Synthesis and characterization of ABA‐type triblock copolymers derived from polyimide and poly(2‐methyl‐2‐adamantyl methacrylate)

ABA‐type triblock copolymers derived from 4,4‐(hexafluoroisopropylidene)diphthalic anhydride‐2,3,5,6‐tetramethyl‐1,4‐phenylenediamine and 2‐methyl‐2‐adamantyl methacrylate (2‐MAdMA) were synthesized via atom transfer radical polymerization. The component ratios of polyimide (PI) and poly(2‐MAdMA) (PMAdMA) were about 8/2, 6/4 and 3/7, as determined using ¹H NMR spectroscopy and thermogravimetric analysis (TGA). The film structure of the triblock copolymers was dependent on the PI structure. Hydrophobicity increased as the component ratio of PMAdMA increased. Based on TGA, three‐step decomposition behaviors of all triblock copolymers derived from PI and PMAdMA in nitrogen and air atmosphere were observed. The gas permeability of the triblock copolymers was lower than that of PI. This finding can be attributed to the decrease in fractional free volume by the adamantane component and the decrease in permeability of the triblock copolymers compared with PI. The dielectric constant of the triblock copolymers was lower than that of PI. The dielectric constant was dependent on molar volume and molar porlarizability, and the dielectric constant derived from the symmetric structure of adamantane was reduced. The ABA‐type triblock copolymers derived from PI and PMAdMA can be considered as new polymer materials with high hydrophobicity, high H₂/CO₂ selectivity and low dielectric constant. © 2013 Society of Chemical Industry     

Effects of thermal treatment on the CO2 sorption of triblockcopolymers derived from polyimide and poly(methylmethacrylate)

ABA‐type triblock copolymers were synthesized using 4,4‐(hexafluoroisopropylidene) diphthalic anhydride‐2,3,5,6‐tetramethyl‐1,4‐phenylenediamine (6FDA‐TeMPD) and poly(methyl methacrylate) (PMMA). The films were characterized by determining the effects of different content ratios and thermal decomposition of PMMA block on CO₂ sorption properties. TGA results showed that a thermal labile block can be completely decomposed under a previously reported thermal condition. SEM results presented that the asperity was micro‐phase separation caused by the PMMA block content rate. Numerous pores with sizes of approximately 10 to 50 nm were detected on Block(28/72) and Block(10/90). The isotherms of all films fitted the dual‐mode sorption model, and CO₂ sorption decreased with increased PMMA content rate. Infinite‐dilution CO₂ solubility depended on the Langmuir's site of each polymer because S_H0/S₀ of PI and Block(PI/PMMA) varied from 0.84 to 0.92 CO₂ affinity was increased by thermal treatment as indicated by the higher b and S₀ values of thermally treated films than those of nontreated films. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42208.     

Characterization and water vapor sorption property of ABA‐type triblock copolymers derived from polyimide and poly(methyl methacrylate)

The characterization of ABA‐type triblock copolymer films derived from polyimide (PI) macroinitiator and poly(methyl methacrylate) (PMMA) synthesized by atom transfer radical polymerization was investigated by focusing on different block lengths of PMMA. The hydrophobic property tends to increase with increasing PMMA content in the triblock copolymers, while the PMMA blocks enhance the charge transfer interaction between the PI segments. The water vapor sorption measurement of triblock copolymers was determined at 35 °C. The water vapor solubility of triblock copolymers tends to decrease with increasing PMMA content. In addition, linear correlations were observed between the solubility and polymer‐free volume and polymer molecular polarity in triblock copolymers as well as in other conventional polymer families. According to Zimm?Lundberg analysis, the PMMA block segments in the triblock copolymers accelerate water vapor clustering due to the high mobility of PMMA. The mobility of PMMA block segments strongly affected not only physical properties but also the water vapor solubility of the triblock copolymers. The ABA triblock copolymerization composed of PI and PMMA is one of the effective ways to improve the hydrophobic property. © 2013 Society of Chemical Industry     

