Fractal study of LiMn2O4 film electrode surface for lithium batteries application

Fractal structure of a LiMn₂O₄ film electrode has been investigated and its fractal dimensions was determined using different electrochemical techniques, viz. cyclic voltammetry and chronoamperometry. The results obtained from both these methods are in good agreement indicating the reliability of the estimated D_f. The fractal study of the LiMn₂O₄ film electrode suggests a complex surface with high fractal dimension. In addition, length scales of the electrode surface were also calculated.     

Theoretical approach to cell-impedance-controlled lithium transport through Li1 − δMn2O4 film electrode with partially inactive fractal surface by analyses of potentiostatic current transient and linear sweep voltammogram

Lithium transport through the partially inactive fractal Li_1 − δMn₂O₄ film electrode under the cell-impedance-controlled constraint was theoretically investigated by using the kinetic Monte Carlo method based upon random walk approach. Under the cell-impedance-controlled constraint, all the potentiostatic current transients calculated from the totally active and partially inactive fractal electrodes hardly exhibited the generalised Cottrell behaviour and they were significantly affected in shape by the interfacial charge-transfer kinetics. In the case of the linear sweep voltammogram determined from the totally active and partially inactive fractal electrodes, all the power dependence of the peak current on the scan rate above the characteristic scan rate deviated from the generalised Randles-Sev?ik behaviour. From the analyses of the current transients and the linear sweep voltammograms simulated with various values of the simulation parameters, it was further recognised that the cell-impedance-controlled lithium transport through the partially inactive fractal Li_1 − δMn₂O₄ film electrode strongly deviates from the generalised diffusion-controlled transport behaviour of the electrode with the totally active surface, which is attributed to the impeded interfacial charge-transfer kinetics governed by the surface inhomogeneities including the fractal dimension of the surface and the surface coverage by active sites and by the kinetic parameters including the internal cell resistance.     

The cell-impedance-controlled lithium transport through LiMn2O4 film electrode with fractal surface by analyses of ac-impedance spectra, potentiostatic current transient and linear sweep voltammogram

Lithium transport through the fractal LiMn₂O₄ film electrode under the cell-impedance-controlled constraint was investigated by employing ac-impedance spectroscopy, potentiostatic current transient technique and linear sweep voltammetry. For this purpose, the flat and fractal LiMn₂O₄ film electrodes were prepared on the as-deposited Pt/polished Al₂O₃ substrate and the surface modified Pt/unpolished Al₂O₃ substrate, respectively. From the analysis of the ac-impedance spectra obtained from the flat and fractal electrodes, it is found that the apparent self-similar fractal dimension reduces the charge-transfer resistance, and the phase angle of the diffusion impedance under the semi-infinite diffusion condition positively deviates in absolute value from 45° with increasing fractal dimension. All the potentiostatic current transients experimentally measured from the flat and fractal LiMn₂O₄ electrodes showed non-generalised Cottrell behaviour which resulted from the cell-impedance-controlled constraint during lithium transport. In the case of linear sweep voltammogram theoretically calculated and experimentally measured from the flat and fractal LiMn₂O₄ electrodes, the power dependence of the peak current on the scan rate hardly exhibited the generalised Randles-Sev?ik behaviour. From the analyses of the potentiostatic current transients and the linear sweep voltammograms, furthermore, it is experimentally confirmed that the internal cell resistance mainly determining the cell-impedance-controlled lithium transport strongly depends upon the fractal dimension as well as such external parameters as the applied potential step and the amount of lithium transferred during lithium transport.     

Investigation of hydrogen transport through Mm(Ni3.6Co0.7Mn0.4Al0.3)1.12 and Zr0.65Ti0.35Ni1.2V0.4Mn0.4 hydride electrodes by analysis of anodic current transient

Hydrogen transport through such metal-hydride electrodes as Mm(Ni_3.6Co_0.7Mn_0.4Al_0.3)_1.12 and Zr_0.65Ti_0.35Ni_1.2V_0.4Mn_0.4 was investigated in 6 M KOH solution by using potentiostatic current transient technique. From the shape of the anodic current transient and the dependence of the initial current density on the discharging potential, the boundary conditions at the electrode surface were established during hydrogen extraction from the as-annealed and as-surface-treated electrodes. Especially, it was experimentally confirmed that the diffusion-limited boundary condition is no longer valid at the electrode surface during hydrogen transport in case hydrogen diffusion is coupled with either the interfacial charge transfer reaction or the hydrogen transfer reaction between adsorbed state on the electrode surface and absorbed state at the electrode sub-surface. From the transition behaviour of the boundary condition, it was further recognised that the boundary condition at the electrode surface during hydrogen transport is not fixed at the specific electrode/electrolyte system by itself, but it is rather simultaneously determined even at any electrode/electrolyte system by the potential step and the nature of the electrode surface, depending upon e.g. the presence or absence of the surface oxide scales.     

