Alternating block copolymers based on polyamide‐12 and polycaprolactone

A series of alternating polyester/polyamide block copolymers were prepared by sequential conversion of hydroxy‐terminated polycaprolactone and amino‐terminated polyamide‐12 with a selectively reacting coupling agent. The thermal properties of the block copolymers were investigated using differential scanning calorimetry and dynamic mechanical analysis. Mechanical properties were determined using tensile and impact tests. All polymers were phase‐separated, where the polyamide phase was semicrystalline in all compositions. Distinct crystallization of the polycaprolactone phase was observed only when the block length was greater than 2000 g mol^?1. Mechanical testing showed that the polymers behave in a manner similar to that of thermoplastic elastomers. In particular, samples with a high content of polycaprolactone showed high strain and good impact behaviour. Copyright © 2011 Society of Chemical Industry     

Study of the dielectric relaxation of poly(phenylpropyl acrylate) and poly(phenylpropyl methacrylate): effect of slight differences in chemical structure

A comparative study of the dielectric relaxational behaviour of two structurally close polymers, containing aromatic side groups, was carried out in order to analyse how slight differences in the chemical structure affect the molecular responses to perturbation field. Specifically, poly(phenylpropyl acrylate) (P3Ph1PA) and poly(phenylpropyl methacrylate) (P3Ph1PM) were studied using differential scanning calorimetry and dielectric relaxation spectroscopy in the frequency range 10^?2–10⁶ Hz and temperature window of ?80 to 120 °C. Both techniques show one glass–rubber transition for P3Ph1PA and two for P3Ph1PM, which evidence the great effect of the methyl groups on the segmental motions of the polymer. Phenomenological analysis of the data was carried out in order to establish the strength, width and fragility parameters of the glass–rubber transitions. In the case of P3Ph1PA, the strength is found to be larger than for P3Ph1PM, pointing out that the methyl group disturbs the mobility. Conductive processes dominate the dielectric spectra at high temperatures and low frequencies. © 2015 Society of Chemical Industry     

Viscoelasticity and morphology of poly(ethylene‐co‐vinyl acetate)/polyisobutylene blends

Blends of an ethylene/vinyl acetate copolymer (EVA) and polyisobutylene of various compositions were prepared by mechanical mixing at a temperature above the melting point of EVA (T_m^EVA) but below the upper critical solution temperature of 170°C for given blends. The rheological properties of the components and blends were studied in the region of small‐amplitude oscillating deformation at temperatures above and below T_m^EVA in the frequency range of 0.01–100 rad/s. At temperatures lower than T_m^EVA, the rheological properties were determined by the existence of the yield stress. With diminishing frequency, the viscosity increased, and the plateau in the relaxation spectrum at low frequencies broadened. The morphology of the blends depended on the conditions of sample heating. The introduction of a finely dispersed filler into the blends led to an anomalous drop in the viscosity. The morphology of the systems that arose by mechanical blending of the molten components was the important factor in the rheological behavior. The observed effects were examined in the framework of the concept of structural networks formed in melts by nonmelted crystallites of EVA. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2700–2707, 2006     

Thermoplastic natural rubber based on polyamide‐12: Influence of blending technique and type of rubber on temperature scanning stress relaxation and other related properties

Thermoplastic natural rubber based on polyamide‐12 (PA‐12) blend was prepared by melt blending technique. Influence of blending techniques (i.e., simple blend and dynamic vulcanization) and types of natural rubber (i.e., unmodified natural rubber (NR) and epoxidized natural rubber (ENR)) on properties of the blends were investigated. It was found that the simple blends with the proportion of rubber ～ 60 wt % exhibited cocontinuous phase structure while the dynamically cured blends showed dispersed morphology. Furthermore, the blend of ENR exhibited superior mechanical properties, stress relaxation behavior, and fine grain morphology than those of the blend of the unmodified NR. This is attributed to chemical interaction between oxirane groups in ENR molecules and polar functional groups in PA‐12 molecules which caused higher interfacial adhesion. It was also found that the dynamic vulcanization caused enhancement of strength and hardness properties. Temperature scanning stress relaxation measurement revealed improvement of stress relaxation properties and thermal resistance of the dynamically cured ENR/PA‐12 blend. This is attributed to synergistic effects of dynamic vulcanization of ENR and chemical reaction of the ENR and PA‐12 molecules. Furthermore, the dynamically cured ENR/PA‐12 blend exhibited smaller rubber particles dispersed in the PA‐12 matrix. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of poly(styrene‐co‐maleic anhydride) imidization on the miscibility and phase‐separation temperatures of poly(styrene‐co‐maleic anhydride)/poly(vinyl methyl ether) and poly(styrene‐co‐maleic anhydride)/ poly(methyl methacrylate) blends

