Incorporation of 4‐aminobenzene functionalized multi‐walled carbon nanotubes in polyaniline for application in formic acid electrooxidation

Incorporation of carbon nanotubes (CNTs) in conducting polymer can lead to new composites with enhanced electrical and mechanical properties. However, the development of such composites has been hampered by the inability to disperse CNTs in polymer matrix due to the lack of chemical compatibility between polymers and CNTs. Covalent sidewall functionalization of carbon nanotube provides a feasible route to incorporate carbon nanotube in polymer. In this work, 4‐aminobenzene groups were grafted onto the surface of multi‐walled carbon nanotube (MWNT) via C? C covalent bond. Polyaniline (PANI)/MWNT composites were fabricated by electrochemical polymerization of aniline containing well‐dissolved functionalized MWNTs. The obtained composites can be used as catalyst supports for electrooxidation of formic acid. Cyclic voltammogram results show that platinum particles deposited in PANI/MWNT composite films exhibit higher electrocatalytic activity and better long‐term stability towards formic acid oxidation than that deposited in pure PANI films. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Fabrication of hybrid ladderlike polysilsesquioxane‐grafted multiwalled carbon nanotubes

Ladderlike polysilsesquioxanes (LPSs) containing chloromethylphenyl groups were synthesized from (p‐chloromethyl)phenyltrimethoxysilane under basic conditions. Functionalized multiwalled carbon nanotubes (MWNT–COOH) were prepared by the acid treatment of pristine multiwalled carbon nanotubes (MWNTs). MWNT–COOH was reacted with LPS to prepare LPS‐grafted MWNTs via ester linkages. The functionalization of MWNTs with LPS significantly altered the surface roughness of the MWNTs; there was a significant increase in the diameter of the MWNTs. The LPS‐grafted MWNTs had a 10–20 nm thickness along the outer walls according to the functionalization of the MWNTs with LPS. An advantage of the hybrid LPS‐grafted MWNTs was shown as improved thermal behavior. The composition, thermal properties, and surface morphology of the LPS‐grafted MWNTs were studied by Fourier transform infrared spectroscopy, thermogravimetric analysis, energy‐dispersive spectroscopy, scanning electron microscopy, atomic force microscopy, and transmission electron microscopy. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation and characterization of composites of polyaniline nanorods and multiwalled carbon nanotubes coated with polyaniline

Composites of polyaniline (PANI) nanorods and multiwalled carbon nanotubes (MWNTs) coated with PANI were prepared by in situ polymerization with perchloric acid as a dopant. Transmission electron microscopy images showed that the coexisting composites of PANI nanorods and MWNTs coated with PANI were formed at low MWNT contents. The interaction between MWNTs and PANI was proved by Fourier transform infrared and ultraviolet–visible spectra. The electrical conductivity of a dedoped PANI/MWNT composite with a 16.3 wt % concentration of MWNTs reached 3.0 × 10^?3 S/cm, which was 6 orders of magnitude higher than that of dedoped PANInanorods. The results also showed that coexisting composites of PANI nanorods and MWNTs coated with PANI had high electrochemical activity and good cyclic stability. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Fabrication of conducting polyaniline–multiwalled carbon nanotube nanocomposites and their use as templates for loading gold nanoparticles

A new and effective route to synthesize conducting polyaniline‐multiwalled carbon nanotube (PANI ‐f‐MWNT) nanocomposites (where ‘f’ denotes that the MWNTs have been functionalized) starting with amine‐protected 4‐aminophenol is reported. Aminophenol‐functionalized MWNTs were initially synthesized by functionalizing acyl chloride‐terminated nanotubes with N‐(tert‐butoxycarbonyl)‐4‐aminophenol followed by the in situ chemical oxidative grafting of aniline in the presence of ammonium persulfate as an oxidizing agent. Control of the morphology and thickness of the polymer–MWNT nanocomposites was achieved by varying the weight ratios of aniline monomers and MWNTs in the polymerization process. Fourier transform infrared spectroscopy was employed to characterize the initial changes in surface functionalities which also confirmed that PANI was covalently grafted to the MWNTs. Electron microscopy and UV‐visible absorption spectroscopy were employed to characterize the morphology and chemical structure of the resulting hybrids. The results obtained indicate that the structure of the MWNTs was not perturbed by the incorporation of PANI. The content of the polymer in the nanocomposites was determined thermogravimetrically, while the electrical conductivity was obtained using four‐probe measurements. The PANI ‐f‐MWNT nanocomposites were adopted as templates for further decoration with gold nanoparticles in solution, thus opening new possibilities for their prospective technological applications. Copyright © 2010 Society of Chemical Industry     

