Mechanical properties and viscoelastic behavior of basalt fiber‐reinforced polypropylene

In the present article, a series of commercial‐grade polypropylenes (PP) filled with different contents of short basalt fibers were studied. This composite material presented deterioration of both mechanical characteristics, for example, stress and strain at yield with increasing of the fiber content. On the other hand, the impact strength was fourfold higher than that of unfilled PP. A poor adhesion between the PP matrix and the basalt fibers was detected. This is why interfacial interactions were promoted by the adding of poly(propylene‐g‐maleic anhydride) (PP‐g‐MA). It was observed that the tensile properties of the obtained materials and their impact strengths increased significantly with increasing of the amount of PP‐g‐MA in the blend. The adhesion improvement was confirmed by scanning electron microscopy as well. Fourier transform infrared spectroscopy was applied to assess if any chemical interactions in the system PP/PP‐g‐MA/basalt fibers exist. Dynamic mechanical thermal analysis data showed an increase of the storage modulus with increasing fiber content. The conclusion was made that the modification of the PP matrix led to a higher stiffness but its value remained constant, irrespective of the PP‐g‐MA content. With increasing fiber content, damping in the β‐region decreased, but increase of the coupling agent content restored its value back to that of PP. The loss modulus spectra presented a strong influence of fiber content on the α‐relaxation process of PP. The position of the peaks of the above‐mentioned relaxation processes are discussed as well. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 523–531, 1999     

Preparation and mechanical properties of high‐performance short ramie fiber‐reinforced polypropylene composites

Short ramie fiber (RF) was used to reinforce the polypropylene (PP). The composites were prepared in a twin‐screw extruder followed by injection molding. The experimental results showed that both the strength and the modulus of the composites increase considerably with increasing RF content. The tensile strength and flexural strength are as high as 67 and 80 MPa by the incorporation of ramie up to 30 wt %. To the best of our knowledge, this is one of the best results for short natural fiber‐reinforced PP composites. However, the preparation method in this study is more simple and economic. This short RF‐reinforced PP composites extend the application field for short‐nature fiber‐reinforced PP composites. Morphological analysis revealed that it is the high aspect ratio of the fiber and good interfacial compatibility that result in the high performance of the composites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

The effect of fiber concentration on mechanical and thermal properties of fiber‐reinforced polypropylene composites

A novel composite material consisting of polypropylene (PP) fibers in a random poly(propylene‐co‐ethylene) (PPE) matrix was prepared and its properties were evaluated. The thermal and mechanical properties of PP–PPE composites were studied by dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC) with reference to the fiber concentration. Although, by increasing PP fiber concentration in PPE, no significant difference was found in melting and crystallization temperatures of the PPE, the storage, and the tensile and flexural modulus of the composites increased linearly with fiber concentrations up to 50%, 1.5, 1.0, 1.3 GPa, respectively, which was approximately four times higher than that for the pure PPE. There is a shift in glass transition temperature of the composite with increasing fiber concentration in the composite and the damping peak became flatter, which indicates the effectiveness of fiber–matrix interaction. A higher concentration of long fibers (>50% w/w) resulted in fiber packing problems, difficulty in dispersion, and an increase in void content, which led to a reduction in modulus. Cox–Krenchel and Haplin–Tsai equations were used to predict tensile modulus of random fiber‐reinforced composites. A Cole–Cole analysis was performed to understand the phase behavior of the composites. A master curve was constructed based on time–temperature superposition (TTS) by using data over the temperature range from −50 to 90°C, which allowed for the prediction of very long and short time behavior of the composite. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2260–2272, 2005     

Crystallization,melting behavior,and crystal structure of reactive,intumescent, flame‐retardant polypropylene