The objective of this work was to study the miscibility and phase‐separation temperatures of poly(styrene‐co‐maleic anhydride) (SMA)/poly(vinyl methyl ether) (PVME) and SMA/poly(methyl methacrylate) (PMMA) blends with differential scanning calorimetry and small‐angle light scattering techniques. We focused on the effect of SMA partial imidization with aniline on the miscibility and phase‐separation temperatures of these blends. The SMA imidization reaction led to a partially imidized styrene N‐phenyl succinimide copolymer (SMI) with a degree of conversion of 49% and a decomposition temperature higher than that of SMA by about 20°C. We observed that both SMI/PVME and SMI/PMMA blends had lower critical solution temperature behavior. The imidization of SMA increased the phase‐separation temperature of the SMA/PVME blend and decreased that of the SMA/PMMA blend. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Comparison of the enthalpic relaxation of poly(lactide–co‐glycolide) 50:50 nanospheres and raw polymer

The phenomenon of enthalpic relaxation was evaluated for poly(lactide‐co‐glycolide) (PLGA, 50:50), in terms of storage of nanospheres for use as a controlled drug delivery system. Samples were stored for different times and temperatures below the glass transition temperature (T_g). Relaxation occurred at a significant rate up to 15 degrees below the T_g of 39.2°C. The effect of polymer morphology was considered by comparing the relaxation kinetics of the raw polymer with that of nanospheres formed using a novel technique. The nanospheres were shown to have a larger change in heat capacity at the glass transition and a longer average relaxation time than that of the raw polymer, and the relationship between these two parameters was discussed. For both the raw polymer and the nanospheres, relaxation was found to occur at a significant rate at room temperature. The storage of this system at subambient temperatures was therefore deemed important for maintaining the physicochemical properties of the system. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1868–1872, 2002     

Preparation and properties of poly(ether‐ester‐amide)/poly(acrylonitrile‐co‐butadiene‐co‐styrene) antistatic blends

A novel antistatic agent poly(ether‐ester‐amide) (PEEA) based on caprolactam, polyethylene glycol, and 6‐aminocaproic acid was successfully synthesized by melting polycondensation. The structure, thermal properties, and antistatic ability of the copolymer were characterized by Fourier transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analyses, and ZC36 megohmmeter. Test results show that PEEA is a block copolymer with a melting point of 217°C and a thermal decomposition temperature of 409°C, together with a surface resistivity of 10⁸ Ω/sq. Antistatic poly(acrylonitrile‐co‐butadiene‐co‐styrene) (ABS) materials were prepared by blending different content of PEEA to ABS resin. The antistatic performances, morphology, and mechanical properties were investigated. It is indicated that the surface resistivity of PEEA/ABS blends decrease with the increasing PEEA content, and the excellent antistatic performance is obtained when the antistatic agent is up to 10–15%. The antistatic performance is hardly influenced by water‐washing and relative humidity, and a permanent antistatic performance is available. The antistatic mechanism is investigated. The compatibility of the blends was studied by scanning electron microscopy images. The ladder distribution of antistatic agent is formed, and a rich phase of antistatic agent can be found in the surface layer. The elongations at break of the blend are improved with the increasing antistatic agent; the tensile strength and the notched impact strength kept almost the same. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Study on the synthesis of poly(ether‐block‐amide) copolymer based on nylon6 and poly(ethylene oxide) with various block lengths