Synthesis and characterization of novel hybrid polyoxazoline‐grafted multiwalled carbon nanotubes

The novel hybrid polyoxazoline‐grafted multiwalled carbon nanotubes (POZO‐grafted MWNTs) were synthesized by the reaction of partially hydrolyzed polyoxazolines (Hydrolyzed‐POZO) and MWNTs having carboxylic acid groups (MWNT‐COOH) in the presence of DCC as a condensing agent. Hydrolyzed‐POZO (degree of hydrolysis, 20.2 mol % by ¹H‐NMR) were produced from the hydrolysis of polyoxazolines in an aqueous NaOH solution at reflux for 72 h. MWNT‐COOH were prepared by acid treatment of pristine MWNTs. The composition, structure, thermal property, and surface morphology of the novel hybrid POZO‐grafted MWNTs were fully characterized by FT‐IR, Raman, ¹H‐NMR, DSC, TGA, SEM, and TEM. The obtained POZO‐grafted MWNTs are well soluble in various organic solvents and water. It was observed that the glass transition temperature (T_g) of POZO‐grafted MWNTs was lower than that of Hydrolyzed‐POZO due to the absence of hydrogen bonding interactions between Hydrolyzed‐POZO itself caused by the incorporation with MWNTs. It was also found that Hydrolyzed‐POZO was homogeneously attached to the surfaces of MWNTs through the “grafting‐to” method. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Doped polyaniline/multiwalled carbon nanotube composites: Preparation and characterization

Polyaniline (PANI)/multiwalled carbon nanotube (MWNT) composites with a uniform tubular structure were prepared from in situ polymerization by dissolving amino‐functionalized MWNT (a‐MWNT) in aniline monomer. For this the oxidized multiwalled nanotube was functionalized with ethylenediamine, which provided ethylenediamine functional group on the MWNT surface confirmed by Fourier‐transform infrared spectra (FT‐IR). The a‐MWNT was dissolved in aniline monomer, and the in situ polymerization of aniline in the presence of these well dispersed nanotubes yielded a novel tubular composite of carbon nanotube having an ordered uniform encapsulation of doped polyaniline. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) showed that the nanotubes were coated with a PANI layer. The thermal stability and electrical conductivity of the PANI /MWNTs composites were characterized by thermogravimetric analysis (TGA) and conventional four‐probe method respectively. Compared with pure PANI, the electrical conductivity and the decomposition temperature of the MWNTs/PANI composites increased with the enhancement of MWNT content in PANI matrix. POLYM. COMPOS., 34:1119–1125, 2013. © 2013 Society of Plastics Engineers     

Preparation and properties of multiwalled carbon nanotube/polycaprolactone nanocomposites

