Modeling of multicomponent mass diffusion in porous spherical pellets: Application to steam methane reforming and methanol synthesis

The main purpose of this paper is the derivation and evaluation of various diffusion flux models. For this aim, a comprehensive catalyst pellet problem has been simulated for two test cases: the steam methane reforming (SMR) and the methanol synthesis, as these two important chemical processes cover various aspects of a chemical reaction. The pressure, temperature, total concentration, species composition, viscous flow, mass and heat fluxes within the porous spherical pellet are included in the transient pellet model. Mass diffusion fluxes are described according to the rigorous Maxell–Stefan and dusty gas models, and the respectively simpler Wilke and Wilke–Bosanquet models. Simulations are performed with these fluxes defined according to both the molar averaged and mass averaged definitions. For the mass based pellet equations, a consistent set of equations is obtained holding only the mass averaged velocity. On the other hand, the closed set of molar based pellet equations hold both the molar averaged and mass averaged velocities as the fundamental energy balance and the momentum balance (Darcy law) are derived according to the mass averaged velocity definition, whereas the diffusion fluxes are defined relative to the molar averaged velocity. Identical results of the molar and mass based pellet equations were not obtained; however, the deviations are small. It is anticipated that these discrepancies are due to some unspecified numerical inaccuracies. However, efficiency factors have been computed for both processes and the values obtained compare well with the available literature data. Furthermore, efficiency factor sensitivity on parameters like pore diameter, tortuosity, temperature and pressure have been accomplished, and the classical simplifications of the pellet equations have been elucidated: isothermal condition, constant pressure, and neglecting viscous flow. The following conclusions are established for the reactor operating conditions used in the present work. The methanol synthesis: The simulation results of the methanol synthesis indicate that the classical assumptions are very fair for this process. Moreover, both Wilke and Wilke–Bosanquet models are good replacements for the more rigorous Maxwell–Stefan and dusty gas models. However, the simulation results are affected by Knudsen diffusion, thus the diffusion flux is most appropriately described by the Wilke–Bosanquet model. The SMR process: Knudsen diffusion hardly influences the results of the highly intraparticle diffusion limited SMR process. As the Wilke model does not necessarily conserve mass, we recommend the Maxwell–Stefan model because the simpler Wilke closure deviates with several percents. However, it is not elucidated whether these deviations are numerical problems arising from the large gradients of this process, or related to the choice of diffusion model. Isothermal and isobaric conditions can be assumed within the particle, but significant external temperature gradients are observed. Convective fluxes are much less than the diffusive fluxes, hence viscous flow can be neglected.     

Catalytic activity of atomized Ni3Al powder for hydrogen generation by methane steam reforming

The catalytic activity of Ni₃Al for methane steam reforming was investigated for the first time using its atomized powder. It was found that the activity was significantly enhanced by the combined pretreatment of acid and alkali leaching, while it was quite low for the as-received powder. The high activity was attributed to the formation of fine Ni particles on the porous surface of the powder.     

A fluidized bed membrane reactor for the steam reforming of methane

In the present investigation a realistic two-phase model accounting for the change in the total number of moles accompanying the reaction is utilized to explore a novel reactor configuration suggested for the methane steam reforming process. The suggested design is basically a fluidized bed reactor equipped with a bundle of membrane tubes. These tubes remove the main product, hydrogen, from the reacting gas mixture and drive the reaction beyond its thermodynamic equilibrium. The proposed novel design is also equipped with sodium heat pipes which act as a thermal flux transformer to provide the large amount of heat needed by the endothermic reaction through a relatively small heat transfer surface, assuring better reactor compactness. Two options for fluid routing through the membrane tubes are proposed; each is suitable for a certain industrial application. The performance of this novel configuration is compared with that of an industrial fixed bed steam reformer and the comparison shows the potential advantages of the suggested configuration.     