Cycling-induced stress in lithium ion negative electrodes: LiAl/LiFePO4 and Li4Ti5O12/LiFePO4 cells

In this work, we examined the electrochemical behaviour of lithium ion batteries containing lithium iron phosphate as the positive electrode and systems based on Li-Al or Li-Ti-O as the negative electrode. These two systems differ in their potential versus the redox couple Li⁺/Li and in their morphological changes upon lithium insertion/deinsertion. Under relatively slow charge/discharge regimes, the lithium-aluminium alloys were found to deliver energies as high as 438 Wh kg⁻¹ but could withstand only a few cycles before crumbling, which precludes their use as negative electrodes. Negative electrodes consisting solely of aluminium performed even worse. However, an electrode made from a material with zero-strain associated to lithium introduction/removal such as a lithium titanate spinel exhibited good performance that was slightly dependent on the current rate used. The Li₄Ti₅O₁₂/LiFePO₄ cell provided capacities as high as 150 mAh g⁻¹ under C-rate in the 100th cycle.     

Mechanism transition of cell-impedance-controlled lithium transport through Li1−δMn2O4 composite electrode caused by surface-modification and temperature variation

The mechanism transition of lithium transport through a Li_1−δMn₂O₄ composite electrode caused by the surface-modification and temperature variation was investigated using the galvanostatic intermittent titration technique (GITT), electrochemical impedance spectroscopy (EIS) and the potentiostatic current transient technique. From the analyses of the ac-impedance spectra, experimentally measured from unmodified Li_1−δMn₂O₄ and surface-modified Li_1−δMn₂O₄ with MgO composite electrodes, the internal cell resistance of the MgO-modified Li_1−δMn₂O₄ electrode was determined to be much smaller in value than that of the unmodified electrode over the whole potential range. Moreover, from the analysis of the anodic current transients measured on the MgO-modified Li_1−δMn₂O₄ electrode, it was found that the cell-impedance-controlled constraint at the electrode surface is changed to a diffusion-controlled constraint, which is characterised by a large potential step and simultaneously by a small amount of lithium transferred during lithium transport. This strongly suggests that the internal cell resistance plays a significant role in determining the cell-impedance-controlled lithium transport through the MgO-modified Li_1−δMn₂O₄ electrode. Furthermore, from the temperature dependence of the internal cell resistance and diffusion resistance in the unmodified Li_1−δMn₂O₄ composite electrode measured by GITT and EIS, it was concluded that which mechanism of lithium transport will be operative strongly depends on the diffusion resistance as well as on the internal cell resistance.     

Fabrication of carbon paste electrode containing [PFeW11O39] polyoxoanion supported on modified amorphous silica gel and its electrocatalytic activity for H2O2 reduction

[PFeW₁₁O₃₉]⁴⁻ (PFeW₁₁) supported on the surface of 3-aminopropyl(triethoxy)silane modified silica gel was synthesized and used as a bulk modifier to fabricate a renewable three-dimensional chemically modified electrode. The electrochemical behavior of the modified electrode was investigated. Cyclic voltammetry studies showed that the PFeW₁₁ on the electrode surface sustained the same electrochemical properties as that of the PFeW₁₁ in solution. The preparation of chemically modified electrode is simple and quiet reproducible using inexpensive material. The modified electrode had high electrocatalytic activity toward H₂O₂ reduction and it was successfully applied as an electrochemical detector to monitor H₂O₂ in flow injection analysis (FIA). The electrocatalytic peak current was found to be linear with the H₂O₂ concentration in the range 10-200 μmol L⁻¹ with a correlation coefficient of 0.998 and a detection limit (3σ) of 7.4 μmol L⁻¹ H₂O₂. The electrode has the remarkable advantage of surface renewal owing to bulk modification, as well as simple preparation, good mechanical and chemical stability and reproducibility.     

