Electrical,mechanical, structural,and thermal behaviors of polymeric gel electrolyte membranes of poly(vinylidene fluoride‐co‐hexafluoropropylene) with the ionic liquid 1‐butyl‐3‐methylimidazolium tetrafluoroborate plus lithium tetrafluoroborate

Polymeric gel electrolyte membranes based on the polymer poly(vinylidene fluoride‐co‐hexafluoropropylene) [P(VdF–HFP)] with different weight percentages of the ionic liquid (IL) 1‐butyl‐3‐methylimidazolium tetrafluoroborate plus 0.3M lithium tetrafluoroborate (LiBF₄) salt were prepared and characterized by scanning electron microscopy, X‐ray diffraction, differential scanning calorimetry, thermogravimetric analysis, Fourier transform infrared (FTIR) spectroscopy, complex impedance spectroscopy, pulse echo techniques, and Vickers hardness (H) testing. After the incorporation of the IL plus the salt solution in the P(VdF–HFP) polymer, the melting temperature, glass‐transition temperature (T_g), degree of crystallinity, thermal stability, elastic modulus (E), and hardness (H) gradually decreased with increasing content of the IL–salt solution as a result of complexation between the P(VdF–HFP) and IL. This was confirmed by FTIR spectroscopy. A part of the IL and LiBF₄ were found to remain uncomplexed as well. The ionic conductivity (σ) of the polymeric gel membranes was found to increase with increasing concentration of the IL–salt solution. The temperature‐dependent σs of these polymeric gel membranes followed an Arrhenius‐type thermally activated behavior. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41456.     

Thermogravimetric analysis of poly(3‐hydroxybutyrate) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)

The thermal degradation of poly(3‐hydroxybutyrate) (PHB) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) [P(HB‐HV)] was studied using thermogravimetry (TG). In the thermal degradation of PHB, the temperature at the onset of weight loss (T_o) was derived by T_o = 0.97B + 259, where B represents the heating rate (°C/min). The temperature at which the weight loss rate was maximum (T_p) was T_p = 1.07B + 273, and the final temperature (T_f) at which degradation was completed was T_f = 1.10B + 280. The percentage of the weight loss at temperature T_p (C_p) was 69 ± 1% whereas the percentage of the weight loss at temperature T_f (C_f) was 96 ± 1%. In the thermal degradation of P(HB‐HV) (7:3), T_o = 0.98B + 262, T_p = 1.00B + 278, and T_f = 1.12B + 285. The values of C_p and C_f were 62 ± 7 and 93 ± 1%, respectively. The derivative thermogravimetric (DTG) curves of PHB confirmed only one weight loss step change because the polymer mainly consisted of the HB monomer only. The DTG curves of P(HB‐HV), however, suggested multiple weight loss step changes; this was probably due to the different evaporation rates of the two monomers. The incorporation of 10 and 30 mol % of the HV component into the polyester increased the various thermal temperatures (T_o, T_p, andT_f) by 7–12°C (measured at B = 20°C/min). © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2237–2244, 2001     

Efficient synthesis of organic carbonates and poly(1,4‐butylene carbonate‐co‐terephthalate)s

Dimethyl carbonate (DMC) is an environmentally benign chemical currently produced using CO₂. Using the conventional Dean–Stark apparatus, a method was developed for the effective and selective removal of the methanol generated in the transesterification of DMC with alcohol. Using this device, various diols (HO‐A‐OH; A = (CH₂)₄, (CH₂)₂O(CH₂)₂, CH₂C₆H₁₀CH₂, and CH₂C₆H₄CH₂) were converted to mixtures of the corresponding MeOC(O)[O‐A‐OC(O)]OMe and MeOC(O)[O‐A‐OC(O)]₂OMe. Dialkyl carbonates such as dibutyl carbonate, dibenzyl carbonate, and diallyl carbonate were also efficiently prepared from the corresponding alcohols using this device. The compound prepared from 1,4‐butanediol, MeOC(O)[O(CH₂)₄OC(O)]_1.5OMe, was subjected to polycondensation with HO(CH₂)₄[O₂CC₆H₄CO₂(CH₂)₄]_1.5OH or HO(CH₂)₄[O₂CC₆H₄CO₂(CH₂)₄]_1.8OH, which directly was prepared from terephthalic acid and 1,4‐butanediol. The polycondensation afforded high‐molecular‐weight poly(1,4‐butylene carbonate‐co‐terephthalate)s (PBCTs) with M_w of 80–270 kDa and 0.40–0.46 terephthalate mole fractions. PBCTs are attractive materials with potential biodegradability and LDPE‐like thermal properties. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44951.     