Modeling and simulation for the methane steam reforming enhanced by in situ CO2 removal utilizing the CaO carbonation for H2 production

The transient behavior of catalytic methane steam reforming (MSR) coupled with simultaneous carbon dioxide removal by carbonation of CaO pellets in a packed bed reactor for hydrogen production has been analyzed through a mathematical model with reaction experiments for model verification. A dynamic model has been developed to describe both the MSR reaction and the CaO carbonation-enhanced MSR reaction at non-isothermal, non-adiabatic, and non-isobaric operating conditions assuming that the rate of the CaO carbonation in a local zone of the packed bed is governed by kinetic limitation or by mass transfer limitation of the reactant CO₂. Apparent carbonation kinetics of the CaO pellet prepared has been determined using the TGA carbonation experiments at various temperatures, and incorporated into the model. The resulting model is shown to successfully depict the transient behavior of the in situ CaO carbonation-enhanced MSR reaction. The effects of major operating parameters on the transient behavior of the CaO carbonation-enhanced MSR have been investigated using the model. The bed temperature is the most important parameter for determining the amount of CO₂ removed by carbonation of CaO, and at temperatures of 600°C, 650°C, 700°C and 750°C, the CO₂ uptake is 1.43, 2.29, 3.5 and -CO₂/kg-CaO, respectively. Simultaneously with the increase in CO₂ uptake with increasing temperature, the corresponding amounts of hydrogen produced are 1.56, 2.54, 3.91 and -H₂/kg-CaO, at the same temperatures as above. Operation at high pressure, high steam to methane feed ratio, and the decreased feed rate at a given temperature are favorable for increasing the degree of the overall utilization of CaO pellets in the reactor bed, and for lowering the CO concentration in the product.     

Highly active and stable Rh/MgOAl2O3 catalysts for methane steam reforming

Highly active and coke-resistant Rh catalysts were developed for methane steam reforming in microchannel chemical reactors. Rh loading was optimized on a stable MgOAl₂O₃ support to improve the volumetric productivity for methane conversion. Catalyst activities were stable over a wide range of steam/carbon ratios. In particular, experimental results demonstrated that Rh/MgOAl₂O₃ catalysts are extremely active for methane steam reforming and are resistant to coke formation at stoichiometric steam/carbon ratio of 1 for over 14 h time-on-stream with no sign of deactivation. Methane steam reforming activities on this catalyst is compared in both a microchannel reactor and a conventional micro-tubular reactor. Significant performance enhancement was observed in microchannel reactors owing to improved heat and mass transfer.     

Combined catalytic partial oxidation and CO2 reforming of methane over supported cobalt catalysts

The combined partial oxidation and CO₂ reforming of methane to synthesis gas was investigated over the reduced Co/MgO, Co/CaO, and Co/SiO₂ catalysts. Only Co/MgO has proved to be a highly efficient and stable catalyst. It provided about 94–95% yields to H₂ and CO at the high space velocity of 105000 mlg^–1h^–1 and for feed ratios CH₄/CO₂/O₂=4/2/1, without any deactivation for a period of study of 110 h. In contrast, the reduced Co/CaO and Co/SiO₂ provided no activity for the formation of H₂ and CO. The structure and reducibility of the calcined catalysts were examined using X-ray diffraction and temperature-programmed reduction, respectively. A solid solution of CoO and MgO, which was difficult to reduce, was identified in the 800°C calcined MgO-supported catalyst. The strong interactions induced by the formation of the solid solution are responsible for its superior activity in the combined reaction. The effects of reaction temperature, space velocity, and O₂/CO₂ ratio in the feed gases (while keeping the C/O ratio constant at 1/1) were investigated over the Co/MgO catalyst. The H₂/CO ratio in the product of the combined reaction increased with increasing O₂/CO₂ ratio in the feed.     

Carbon-free dry reforming of methane to syngas over NdCoO3 perovskite-type mixed metal oxide catalyst

CoNdO_x (Co/Nd = 1) is a highly promising catalyst for the carbon-free CO₂ reforming of methane. Influence of the Co/Nd ratio on the catalyst performance in the CO₂ reforming and also on the crystalline phases and reduction by temperature programmed reduction (TPR) of the CoNdO_x catalyst has also been investigated. The CoNdO_x (CoNd = 1.0) catalyst consisted of mainly NdCoO₃ perovskite-type mixed metal oxide and it showed not only a high resistance to carbon formation at different process conditions (viz. temperature = 750–900 °C and gas hourly space velocity (GHSV) = 10000–50000 cm³ g^–1 h^–1) but also high activity and selectivity in the CO₂ reforming process. The high resistance to carbon formation for this catalyst is attributed mostly to strong metal (Co°)–support (Nd₂O₃) interactions.     