Polypropylene (PP)/2‐({9‐[(4,6‐diamino‐1,3,5‐triazin‐2‐yl) amino]‐3,9‐dioxido‐2,4,8,10‐tetraoxa‐3,9‐diphosphaspiro [5.5] undecan‐3‐yl} oxy) ethyl methacrylate (EADP) composites were prepared by the blending of PP with EADP as a new flame‐retardant material. The nonisothermal crystallization and melting behaviors of composites were investigated with differential scanning calorimetry (DSC). Their crystal morphologies and structures were studied by polarized optical microscopy (POM) and X‐ray diffraction (XRD), respectively. The DSC results show that the addition of EADP increased the crystallization onset temperature, crystallization peak temperature, and degree of crystallinity of PP in the PP/EADP composites. The melting onset temperature and melting end temperature of the PP/EADP composites decreased slightly, whereas the melting peak temperature of the PP/EADP composites increased. The POM results show that the addition of EADP greatly reduced the crystal size of PP in the composites. When the content of EADP in the PP/EADP composites was increased, the crystal size of PP became smaller. The XRD results indicate that the addition of EADP changed the crystal structure of PP in the PP/EADP composites, which exhibited both α‐form and β‐form crystal structures. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41374.     

Dynamic mechanical properties,crystallization behaviors,and low‐temperature performance of polypropylene random copolymer composites

In this study, polypropylene random copolymer (PPR) composites were prepared by the addition of either three kinds of thermoplastic rubber (TPR) modifiers (types 2088A, 2095, and 2096) or an ethylene–octene copolymer (POE)/high‐density polyethylene (HDPE; 2 :1 w/w) blend. Differential scanning calorimetry, wide‐angle X‐ray diffraction, and dynamic mechanical analysis were used to characterize the crystallization behaviors and dynamic mechanical properties of the PPR composites. The results indicated that PPR/POE/HDPE and PPR/TPR2088A had better comprehensive mechanical properties, especially the low‐temperature toughness among all of the samples. The obtained PPR/POE/HDPE blends showed a high toughness and good stiffness in the temperature interval from ?10 to 23°C with the addition of only 10 wt % POE/HDPE. When the temperature continued to fall below ?10°C, the PPR/TPR2088A composites exhibited a better impact toughness without a loss of too much stiffness. The good low‐temperature toughness of those two composites was attributed to both the decrease in the crystallinity and the uniform dispersion, obvious interfacial adhesion, and cavitation ability of POE/HDPE and TPR2088A in the PPR matrix. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42960.     

A highly efficient β‐nucleating agent for impact‐resistant polypropylene copolymer

In this work, we reported calcium tetrahydrophthalate as a high efficient β‐nucleating agent (β‐NA) for impact‐resistant polypropylene copolymer (IPC). The relative fraction of the β‐crystal can reach as high as 93.5% when only 0.03% β‐NA is added. The non‐isothermal and isothermal crystallization behaviors, morphology, lamellar structure and mechanical properties of IPCs with various β‐NA contents were studied. During non‐isothermal crystallization, the cooling rate has an important influence on the relative fraction of the β‐crystal, which decreases remarkably as the cooling rate increases. The β‐NA also greatly accelerates crystallization rate of IPC, resulting from both more crystal nuclei and larger Avrami exponent. The small angle X‐ray scattering characterization shows that more amorphous components are included into the inter‐lamellae after addition of β‐NA. Dynamical mechanical analysis (DMA) reveals that the storage modulus at low temperature and the loss factor above 0 °C from the PP component can be enhanced upon addition of β‐NA and reach a maximum at the β‐NA content of 0.05 wt %. Impact test shows that the impact strength of the IPC at 0°C can be improved as much as 40% when the content of calcium tetrahydrophthalate is 0.10 wt %. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40753.     