Using hydroxypropyl‐β‐cyclodextrin for the preparation of hydrophobic poly(ketoethyl methacrylate) in aqueous medium

This work was committed to the polymerization of hydrophobic ketoethyl methacrylate monomer in aqueous medium in the presence of cyclodextrin, instead of polymerizing the monomer in toxic and volatile organic solvents. For this purpose, a new ketoethyl methacrylate monomer, p‐methylphenacylmethacrylate (MPMA), was synthesized from the reaction of p‐methylphenacylbromide with sodium methacrylate in the presence of triethylbenzylammonium chloride. The monomer was identified with FTIR, ¹H and ¹³C‐NMR spectroscopies. Hydroxypropyl‐β‐cyclodextrin (HPCD) was used to form a water‐soluble host/guest inclusion complex (MPMA/HPCD) with the hydrophobic monomer. The complex was identified with FTIR and NMR techniques and polymerized in aqueous medium using potassium persulfate as initiator. During polymerization the resulting hydrophobic methacrylate polymer precipitated out with a majority of HPCD left in solution and a minority of HPCD bonded on the resulting polymer. The thus‐prepared polymer exhibited little difference from the counterparts obtained in organic solvent in number average molecular weight (M_n), polydispersity (M_w/M_n) and yield. The investigation provides a novel strategy for preparing hydrophobic ketoethyl methacrylate polymer in aqueous medium by using a monomer/HPCD inclusion complex. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and properties of new novolacs based on heteroatom‐bridged phenol derivatives

We describe the synthesis and properties of new novolacs prepared by addition‐condensation of heteroatom‐bridged phenol derivatives and formaldehyde. The trifluoroacetic acid‐catalyzed polymerization of equimolar amounts of bis(4‐methoxyphenyl) ether ( 1a ) and formaldehyde proceeded homogeneously to afford the polymer ( 2a ) in 49% yield (M_n 2600, M_w/M_n 1.8). From the FTIR, ¹H‐NMR, and ¹³C‐NMR spectra of 2a , it was evident that the polymer had methylene moieties‐bridged repeating units in the polymer backbone. A higher molecular weight novolac ( 2a ′) (yield 99%, M_n 16,600, M_w/M_n 12.9) could be prepared by using an excess of formaldehyde. Bis(4‐methoxyphenyl) sulfone novolac ( 2b ) (M_n 1300, M_w/M_n 1.2) and bis(4‐methoxyphenyl) sulfide novolac ( 2d ) (M_n 1200, M_w/M_n 1.9) were also prepared. However, the polymerization of bis(4‐hydroxyphenyl) sulfone ( 1c ) did not proceed, even when it was attempted under various reaction conditions. From TGA, the temperatures at 10% loss in weight (T₁₀) for 2a , 2a ′, and 2b were found to be 413, 430 and 393°C, respectively. These results suggested that heteroatom‐bridged novolacs based on phenol derivatives have good thermal stability than other organosoluble polymers; moreover, these novolacs could be expected to function as processable materials, polymer blends for engineering plastics, etc. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

New fluorine‐containing bissalicylidenimine–titanium complexes for olefin polymerization