Various segmented block copolyetheramides based on nylon6 (N6) and poly(ethylene oxide) (PEO) with different compositions and block length of the hard and soft segments were synthesized. The effect of composition of the hard and soft segments was studied via FTIR spectroscopy based on the characteristic peak of ester group at wave number of 1730 cm^?1. The average block length of the hard and soft segments in block copolymers was determined from H‐NMR analysis. Differential thermal analysis thermograms confirmed a microphase separated morphology over a broad range of temperature, leading to two separated crystalline domains. An increase in the interconnectivity of the polyamide segments controlled by chain extension, greatly improved the formation of polyamide lamellae crystals determined by X‐ray diffractometry. Atomic force microscopy images indicated different morphologies of dispersed phase in the dominant phase, which plays an important role in their performance for membrane processes. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of biodegradable block copolymers of poly(propylene fumarate‐co‐sebacate)‐co‐poly(ethylene glycol) and poly(ethylene fumarate‐co‐sebacate)‐co‐poly(ethylene glycol)

The synthesis of two low molecular weight linear unsaturated oligoester precursors, poly(propylene fumarate‐co‐sebacate) (PPFS) and poly(ethylene fumarate‐co‐sebacate) (PEFS), are described. PPFS, PEFS, and poly(ethylene glycol) are then used to prepare poly(propylene fumarate‐co‐sebacate)‐co‐poly(ethylene glycol) (PPFS‐co‐PEG) and poly(ethylene fumarate‐co‐sebacate)‐co‐poly(ethylene glycol) (PEFS‐co‐PEG) block copolymers. The products thus obtained are investigated in terms of the molecular weight, composition, structure, thermal properties, and solubility behavior. A number of design parameters including the molecular weights of PPFS, PEFS, and PEG, the reaction time in the polymer synthesis, and the weight ratio of PEG to PPFS or to PEFS are varied to assess their effects on the product yield and properties. The hydrolytic degradation of PPFS‐co‐PEG and PEFS‐co‐PEG in an isotonic buffer (pH 7.4, 37°C) is investigated, and it is found that the fumarate ester bond cleaves faster than does the sebacate ester bond. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 295–300, 2004     

Degradation kinetics of poly(HDDA‐co‐MMA)

1,6‐hexanediol diacrylate (HDDA) and methyl methacrylate (MMA) were copolymerized in different weight ratios using UV light induced photo‐polymerization to give poly(HDDA‐co‐MMA). Differential scanning calorimetry shows that copolymer was formed. The thermogravimetric and differential scanning calorimetric studies with different heating rates were carried out on these copolymers to understand the nature of degradation and to determine its kinetics. Different kinetic models were adopted to evaluate various parameters like the activation energy, the order, and the frequency factor. These analyses are important to study the binder removal from 3D‐shaped ceramic objects made by techniques like Solid free form fabrication. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Influence of various reaction media on the thermal and rheological properties of poly(acrylamide‐co‐N‐hexadecylacrylamide)

A hydrophobically modified polyacrylamide (PAM) was synthesized by the copolymerization of acrylamide (Am) and N‐hexadecylacrylamide (hAm) through solution copolymerization in a polar organic solvent. Polymer synthesis was performed in three nonaqueous media, including dimethyl sulfoxide (DMSO), a mixture of DMSO and an anionic surfactant such as sodium dodecyl sulfate, and a mixture of DMSO and an acidic surfactant such as dodecyl benzene sulfonic acid. The obtained copolymer, poly(acrylamide‐co‐N‐hexadecylacrylamide) [poly(Am‐co‐hAm)], was characterized by ¹H‐NMR. The physical properties of poly(Am‐co‐hAm)s synthesized in different media were compared with those of PAM and with each other by viscosity measurement, X‐ray diffraction, thermogravimetric analysis, and differential scanning calorimetry. We investigated the ways in which the polymerization medium affected the hydrophobic distribution within the resulting copolymer structure. This aspect, in turn, should have altered the solution properties and the microstructure of the copolymer. For this purpose, we studied the viscometric behavior in diluted solutions, the thermal behavior and thermal stability of the copolymers, and finally, the crystalline structure of the copolymers. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2014 , 131, 39939.     