Preparation of porous membranes by selective decomposition of adamantane unit in ABA‐type triblock copolymer

The mechanism of pore formation by selective decomposition of adamantane unit in an ABA‐type triblock copolymer derived from 4,4‐(hexafluoroisopropylidene)diphthalic anhydride‐2,3,5,6‐tetramethyl‐1,4‐phenylenediamine (6FDA‐TeMPD) and poly(2‐methyl‐2‐adamantylmethacrylate) (PMAdMA) was investigated on this basis. This study aims to developing a novel method of material design for high‐precision gas separation membranes and application to electric devices by improving dielectric constant. Scanning electron microscopy images showed that the membrane structure changed considerably after heating; the difference increased with the increase in adamantane content. Interestingly, the internal structure of Block(36 mol%6FDA‐TeMPD/64 mol%PMAdMA) membrane was almost unchanged although its surface structure was changed. These results suggest that the mechanism of formation of porous membrane involves the decomposition of adamantane unit from surface. In addition, more adamantane units inside the membrane were discharged to the surface of the membrane through a path formed by decomposed adamantane units. POLYM. ENG. SCI., 56:1191–1200, 2016. © 2016 Society of Plastics Engineers     

Preparation of Nanowells on a PS‐b‐PMMA Copolymer Thin Film by CO2 Treatment

Ordered nanowells with diameters of ca. 40 nm and depth of 1–2 nm were prepared on a poly(methyl methacrylate) (PMMA) spherical domain, which was exposed on the polystyrene‐block‐poly(methyl methacrylate) (PS‐b‐PMMA) copolymer thin film. The PS‐b‐PMMA film formed spherical PMMA domains after the film was annealed above the order–disorder transition temperature. CO₂ was dissolved into the PS‐b‐PMMA thin film at 8.6 MPa and at a temperature of 20 °C. The release of CO₂‐pressure at the same temperature created the nanowell on the PMMA domain. The temperature and pressure to create nanowells in the PMMA domain affected the possibility of nanowell's formation.

     

Synthesis of amphiphilic poly(methyl methacrylate)‐block‐poly(methacrylic acid) diblock copolymers by atom transfer radical polymerization

Atom transfer radical polymerization (ATRP) of 1‐(butoxy)ethyl methacrylate (BEMA) was carried out using CuBr/2,2′‐bipyridyl complex as catalyst and 2‐bromo‐2‐methyl‐propionic acid ester as initiator. The number average molecular weight of the obtained polymers increased with monomer conversion, and molecular weight distributions were unimodal throughout the reaction and shifted toward higher molecular weights. Using poly(methyl methacrylate) (PMMA) with a bromine atom at the chain end, which was prepared by ATRP, as the macro‐initiator, a diblock copolymer PMMA‐block‐poly [1‐(butoxy)ethyl methacrylate] (PMMA‐b‐PBEMA) has been synthesized by means of ATRP of BEMA. The amphiphilic diblock copolymer PMMA‐block‐poly(methacrylic acid) can be further obtained very easily by hydrolysis of PMMA‐b‐PBEMA under mild acidic conditions. The molecular weight and the structure of the above‐mentioned polymers were characterized with gel permeation chromatography, infrared spectroscopy and nuclear magnetic resonance. Copyright © 2005 Society of Chemical Industry     

Nanophase morphology and crystallization in poly(vinylidene fluoride)/polydimethylsiloxane‐block‐poly(methyl methacrylate)‐block‐polystyrene blends