Three new titanium complexes bearing salicylidenimine ligands—bis[(salicylidene)‐2,3,5,6‐tetrafluoroanilinato]titanium(IV) dichloride ( 1 ), bis[(3,5‐di‐tert‐butylsalicylidene)‐2,3,5,6‐tetrafluoroanilinato]titanium(IV) dichloride ( 2 ), and bis[(3,5‐di‐tert‐butylsalicylidene)‐4‐trifluoromethyl‐2,3,5,6‐tetrafluoroanilinato]titanium(IV) dichloride ( 3 )—were synthesized. The catalytic activities of 1 – 3 for ethylene polymerization were studied with poly(methylaluminoxane) (MAO) as a cocatalyst. Complex 1 was inactive in ethylene polymerization. Complex 2 at a molar ratio of cocatalyst to pre catalyst of Al_MAO/Ti = 400–1600 showed very high activity in ethylene polymerization comparable to that of the most efficient metallocene complexes and titanium compounds with phenoxy imine and indolide imine chelating ligands. It gave linear high‐molecular‐weight polyethylene [weight‐average molecular weight (M_w) ≥ 1,700,000. weight‐average molecular weight/number‐average molecular weight (M_w/M_n) = 4–5] with a melting point of 142°C. The ability of the 2 /MAO system to copolymerize ethylene with hexene‐1 in toluene was analyzed. No measurable incorporation of the comonomer was observed at 1:1 and 2:1 hexene‐1/ethylene molar ratios. However, the addition of hexene‐1 had a considerable stabilizing effect on the ethylene consumption rate and lowered the melting point of the resultant polymer to 132°C. The 2 /MAO system exhibited low activity for propylene polymerization in a medium of the liquid monomer. The polymer that formed was high‐molecular‐weight atactic polypropylene (M_w ～ 870,000, M_w/M_n = 9–10) showing elastomeric behavior. The activity of 3 /MAO in ethylene polymerization was approximately 70 times lower than that of the 2 /MAO system. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1040–1049, 2005     

Schiff base‐substituted polyphenol: synthesis,characterisation and non‐isothermal degradation kinetics

BACKGROUND: Polymers of phenols and aromatic amines have emerged as new materials in fields such as superconductors, coatings, laminates, photoresists and high‐temperature environments. The stability, kinetics and associated pollution of the thermal decomposition of oligophenols are of interest for the aforementioned fields. RESULTS: A new Schiff base polymer, derived from N,N′‐bis(2‐hydroxy‐3‐methoxyphenylmethylidene)‐2,6‐pyridinediamine, was prepared by oxidative polycondensation. Characterisations using Fourier transform infrared, UV‐visible, ¹H NMR and ¹³C NMR spectroscopy, thermogravimetric/differential thermal analysis, gel permeation chromatography, cyclic voltammetry and conductivity measurements were performed. The number‐average (M_n) and weight‐average molecular weight (M_w) and dispersity (D = M_w/M_n) of the polymer were found to be 61 000 and 94 200 g mol^?1 and 1.54, respectively. Apparent activation energies of the thermal decomposition of the polymer were determined using the Tang, Flynn–Wall–Ozawa, Kissinger–Akahira–Sunose and Coats–Redfern methods. The most likely decomposition process was a D_n deceleration type in terms of the Coats–Redfern and master plot results. CONCLUSION: The mechanism of the degradation process can be understood through the use of kinetic parameters obtained from various non‐isothermal methods. Copyright © 2009 Society of Chemical Industry     

Synthesis,characterization, and antimicrobial properties of oligo‐4‐[(pyridine‐3‐yl‐methylene) amino] phenol

The oxidative polycondensation reaction conditions of 4‐[(pyridine‐3‐yl‐methylene) amino]phenol (4‐PMAP) were studied using H₂O₂, atmospheric O₂, and NaOCl oxidants in an aqueous alkaline medium between 30°C and 90°C. Synthesized oligo‐4‐[(pyridine‐3‐yl‐methylene) amino] phenol (O‐4‐PMAP) was characterized by ¹H‐, ¹³C NMR, FTIR, UV–vis, size exclusion chromatography (SEC), and elemental analysis techniques. The yield of O‐4‐PMAP was found to be 32% (for H₂O₂ oxidant), 68% (for atmospheric O₂ oxidant), and 82% (for NaOCl oxidant). According to the SEC analysis, the number–average molecular weight, weight–average molecular weight, and polydispersity index values of O‐4‐PMAP was found to be 5767, 6646 g mol^?1, and 1.152, respectively, using H₂O₂, and 4540, 5139 g mol^?1, and 1.132, respectively, using atmospheric O₂, and 9037, 9235 g mol^?1, and 1.022, using NaOCl, respectively. According to TG and DSC analyses, O‐4‐PMAP was more stable than 4‐PMAP against thermal decomposition. The weight loss of O‐4‐PMAP was found to be 94.80% at 1000°C. Also, antimicrobial activities of the oligomer were tested against B. cereus, L. monocytogenes, B. megaterium, B. subtilis, E. coli, Str. thermophilus, M. smegmatis, B. brevis, E. aeroginesa, P. vulgaris, M. luteus, S. aureus, and B. jeoreseens. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3327–3333, 2006     