Multiwalled carbon nanotube/polycaprolactone nanocomposites (MWNT/PCL) were prepared by in situ polymerization, whereby as‐received MWNTs (P‐MWNTs) and purified MWNTs (A‐MWNTs) were used as reinforcing materials. The A‐MWNTs were purified by nitric acid treatment, which introduced the carboxyl groups (COOH) on the MWNT. The micrographs of the fractured surfaces of the nanocomposites showed that the A‐MWNTs in A‐MWNT/PCL were better dispersed than P‐MWNTs in PCL matrix (P‐MWNT/PCL). Percolation thresholds of the P‐MWNT/PCL and A‐MWNT/PCL, which were studied by rheological properties, were found at ～2 wt % of the MWNT. The conductivity of the P‐MWNT/PCL was between 10^?1 and 10^?2 S/cm by loading of 2 wt % of MWNT although that of the A‐MWNT/PCL reached ～10^?2 S/cm by loading of 7 wt % of MWNT. The conductivity of the P‐MWNT/PCL was higher than that of the A‐MWNT/PCL at the entire range of the studied MWNT loading, which might be due to the destruction of π‐network of the MWNT by acid treatment, although the A‐MWNT/PCL was better dispersed than the P‐MWNT/PCL. The amount of the MWNT at which the conductivity of the nanocomposite started to increase was strongly correlated with the percolation threshold. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1957–1963, 2007     

Characterizing composite of multiwalled carbon nanotubes and POE‐g‐AA prepared via melting method

Multiwalled carbon nanotubes (MWNTs) with acyl chloride functional groups and a metallocene polyethylene–octene elastomer (POE) or an acrylic acid‐grafted metallocene polyethylene–octene elastomer (POE‐g‐AA) were used to prepare hybrids (POE/MWNTs or POE‐g‐AA/MWNTs) using a melting method, with a view to identify a hybrid with improved thermal properties. Hybrids were characterized using Fourier transform infrared spectroscopy, ¹³C solid‐state nuclear magnetic resonance, X‐ray diffraction, thermogravimetry analysis, and scanning electron microscopy. MWNTs were purified using acid treatment, and results showed that ? COOH of MWNTs increased with acid treatment time and leveled off after 24‐h treatment. Much better dispersion and homogeneity of MWNTs was obtained with POE‐g‐AA in place of POE as the matrix. As a result, tensile strength at break of POE‐g‐AA/MWNTs was significantly improved even at 5 wt % MWNT content. Moreover, temperature of thermal decomposition for POE‐g‐AA/MWNTs was about 40–50°C higher than that for POE‐g‐AA, indicating higher thermal stability. This was because the carboxylic acid groups in POE‐g‐AA and the acyl chloride functional sites in MWNTs allow the formation of stronger chemical bonds. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1328–1337, 2007     

Influence of multi-walled carbon nanotubes on the electrochemical performance of graphene nanocomposites for supercapacitor electrodes

In this work, multi-walled carbon nanotube (MWNT) bonded graphene (M-GR) composites were prepared using the chemical reduction of graphite oxide (GO) and acid treated MWNTs with different ratios. The M-GR/polyaniline (PANI) nanocomposites (M-GR/PANI) were prepared using oxidation polymerization. The effect of the M-GR ratio on the electrochemical performances of the M-GR/PANI was investigated. It was found that the substrate 2D graphene was coated with 1D MWNTs by chemical reduction and the M-GR was further coated with PANI, leading to increased electrical properties by the π–π interaction between the M-GR and PANI. In addition, the electrochemical performances, such as the current density, charge–discharge, and specific capacitance of the M-GR/PANI were higher than those of graphene/PANI and the highest specific capacitance (1118 F/g) of the composites was obtained at a scan rate of 0.1 A/g for the PANI containing a 0.5 M-GR ratio compared to 191 F/g for the graphene/PANI. The dispersion of the MWNTs onto the graphene surface and the ratio of M-GR had a pronounced effect on the electrochemical performance of the PANI-based composites, which was attributed to the highly conductive pathway created by the M-GR incorporated in the PANI-based composites and the synergistic effect between M-GR and PANI.     