Modeling the impedance versus voltage characteristics of LiNi0.8Co0.15Al0.05O2

The power-delivery capability of lithium-ion cells based on LiNi_0.8Co_0.15Al_0.05O₂-based positive electrodes shows a significant dependence on the cell's state-of-charge. One reason for this behavior is the variation of the positive electrode's impedance with the oxide's lithium content. In this article, an electrochemical model based on concentrated solution porous electrode theory is used to model impedance data obtained on LiNi_0.8Co_0.15Al_0.05O₂-based positive electrodes charged to potentials ranging from 3.55 to 4.55 V versus Li. The parameters obtained from model fits include the exchange-current density and Li-ion diffusion coefficients in the oxide. The variations in these parameters with oxide potential are correlated with structural changes in the material observed during Li-ion intercalation-deintercalation reactions.     

Optimization of microwave synthesis of Li[Ni0.4Co0.2Mn0.4]O2 as a positive electrode material for lithium batteries

A positive electrode material for lithium ion battery applications was successfully synthesized using microwave irradiation. This microwave synthesis has several merits such as homogeneity of final product and much shorter reaction time compared to conventional synthetic methods. We synthesized spherical [Ni_0.4Co_0.2Mn_0.4](OH)₂ as a precursor by a co-precipitation method. The pelletized mixture of the precursor and lithium hydroxide was calcined under different reaction times and temperatures by applying 1200 W of microwave irradiation at 2.45 GHz. We determined the optimum conditions of microwave synthesis for positive electrode materials. The powders were characterized by X-ray diffraction, scanning electron microscopy, and electrochemical testing. The capacity, its retention, and thermal stability of Li[Ni_0.4Co_0.2Mn_0.4]O₂ synthesized by the microwave synthesis were comparable to the Li[Ni_0.4Co_0.2Mn_0.4]O₂ prepared by the high temperature calcination method.     

Composite Ni/Al2O3 coatings and their corrosion resistance

Composite coatings Ni/Al₂O₃ were electrochemically deposited from a Watts bath. Al₂O₃ powder with particle diameter below 1 μm was codeposited with the metal. The obtained Ni/Al₂O₃ coatings contained 5-6% by weight of corundum. The structure of the coatings was examined by scanning electron microscopy (SEM). It has been found that the codeposition of Al₂O₃ particles with nickel disturbs the nickel coating's regular surface structure, increasing its microcrystallinity and surface roughness. DC and AC electrochemical tests were carried out on such coatings in a 0.5 M solution of Na₂SO₄ in order to evaluate their corrosion resistance. The potentiodynamic tests showed that the corrosion resistance of composite coating Ni/Al₂O₃ is better than that of the standard nickel coating. After 14 days of exposure the nickel coating corrodes three times faster than the Ni/Al₂O₃ coating. The electrochemical behaviour of the coatings in the corrosive solution was investigated by electrochemical impedance spectroscopy (EIS). An equivalent circuit diagram consisting of two RC electric circuits: one for electrode, nickel corrosion processes and the other for processes causing coating surface blockage, were adopted for the analysis of the impedance spectra. The changes in the charge transfer resistance determined from the impedance measurements are comparable with the changes in corrosion resistance determined from potentiodynamic measurements.     

One-step electrodeposition synthesis and electrochemical properties of Cu6Sn5 alloy anodes for lithium-ion batteries

Cu₆Sn₅ alloys were successfully electrodeposited on rough Cu foils and smooth Cu sheets using a facile one-step electrodepositing method, and their structural and electrochemical properties were examined by X-ray diffraction (XRD), scanning electron microscopy (SEM), galvanostatic charging/discharging testing and electrochemical impedance spectroscopy (EIS). The influence of surface morphology of the current collectors on the cycleability and the interfacial performance of the Cu₆Sn₅ alloy electrode are both discussed. The results demonstrate that the Cu₆Sn₅ alloy electrode on the rough Cu foil presented better electrochemical performance than that on the smooth Cu sheet because its rough surface could buffer the volume changes to some extent. The first discharging (lithiation) and charging (delithiation) capacities were measured at 462 and 405 mAh g⁻¹ respectively with high initial coulomb efficiency of 88%, with charging capacity in the 50th cycle remaining 76% of that in the first cycle. The phase transformation during initial lithiation was detected by electrochemical impedance spectroscopy (EIS) and its trend versus electrode potential is also discussed.     