Molecular weight development in emulsion copolymerization of n‐butyl acrylate and styrene

The seeded emulsion copolymerization of n‐butyl acrylate and styrene in a weight ratio of 50/50 was investigated. The effect of the type of process (batch vs. semicontinuous) and the amounts of initiator and emulsifier charged into the reactor on the time evolution of the fractional conversion, number of polymer particles, and weight‐average molecular weight (M_w) was analyzed. It was found that the M_w depends to a slight extent on the type of process and the emulsifier concentration and to a larger extent on the initiator concentration. The molecular weight distributions (MWDs) and the gel content of the final latexes were also analyzed. In the absence of chain transfer agents (CTAs), the fraction of gel was higher in the semicontinuous processes. It was also found that the gel content increased with increasing initiator concentration in the recipe. The addition of 1 wt % CTA avoided gel formation and led to an important reduction of the M_w. Nevertheless, the MWDs presented a shoulder or even a second peak at high molecular weights that was due to reactions of chain transfer to the polymer. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1918–1926, 2003     

Rheological and thermal properties of saponified cassava starch‐g‐poly(acrylamide) superabsorbent polymers varying in grafting parameters and absorbency

Cassava starch‐graft‐poly(acrylamide) superabsorbent polymers (SAPs) with varying absorbencies were synthesized. Weight average molecular weight (M_w) of the hydrolyzed starch‐graft‐copolymers ranged from 1.6 × 10⁶ to 2.8 × 10⁶ g/mol, the largest being shown by the sample with highest percentage grafting. The storage (G′) and loss modulus (G″) of hydrogels were determined as a function of frequency. G″ was larger than G′ for the hydrogels with higher absorbencies and exhibited a liquid‐like behavior. However, hydrogels with lower absorbencies showed a reverse viscoelastic behavior. The viscosity of hydrogels determined using a Brookfield viscometer at different shear rates was found to be larger for the hydrogels with higher absorbencies. The melting temperature (T_m) and enthalpy change of fusion (ΔH_f) of the SAPs ranged from 149.7 to 177.7°C and 65 to 494.9 J/g, respectively and showed a positive correlation with grafting parameters and M_w. Heavy metal ion removal capacity of hydrogel followed the order Cu²⁺ > Pb²⁺ > Zn²⁺. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40368.     

Light‐scattering study of poly(hydroxy ester ether) in N,N‐dimethylacetamide solution

Static and dynamic light‐scattering techniques were used to study biodegradable thermoplastic poly(hydroxy ester ether) in N,N‐dimethylacetamide (DMAc). A weight‐average molecular weight M_W = 6.4 × 10⁴ g/mol, radius of gyration R_G = 9.4 nm, second‐virial coefficient A₂ = 1.05 × 10^?3 mol mL/g², translational diffusion coefficient D = 1.34 × 10^?7 cm²/s, and hydrodynamic radius R_H = 8.3 nm are reported. In addition, the effect of H₂O on the polymer chain's conformation and architecture in a DMAc/H₂O solution is evaluated. Results suggest that H₂O makes the mixed solvent poorer as well as promotes polymer chain branching via intramolecular transesterification. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1737–1745, 2001     

Synthesis and characterization of ternary‐copolymer of soluble fluorinated polyimides based on 1,4‐bis (4‐amino‐2‐trifluoromethylphenoxy) benzene