An approach to achieve confined crystallization of ferroelectric semicrystalline poly(vinylidene fluoride) (PVDF) was investigated. A novel polydimethylsiloxane‐block‐poly(methyl methacrylate)‐block‐polystyrene (PDMS‐b‐PMMA‐b‐PS) triblock copolymer was synthesized by the atom‐transfer radical polymerization method and blended with PVDF. Miscibility, crystallization and morphology of the PVDF/PDMS‐b‐PMMA‐b‐PS blends were studied within the whole range of concentration. In this A‐b‐B‐b‐C/D type of triblock copolymer/homopolymer system, crystallizable PVDF (D) and PMMA (B) middle block are miscible because of specific intermolecular interactions while A block (PDMS) and C block (PS) are immiscible with PVDF. Nanostructured morphology is formed via self‐assembly, displaying a variety of phase structures and semicrystalline morphologies. Crystallization at 145 °C reveals that both α and β crystalline phases of PVDF are present in PVDF/PDMS‐b‐PMMA‐b‐PS blends. Incorporation of the triblock copolymer decreases the degree of crystallization and enhances the proportion of β to α phase of semicrystalline PVDF. Introduction of PDMS‐b‐PMMA‐b‐PS triblock copolymer to PVDF makes the crystalline structures compact and confines the crystal size. Moreover, small‐angle X‐ray scattering results indicate that the immiscible PDMS as a soft block and PS as a hard block are localized in PVDF crystalline structures. © 2019 Society of Chemical Industry     

Nanostructured thermosetting epoxy systems modified with poly(isoprene‐b‐methyl metacrylate) diblock copolymer and polyisoprene‐grafted carbon nanotubes

Nanostructured thermosetting composites based on an epoxy matrix modified with poly(isoprene‐b‐methyl methacrylate) (PI‐b‐PMMA) block copolymer were prepared through PI block segregation. Morphological structures were examined by means of atomic microscopy force microscopy. As epoxy/pristine multi‐walled carbon nanotubes (MWCNT) systems were found to present big agglomerations, with a very poor dispersion of the nanofiller, epoxy/PI‐b‐PMMA/MWCNT systems were prepared by using polyisoprene‐grafted carbon nanotubes (PI‐g‐CNT) to enhance compatibility with the matrix and improve dispersion. It was found that the functionalization of MWCNT with grafted polyisoprene was not enough to totally disperse them into the epoxy matrix but an improvement of the dispersion of carbon nanotubes was achieved by nanostructuring epoxy matrix with PI‐b‐PMMA when compared with epoxy/MWCNT composites without nanostructuring. Nevertheless, some agglomerates were still present and the complete dispersion or confinement of nanotubes into desired domains was not achieved. Thermomechanical properties slightly increase with PI‐g‐CNT content for nanostructured samples, whereas for nonnanostructured epoxy/PI‐g‐CNT composites they appeared almost constant and even decreased for the highest nanofiller amount due to the presence of agglomerates. Compression properties slightly decreased with block copolymer content, while remained almost constant with nanofiller amount. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Organosoluble and light‐colored fluorinated polyimides based on 1,1‐bis[4‐(4‐amino‐2‐trifluoromethylphenoxy)phenyl]‐1‐phenylethane and various aromatic dianhydrides

To investigate the CF₃ group affecting the coloration and solubility of polyimides (PI), a novel fluorinated diamine 1,1‐bis[4‐(4‐amino‐2‐ trifluoromethylphenoxy)phenyl]‐1‐phenylethane (2) was prepared from 1,1‐ bis(4‐hydrophenyl)‐1‐phenylethan and 2‐chloro‐5‐nitrobenzotrifluoride. A series of light‐colored and soluble PI 5 were synthesized from 2 and various aromatic dianhydrides 3a–f using a standard two‐stage process with thermal 5a– f(H) and chemical 5a–f(C) imidization of poly(amic acid). The 5 series had inherent viscosities ranging from 0.55 to 0.98 dL/g. Most of 5a–f(H) were soluble in amide‐type solvents, such as N‐methyl‐2‐pyrrolidone (NMP), N,N‐ dimethylacetamide (DMAc), and N,N‐dimethylformamide (DMF), and even soluble in less polar solvents, such as m‐Cresol, Py, Dioxane, THF, and CH₂Cl₂, and the 5(C) series was soluble in all solvents. The GPC data of the 5a–f(C) indicated that the Mn and Mw values were in the range of 5.5–8.7 × 10⁴ and 8.5–10.6 × 10⁴, respectively, and the polydispersity index (PDI) Mw /Mn values were 1.2–1.5. The PI 5 series had excellent mechanical properties. The glass transition temperatures of the 5 series were in the range of 232–276°C, and the 10% weight loss temperatures were at 505–548 °C in nitrogen and 508–532 °C in air, respectively. They left more than 56% char yield at 800°C in nitrogen. These films had cutoff wavelengths between 356.5–411.5 nm, the b* values ranged from 5.0–71.1, the dielectric constants, were 3.11–3.43 (1MHz) and the moisture absorptions were in the range of 011–0.40%. Comparing 5 containing the analogous PI 6 series based on 1,1‐bis[4‐(4‐aminophenoxy)phenyl]‐1‐ phenylethane (BAPPE), the 5 series with the CF₃ group showed lower color intensity, dielectric constants, and better solubility. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2399–2412, 2005     