Interpolymer interactions and miscibility in poly(n‐butyl methacrylate‐co‐methacrylic acid)/poly(styrene‐co‐N,N‐dimethyl acrylamide) blends

The miscibility of poly(n‐butyl methacrylate‐co‐methacrylic acid) containing 18 mol % methacrylic acid (BMAM‐18) and poly(styrene‐co‐N,N‐dimethyl acrylamide) containing 17 mol % N,N‐dimethyl acrylamide (SAD‐17) was investigated with viscometry, differential scanning calorimetry (DSC), and Fourier transform infrared (FTIR) spectroscopy. The DSC analysis showed a single glass‐transition temperature for all the blends, indicating that these copolymers were miscible over the entire composition range. The glass‐transition temperatures of these blends were higher than those calculated with the additivity rule. This was characteristic of the presence of specific interactions. The interactions between BMAM‐18 and the tertiary amide of SAD‐17 were studied with FTIR spectroscopy, which revealed that hydrogen‐bonding interactions occurred between the hydroxyl groups of BMAM‐18 and the carbonyl amide of SAD‐17. A new band characterizing these interactions appeared around 1613 cm^?1. The quantitative results showed that the fraction of the associated amide increased with an increase in the amount of the acidic BMAM‐18 copolymer. Although BMAM‐18 and SAD‐17 led to homogeneous solutions in butan‐2‐one, as the concentration of N,N‐dimethyl acrylamide increased to 32 mol % [as within the poly(styrene‐co‐N,N‐dimethyl acrylamide) containing 32 mol % N,N‐dimethyl acrylamide], complexation occurred when this latter compound was mixed with BMAM‐18 in butan‐2‐one. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2717–2724, 2006     

Thermomechanically stable dielectric composites based on poly(ether ketone) and BaTiO3 with improved electromagnetic shielding properties in X‐band

High‐performance barium titanate (BaTiO₃) filled poly(ether ketone) (PEK) composites were prepared by melt compounding with an aim to investigate the effect of BaTiO₃ on thermal, thermomechanical, dielectric, and electromagnetic interference shielding behavior of PEK. The content of BaTiO₃ in the PEK matrix was varied from 0 to 18 vol %. Scanning electron microscopy studies shows that BaTiO₃ particles were uniformly distributed in the PEK matrix up to 13 vol % loading followed by the formation of agglomerates at higher loading (18 vol %). Rockwell hardness increased up to 13 vol % loading followed by a decrease at 18 vol % loading. Dynamic mechanical analysis revealed that storage modulus increases with increase in BaTiO₃ loading with a maximum value of 3192 MPa at 13 vol % compared to 2099 MPa for neat PEK. Dielectric constant of composites measured in the frequency range of 8.2–12.4 GHz increased approximately three times upon incorporation of 18 vol % of BaTiO₃. This increment in dielectric constant is reflected in improved electromagnetic shielding properties as loading of dielectric filler (BaTiO₃) increases. Total shielding effectiveness of ?11 dB (～92% attenuation) at loading of 18 vol % BaTiO₃ justifies the use of these composites for suppression of EM radiations. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46413.     

The effect of fabrication methods on the mechanical and thermal properties of poly(lactide‐co‐glycolide) scaffolds