A series of novel ternary‐copolymer of fluorinated polyimides (PIs) were prepared from 1,4‐bis(4‐amino‐2‐trifluoromethylphenoxy)benzene (pBATB), commercially available aromatic dianhydrides, and aromatic diamines via a conventional two‐step thermal or chemical imidization method. The structures of all the obtained PIs were characterized with FTIR, ¹H‐NMR, and element analysis. Besides, the solubility, thermal stability, mechanical properties, and moisture uptakes of the PIs were investigated. The weight‐average molecular weight (M_w) and the number‐average molecular weight (M_n) of the PIs were determined using gel‐permeation chromatography (GPC). The PIs were readily dissolved not only in polar solvents such as DMF, DMAc, and NMP, but also in some common organic solvents, such as acetic ester, chloroform, and acetone. The glass transition temperatures of these PIs ranged from 201 to 234°C and the 10% weight loss temperatures ranged from 507 to 541°C in nitrogen. Meanwhile, all the PIs left around 50% residual even at 800°C in nitrogen. The GPC results indicated that the PIs possessed moderate‐to‐high number‐average molecular weight (M_n), ranging from 9609 to 17,628. Moreover, the polymer films exhibited good mechanical properties, with elongations at break of 8–21%, tensile strength of 66.5–89.8 MPa, and Young's modulus of 1.04–1.27 GPa, and low moisture uptakes of 0.54–1.13%. These excellent combination properties ensure that the polymer could be considered as potential candidates for photoelectric and microelectronic applications. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Rapid living free‐radical polymerization of methyl acrylate under 60Co γ‐ray irradiation at room temperature

Rapid living free‐radical polymerization of methyl acrylate under ⁶⁰Co γ‐ray irradiation in the presence of benzyl 1H‐imidazole‐1‐carbodithioate at room temperature is reported. The results showed that the polymerization is a fast living process, and that the molecular weight of the polymer is as high as 39 600 g mol^?1 at 68 % conversion with M_w/M_n = 1.09 within 68 min. The polymerization rate was markedly influenced by the structures of thiocarbonylthio compounds. Copyright © 2004 Society of Chemical Industry     

Mechanisms and kinetics of thermal degradation of poly(butylene succinate‐co‐propylene succinate)s

Poly(butylene succinate) (PBSu) and two PBSu‐rich poly(butylene succinate‐co‐propylene succinate)s were studied. Copolyesters were characterized as random copolymers, based on ¹³C‐NMR spectra. TGA‐FTIR was used to monitor the degradation products at a heating rate of 5°C/min under N₂. FTIR spectra revealed that the major products were anhydrides, which were formed following two cyclic intramolecular degradation mechanisms by the breaking of the weak O‐CH₂ bonds around succinate groups. Thermal stability at heating rates of 1, 3, 5, and 10°C/min under N₂ was investigated using TGA. The model‐free methods of the Friedman and Ozawa equations are useful for studying the activation energy of degradation in each period of mass loss. The results reveal that the random incorporation of minor propylene succinate units into PBSu did not markedly affect their thermal resistance. Two model‐fitting mechanisms were used to determine the mass loss function f(α), the activation energy and the associated mechanism. The mechanism of autocatalysis nth‐order, with f(α) = α^m(1 ? α)ⁿ, fitted the experimental data much more closely than did the nth‐order mechanism given by f(α) = (1 ? α)ⁿ. The obtained activation energy was used to estimate the failure temperature (T_f). The values of T_f for a mass loss of 5% and an endurance time of 60,000 h are 160.7, 155.5, and 159.3°C for PBSu and two the copolyesters, respectively. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Mechanical and chemical properties of poly(styrene‐isobutylene‐styrene) block copolymers: Effect of sulfonation and counter ion substitution