A highly active and selective β‐nucleating agent for isotactic polypropylene and crystallization behavior of β‐nucleated isotactic polypropylene under rapid cooling

Zinc adipate (Adi‐Zn) was observed to be a highly active and selective β‐nucleating agent for isotactic polypropylene (iPP). The effects of Adi‐Zn on the mechanical properties and the β‐crystals content of nucleated iPP were investigated. The impact strength of iPP nucleated with 0.2 wt % Adi‐Zn was 1.8 times higher than that of neat iPP. In addition, wide‐angle X‐ray diffraction analysis indicated that the content of β‐crystals in nucleated iPP (k_β value) reached 0.973 with 0.1 wt % Adi‐Zn, indicating that Adi‐Zn is a highly active and selective β‐nucleating agent for iPP. Furthermore, fast scanning chip calorimetry (FSC) studies using cooling rates from 60 to 13,800 °C min^?1 revealed that the formation of β‐crystals significantly depended on the cooling rates. At cooling rates below 3000 °C min^?1, only β‐crystals existed. However, at cooling rates above 6000 °C min^?1, β‐crystals failed to form. Moreover, a lower critical crystallization temperature that corresponded to the generation of β‐crystals was investigated using cooling‐induced crystallization, and the results are in good agreement with those of a previous study. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43767.     

Crystallization and mechanical properties of isotactic polypropylene/calcium carbonate nanocomposites with a stratified distribution of calcium carbonate

Isotactic polypropylene (iPP)/calcium carbonate (CaCO₃) nanocomposites with a stratified distribution of CaCO₃ were prepared by two‐step molding. The iPP and CaCO₃ nanoparticles were first mixed by a batch mixer and then compressed into thin layers. Thin iPP/CaCO₃ layers alternating with thin neat iPP layers were finally compressed together to form the stratified samples. The transcrystals were observed in the stratified samples by polarized optical microscopy and scanning electron microscopy. The transcrystals grew from the surfaces of the filled layers and occupied most of the space in the neat iPP layers. The β‐form crystals were found in the stratified samples with thick transcrystalline layers, whereas the thickness of the transcrystalline layer was dependent on the content of CaCO₃ nanoparticles and the cooling rate of the processing. The relative crystallinity index of the conventional samples first increased and then decreased with the content of CaCO₃ nanoparticles. However, the relative crystallinity index of the stratified samples deceased slightly with the content of CaCO₃ nanoparticles because of the stratified distribution of the CaCO₃ nanoparticles. The stratified samples, except for the samples with high β‐form contents, became more brittle than the conventional samples because of the transcrystal formation in the iPP layers. The stratified samples with high β‐form contents showed much better mechanical properties than the conventional samples. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39632.     

Preparation,dynamic rheological behavior,crystallization, and mechanical properties of inorganic whiskers reinforced polylactic acid/hydroxyapatite nanocomposites

The novel inorganic SiO₂–MgO–CaO whiskers (SMCWs) were incorporated into nano hydroxyapatite (HA) contained polylactic acid (PLA) system to prepare the reinforced PLA/HA/SMCWs nanocomposite. Maleic anhydride grafted PLA (PLA‐g‐MAH) was then used to modify the interface between filler and matrix. The morphology, rheological behavior, crystallization, and mechanical property of the prepared nanocomposites were systematically investigated using scanning electronic microscope, dynamic rheometer, differential scanning calorimeter, polarized light microscope, and mechanical test, respectively. The results showed that the introduced PLA‐g‐MAH obviously improves the filler dispersion and the filler–matrix interfacial compatibility. Interestingly, the incorporated whiskers obviously decrease the complex viscosity and hence could significantly improve the processability of system. However, the introduction of PLA‐g‐MAH increases the complex viscosity to a greater extent. In addition, the added whiskers were found to have complicated influences on the PLA crystallization. On one hand, the incorporated whiskers can enhance the melt crystallization capability of PLA macromolecular chains; on the other hand, the introduced whiskers also show the inhibitive effect on the nucleation of PLA polymer chains and the inhibition degree is related to the loading of whiskers. The combination of whiskers and PLA‐g‐MAH could remarkably improve the mechanical performance of PLA/HA nanocomposite. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43381.     

