Magnetron-sputtered high performance Y-doped ZnO thin film transistors fabricated at room temperature

In this report, sputtered-grown undoped ZnO and Y-doped ZnO (ZnO:Y) thin film transistors (TFTs) are presented. Both undoped ZnO and ZnO:Y thin films exhibited highly preferred c-axis oriented (002) diffraction peaks. The ZnO:Y thin film crystallinity was improved with an increase of (002) peak intensity and grain size. The electrical properties of ZnO:Y TFTs were significantly enhanced relative to undoped ZnO TFTs. ZnO:Y TFTs exhibited excellent performance with high mobility of 38.79 cm² V⁻¹ s⁻¹, small subthreshold swing of 0.15 V/decade, and high I_on/I_off current ratio of the order of 8.17 × 10⁷. The O_1s X-ray photoelectron spectra (XPS) showed oxygen vacancy-related defects present in the ZnO:Y TFTs, which contributed to enhancing the mobility of the TFTs.     

Sputtered oxides used for passivation layers of amorphous InGaZnO thin film transistors

Four sputtered oxide films (SiO₂, Al₂O₃, Y₂O₃ and TiO₂) along with their passivating amorphous InGaZnO thin film transistors (a-IGZO TFTs) were comparatively studied in this paper. The device passivated by an Al₂O₃ thin film showed both satisfactory performance (μ_FE=5.3 cm²/V s, I_on/I_off>10⁷) and stability, as was probably related to smooth surface of Al₂O₃ thin films. Although the performance of the a-IGZO TFTs with a TiO₂ passivation layer was also good enough (μ_FE=3.5 cm²/V s, I_on/I_off>10⁷), apparent V_th shift occurred in positive bias-stress tests due to the abnormal interface state between IGZO and TiO₂ thin films. Sputtered Y₂O₃ was proved no potential for passivation layers of a-IGZO TFTs in this study. Despite unsatisfactory performance of the corresponding a-IGZO TFT devices, sputtered SiO₂ passivation layer might still be preferred for its high deposition rate and excellent transparency which benefit the mass production of flat panel displays, especially active-matrix liquid crystal displays.     

Effects of RTA temperatures on conductivity and micro-structures of boron-doped silicon nanocrystals in Si-rich oxide thin films

In this work, the B-doped Si rich oxide (SRO) thin films were deposited and then annealed using rapid thermal annealing (RTA) to form SiO₂-matrix silicon nanocrystals (Si NCs). The effects of the RTA temperatures on the structural properties, conduction mechanisms and electrical properties of B-doped SRO thin films (BSF) were investigated systematically using Hall measurements, Fourier transform infrared spectroscopy and Raman spectroscopy. Results showed that the crystalline fraction of annealed BSF increased from 41.3% to 62.8%, the conductivity was increased from 4.48×10⁻³ S/cm to 0.16 s/cm, the carrier concentration was increased from 8.74×10¹⁷ cm⁻³ to 4.9×10¹⁸ cm⁻³ and the carrier mobility was increased from 0.032 cm² V⁻¹ s⁻¹ to 0.2 cm² V⁻¹ s⁻¹ when the RTA temperatures increased from 1050 °C to 1150 °C. In addition, the fluctuation induced tunneling (FIT) theory was applicable to the conduction mechanisms of SiO₂-matrix boron-doped Si-NC thin films.     

Effect of gate insulator thickness on device performance of InGaZnO thin-film transistors

Top-contact thin-film transistors (TFTs) are fabricated in this work using atomic layer deposition (ALD) Al₂O₃ as the gate insulator and radio frequency sputtering InGaZnO (IGZO) as the channel layer so as to investigate the effect of Al₂O₃ thickness on the performance of IGZO-TFTs. The results show that TFT with 100-nm-thick Al₂O₃ (100 nm-Al₂O₃-TFT) exhibits the best electrical performance; specifically, field-effect mobility of 5 cm²/Vs, threshold voltage of 0.95 V, I_on/I_off ratio of 1.1×10⁷ and sub-threshold swing of 0.3 V/dec. The 100 nm-Al₂O₃-TFT also shows a substantially smaller threshold voltage shift of 1.1 V after a 10 V gate voltage is applied for 1 h, while the values for TFTs with an Al₂O₃ thickness of 220 and 280 nm are 1.84 and 2 V, respectively. The best performance of 100 nm-Al₂O₃-TFT can be attributed to the larger capacitance and the smaller amount of total trap centers possessed by a thinner insulator compared to the thicker ones.     