Dulse‐derived porous carbon–polyaniline nanocomposite electrode for high‐performance supercapacitors

Dulse‐derived porous carbon (DDPC)–polyaniline (PANI) nanocomposites were fabricated by a method based on the in situ chemical oxidation polymerization of aniline on DDPC. The characterization of the material showed that the nano‐PANI was grown on the surface of DDPC in the form of nanosticks or nanoparticles. The DDPC–PANI nanocomposites were further used as electrode materials for energy‐storage applications. Meanwhile, the effect of the amount of aniline on the electrochemical performance of DDPC–PANI was also investigated. The results show that a maximum specific capacitance of 458 F/g was achieved for the DDPC–PANI nanocomposites; this was higher than that of the DDPC electrode (218 F/g), and the PANI electrode (318 F/g). The specific capacitance of DDPC–PANI remained 66.0% of the initial value after 5000 cycles; this was higher than that of PANI (50.5%). Finally, a device of DDPC–PANI–activated carbon (AC) was assembled with DDPC–PANI as a positive electrode, which exhibited a high energy density of 9.02 W h/kg, which was higher than that of PANI–AC device. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45776.     

Preparation and characterization of polydiphenylamine/multi‐walled carbon nanotube composites

We describe the synthesis of methane sulfonic acid (MeSA)‐doped poly(diphenylamine) (PDPA) with carboxylic groups containing multi‐walled carbon nanotubes (c‐MWNTs) via in situ polymerization. Diphenylamine monomers were adsorbed on to the surface of c‐MWNTs and polymerized to form PDPA/c‐MWNT composites. SEM and TEM images indicated two different types of materials: the thinner fibrous phase and the larger globular phase. The individual fibrous phase had a diameter around 100–130 nm, which should be the carbon nanotubes (diameter 20–30 nm) coated with a PDPA layer. The structure of PDPA/c‐MWNT composites was characterized by FTIR, UV‐visible spectroscopy and X‐ray diffraction patterns. The electrical conductivities of PDPA/c‐MWNT composites were much higher than that of PDPA without c‐MWNTs. Copyright © 2006 Society of Chemical Industry     

Free‐standing aniline oligomer functionalized multiwalled carbon nanotube films from a filtration method

High electrochemical active free‐standing multiwalled carbon nanotube (MWNT) films have been synthesized from aniline oligomer functionalized MWNTs (MWNT‐AO), by using filtration of the acidic phosphate ester (APE) doped MWNT‐AO dispersions. The homogeneously distributed MWNTs endowed APE/MWNT films automatically releasing from the filter membrane. The sheet resistivity of MWNT‐AO (850 Ω sq^?1) showed a lower value than that of carboxyl MWNTs (1273 Ω sq^?1), due to the doping effect of MWNT on aniline oligomer, confirmed by the N1s X‐ray photoelectron spectrum. However, it showed a higher sheet resistivity value of 1526 Ω sq^?1 after further doped by APE, because of the presence of unreacted dopant. After removing the residual insulating dopant by the vacuum filtration, the resultant APE/MWNT films showed the sheet resistivity value as low as 131 Ω sq^?1. Thermogravimetric analysis showed that the MWNT loading in the film can be over than 77%, which showed the specific capacitance as high as 249 F g^?1. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40259.     

Poly (N‐methylaniline)/multi‐walled carbon nanotube composites—Synthesis,characterization, and electrical properties

This study described the synthesis of hydrochloric acid (HCl)‐doped poly (N‐methylaniline) (PNMA) with carboxylic groups containing multi‐walled carbon nanotubes (c‐MWNTs) via in situ polymerization. Based on the π–π electron interaction between c‐MWNTs and the N‐methylaniline monomer and the hydrogen bond interaction between the carboxyl groups of c‐MWNTs and imine groups of N‐methylaniline monomers, N‐methylaniline molecules were adsorbed on the surface of c‐MWNTs and polymerized to form PNMA/c‐MWNT composites. Scanning electron microscopy images showed that both the thinner fibrous phase and the larger block phase could be observed. The individual fibrous phases had diameters from several tens to hundreds of nanometers, depending on the PNMA content. Transmission electron microscopy proved that PNMA/c‐MWNTs composite fibrous phases were core (c‐MWNT)‐shell (PNMA) tubular structures. The structure of PNMA/c‐MWNT composites was characterized by FTIR, UV–vis spectra, and X‐ray diffraction patterns. The electrical conductivities of PNMA/c‐MWNT composites were much higher than that of PNMA without c‐MWNTs. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2356–2361, 2006     