Crystallization behavior of ultrahigh‐molecular‐weight polyethylene/polyhedral oligomeric silsesquioxane nanocomposites prepared by ethylene in situ polymerization

A [3‐t‐Bu‐2‐O? C₆H₃CH?N(C₆F₅)]₂TiCl₂ catalyst (bis(phenoxyimine)titanium dichloride complex – FI catalyst) was immobilized on disilanolisobutyl polyhedral oligomeric silsesquioxane (OH‐POSS) to prepare ultrahigh molecular‐weight polyethylene (UHMWPE)/polyhedral oligomeric silsesquioxane (POSS) nanocomposites during ethylene in situ polymerization. The dispersion state of POSS in the UHMWPE matrix was characterized by X‐ray diffraction measurements and transmission electron microscopy. It was shown that the OH‐POSS achieved uniformed dispersion in the UHMWPE matrix, although its polarity was unmatched. The isothermal and nonisothermal crystallization behavior of the nanocomposites was investigated by means of differential scanning calorimetry. The crystallization rate of the nanocomposites was enhanced because of the incorporation of POSS during the isothermal crystallization. POSS acted as a nucleus for the initial nucleation and the subsequent growth of the crystallites. For nonisothermal studies, POSS showed an increase in the crystallinity. The crystallization rate of the nanocomposites decreased because the presence of POSS hindered the crystal growth. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40847.     

Interfacial influence on mechanical properties of polypropylene/polypropylene‐grafted silica nanocomposites

Three types of polypropylene‐grafted silica (PGS‐2 K, PGS‐8 K and PGS‐30 K) with different grafting chain lengths were prepared. After melt‐blending PGS with polypropylene (PP), we studied the PP/PGS interface properties and the influence of PP/PGS interfaces on mechanical properties of nanocomposites. The strong matrix/particle interface was observed in PP/PGS‐30 K nanocomposites with 5 wt % particle loading as evidenced by 2.5 °C increased glass transition temperature (T_g) compared with neat PP, whereas the weak matrix/particle interface was observed in PP/PGS‐2 K nanocomposites with decreased T_g. The variations in the matrix/particle interfacial strength lead to a transition in the yield stress of nanocomposites. Compared with the unfilled PP, the yield stress of the PP/PGS‐2 K nanocomposites is decreased by 0.7 MPa, and the yield stress of the PP/PGS‐30 K nanocomposites is enhanced by 1.4 MPa. In addition, benefiting from good dispersion, the PP/PGS‐masterbatch nanocomposites with a strong matrix/particle interface not only exhibit increased Young's modulus and yield stress, but also the strain at break remains in line with the unfilled PP, which is in contrast to the conventional wisdom that the gain in modulus and strength must be at the expense of the decreased break strain. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45887.     

Role of crystalline ethylene‐propylene copolymer on mechanical properties of impact polypropylene copolymer

Impact polypropylene copolymer (IPC) has been known as a multiphase material in which an ethylene‐propylene (EP) random copolymer, serves as toughening component, is dispersed in the homo‐polypropylene hPP matrix. The crystalline EP copolymer (cEP) is another component whose role and microstructural effect on the IPC properties has not been well understood. This work reveals the relationship between the microstructure of cEP and the mechanical properties, that is, impact and tensile resistance, of IPC. We clarify that IPC comprising high contents of cEP with long homo‐PP segment can extend the elongation at break while cEP with high content of homo‐PE segment contributes to high impact strength. Mechanisms for both of these processes have been proposed. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Characterization and mechanical properties of exfoliated graphite nanoplatelets reinforced polyethylene terephthalate/polypropylene composites

Recently, graphene and its derivatives have been used to develop polymer composites with improved or multifunctional properties. Exfoliated graphite nanoplatelets (GNP) reinforced composite materials based on blend of polyethylene terephthalate (PET), and polypropylene (PP) compatibilized with styrene–ethylene–butylene–styrene‐g‐maleic anhydride is prepared by melt extrusion followed by injection molding. Characterization of the composites' microstructure and morphology was conducted using field emission scanning electron microscopy, transmission electron microscopy (TEM), X‐ray diffraction analysis (XRD), and Fourier transform infrared spectroscopy (FTIR). Tensile and impact strengths of test specimens were evaluated and the results showed maximum values at 3phr GNP in both the cases. Morphological studies showed that the GNPs were uniformly dispersed within the matrix. Results from XRD analysis showed uniformly dispersed GNPs, which may not have been substantially exfoliated. FTIR spectroscopy did not show any significant change in the peak positions to suggest definitive chemical interaction between GNP and the matrix. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40582.     