Annealing effects on physical properties of doped CdTe thin films for photovoltaic applications

Polycrystalline Cadmium Telluride (CdTe) thin films were prepared on glass substrates by thermal evaporation at the chamber ambient temperature and then annealed for an hour in vacuum ~1×10⁻⁵ mbar at 400 °C. These annealed thin films were doped with copper (Cu) via ion exchange by immersing these films in Cu (NO₃)₂ solution (1 g/1000 ml) for 20 min. Further these films were again annealed at different temperatures for better diffusion of dopant species. The physical properties of an as doped sample and samples annealed at different temperatures after doping were determined by using energy dispersive x-ray analysis (EDX), x-ray diffraction (XRD), Raman spectroscopy, transmission spectra analysis, photoconductivity response and hot probe for conductivity type. The optical band gap of these thermally evaporated Cu doped CdTe thin films was determined from the transmission spectra and was found to be in the range 1.42–1.75 eV. The direct energy band gap was found annealing temperatures dependent. The absorption coefficient was >10⁴ cm⁻¹ for incident photons having energy greater than the band gap energy. Optical density was observed also dependent on postdoping annealing temperature. All samples were found having p-type conductivity. These films are strong potential candidates for photovoltaic applications like solar cells.     

Effects of annealing on nanocrystalline Bi2S3 thin films prepared by chemical bath deposition

Nanocrystalline Bi₂S₃ thin films are deposited on tin chloride treated glass substrate from the solution containing bismuth nitrate, triethanolamine (TEA) and thioacetamide (TAM) at a bath temperature 318 K. The prepared films are subsequently annealed at different temperatures for studying the effect of thermal treatment on the structural, surface morphology, optical and electrical properties of the films. The X-ray diffraction studies affirmed that the deposited films are orthorhombic structures with average crystallites size of 14 nm to 28 nm. The scanning electron microscopy (SEM) images revealed that the films comprise of grains of spherical shape of unequal size. It is also observed that the small particles aggregate together to form a larger cluster. The average grain sizes determined from the TEM images are smaller than the crystallites size obtained from the XRD studies. The optical band gap of the films has been estimated to be 2.24–2.05 eV for the as-prepared and annealed films, respectively. The electrical conductivity of the as prepared Bi₂S₃ films at room temperature is found to be in the order of 10⁻³ Ω⁻¹ m⁻¹.     

High performance electric-double-layer amorphous IGZO thin-film transistors gated with hydrated bovine serum albumin protein

Device performance of amorphous indium gallium zinc oxide (a-IGZO) thin film transistors (TFTs) has been improved greatly by using bovine serum albumin (BSA) as the top gate dielectric. BSA is a natural protein with acidic and basic amino acid residues, which is easily hydrated in air ambient. A typical a-IGZO TFT with hydrated BSA as the top gate dielectric exhibits a field-effect mobility (μ_FE) value of 113.5 cm² V⁻¹ s⁻¹ in saturation regime and a threshold voltage (V_TH) value of 0.25 V in air ambient. The excellent device performance can be well explained by the formation of electric double layers (EDLs) near the interfaces of a-IGZO/hydrated BSA and hydrated BSA/gate electrode. The reliability issue of a-IGZO TFTs gated with hydrated BSA has been also investigated by using the life time test without encapsulation. The V_TH value increases and μ_FE,sat value reduces slightly for the a-IGZO TFT and remain stabilized over 60 days.     

Sol–gel derived nanocrystalline TiO2 thin films: A promising candidate for self-cleaning smart window applications

In the present work, anatase TiO₂ films are prepared by sol–gel spin coating method. The structural and optical properties of the films have been studied at different post-annealing temperatures. The photocatalytic activity and electrochromic performance of the films are investigated. The films annealed at 400 °C exhibit the highest photocatalytic activity with a rate constant of 4.56×10⁻³ min⁻¹. The electrochromic performance for the films annealed at 400 °C expressed in terms of difference in optical density (ΔOD) at 550 nm between coloured and bleached state is 0.5493. This combination of photocatalysis and electrochromism makes the sol–gel derived titania thin films as promising candidates for self-cleaning smart window applications.     