Influence of semi‐crystalline poly(ε‐caprolactone) and non‐crystalline polylactide blocks on the thermal properties of polydimethylsiloxane‐based block copolymers

Poly(A)‐block‐poly(B), poly(A)‐block‐poly(B)‐block‐poly(A) and B(A)₂ block copolymers were prepared through coordinated anionic ring‐opening polymerization of ε‐caprolactone (CL) and lactic acid (LA) using hydroxy‐terminated polydimethylsiloxane (PDMS) as initiator. A wide range of well‐defined combinations of PDMS‐block‐PCL and PDMS‐block‐PLA diblock copolymers, PCL‐block‐PDMS‐block‐PCL and PLA‐block‐PDMS‐block‐PLA triblock copolymers and star‐PDMS(PCL)₂ copolymers were thus obtained. The number‐average molar masses and the structure of the synthesized block copolymers were identified using various analytical techniques. The thermal properties of these copolymers were established using differential scanning calorimetry. Considering PDMS‐block‐PCL copolymers, the results demonstrate the complex effect of polymer architecture and PCL block length on the ability of the PDMS block to crystallize or not. In the case of diblock copolymers, crystallization of PCL blocks originated from stacking of adjacent chains inducing the extension of the PDMS block that can easily crystallize. In the case of star copolymers, the same tendency as in triblock copolymers is observed, showing a limited crystallization of PDMS when the length of the PCL block increases. In the case of PDMS‐block‐PLA copolymers, melting and crystallization transitions of the PLA block are never observed. Considering the diblock copolymers, PDMS sequences have the ability to crystallize. © 2019 Society of Chemical Industry     

Characterization and CO2 sorption properties of poly[methacryloxypropylheptacyclopentyl‐T8‐silsesquioxane‐ co‐3‐methacryloxypropyltris(trimethylsiloxy)silane]

Poly[methacryloxypropylheptacyclopentyl‐T8‐silsesquioxane (MAPOSS)‐co‐3‐methacryloxypropyltris(trimethylsiloxy)silane (SiMA)] was synthesized through free radical polymerization. The physical and carbon dioxide (CO₂) sorption properties of the copolymer membranes were investigated in terms of the MAPOSS content. As the MAPOSS content increases, the membrane density increased, suggesting a decrease in the fractional free volume. In addition, the thermal stability was improved with increasing the MAPOSS content. These are because of the polyhedraloligomericilsesquioxane (POSS) units that restrict the high mobility of poly(SiMA) segments. The glass transition temperature, T_g of the copolymers was single T_g based on the differential scanning calorimetry, suggesting that the copolymers were random and not phase separation. Based on the CO₂ sorption measurement, the POSS units play a role in reducing Henry's dissolution by suppressing the mobility of the poly(SiMA) component, while POSS units increase the nonequilibrium excess free volume, which contributes to the Langmuir dissolution. Based on these results, the introduction of MAPOSS unit is one of the effective ways to improved the thermal stability and CO₂ sorption property due to the enhancement of the polymer rigidity. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Energy‐transfer method to study vapor‐induced latex film formation