Bleached extruder chemi‐mechanical pulp fiber‐PLA composites: Comparison of mechanical,thermal, and rheological properties with those of wood flour‐PLA bio‐composites

An environmentally friendly bleached extruder chemi‐mechanical pulp fiber or wood flour was melt compounded with poly(lactic acid) (PLA) into a biocomposite and hot compression molded. The mechanical, thermal, and rheological properties were determined. The chemical composition, scanning electron microscopy, and Fourier transform infrared spectroscopy results showed that the hemicellulose in the pulp fiber raw material was almost completely removed after the pulp treatment. The mechanical tests indicated that the pulp fiber increased the tensile and flexural moduli and decreased the tensile, flexural, and impact strengths of the biocomposites. However, pulp fiber strongly reinforced the PLA matrix because the mechanical properties of pulp fiber‐PLA composites (especially the tensile and flexural strengths) were better than those of wood flour‐PLA composites. Differential scanning calorimetry analysis confirmed that both pulp fiber and wood flour accelerated the cold crystallization rate and increased the degree of crystallinity of PLA, and that this effect was greater with 40% pulp fiber. The addition of pulp fiber and wood flour modified the rheological behavior because the composite viscosity increased in the presence of fibers and decreased as the test frequency increased. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44241.     

Tribological behavior of short‐fiber‐reinforced polyimide composites under dry‐sliding and water‐lubricated conditions

Polyimide composites reinforced with short‐cut fibers such as carbon, glass, and quartz fibers were fabricated by the polymerization of monomer reactants process. The mechanical properties of the composites with different fiber contents were evaluated. The friction and wear properties of the polyimide and its composites were investigated under dry‐sliding and water‐lubricated conditions. The results indicated that the short‐carbon‐fiber‐reinforced polyimide composites had better tensile and flexural strengths and improved tribological properties in comparison with glass‐fiber‐ and quartz‐fiber‐reinforced polyimide composites. The incorporation of short carbon fibers into the polyimide contributed to decreases in the friction coefficient and wear rate under both dry and water‐lubricated conditions and especially under water lubrication because of the boundary lubrication effect of water. The polyimide and its composites were characterized by plastic deformation, microcracking, and spalling under both dry and water‐lubricated conditions, which were significantly abated under the water‐lubricated condition. The glass and quartz fibers were easily abraded and broken; the broken fibers transferred to the mating metal surface and increased the surface roughness of mating stainless steel, which led to the wear rate increasing for the glass‐fiber‐ and quartz‐fiber‐reinforced polyimide composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Mechanical behavior of agro‐residue‐reinforced polypropylene composites

In this research, fully environment‐friendly, sustainable and biodegradable composites were fabricated, using wheat straw and rice husk as reinforcements for thermoplastics, as an alternative to wood fibers. Mechanical properties including tensile, flexural, and impact strength properties were examined as a function of the amount of fiber and coupling agent used. In the sample preparation, three levels of fiber loading (30, 40, and 50 wt %) and two levels of coupling agent content (0 and 2 wt %) were used. As the percentage of fiber loading increased, flexural and tensile properties increased significantly. Notched Izod results showed a decrease in strength as the percentage of fiber increases. With addition of 50% fiber, the impact strengths decreased to 16.3, 14.4, and 16.4 J/m respectively, for wheat straw‐, rice husk‐, and poplar‐filled composites. In general, presence of coupling agent had a great effect on the mechanical strength properties. Wheat straw‐ and rice husk‐filled composites showed an increase in the tensile and flexural properties with the incorporation of the coupling agent. From these results, we can conclude that wheat straw and rice husk fibers can be potentially suitable raw materials for manufacturing biocomposite products. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Thermal and mechanical properties of polypropylene/wood‐flour composites