Computational study of staged membrane reactor configurations for methane steam reforming. II. Effect of number of stages and catalyst amount

The present work complements part I of this article and completes a computational analysis of the performances of staged membrane reactors for methane steam reforming. The influence of the number of stages and catalyst amount is investigated by comparing the methane conversion and hydrogen recovery yield achieved by an equisized‐staged reactor to those of an equivalent conventional membrane reactor for different furnace temperatures and flow configurations (co‐ and counter‐current). The most relevant result is that the proposed configuration with a sufficiently high number of stages and a significantly smaller catalyst amount (up to 70% lower) can achieve performances very close to the ones of the conventional unit in all the operating conditions considered. This is equivalent to say that the staged configuration can compensate and in fact substitute a significant part of the catalyst mass of a conventional membrane reactor. To help the interpretation of these results, stage‐by‐stage temperature and flux profiles are examined in detail. Then, the quantification of the performance losses with respect to the conventional reactor is carried out by evaluating the catalyst amount possibly saved and furnace temperature reduction. © 2009 American Institute of Chemical Engineers AIChE J, 2010     

Activity of different zeolite-supported Ni catalysts for methane reforming with carbon dioxide

The catalytic performance of Ni based on various types of zeolites (zeolite A, zeolite X, zeolite Y, and ZSM-5) prepared by incipient wetness impregnation has been investigated for the catalytic carbon dioxide reforming of methane into synthesis gas at 700 °C, at atmospheric pressure, and at a CH₄/CO₂ ratio of 1. It was found that Ni/zeolite Y showed better catalytic performance than the other types of studied zeolites. In addition, the stability of the Ni/zeolite Y was greatly superior to that of the other catalysts. A weight of Ni loading at 7 wt.% showed the best catalytic activity on each zeolite support; however, the 7% Ni catalysts produced a higher amount of coke than that of two other Ni loadings, 3 and 5%.     

Development of Ni-Pd bimetallic catalysts for the utilization of carbon dioxide and methane by dry reforming

The present research deals with catalyst development for the utilization of CO₂ in dry reforming of methane with the aim of reaching highest yield of the main product synthesis gas (CO, H₂) at lowest possible temperatures. Therefore, Ni-Pd bimetallic supported catalysts were prepared by simple impregnation method using various carriers. The catalytic performance of the catalysts was investigated at 500, 600 and 700 °C under atmospheric pressure and a CH₄ to CO₂ feed ratio of 1. Fresh, spent and regenerated catalysts were characterized by N₂ adsorption for BET surface area determination, XRD, ICP, XPS and TEM. The catalytic activity of the studied Ni-Pd catalysts depends strongly on the support used and decreases in the following ranking: ZrO₂-La₂O₃, La₂O₃ > ZrO₂ > SiO₂ > Al₂O₃ > TiO₂. The bimetallic catalysts were more active than catalysts containing Ni or Pd alone. A Ni to Pd ratio = 4 at a metal loading of 7.5 wt% revealed the best results. Higher loading lead to increased formation of coke; partly in shape of carbon nanotubes (CNT) as identified by TEM. Furthermore, the effect of different calcination temperatures was studied; 600 °C was found to be most favorable. No effect on the catalytic activity was observed if a fresh catalyst was pre-reduced in H₂ prior to use or spent samples were regenerated by air treatment. Ni and Pd metal species are the active components under reaction conditions. Best conversions of CO₂ of 78% and CH₄ of 73% were obtained using a 7.5 wt% NiPd (80:20) ZrO₂-La₂O₃ supported catalyst at a reaction temperature of 700 °C. CO and H₂ yields of 57% and 59%, respectively, were obtained.     