Nonradiative energy transfer method was used to study latex film formation induced by organic solvent vapor. Seven different films with the same latex content were prepared separately from poly(methyl methacrylate) (PMMA) particles and exposed to ethyl benzene, toluene, chloroform, dichloromethane, tetrahydrofuran, and acetone vapor in seven different experiments. Energy‐transfer experiments were carried out between PMMA‐bound naphthalene (N) and pyrene (P) during vapor‐induced film formation. Latex films were prepared from equal amounts of N‐ and P‐labeled latex particles, and steady state spectra of N and P were monitored during film formation. It was observed that the P to N intensity ratio, I_P/I_N, increased as the vapor exposure time increased. The Prager–Tirrell (PT) model was employed to obtain back‐and‐forth frequencies, ν, of the reptating PMMA chains during latex film formation induced by solvent vapor. ν values were obtained and found to be correlated with the solubility parameter, δ. Polymer interdiffusion obeyed the t^1/2 law during film formation. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 632–645, 2002; DOI 10.1002/app.10346     

Synthesis and characterization of AB‐type copolymers poly(L‐lactide)‐block‐poly(methyl methacrylate) via a convenient route combining ROP and ATRP from a dual initiator

Diblock copolymers of poly(L ‐lactide)‐block‐poly(methyl methacrylate) (PLLA‐b‐PMMA) were synthesized through a sequential two‐step strategy, which combines ring‐opening polymerization (ROP) and atom transfer radical polymerization (ATRP), using a bifunctional initiator, 2,2,2‐trichloroethanol. The trichloro‐terminated poly(L ‐lactide) (PLLA‐Cl) with high molecular weight (M_n,GPC = 1–12 × 10⁴ g/mol) was presynthesized through bulk ROP of L ‐lactide (L ‐LA), initiated by the hydroxyl group of the double‐headed initiator, with tin(II) octoate (Sn(Oct)₂) as catalyst. The second segment of the block copolymer was synthesized by the ATRP of methyl methacrylate (MMA), with PLLA‐Cl as macroinitiator and CuCl/N,N,N′,N″,N″‐pentamethyldiethylenetriamine (PMDETA) as catalyst, and dimethyl sulfoxide (DMSO) was chosen as reaction medium due to the poor solubility of the macroinitiator in conventional solvents at the reaction temperature. The trichloroethoxyl terminal group of the macroinitiator was confirmed by Fourier transform infrared spectroscopy (FTIR) and ¹H‐NMR spectroscopy. The comprehensive results from GPC, FTIR, ¹H‐NMR analysis indicate that diblock copolymers PLLA‐b‐PMMA (M_n,GPC = 5–13 × 10⁴ g/mol) with desired molecular composition were obtained by changing the molar ratio of monomer/initiator. DSC, XRD, and TG analyses establish that the crystallization of copolymers is inhibited with the introduction of PMMA segment, which will be beneficial to ameliorating the brittleness, and furthermore, to improving the thermal performance. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Morphology and rheological behavior of maltene–polymer blends. I. Effect of partial hydrogenation of poly(styrene‐block‐butadiene‐block‐styrene‐block)‐type copolymers

Because of the importance of the maltene–polymer interaction for the better performance of polymer‐modified asphalts, this article reports the effects of the molecular characteristics of two commercial poly(styrene‐block‐butadiene‐block‐styrene‐block) (SBS) polymers and their partially hydrogenated derivatives [poly{styrene‐block[(butadiene)_1?x–(ethylene‐co‐butylene)_x]‐block‐styrene‐block} (SBEBS)] on the morphology and rheological behavior of maltene–polymer blends (MPBs) with polymer concentrations of 3 and 10% (w/w). Each SBEBS and its parent SBS had the same molecular weight and polystyrene block size, but they differed from each other in the composition of the elastomeric block, which exhibited the semicrystalline characteristics of SBEBS. Maltenes were obtained from Ac‐20 asphalt (Pemex, Salamanca, Mexico), and the blends were prepared by a hot‐mixing procedure. Fluorescence microscopy images indicated that all the blends were heterogeneous, with polymer‐rich and maltene‐rich phases. The rheological behavior of the blends was determined from oscillatory shear flow data. An analysis of the storage modulus, loss modulus, complex modulus, and phase angle as a function of the oscillatory frequency at various temperatures allowed us to conclude that the maltenes behaved as pseudohomogeneous viscoelastic materials that could dissipate stress without presenting structural changes; moreover, all the MPBs were more viscoelastic than the neat maltenes, and this depended on both the characteristics and amount of the polymer. The MPBs prepared with SBEBS were more viscoelastic and possessed higher elasticity than those prepared with SBS. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis,characterization and biocompatibility of novel biodegradable poly[((R)‐3‐hydroxybutyrate)‐block‐(D,L‐lactide)‐block‐(ε‐caprolactone)] triblock copolymers