In this study, the mechanical and chemical properties of a series of sulfonated poly(styrene‐isobutylene‐styrene) (SIBS) block copolymers were evaluated using a combination of nanoindentation, dynamic mechanical analysis (DMA), elemental analysis (EA), Fourier transform infrared spectroscopy (FTIR), water absorption, and small angle X‐ray scattering studies (SAXS). The materials properties were characterized as a function of the sulfonation percent in the block copolymers, as well as a result of the counter‐ion substitution with Mg²⁺, Ca²⁺, and Ba²⁺. Nanoindentation studies revealed that the elastic modulus (E) and hardness (H) increase with sulfonation up to a certain level, at which point, the effect of water content further hinders any mechanical reinforcement. The incorporation of counter‐ions increases E and H, but the results are dependent upon the size of the counter‐ion. DMA results showed that the polymer maintained the glass transition temperature (T_g) of the polyisobutylene (PIB) segment (?60°C) regardless of the sulfonation level or counter‐ion substituted. However, both the shoulder of the PIB T_g (?30°C), which was probably caused by a Rouse‐type motion, as well as the T_g of polystyrene (105°C) disappeared upon sulfonation. Counter‐ion substitution increased the storage modulus of the rubbery plateau, which is indicative of a stronger and more thermally stable crosslinked complex formation. Additional unique relaxations were observed with the counter‐ions, and could be attributed to the stretching/rotation of the S? O bond and the interaction of the cations with the oxygen in the sulfonic group. FTIR results also revealed a unique shifting of the asymmetric S? O band when counter‐ions were added. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40344.     

Synthesis,characterization, conductivity,band gap,and kinetic of thermal degradation of poly‐4‐[(2‐mercaptophenyl) imino methyl] phenol

The oxidative polycondensation reaction conditions of 4‐[(2‐mercaptophenyl) imino methyl] phenol (2‐MPIMP) were studied in an aqueous acidic medium between 40 and 90°C by using oxidants such as air, H₂O₂, and NaOCl. The structures of the synthesized monomer and polymer were confirmed by FTIR, ¹H NMR, ¹³C NMR, and elemental analysis. The characterization was made by TGA‐DTA, size exclusion chromatography (SEC) and solubility tests. At the optimum reaction conditions, the yield of poly‐4‐[(2‐mercaptophenyl) imino methyl]phenol (P‐2‐MPIMP) was found to be 92% for NaOCl oxidant, 84% for H₂O₂ oxidant 54% for air oxidant. According to the SEC analysis, the number‐average molecular weight (M_n), weight‐average molecular weight (M_w), and polydispersity index values of P‐2‐MPIMP were found to be 1700 g mol^?1, 1900 g mol^?1, and 1.118, using H₂O₂; 3100 g mol^?1, 3400 g mol^?1, and 1.097, using air; and 6750 g mol^?1, 6900 g mol^?1, and 1.022, using NaOCl, respectively. According to TG analysis, the weight losses of 2‐MPIMP and P‐2‐MPIMP were found to be 95.93% and 76.41% at 1000°C, respectively. P‐2‐MPIMP showed higher stability against thermal decomposition. Also, electrical conductivity of the P‐2‐MPIMP was measured, showing that the polymer is a typical semiconductor. The highest occupied molecular orbital, the lowest unoccupied molecular orbital, and the electrochemical energy gaps (E′_g) of 2‐MPIMP and P‐2‐MPIMP were found to be ?6.13, ?6.09; ?2.65, ?2.67; and 3.48, 3.42 eV, respectively. Kinetic and thermodynamic parameters of these compounds investigated by MacCallum‐Tanner and van Krevelen methods. The values of the apparent activation energies of thermal decomposition (E_a), the reaction order (n), pre‐exponential factor (A), the entropy change (ΔS*), enthalpy change (ΔH*), and free energy change (ΔG*) were calculated from the TGA curves of compounds. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis,photo‐, and electroluminescent properties of the soluble poly[(2,5‐diphenylene‐1,3,4‐oxadiazole)‐ 4,4′‐vinylene]