IGZO thin film transistors with Al2O3 gate insulators fabricated at different temperatures

Thin film transistors (TFTs) with bottom gate and staggered electrodes using atomic layer deposited Al₂O₃ as gate insulator and radio frequency sputtered In–Ga–Zn Oxide (IGZO) as channel layer are fabricated in this work. The performances of IGZO TFTs with different deposition temperature of Al₂O₃ are investigated and compared. The experiment results show that the Al₂O₃ deposition temperature play an important role in the field effect mobility, I_on/I_off ratio, sub-threshold swing and bias stability of the devices. The TFT with a 250 °C Al₂O₃ gate insulator shows the best performance; specifically, field effect mobility of 6.3 cm²/Vs, threshold voltage of 5.1 V, I_on/I_off ratio of 4×10⁷, and sub-threshold swing of 0.56 V/dec. The 250 °C Al₂O₃ insulator based device also shows a substantially smaller threshold voltage shift of 1.5 V after a 10 V gate voltage is stressed for 1 h, while the value for the 200, 300 and 350 °C Al₂O₃ insulator based devices are 2.3, 2.6, and 1.64 V, respectively.     

Dielectric surface-polarity tuning and enhanced operation stability of solution-processed organic field-effect transistors

The electrical performance of triethylsilylethynyl anthradithiophene (TES-ADT) organic field-effect transistors (OFETs) was significantly affected by dielectric surface polarity controlled by grafting hexamethyldisilazane and dimethyl chlorosilane-terminated polystyrene (PS-Si(CH₃)₂Cl) to 300-nm-thick SiO₂ dielectrics. On the untreated and treated SiO₂ dielectrics, solvent–vapor annealed TES-ADT films contained millimeter-sized crystals with low grain boundaries (GBs). The operation and bias stability of OFETs containing similar crystalline structures of TES-ADT could be significantly increased with a decrease in dielectric surface polarity. Among dielectrics with similar capacitances (10.5–11 nF cm⁻²) and surface roughnesses (0.40–0.44 nm), the TES-ADT/PS-grafted dielectric interface contained the fewest trap sites and therefore the OFET produced using it had low-voltage operation and a charge-carrier mobility ∼1.32 cm² V⁻¹ s⁻¹, on–off current ratio >10⁶, threshold voltage ∼0 V, and long-term operation stability under negative bias stress.     

High-performance pentacene field-effect transistors using Al2O3 gate dielectrics prepared by atomic layer deposition (ALD)

High-performance pentacene field-effect transistors have been fabricated using Al₂O₃ as a gate dielectric material grown by atomic layer deposition (ALD). Hole mobility values of 1.5 ± 0.2 cm²/V s and 0.9 ± 0.1 cm²/V s were obtained when using heavily n-doped silicon (n⁺-Si) and ITO-coated glass as gate electrodes, respectively. These transistors were operated in enhancement mode with a zero turn-on voltage and exhibited a low threshold voltage (< −10 V) as well as a low sub-threshold slope (<1 V/decade) and an on/off current ratio larger than 10⁶. Atomic force microscopy (AFM) images of pentacene films on Al₂O₃ treated with octadecyltrichlorosilane (OTS) revealed well-ordered island formation, and X-ray diffraction patterns showed characteristics of a “thin film” phase. Low surface trap density and high capacitance density of Al₂O₃ gate insulators also contributed to the high performance of pentacene field-effect transistors.     

TiSiOx gate dielectrics produced by reactive sputtering for high performance InGaZnO thin film transistors

High dielectric constant TiSiOx thin films are produced by reactive sputtering under different oxygen partial pressure ratio (P_O2) from 15% to 30%. All the TiSiOx films show an excellent transmittance value of almost 95%. The TiSiOx film has a low leakage current density by optimizing oxygen partial pressure, and the leakage current density of TiSiOx film under P_O2 of 20% is 4.88×10⁻⁷ A/cm² at electrical field strength of 2 MV/cm. Meanwhile, their associated InGaZnO thin-film transistors (IGZO-TFTs) with different P_O2 TiSiOx thin films as gate insulators are fabricated. IGZO-TFTs under P_O2 of 20% shows an optimized electrical performance, and the threshold voltage, sub-threshold swing, field effect mobility and I_on/I_off ratio of this device are 2.22 V, 0.33 V/decade, 29.3 cm²/V s and 5.03×10⁷, respectively. Moreover, the density of states (DOS) is calculated by temperature-dependent field-effect measurement. The enhancements of electrical performance and temperature stability are attributed to better active/insulator interface and smaller DOS.     