BACKGROUND: Biodegradable block copolymers have attracted particular attention in both fundamental and applied research because of their unique chain architecture, biodegradability and biocompatibility. Hence, biodegradable poly[((R )‐3 ‐hydroxybutyrate)‐block‐(D ,L ‐lactide)‐block‐(ε‐caprolactone)] (PHB‐PLA‐PCL) triblock copolymers were synthesized, characterized and evaluated for their biocompatibility. RESULTS: The results from nuclear magnetic resonance spectroscopy, gel permeation chromatography and thermogravimetric analysis showed that the novel triblock copolymers were successfully synthesized. Differential scanning calorimetry and wide‐angle X‐ray diffraction showed that the crystallinity of PHB in the copolymers decreased compared with methyl‐PHB (LMPHB) oligomer precursor. Blood compatibility experiments showed that the blood coagulation time became longer accompanied by a reduced number of platelets adhering to films of the copolymers with decreasing PHB content in the triblocks. Murine osteoblast MC3T3‐E1 cells cultured on the triblock copolymer films spread and proliferated significantly better compared with their growth on homopolymers of PHB, PLA and PCL, respectively. CONCLUSION: For the first time, PHB‐PLA‐PCL triblock copolymers were synthesized using low molecular weight LMPHB oligomer as the macroinitiator through ring‐opening polymerization with D ,L ‐lactide and ε‐caprolactone. The triblock copolymers exhibited flexible properties with good biocompatibility; they could be developed into promising biomedical materials for in vivo applications. Copyright © 2008 Society of Chemical Industry     

Miscibility and crystallization kinetics of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/ poly(methyl methacrylate) blends

The miscibility and crystallization kinetics of the blends of random poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) [P(HB‐co‐HV)] copolymer and poly(methyl methacrylate) (PMMA) were investigated by differential scanning calorimetry (DSC) and polarized optical microscopy (POM). It was found that P(HB‐co‐HV)/PMMA blends were miscible in the melt. Thus the single glass‐transition temperature (T_g) of the blends within the whole composition range suggests that P(HB‐co‐HV) and PMMA were totally miscible for the miscible blends. The equilibrium melting point (T°_m) of P(HB‐co‐HV) in the P(HB‐co‐HV)/PMMA blends decreased with increasing PMMA. The T°_m depression supports the miscibility of the blends. With respect to the results of crystallization kinetics, it was found that both the spherulitic growth rate and the overall crystallization rate decreased with the addition of PMMA. The kinetics retardation was attributed to the decrease in P(HB‐co‐HV) molecular mobility and dilution of P(HB‐co‐HV) concentration resulting from the addition of PMMA, which has a higher T_g. According to secondary nucleation theory, the kinetics of spherulitic crystallization of P(HB‐co‐HV) in the blends was analyzed in the studied temperature range. The crystallizations of P(HB‐co‐HV) in P(HB‐co‐HV)/PMMA blends were assigned to n = 4, regime III growth process. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3595–3603, 2004     

Property improvement of plasticized poly(vinyl chloride) by nano‐TiO2 and poly(methyl methacrylate)–encapsulated nano‐TiO2