A novel soluble conjugated polymer, poly[(2,5‐diphenylene‐1,3,4‐oxadiazole)‐4,4′‐vinylene] (O‐PPV), containing an electron‐transporting group on the main chain of PPV, was synthesized according to HORNER mechanism. The oligo‐polymer with M_w = 1000 and T_d = 270°C is soluble in chloroform and tetrahydrofuran. The photoluminescent (PL) properties were investigated using different concentrations of solid‐state O‐PPV/PEO blends absorption and selective excitation measurements. The results show that PL arises from interchain charge‐transfer states in solid‐state O‐PPV. Compared with the analogous single‐layer device constructed with PPV (ITO/PPV/Al), which emits two peaks at λ = 520 nm and 550 nm (shoulder), the electroluminescence (EL) spectrum of the device [ITO/O‐PPV (80 nm)/Al] is a broad peak at λ_max = 509 nm. The quantum efficiency (0.13%) of the device ITO/O‐PPV/Al is much higher than that of the device ITO/PPV/Al, due to the introduction of the electron‐transporting group–oxadiazole units in the main chain of PPV. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 3535–3540, 1999     

Semicontinuous emulsion copolymerization of 3‐O‐methacryloyl‐1,2:5,6‐di‐O‐isopropylidene‐α‐D‐glucofuranose (3‐MDG) and butyl acrylate (BA). Monomer feed addition

New polymer colloids based on the saccharide monomer, using of 3‐O‐methacryloyl‐1,2:5,6‐di‐O‐isopropylidene‐α‐D ‐glucofuranose (3‐MDG), were prepared by semicontinuous emulsion polymerization, a widely used industrial process. The copolymerization of 3‐MDG and butyl acrylate (BA), by the monomer‐addition technique, at 70°C, using sodium persulfate (Na₂S₂O₈) as an initiator, was investigated. The influence of some reaction parameters, such as the type and concentration of the surfactants as well as the monomer addition rate (R_m) on the polymerization rate (R_p), the colloidal properties, and the stability of the latexes, was studied. It was found that under starved‐feed conditions the polymerization rate and the particle size (D) increased with an increasing rate of monomer addition. The weight‐average molecular weight (M _w) also increased by enhancing R_m and a narrower molecular weight distribution was obtained. Furthermore, the type and the concentration of the surfactants strongly influenced the particle size and its distribution. The effect of the seed stage on the particle size and its distribution was also investigated. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2091–2102, 2003     

Polybenzimidazole (PBI) molecular weight and Mark‐Houwink equation

The molecular weight, and intrinsic viscosity of polybenzimidazole (PBI) and its phosphonylated derivatives are reported. The relationship between intrinsic viscosity [η] and weight average molecular weight (M_w) for PBI has been established in H₂SO₄ and DMF‐LiCl. The Mark Houwink constants K_w of 5.2 × 10^?3 mL/g, α of 0.92 for H₂SO₄ solvent systems and, K_w of 3.2 × 10^?2 mL/g, α of 0.754 for DMF‐LiCl solvent system have been determined at M_w < 65,000. The intrinsic viscosity of PBI determined by the Huggins–Kraemer method was compared with a single point method, and found that both methods fit well for PBI in relatively low concentration solvent system, giving ～ 99% accuracy. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Poly‐2‐[(4‐methylbenzylidene)amino]phenol: Investigation of thermal degradation and antimicrobial properties

A new polyphenol (poly‐2‐[(4‐methylbenzylidene)amino]phenol) (P(2‐MBAP)) containing an azomethine group was synthesized by oxidative polycondensation reaction of 2‐[(4‐methylbenzylidene)amino]phenol (2‐MBAP) with NaOCl, H₂O₂, and O₂ oxidants in an aqueous alkaline medium. The structures of 2‐MBAP and P(2‐MBAP) were characterized by UV‐vis, FT‐IR, and ¹H NMR spectra. While the monomer decomposed completely up to 350°C and 57.2% of the polymer decomposed up to 1000°C. The thermal degradation of P(2‐MBAP) was also supported by the Thermo‐IR spectra recorded in the temperature range of 25–800°C. Electrical conductivity of the polymer was observed to increase 10⁸ fold after doping with I₂. Antimicrobial activities of the P(2‐MBAP) and 2‐MBAP against Sarcina lutea, Enterobacter aerogenes, Escherichia coli, Enterococcus feacalis, Klebsiella pneumoniae, Bacillus subtilis, Candida albicans, and Saccharomyces cerevisiae were also investigated. The number average molecular weight (M_n), weight average molecular weight (M_w) and polydispersity index (PDI) of the polymers were determined by gel permeation chromatography (GPC). © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41758.