Composition,structure and electrical properties of DC reactive magnetron sputtered Al2O3 thin films

Thin films of alumina (Al₂O₃) were deposited over Si 〈1 0 0〉 substrates at room temperature at an oxygen gas pressure of 0.03 Pa and sputtering power of 60 W using DC reactive magnetron sputtering. The composition of the as-deposited film was analyzed by X-ray photoelectron spectroscopy and the O/Al atomic ratio was found to be 1.72. The films were then annealed in vacuum to 350, 550 and 750 °C and X-ray diffraction results revealed that both as-deposited and post deposition annealed films were amorphous. The surface morphology and topography of the films was studied using scanning electron microscopy and atomic force microscopy, respectively. A progressive decrease in the root mean square (RMS) roughness of the films from 1.53 nm to 0.7 nm was observed with increase in the annealing temperature. Al–Al₂O₃–Al thin film capacitors were then fabricated on p-type Si 〈1 0 0〉 substrate to study the effect of temperature and frequency on the dielectric property of the films and the results are discussed.     

ZrO2 insulator modified by a thin Al2O3 film to enhance the performance of InGaZnO thin-film transistor

A high-performance InGaZnO (IGZO) thin-film transistor (TFT) with ZrO₂–Al₂O₃ bilayer gate insulator is fabricated. Compared to IGZO-TFT with ZrO₂ single gate insulator, its electrical characteristics are significantly improved, specifically, enhancement of I_on/I_off ratios by one order of magnitude, increase of the field-effect mobility (from 9.8 to 14 cm²/Vs), reduction of the subthreshold swing from 0.46 to 0.33 V/dec, the maximum density of surface states at the channel-insulator interface decreased from 4.3 × 10¹² to 2.5 × 10¹² cm⁻². The performance enhancements are attributed to the suppression of leakage current, smoother surface morphology, and suppression of charge trapping by using Al₂O₃ films to modify the high-k ZrO₂ dielectric.     

High performance sol–gel spin-coated titanium dioxide dielectric based MOS structures

High-κ TiO₂ thin films have been fabricated using cost effective sol–gel and spin-coating technique on p-Si (100) wafer. Plasma activation process was used for better adhesion between TiO₂ films and Si. The influence of annealing temperature on the structure-electrical properties of titania films were investigated in detail. Both XRD and Raman studies indicate that the anatase phase crystallizes at 400 °C, retaining its structural integrity up to 1000 °C. The thickness of the deposited films did not vary significantly with the annealing temperature, although the refractive index and the RMS roughness enhanced considerably, accompanied by a decrease in porosity. For electrical measurements, the films were integrated in metal-oxide-semiconductor (MOS) structure. The electrical measurements evoke a temperature dependent dielectric constant with low leakage current density. The Capacitance–voltage (C–V) characteristics of the films annealed at 400 °C exhibited a high value of dielectric constant (~34). Further, frequency dependent C–V measurements showed a huge dispersion in accumulation capacitance due to the presence of TiO₂/Si interface states and dielectric polarization, was found to follow power law dependence on frequency (with exponent ‘s’=0.85). A low leakage current density of 3.6×10⁻⁷ A/cm² at 1 V was observed for the films annealed at 600 °C. The results of structure-electrical properties suggest that the deposition of titania by wet chemical method is more attractive and cost-effective for production of high-κ materials compared to other advanced deposition techniques such as sputtering, MBE, MOCVD and ALD. The results also suggest that the high value of dielectric constant ‘κ‘ obtained at low processing temperature expands its scope as a potential dielectric layer in MOS device technology.     

Enhancement in electrical performance of indium gallium zinc oxide-based thin film transistors by low temperature thermal annealing

We have studied the characteristics of transparent bottom-gate thin film transistors (TFTs) using In–Ga–Zn–O (IGZO) as an active channel material. IGZO films were deposited on SiO₂/Si substrates by DC sputtering techniques. Thereafter, the bottom-gate TFT devices were fabricated by depositing Ti/Au metal pads on IGZO films, where the channel length and width were defined to be 200 and 1000 μm, respectively. Post-metallization thermal annealing of the devices was carried out at 260, 280 and 300 °C in nitrogen ambient for 1 h. The devices annealed at 280 °C have shown better characteristics with enhanced field-effect mobility and high on–off current ratio. The compositional variation of IGZO films was also observed with different annealing temperatures.     