Synthesis and characterization of polyimide/multi‐walled carbon nanotube nanocomposites

Polyimide/multi‐walled carbon nanotube (PI‐MWNT) nanocomposites were fabricated by an in situ polymerization process. Chemical compatibility between the PI matrix and MWNTs is achieved by pretreatment of the carbon nanotubes in a mixture of sulfuric acid and nitric acid. The dispersion of MWNTs in the PI matrix was found to be enhanced significantly after acid modification. The glass transition (T_g) and decomposition (T_d) temperature of PI‐MWNT nanocomposites were improved as the MWNT content increased from 0.5 to 15 wt%. The storage modulus of the PI/MWNT nanocomposites is nine times higher than that of pristine PI at room temperature. The tensile strength of PI doubles when 7 wt% MWNTs is added. The dielectric constant of the PI‐MWNT nanocomposites increased from 3.5 to 80 (1 kHz) as the MWNT content increased to 15 wt%. The present study demonstrates that enhanced mechanical properties can be obtained through a simple in‐situ polymerization process. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Styrene‐butadiene‐styrene copolymer compatibilized interfacial modified multiwalled carbon nanotubes with mechanical and piezoresistive properties

In this study, styrene‐butadiene‐styrene tri‐block copolymer/multiwalled carbon nanotubes (SBS/MWNTs) were prepared by means of a solution blending method. To enhance the compatibility between SBS and MWNTs, the SBS grafted MWNTs (SBS‐g‐MWNTs) were used to replace MWNTs. The MWNTs were chemically hydroxylated by the dissolved KOH solution with ethanol as solvent and then reacted with 3‐Aminopropyltriethoxysilane (APTES) to functionalize them with amino groups (MWNT‐NH₂). The SBS‐g‐MWNTs were finally obtained by the reaction of MWNT‐NH₂ and maleic anhydride grafted SBS (MAH‐g‐SBS). The SBS‐g‐MWNTs were characterized by X‐ray photoelectron spectroscopy (XPS), Fourier transform‐infrared spectroscopy (FT‐IR), transmission electron microscopy (TEM), scanning electron microscope (SEM), and thermogravimetric analysis (TGA). The results showed that the SBS molecules were homogeneously bonded onto the surface of the MWNTs, leading to an improvement of the mechanical and electrical properties of SBS/SBS‐g‐MWNTs composites due to the excellent interfacial adhesion and dispersion of SBS‐g‐MWNTs in SBS. A series of continuous tests were carried out to explore the electrical‐mechanical properties of the SBS/SBS‐g‐MWNTs composites. We found out that, near the percolation threshold, the well‐dispersed SBS/SBS‐g‐MWNTs composites showed good piezoresistive characteristics and small mechanical destructions for the development of little deformation under vertical pressure. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42945.     

In situ doping of PANI nanocomposites by gold nanoparticles for high‐performance electrochemical energy storage

Polyaniline (PANI) in situ doped with gold nanoparticles (Au/PANI) is synthesized by oxidative polymerization as electrode material for supercapacitor. The morphologies and structure of the obtained products are characterized by transmission electron microscopy, scanning electron microscopy, and Fourier transform infrared spectroscopy; and electrochemical behaviors were measured by electrochemical workstation. The results show that the nanocomposites of Au/PANI are fabricated with gold nanoparticles (nano‐Au) dispersed well in PANI bulk; and specific capacitance (SC) and rate ability of Au/PANI are improved compared to the pristine PANI due to the introduction of nano‐Au. With nano‐Au content increasing, SC first increase and then decrease and the maximum SC of Au/PANI nanocomposite is up to 462 F g^?1 with the nano‐Au content of 1.64 wt %. Finally, both asymmetric and symmetric supercapacitor devices are assembled, exhibiting high energy densities of 8.95 and 4.17 Wh kg^?1, respectively. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45309.     