The purpose of this research was to evaluate the effects of the fabrication method, poly(ethylene glycol) (PEG) molecular weight, and PEG concentration on the mechanical and thermal properties of blended poly (lactide‐co‐glycolide) (PLGA)/PEG scaffolds. The manufacturing process was the dominant factor. The tested fabrication processes were compression, heat molding, and solvent casting/vacuum drying. The scaffolds produced by compression were strong and brittle with mechanical properties [compressive modulus (E) ～ 400 N/mm²] comparable to those of trabecular bone. The heat‐molded scaffolds were weaker and more ductile (E ～ 45 N/mm²) than the compressed scaffolds, so they were more applicable to non‐load‐bearing applications. The vacuum‐dried scaffolds completely lacked compressive strength (E ～ 5 N/mm²) and were considered unsuitable for scaffolding applications. The miscibilities of the blends were also affected by the processing method and were evaluated on the basis of the melting‐point depression of crystalline PEG. The miscibility of PLGA in PEG was greatest with vacuum drying (6–13%), followed by heat molding (0.4–1.5%) and then compression (0.2–0.8%). The application of heat and solvent to the blend successfully altered the miscibility of the two polymers. Overall, this study demonstrates the ability to fabricate scaffolds with distinct thermal and mechanical characteristics by the manipulation of the fabrication method. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 944–949, 2007     

Radiopaque,barium sulfate‐filled biomedical compounds of a poly(ether‐block‐amide) copolymer

Various radiopaque compounds of a poly (ether‐block‐amide) copolymer resin filled with fine barium sulfate particles were prepared by melt mixing. Material properties of the filled compounds were investigated using various material characterization techniques, including thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), dynamic rheometry, uniaxial tensile test, and dynamic mechanical thermal analysis (DMTA). The effects of the filler and its concentration on the measured material properties are evaluated. It has been found that in addition to its well‐known X‐ray radiopacity, the filler is quite effective in reinforcing some mechanical properties of the copolymer, including modulus of elasticity and yield strength. More interestingly, it has been observed that at low loading concentrations near 10 wt %, the filler may also act as a rigid, inorganic toughener for the copolymer by improving the postyield material extensibility of strain hardening against ultimate material fracture. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermal properties of low loss PTFE‐CeO2 dielectric ceramic composites for microwave substrate applications

Polytetrafluroethylene (PTFE) composites filled with CeO₂ were prepared by powder processing technique. The PTFE is used as the matrix and the loading fraction of CeO₂ in the composite varied up to 0.6 volume fraction. The thermal conductivity and coefficient of thermal expansion were studied in relation to filler concentration. The thermal conductivity increased and coefficient of thermal expansion decreased with increase in CeO₂ content. For 0.6 volume fraction loading of the ceramic, the composite has a thermal conductivity of 3.1 W/m°C and coefficient of thermal expansion 19.6 ppm/°C. Different theoretical approaches have been employed to predict the effective thermal conductivity and coefficient of thermal expansion of composite systems and the results were compared with the experimental data. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Correlation of chemical composition and microstructure with properties of poly(ɛ‐caprolactone‐co‐p‐dioxanone) random copolymers

With the aim to develop novel biodegradable materials with good flexibility and fast degradation rate, random copolymers of ?‐caprolactone (CL) and p‐dioxanone (PDO) with a full range of compositions were synthesized in bulk using stannous octoate as the ring‐opening catalyst. The chemical composition and number average sequence lengths of CL and PDO units determined by ¹H‐NMR were used to correlate with various properties of the copolymers. Although both CL and PDO are crystalline components, only one crystalline phase could be present for each copolymer. The low limit of average block length for the copolymers that could crystallize is 3.22 for L_CL and 3.43 for L_PDO, respectively. The crystallinity and crystalline morphology of the copolymers are dependent on the crystalline component as well as its number average sequence length. Irrespective of composition, all the copolymers have good solubility in chloroform with glass transition temperature much below room temperature, implying good flexibility of the materials. The incorporation of PDO component could significantly increase the water wettability of the copolymer surfaces and thereby accelerate the degradation rate of the materials. In conclusion, flexible biodegradable polymers with adjustable degradation and crystalline properties were acquired by random copolymerization of CL and PDO, which are expected to use in tissue engineering and drug delivery fields. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2978–2986, 2013     

Fabrication,characterization, and properties of poly(ethylene‐co‐vinyl acetate)/magnetite nanocomposites