Structure and electrochemical properties of nanocarbon-coated Li3V2(PO4)3 prepared by sol-gel method

A liquid-based sol-gel method was developed to synthesize nanocarbon-coated Li₃V₂(PO₄)₃. The products were characterized by XRD, SEM and electrochemical measurements. The results of Rietveld refinement analysis indicate that single-phase Li₃V₂(PO₄)₃ with monoclinic structure can be obtained in our experimental process. The discharge capacity of carbon-coated Li₃V₂(PO₄)₃ was 152.6 mAh/g at the 50th cycle under 1C rate, with 95.4% retention rate of initial capacity. A high discharge capacity of 184.1 mAh/g can be obtained under 0.12C rate, and a capacity of 140.0 mAh/g can still be held at 3C rate. The cyclic voltammetric measurements indicate that the electrode reaction reversibility is enhanced due to the carbon-coating. SEM images show that the reduced particle size and well-dispersed carbon-coating can be responsible for the good electrochemical performance obtained in our experiments.     

Aging characteristics of high-power lithium-ion cells with LiNi0.8Co0.15Al0.05O2 and Li4/3Ti5/3O4 electrodes

The impedance rise that results from the accelerated aging of high-power lithium-ion cells containing LiNi_0.8Co_0.15Al_0.05O₂-based positive and graphite-based negative electrodes is dominated by contributions from the positive electrode. Data from various diagnostic experiments have indicated that a general degradation of the ionic pathway, apparently caused by surface film formation on the oxide particles, produces the positive electrode interface rise. One mechanistic hypothesis postulates that these surface films are components of the negative electrode solid electrolyte interphase (SEI) layer that migrate through the electrolyte and separator and subsequently coat the positive electrode. This hypothesis is examined in this article by subjecting cells with LiNi_0.8Co_0.15Al_0.05O₂-based positive and Li_4/3Ti_5/3O₄-based negative electrodes to accelerated aging. The impedance rise in these cells was observed to be almost entirely from the positive electrode. Because reduction products are not expected on the 1.55 V Li_4/3Ti_5/3O₄ electrode, the positive electrode impedance cannot be attributed to the migration of SEI-type fragments from the negative electrode. It follows then that the impedance rise results from mechanisms that are “intrinsic” to the positive electrode.     

Mixed oxides Ca2Fe2O5 and Ca2Co2O5 as anode materials for Li-ion batteries

The electrochemical performance of mixed oxides, Ca₂Fe₂O₅ and Ca₂Co₂O₅ for use in Li-ion batteries was studied with Li as the counter electrode. The compounds were prepared and characterized by X-ray diffraction and SEM. Ca₂Fe₂O₅ showed a reversible capacity of 226 mAh/g at the 14th cycle and retained 183 mAh/g at the end of 50 cycles at 60 mA/g in the voltage window 0.005-2.5 V. A reversible capacity in the range, 365-380 mAh/g, which is stable up to 50 charge-discharge cycles is exhibited by Ca₂Co₂O₅ in the voltage window, 0.005-3.0 V and at 60 mA/g. This corresponds to recycleable moles of Li of 3.9±0.1 (theoretical: 4.0). Significant improvement in the cycling performance and attainable reversible capacity were noted for Ca₂Co₂O₅ on cycling to an upper cut-off voltage of 3.0 V as compared to 2.5 V. Coulombic efficiency for both compounds is >98%. Electrochemical impedance spectroscopy (EIS) data clearly indicate the reversible formation/decomposition of polymeric surface film on the electrode surface of Ca₂Co₂O₅ in the voltage window, 0.005-3.0 V. Cyclic voltammetry results compliment the galvanostatic cycling data.     