Thermomechanical and water‐responsive shape memory properties of carbon nanotubes‐reinforced hyperbranched polyurethane composites

Shape memory composites of hyperbranched polyurethane (HBPU) and acid‐treated multi‐walled carbon nanotubes (MWNTs) were prepared using an in situ polymerization method. HBPUs with different hard segments contents were synthesized via the A₂ + B₃ approach using poly(ethylene glycol) (PEG) as a soft segment, 4,4′‐methylene bis(phenylisocynate), castor oil, and 1,4‐butanediol as hard segment. Compared to HBPU, the HBPU/MWNT composites showed faster shape recovery and double the shape recovery stress in the thermomechanical shape memory test, which was dependent on the MWNTs content and HBPU hard segment content. The water‐responsive shape memory effect of HBPU/MWNT composites was considered to result from the combined contribution of hydrophilic PEG and well dispersed MWNTs in highly branched HBPU molecules. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Electrochemical behaviors of polyaniline–poly(styrene‐sulfonic acid) complexes and related films

This research focuses on the syntheses of polyaniline with poly(styrenesulfonic acid) and their electrochemical behavior, including absorbance behavior and electrochemical response time of polyaniline‐poly(styrenesulfonic acid) [PANI–PSSA]. The complexes PANI–PSSA were prepared by electrochemical polymerization of monomer (aniline) with PSSA, using indium‐tin oxide (ITO) as working electrode in 1M HCl solution. Polyaniline (PANI), poly(o‐phenetidine)–poly(styrenesulfonic acid) [POP–PSSA], and poly(2‐ethylaniline)–poly(styrenesulfonic acid) [P2E‐PSSA] also were prepared by electrochemical polymerization and to be the reference samples. The products were characterized by IR, VIS, EPR, water solubility, elemental analysis, conductivity, SEM, and TEM. IR spectral studies shows that the structure of PANI–PSSA complexes is similar to that of polyaniline. EPR and visible spectra indicate the formation of polarons. The morphology of the blend were investigated by SEM and TEM, which indicate the conducting component and electrically conductive property of the polymer complexes. Elemental analysis results show that PANI–PSSA has a nitrogen to sulfur ratio (N/S) of 38%, lower than that for POP–PSSA (52%) and P2E–PSSA (41%). Conductivity of the complexes are around 10^?2 S/cm, solubility of PANI–PSSA in water is 3.1 g/L. The UV‐Vis. absorbance spectra of the hybrid organic/inorganic complementary electro‐chromic device (ECD), comprising a polyaniline–poly(styrenesulfonic acid) [PANI–PSSA] complexes and tungsten oxide (WO₃) thin film coupled in combination with a polymer electrolyte poly(2‐acrylamido‐2‐methyl‐propane‐sulfonic acid) [PAMPSA]. PANI–PSSA microstructure surface images have been studied by AFM. By applying a potential of ～3.0 V across the two external ITO contacts, we are able to modulate the light absorption also in the UV‐Vis region (200–900 nm) wavelength region. For example, the absorption changes from 1.20 to 0.6 at 720 nm. The complexes PANI–PSSA, POP–PSSA, and P2E–PSSA were prepared by electrochemical polymerization of monomer (aniline, o‐phenetidine, or 2‐ethylaniline) with poly(styrenesulfonic acid), using ITO as working electrode in 1M HCl solution, respectively. UV‐Vis spectra measurements shows the evidences for the dopped polyaniline system to be a highly electrochemical response time, recorded at the temperature 298 K, and the results were further analyzed on the basis of the color‐ discolor model, which is a typical of protontation systems. Under the reaction time (3 s) and monomer (aniline, o‐phenetidine, 2‐ethylaniline) concentration (0.6M) with PSSA (0.15M), the best electrochemical color and discolor time of the PANI–PSSA is slower than POP–PSSA complexes (125/125 ms; thickness, 3.00 μm) and P2E–PSSA complexes. Under the same thickness (10 μm), the best electrochemical color and discolor time of the PANI–PSSA complexes is 1500/750 ms, that is much slower than P2E–PSSA complexes (750/500 ms) and POP–PSSA complexes (500/250 ms). In film growing rate, the PANI–PSSA complexes (0.54 μm/s) are slower than P2E–PSSA complexes (0.79 μm/s) and POP–PSSA complexes (1.00 μm/s), it can be attributed to the substituted polyaniline that presence of electro‐donating (? OC₂H₅ or ? C₂H₅₎ group present in aniline monomer. The EPR spectra of the samples were recorded both at 298 K and 77 K, and were further analyzed on the basis of the polaron–bipolaron model. The narrower line‐width of the substituted polyaniline complexes arises due to polarons; i.e., it is proposed that charge transport take place through both polarons and bipolarons, compared to their salts can be attributed to the lower degree of structural disorder, the oxygen absorption on the polymeric molecular complexes, and due to presence of electro‐donating (? OC₂H₅ or ? C₂H₅) group present in aniline monomer. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100:4023–4044, 2006     

