to improve UV-NIL throughput, but a large-area stamp makes it difficult to obtain an acceptable uniform residual layer thickness and/or avoid defects such as air entrapment. This paper presents the development of a single-step UV-NIL tool in which a 4-in. Pyrex stamp is first used to imprint coated resin against a 4-in. Si wafer in a low vacuum environment. Pressurized N₂ is subsequently applied to the wafer bottom to improve the quality of imprint results. This UV-NIL tool was used to successfully imprint a 4-in. stamp with recessed patterns engraved over the entire stamp areas onto a 4-in. Si wafer.     

Nanoholes by soft UV nanoimprint lithography applied to study of membrane proteins

In this paper, we present an alternative technique to the well-known electron beam lithography in order to realize nanoholes in the silicon substrates for biological applications. The used technique is soft UV nanoimprint lithography (UV-NIL). We optimized the fabrication of silicon based supports obtained by soft UV-NIL and reactive ion etching to carry out very large arrays of nanoholes. The resolution limits are investigated when using poly(dimethylsiloxane) as flexible mold material. RIE conditions are initiated to limit the lateral mask resist etch.     

Nanoelectrode lithography using a flat mold with a pattern defined by different conductivities

Nanoelectrode lithography is a pattern duplication method that combines nanoimprint with an electrochemical reaction. The method can form an oxide pattern directly on a semiconductor or metal. This method can use flat molds with patterns defined by substances with different conductivities, while the conventional nanoimprint technique must use a mold with a relief pattern. In this paper, the mold pattern for the technique is defined with an oxide material on the surface of a conductive substrate. Nanoelectrode lithography itself can be used to form a flat mold by using a conductive mold with a relief pattern, which leaves an oxide pattern via the anodic oxidation of Si. AFM lithography also can utilize an electrochemical reaction in the air to generate an oxide pattern on a conductive substrate, which gives us a flat mold. This paper shows that both types of flat mold can transfer a pattern to a target substrate. These strategies will allow us to realize on-demand mold fabrication, mold modification, and an easy way of obtaining a mold with a finer pattern.     

新型高抗粘紫外纳米压印光刻胶的工艺研究

为了减少紫外纳米压印技术脱模过程中的接触粘附力,开发了一种新型高流动、抗粘的紫外纳米压印光刻胶。光刻胶以BMA为聚合单体,添加特定配比的交联剂和光引发剂配置而成。紫外纳米压印实验在本课题组自主研发的IL-NP04型纳米压印机上完成。实验得到光刻胶掩膜膜厚为1.21μm,结构尺寸深246nm,周期937.5nm。实验结果表明,在没有对石英模板表面进行修饰的情况下,该光刻胶依然表现出高可靠性和高图形转移分辨率,有效减少了紫外纳米压印工艺中的模板抗粘修饰的工艺步骤。     

UV nanoimprint lithography with rigid polymer molds

Transparent polymers are considered as alternative low-cost mold materials in UV nanoimprint lithography (UV-NIL). Here, we demonstrate a nanoimprint process with molds made of rigid polymers novel for this application. These polymer molds are found to show high performance in the patterning with UV-NIL. Sub-50 nm structures were fabricated with this process.     

Characterisation of ultraviolet nanoimprint dedicated resists

We have developed a new resist material, named NILTM105, for the purpose of ultraviolet curing nanoimprint lithography. Its capability for micro- and nano-scale features patterning has been experimentally analyzed and compared to two other commercially available UV-NIL resists (AMONIL-MMS4 proposed by AMO GmbH, Germany and PAK-01 from Toyo Gosei, Japan). Using 3D-atomic force microscopy, cross section scanning electron microscopy, CD-SEM and ellipsometric measurements, the suitability of this resist for a reliable replication of the mold features was confirmed. Besides, detailed study of the residual thickness and features height variation as a function of pattern size and density has proven that the three investigated resists can flow over distances on the millimeter range. Finally, the etch resistance of the home-developed material was characterized under several plasmas conditions. It was found out that the etch rates values are compatible with the use of this resist as a masking layer during transfer steps.     

A step-and-repeat UV-nanoimprint lithography process using an elementwise patterned stamp

Ultraviolet-nanoimprint lithography (UV-NIL) is a promising cost-effective method for defining nanoscale structures at room temperature and low pressure. To apply a large-area stamp to a high throughput step-and-repeat process at atmospheric conditions, we proposed a new UV-NIL process that uses an elementwise patterned stamp (EPS), which consists of elements separated by channels, and additive gas pressurization. The proposed UV-NIL process required just four imprints to press an 8-in. wafer. EPS features measuring 50-80 nm were successfully transferred onto the wafers. The experiments demonstrated that a 5 × 5-in.² EPS could be used with a step-and-repeat UV-NIL process to imprint 8-in. wafers under atmospheric conditions.