Poly(ethylene‐co‐vinyl acetate) (EVA)/magnetite (Fe₃O₄) nanocomposite was prepared with different loading of Fe₃O₄ nanoparticles. The mixing and compounding were carried out on a two‐roll mixing mill and the sheets were prepared in a compression‐molding machine. The effect of loading of nanoparticles in EVA was investigated thoroughly by different characterization technique such as transmission electron microscopy (TEM), X‐ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), limiting oxygen index (LOI), and technological properties. TEM analysis showed the uniform dispersion of filler in the polymer matrix and the dispersion of filler decreased with increase in filler content. XRD of the nanocomposite revealed the more ordered structure of the polymer chain. An appreciable increase in glass transition temperature was observed owing to the restricted mobility of Fe₃O₄‐filled EVA nanocomposite. TGA and flame resistance studies indicated that the composites attain better thermal and flame resistance than EVA owing to the interaction of filler and polymer segments. Mechanical properties such as tensile strength, tear resistance, and modulus were increased for composites up to 7 phr of filler, which is presumably owing to aggregation of Fe₃O₄ nanoparticle at higher loading. The presence of Fe₃O₄ nanoparticles in the polymer matrix reduced the elongation at break and impact strength while improved hardness of the composite than unfilled EVA. The change in technological properties had been correlated with the variation of polymer–filler interaction estimated from the swelling behavior. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40116.     

Polyurethane/poly(ethylene‐co‐ethyl acrylate) and functional carbon black‐based hybrids: Physical properties and shape memory behavior

A polyurethane (PU) was developed from poly(dimethylamine‐co‐epichlorohydrin‐co‐ethylenediamine) (PDMAE) and polyethylene glycol (PEG) as soft segment and 2,4‐toluene diisocyanate (TDI) incorporating as hard segment. Later PU was blended with poly(ethylene‐co‐ethyl acrylate) (PEEA). Poly(vinyl alcohol)‐functionalized carbon black (CB‐PVA) nanoparticles was used as filler. The structure, morphology, mechanical, crystallization, and shape memory behavior (heat and voltage) were investigated methodically. Due to physical interaction of the blend components, unique self‐assembled network morphology was observed. The interpenetrating network was responsible for 83% rise in tensile modulus and 46% increase in Young's modulus of PU/PEEA/CB‐PVA 1 hybrid compared with neat PU/PEEA bend. Electrical conductivity was increased to 0.2 Scm^?1 with 1 wt % CB‐PVA nanofiller. The original shape of sample was almost 94% recovered using heat induced shape memory effect while 97% recovery was observed in an electric field of 40 V. Electroactive shape memory results were found better than heat stimulation effect. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43481.     

Crystallization kinetics of poly(1,4‐butylene‐co‐ethylene terephthalate)

The crystallization kinetics of poly(butylene terephthalate) (PBT), poly(ethylene terephthalate) (PET), and their copolymers poly(1,4‐butylene‐co‐ethylene terephthalate) (PBET) containing 70/30, 65/35 and 60/40 molar ratios of 1,4‐butanediol/ethylene glycol were investigated using differential scanning calorimetry (DSC) at crystallization temperatures (T_c) which were 35–90 °C below equilibrium melting temperature . Although these copolymers contain both monomers in high proportion, DSC data revealed for copolymer crystallization behaviour. The reason for such copolymers being able to crystallize could be due to the similar chemical structures of 1,4‐butanediol and ethylene glycol. DSC results for isothermal crystallization revealed that random copolymers had a lower degree of crystallinity and lower crystallite growth rate than those of homopolymers. DSC heating scans, after completion of isothermal crystallization, showed triple melting endotherms for all these polyesters, similar to those of other polymers as reported in the literature. The crystallization isotherms followed the Avrami equation with an exponent n of 2–2.5 for PET and 2.5–3.0 for PBT and PBETs. Analyses of the Lauritzen–Hoffman equation for DSC isothermal crystallization data revealed that PBT and PET had higher growth rate constant G_o, and nucleation constant K_g than those of PBET copolymers. © 2001 Society of Chemical Industry