Preparation of Ni/MgO catalyst for CO2 reforming of methane by dielectric-barrier discharge plasma

A novel plasma-treated Ni/MgO catalyst was prepared by treating coprecipitated NiCO₃–MgCO₃ with dielectric-barrier discharge plasma. The results by XRD, TEM and N₂ adsorption analyses showed that the plasma-prepared Ni/MgO catalyst possessed smaller particle size, enhanced nickel dispersion, and higher specific surface area than a conventionally reduced Ni/MgO catalyst. The plasma-prepared Ni/MgO catalyst also exhibited better catalytic activity for carbon dioxide reforming of methane. More than 20% higher conversions of methane and carbon dioxide were obtained than those over the conventional Ni/MgO catalyst at 700 °C and a space velocity of 96,000 mL/(h?g_cat).     

CO2 reforming and partial oxidation of methane

CO₂ reforming and partial oxidation of CH₄ were investigated on different supported noble metal and Ni catalysts. A detailed thermodynamic analysis was performed for both reactions. The observed reaction behaviour can be predicted by thermodynamics. Product selectivity is catalyst independent, the role of the catalyst is to bring the reactants to approach equilibrium. The partial oxidation is a two-stage process, total oxidation of CH₄ is followed by CO₂ and H₂O reforming of the remaining CH₄. A staged addition of O₂ to the reactor is tested and recommended. TPSR show that the catalyst surface for CO₂ reforming was highly covered with carbonaceous species of four different types; two were identified as reactive intermediates.     

Improved resistance against coke deposition of titania supported cobalt and nickel bimetallic catalysts for carbon dioxide reforming of methane

The catalytic behavior of bi-metallic Co–Ni/TiO₂ catalysts for CO₂ reforming of CH₄ to synthesis gas was investigated under atmospheric pressure with a particular attention to carbon deposition. The catalysts with optimized Co/Ni ratios showed high catalytic stability towards the reaction with very little amount of deposited carbon at a wide range of reaction temperature (773–1123 K). The results suggest that adjusting of composition of the active metals (Co and Ni) can kinetically control the elementary steps (formation of carbon species and its removal by oxygen species) of CH₄/CO₂ reaction.     

Integrated coal pyrolysis with CO2 reforming of methane over Ni/MgO catalyst for improving tar yield

A new process to integrate coal pyrolysis with CO₂ reforming of methane over Ni/MgO catalyst was put forward for improving tar yield. And several Chinese coals were used to confirm the validity of the process. The experiments were performed in an atmospheric fixed-bed reactor containing upper catalyst layer and lower coal layer to investigate the effect of pyrolysis temperature, coal properties, Ni loading and reduction temperature of Ni/MgO catalysts on tar, water and char yields and CH₄ conversion at fixed conditions of 400 ml/min CH₄ flow rate, 1:1 CH₄/CO₂ ratio, 30 min holding time. The results indicated that higher tar yield can be obtained in the pyrolysis of all four coals investigated when coal pyrolysis was integrated with CO₂ reforming of methane. For PS coal, the tar, water and char yield is 33.5, 25.8 and 69.5 wt.%, respectively and the CH₄ conversion is 16.8%, at the pyrolysis temperature of 750 °C over 10 wt.% Ni/MgO catalyst reduced at 850 °C. The tar yield is 1.6 and 1.8 times as that in coal pyrolysis under H₂ and N₂, respectively.     

CH4/CD4 isotope effects in the carbon dioxide reforming of methane to syngas over SiO2-supported nickel catalysts

By performing the CH₄ + CO₂ and CD₄ + CO₂ reactions alternately over SiO₂-supported nickel catalysts in a pulse micro-reactor, normal deuterium isotope effects on both the methane conversion reaction and on the CO formation reaction have been observed in the process of CO₂ reforming of methane. Based on the observed CH₄/CD₄ isotope effects, the pathways for the formation of CO are discussed.     