In this research, polypropylene/wood‐flour composites (WPCs) were blended with different contents of wood and/or maleated polypropylene (MAPP) and clay. We found that the addition of MAPP or clay in the formulation greatly improved the dispersion of the wood fibers in the composite; this suggested that MAPP or clay may have played the role of an adhesion promoter in the WPCs. The results obtained with clay indicate that it also acted as a flame retardant. The thermal tests carried out with the produced samples showed an increased crystallization temperature (T_c), crystallinity, and melting temperature (T_m) with wood loading. The increase of the two former parameters was explained by the incorporation of wood flour, which played the role of nucleating agent and induced the crystallization of the matrix polymer. On the other hand, the T_m increase was ascribed to the insulating properties of wood, which hindered the movement of heat conduction. The effects of UV irradiation on T_m and T_c were also examined. T_c increased with UV exposure time; this implied that UV degradation generated short chains with low molecular weight that could move easily in the bulk of the sample and, thus, catalyze early crystallization. The flexural strength and modulus increased with increasing wood‐flour content. In contrast, the impact strength and tensile strength and strain decreased with increasing wood‐flour content. All of these changes were related to the level of dispersion of the wood flour in the polymeric matrix. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Investigation of mechanical properties of alumina nanoparticle‐loaded hybrid glass/carbon‐fiber‐reinforced epoxy composites

This research work investigates the tensile strength and elastic modulus of the alumina nanoparticles, glass fiber, and carbon fiber reinforced epoxy composites. The first type composites were made by adding 1–5 wt % (in the interval of 1%) of alumina to the epoxy matrix, whereas the second and third categories of composites were made by adding 1–5 wt % short glass, carbon fibers to the matrix. A fourth type of composite has also been synthesized by incorporating both alumina particles (2 wt %) and fibers to the epoxy. Results showed that the longitudinal modulus has significantly improved because of the filler additions. Both tensile strength and modulus are further better for hybrid composites consisting both alumina particles and glass fibers or carbon fibers. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39749.     

Short sisal fiber‐reinforced tire rubber composites: Dynamic and mechanical properties

The world tendency toward using recycled materials demands new products from vegetable resources and waste polymers. In this work, composites made from powdered tire rubber (average particle size: 320 μm) and sisal fiber were prepared by hot‐press molding and investigated by means of dynamic mechanical thermal analysis and tensile properties. The effects of fiber length and content, chemical treatments, and temperature on dynamic mechanical and tensile properties of such composites were studied. The results showed that mercerization/acetylation treatment of the fibers improves composite performance. Under the conditions investigated the optimum fiber length obtained for the tire rubber matrix was 10 mm. Storage and loss moduli both increased with increasing fiber content. The results of this study are encouraging, demonstrating that the use of tire rubber and sisal fiber in composites offers promising potential for nonstructural applications. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 670–677, 2004     

Carbon fiber‐reinforced gelatin composites. I. Preparation and mechanical properties

Composites were made from carbon fibers and gelatin using a solvent‐casting or solution‐impregnation technique. Relationships between the fiber volume fraction (Vf), glycerol (plasticizer) content, gelatin content, fiber form, and mechanical properties (tensile strength and modulus, elongation at break, and shear strength) of the composites were investigated. In long carbon fiber gelatin composite (C_L/Gel), tensile strength, modulus, and shear strength increased steadily with the Vf. In the case of a short carbon fiber gelatin composite (C_S/Gel), an initial improvement in tensile strength and modulus was followed by a reduction, whereas the shear strength improved with the Vf and then reached a constant value. The elongation decreased with the Vf for both composites. It is shown that C_L/Gel had higher values of strength, modulus, and elongation than did C_S/Gel at any Vf level. The effects of glycerol and gelatin contents on the mechanical properties of the composites were found to be much less significant as compared to the Vf. According to scanning electron microscopic observation of the fracture surfaces, the fibers were uniformly distributed in the gelatin matrix, but the interfacial adhesion between the gelatin matrix and the carbon fibers was not very good for both composites. Fiber surface modification would be necessary to further improve the mechanical properties of the two composites. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 987–993, 2000