Effects of surface modification with 3‐aminopropyltriethoxysilane on structure and mechanical property of multiwalled carbon nanotube/polycarbonate composites

Hydroxyl functionalized multiwalled carbon nanotubes (H‐MWNTs) were silanized using 3‐aminopropyltriethoxysilane (APTES) in order to improve the dispersion and interfacial interaction in composites. MWNT/polycarbonate (PC) composites filled with H‐MWNTs and silanized MWNTs (S‐MWNTs) were fabricated by melt mixing and injection molding. Fourier transform infrared spectrometry (FTIR) and energy dispersion X‐ray spectroscopy (EDS) were employed to prove the presence of APTES on the surface of S‐MWNTs. In addition, thermogravimetric analysis (TGA) was used to evaluate the relative amount of introduced APTES. The microstructure and mechanical property of both composites were investigated by scanning electron microscopy (SEM), transmission electron microscope (TEM), tensile test and dynamic mechanical analysis (DMA). The SEM and TEM images showed that S‐MWNT/PC composites had better dispersion and interfacial adhesion than H‐MWNT/PC composites. A reinforcing and toughening effect on tensile behavior of composites was obtained after silane functionalization. The storage modulus of composites increased markedly as a function of MWNTs content, especially for the composites with S‐MWNTs. In summary, the silanization can improve the dispersion of MWNTs and the interfacial adhesion between MWNTs and PC so as to enhance the mechanical properties of composites. POLYM. COMPOS., 37:1914–1923, 2016. © 2015 Society of Plastics Engineers     

Functionalized polyacrylonitrile‐nanofiber based immunosensor for Vibrio cholerae detection

Polyacrylonitrile nanofibers (PANnf's) were electrospun directly onto an indium tin oxide (ITO)‐coated glass substrate. The PANnf/ITO electrode was partially hydrolyzed with an NaOH aqueous solution at ambient temperature to convert the nitrile groups of the PANnf's into carboxyl groups was confirmed by Fourier transform infrared spectroscopy. Furthermore, 1‐ethyl‐3‐(3‐dimethylaminopropyl) carbodiimide–N‐hydroxy succinimide chemistry was used to activate the ? COOH groups of PANnf's for the covalent co‐immobilization of monoclonal antibodies against Vibrio cholerae and bovine serum albumin for V. cholerae toxin detection. Structural, functional, and electrochemical studies of the PANnf/ITO electrode and BSA/Ab/PANnf/ITO immunoelectrode were performed, and found a uniform distribution of nanofibers with diameter of 325 ± 7.7% nm. The electrochemical response studies showed an improved sensing performance of the immunoelectrode with a detection of 6.25–500 ng/mL, a low limit of detection of 0.22 ng/mL, a sensitivity of 90 nA ng^?1 mL cm^?2, an association constant of 45.2 ng/mL, and a dissociation constant of 8 ng/mL. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44170.