Reactivation and remaking of calcium aluminate pellets for CO2 capture

CaO-based pellets supported with aluminate cements show superior performance in carbonation/calcination cycles for high-temperature CO₂ capture. However, like other CaO-based sorbents, their CO₂ carrying activity is reduced after increasing numbers of cycles under high-temperature, high-CO₂ concentration conditions. In this work the feasibility of their reactivation by steam or water and remaking (reshaping) was investigated. The pellets, prepared from three limestones, Cadomin and Havelock (Canada) and Katowice (Poland, Upper Silesia), were tested in a thermogravimetric analyzer (TGA). The cycles were performed under realistic CO₂ capture conditions, which included calcination in 100% CO₂ at temperatures up to 950 °C. Typically, after 30 cycles, samples were hydrated for 5 min with saturated steam at 100 °C in a laboratory steam reactor (SR). Moreover, larger amounts of pellets were cycled in a tube furnace (TF), hydrated with water and reshaped, and tested to determine their CO₂ capture activity in the TGA. It was found that, after the hydration stage, pellets recovered their activity, and more interestingly, pellets that had experienced a longer series of cycles responded more favorably to reactivation. Moreover, it was found that conversion of pellets increased after about 70 cycles (23%), reaching 33% by about cycle 210, with no reactivation step. Scanning electron microscope (SEM) analyses showed that the morphology of the low-porosity shell formed at the pellet surface during cycles, which limits conversion, was eliminated after a short period (5 min) of steam hydration. The nitrogen physisorption analyses (BET, BJH) of reshaped spent pellets from cycles in the TF confirmed that sorbent surface area and pore size distribution were similar to those of the original pellets. The main alumina compound in remade pellets as determined by XRD was mayenite (Ca₁₂Al₁₄O₃₃). These results showed that, with periodic hydration/remaking steps, pellets can be used for extended times in CO₂ looping cycles, regardless of capture/regeneration conditions.     

Carbon dioxide reforming of methane to synthesis gas over hexaaluminate ANiAl11O19-delta (A = Ca, Sr, Ba and La) catalysts

A series of A‐modified hexaaluminates, ANiAl₁₁O_19-δ (A = Ca, Sr, Ba and La) as new catalysts for carbon dioxide reforming of methane to synthesis gas, were prepared by decomposition of nitrates and calcination at high temperature. Nickel ions as active component were inlayed in the hexaaluminate lattices to substitute part of Al ions. The structure and properties of these samples were characterized using XRD, XPS, TPR and TGA techniques. The series of hexaaluminates exhibited significantly catalytic activity and stability at high temperature, for instance at 780°C for 18 h, the conversion of CH₄ and CO₂ was kept over 91.0 and 93.7%, respectively, meanwhile no Ni sintering, phase transformation and catalyst deactivation due to carbon deposition were found. Besides, the modifier A in the mirror plane layer of the lattices showed different effects on reducibility and catalytic activity of transition metal Ni in the hexaaluminate lattices. This revised version was published online in July 2006 with corrections to the Cover Date.     

Effect of particle shape on fluid flow and heat transfer for methane steam reforming reactions in a packed bed

Numerical simulations of a cylindrical packed bed with tube to particle diameter ratio of 1.4, containing 10 particles, were performed to understand the effect of particle shape on pressure drop, heat transfer and reaction performance. Six particle shapes namely, cylinder as the reference, trilobe and daisy having external shaping, hollow cylinder, cylcut, and 7‐hole cylinder including internal voids were chosen. Methane steam reforming reactions were considered for the heat transfer and reaction performance evaluation. The present study showed that the external shaping of particles offered lower pressure drop, but lower values of effectiveness factor indicating strong diffusion limitations. The internally shaped particles offered increased surface area, led to higher effectiveness factor and allowed to overcome the diffusion limitations. The effective heat transfer and effectiveness factor of the trilobe‐shaped particle per unit pressure drop was found to be the best among the particle shapes considered in the present work. © 2016 American Institute of Chemical Engineers AIChE J, 63: 366–377, 2017     

Influence of molybdenum and tungsten additives on the properties of nickel steam reforming catalysts

An introduction of small amounts of molybdenum and tungsten compounds into the nickel catalyst of the steam reforming of methane considerably reduces the detrimental effect of carbon deposit formation, while entailing no change in the catalyst activity.