To improve the physical properties of plasticized poly(vinyl chloride) (p‐PVC), the p‐PVC nanocomposites filled with four loading levels (3, 5, 7, and 9 parts per hundred of PVC resin) of either nanosized titanium dioxide (nTiO₂) or poly(methyl methacrylate)–encapsulated nTiO₂ (PMMA‐nTiO₂) were prepared by melt mixing on a two‐roll mill, followed by compression molding. The PMMA‐nTiO₂ used in this study was synthesized via in situ differential microemulsion polymerization. The resulting PMMA‐nTiO₂ exhibited core‐shell morphology (nTiO₂ core and PMMA shell) with an average diameter of 42.6 nm. The effects of nTiO₂ and PMMA‐nTiO₂ on the tensile properties, hardness, morphology, and thermal stability of the as‐prepared p‐PVC nanocomposites were then investigated and compared. The inclusion of either nTiO₂ or PMMA‐nTiO₂ nanoparticles increased the tensile strength, Young's modulus, hardness, and thermal stability of the nanocomposites in a dose‐dependent manner and reduced the elongation at break. However, the elongation at break was still higher than that for the neat p‐PVC. Moreover, the PMMA‐nTiO₂ nanocomposites had a higher enhancement of the tensile strength, Young's modulus, hardness, and thermal stability than the nTiO₂ nanocomposites at a similar loading level. Hence, the PMMA grafted on the nTiO₂ surface played an important role in toughening and increasing the thermal stability of the nanocomposites owing to the improved miscibility and interfacial adhesion between the encapsulated nanofiller and PVC matrix. J. VINYL ADDIT. TECHNOL., 22:433–440, 2016. © 2015 Society of Plastics Engineers     

Synthesis of PMMA‐PTHF‐PMMA and PMMA‐PTHF‐PST linear and star block copolymers

Combination of cationic, redox free radical, and thermal free radical polymerizations was performed to obtain linear and star polytetramethylene oxide (poly‐THF)‐polymethyl methacrylate (PMMA)/polystyrene (PSt) multiblock copolymers. Cationic polymerization of THF was initiated by the mixture of AgSbF₆ and bis(4,4′ bromo‐methyl benzoyl) peroxide (BBP) or bis (3,5,3′,5′ dibromomethyl benzoyl) peroxide (BDBP) at 20°C to obtain linear and star poly‐THF initiators with M_w varying from 7,500 to 59,000 Da. Poly‐THF samples with hydroxyl ends were used in the methyl methacrylate (MMA) polymerization in the presence of Ce(IV) salt at 40°C to obtain poly(THF‐b‐MMA) block copolymers containing the peroxide group in the middle. Poly(MMA‐b‐THF) linear and star block copolymers having the peroxide group in the chain were used in the polymerization of methyl methacrylate (MMA) and styrene (St) at 80°C to obtain PMMA‐b‐PTHF‐b‐PMMA and PMMA‐b‐PTHF‐b‐PSt linear and star multiblock copolymers. Polymers obtained were characterizated by GPC, FT‐IR, DSC, TGA, ¹H‐NMR, and ¹³C‐NMR techniques and the fractional precipitation method. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 219–226, 2004     

Water transport properties in poly(3‐hydroxybutyrate) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) biopolymers

Water sorption and diffusion have been investigated in poly(3‐hydroxybutyrate) (PHB) and three poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) copolymers [P(HB‐HV)] by means of a Cahn electromicrobalance. Permeability of these samples have been determined using a gravimetric permeation cell. Two experimental setups were used for the gravimetric sorption measurements, under dynamic and static conditions, respectively. The differences observed in the results obtained using these techniques are discussed. The sorption measurements have evidenced the tendency of water molecules to form aggregates or clusters in the polymer. In addition, the static sorption method revealed the potential of PHB and P(HB‐HV) to undergo molecular relaxations, eventually leading to a partial desorption of the previously sorbed water after an induction period. The clustering effect was adequately described by the polycondensation model. On the other hand, the interpretation of the diffusivity in terms of mobility coefficients has revealed a competition between a plasticization effect and clustering. As a whole, water transport properties in PHB and its copolymers can be considered to be very close in magnitude to those of common thermoplastics such as PVC and PET. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 455–468, 1999