Evaporated iron disulfide thin films with sulfurated annealing treatments

FeS₂ thin films were grown on a glass substrate using a physical vapor deposition technique at room temperature. Subsequently, the thin films were annealed in two different atmospheres: vacuum and vacuum-sulfur. In the vacuum-sulfur atmosphere a graphite box was used as sulfur container and the films were sulfurated successfully at 200–350 ºC. It was found that annealing in a vacuum-sulfur atmosphere was indispensable in order to obtain polycrystalline FeS₂ thin films. The polycrystalline nature and pure phase were determined by XRD and Raman techniques and the electrical properties by the Hall effect. Using the sulfurating technique, the n-type semiconductor was prepared at 200–350 °C and a p-type at 500 °C. The carrier concentrations were between 1.19×10²⁰ and 2.1×10²⁰ cm⁻³. The mobility was 9.96–5.25 cm² V⁻¹ s⁻¹ and the resistivity was 6.31×10⁻² to 1.089×10⁻² Ω cm. The results obtained from EDS showed that the films prepared in the vacuum-sulfur atmosphere were close to stoichiometric and that the indirect band gap varied between 1.03 and 0.945 eV.     

Role of ultrathin Al2O3 layer in organic/inorganic hybrid gate dielectrics for flexibility improvement of InGaZnO thin film transistors

We investigated flexible amorphous InGaZnO (a-IGZO) thin film transistors (TFTs) on a polyimide (PI) substrate by using organic/inorganic hybrid gate dielectrics of poly-4vinyl phenol (PVP) and ultrathin Al₂O₃. IGZO TFTs were fabricated with hybrid PVP/Al₂O₃ gate dielectrics having Al₂O₃ layers of different nanoscale thicknesses, which were deposited by atomic layer deposition (ALD). The electrical characteristics of the TFTs with the organic/inorganic hybrid gate dielectrics were measured after cyclic bending up to 1,00,000 cycles at the bending radius of 10 mm. The ultrathin Al₂O₃ layer in the hybrid gate dielectrics improved the mechanical flexibility and protected the organic gate dielectric against damage during the sputter deposition of the IGZO layer. Finite elements method (FEM) simulations along with the structural characterization of the cyclically bent device showed the importance of optimizing the thickness of the Al₂O₃ layer in the hybrid gate dielectrics to obtain mechanically stable and flexible a-IGZO TFTs.     

Complementary-like inverters based on an ambipolar solution-processed molecular bis(naphthalene diimide)-dithienopyrrole derivative

We report on high-mobility top-gate organic field-effect transistors (OFETs) and complementary-like inverters fabricated with a solution-processed molecular bis(naphthalene diimide)-dithienopyrrole derivative as the channel semiconductor and a CYTOP/Al₂O₃ bilayer as the gate dielectric. The OFETs showed ambipolar behavior with average electron and hole mobility values of 1.2 and 0.01 cm² V^?1 s^?1, respectively. Complementary-like inverters fabricated with two ambipolar OFETs showed hysteresis-free voltage transfer characteristics with negligible variations of switching threshold voltages and yielded very high DC gain values of more than 90 V/V (up to 122 V/V) at a supply voltage of 25 V.     

The correlation of γ-irradiation,particle size and their effects on physical properties of AgInSe2 nanostructure thin films

In this work the effect of γ-irradiation on the optical and electrical properties of near stoichiometric AgInSe₂ nanostructure thin films have been characterized. The XRD pattern of ingot AgInSe₂ powder prepared by solid state reaction showed tetragonal polycrystalline single-phase structure. The thin films of thickness 75 nm were prepared by inert gas condensation (IGC) technique at using constant Ar flow and substrate temperature of 300 K.Thin films were exposed to annealing process at 473 K for 2 h in vacuum of 10⁻² Torr. The amorphous and tetragonal nanocrystalline structures were detected for as-deposited and annealed films respectively by grazing incident in-plane X-ray diffraction (GIIXD) technique. The structure and average particle size of annealed irradiated films by different γ-doses from 0 to 4 Mrad were determined using high resolution transmission electron microscope (HRTEM). Optical transmission, reflection and absorption spectra were studied for both annealed unirradiated and irradiated films. Two optical transitions for each annealed unirradiated and film exposed to γ-irradiation doses from 0 to 4 Mrad were observed. The evaluated E_g1 due to 1^st transition have decreased from 1.52 to 1.44 eV and E_g2 due to 2^nd transition have decreased from 2.83 to 2.30 eV as the particle size increased from 7.3 to 9.5 nm by raising the irradiation dose up to 1 Mrad. The behavior of d.c. electrical conductivity with temperature that measured under vacuum was examined for all films under investigation. The evaluated activation energies due to irradiation doses are ranging from 0.58 to 0.68 eV.