Effect of TiO2 doped Ni electrodes on the dielectric properties and microstructures of (Ba0.96Ca0.04)(Ti0.85Zr0.15)O3 multilayer ceramic capacitors

The effects of TiO₂-doped Ni electrodes on the microstructures and dielectric properties of (Ba_0.96Ca_0.04)(Ti_0.85Zr_0.15)O₃ multilayer ceramic capacitors (MLCCs) have been investigated. Nickel paste with a TiO₂ dopant was used as internal electrodes in MLCCs based on (Ba_0.96Ca_0.04)(Ti_0.85Zr_0.15)O₃ (BCTZ) ceramic with copper end-termination. The microstructures and defects were analysed by microstructural techniques (SEM/HRTEM) and energy-dispersive spectroscopy (EDS). The continuity of the electrode of the MLCC was measured using a scanning electron microscope, which showed that the continuity of the electrode for the MLCC with a TiO₂-doped Ni electrode was approximately 90%. However, continuity of the electrode for a conventional MLCC was below 80%. The continuity of the TiO₂-doped Ni electrode showed significant improvement in the MLCC, which was due to no reaction between Ni and BCTZ.     

Preparation and characterization of Bi2Se3 nanowires by electrodeposition

The electrodeposition of Bi₂Se₃ nanowires on an anodic aluminum oxide template was investigated by cyclic voltammetry in a tartaric acid aqueous solution. The electrochemical behavior of the Bi₂Se₃ nanowires in the electrolytic solution was also investigated using cyclic voltammetry, and the underpotential deposition mechanism of the Bi₂Se₃ nanowires was determined. According to the cyclic voltammetric curves, −0.20 V vs. SCE (saturated calomel electrode) was chosen as the deposition potential of the Bi₂Se₃ nanowires. The ratio of Bi to Se is nearly 2:3, verified by energy-dispersive X-ray spectroscopy and with the addition of surfactant. X-ray diffraction, scanning electron microscopy, selected-area electron diffraction and high-resolution transmission electron microscopy indicate that annealing can improve the crystallinity and chemical composition of Bi₂Se₃ nanowires. Surfactant can also improve the surface morphology and composition of the Bi₂Se₃ nanowires.     

Electrochemical investigation of LiNi0.5Mn1.5O4 thin film intercalation electrodes

This work provides kinetic and transport parameters of Li-ion during its extraction/insertion into thin film LiNi_0.5Mn_1.5O₄ free of binder and conductive additive. Thin films of LiNi_0.5Mn_1.5O₄ (0.2 μm thick) were prepared on electronically conductive gold substrate utilizing the electrostatic spray deposition technique. High purity LiNi_0.5Mn_1.5O₄ thin film electrodes were observed with cyclic voltammetry, to exhibit very sharp peaks, high reversibility, and absence of the 4 V signal related to the Mn³⁺/Mn⁴⁺ redox couple. The electrode subjected to 100 CV cycles of charge/discharge delivered a capacity of 155 mAh g⁻¹ on the first cycle and sustained a good cycling behavior while retaining 91% of the initial capacity after 50 cycles. Kinetics and mass-transport of Li-ion extraction at LiNi_0.5Mn_1.5O₄ thin film electrode were investigated by means of electrochemical impedance spectroscopy. The apparent chemical diffusion coefficient (D_app) value determined from EIS measurements changed depending on the electrode potential in the range of 10⁻¹⁰-10⁻¹² cm² s⁻¹. The D_app profile shows two minimums at the potential values close to the peak potentials of the corresponding cyclic voltammogram.     

LiNi0.1Mn0.1Co0.8O2 electrode material: Structural changes upon lithium electrochemical extraction

We reported here on the synthesis, the crystal structure and the study of the structural changes during the electrochemical cycling of layered LiNi_0.1Mn_0.1Co_0.8O₂ positive electrode material. Rietveld refinement analysis shows that this material exhibits almost an ideal α-NaFeO₂ structure with practically no lithium-nickel disorder. The SQUID measurements confirm this structural result and evidenced that this material consists of Ni²⁺, Mn⁴⁺ and Co³⁺ ions.Unlike LiNiO₂ and LiCoO₂ conventional electrode materials, there was no structural modification upon lithium removal in the whole 0.42 ≤ x ≤1.0 studied composition range. The peaks revealed in the incremental capacity curve were attributed to the successive oxidation of Ni²⁺ and Co³⁺ while Mn⁴⁺ remains electrochemically inactive.     

On the LiCo2/3Ni1/6Mn1/6O2 positive electrode material

LiCo_2/3Ni_1/6Mn_1/6O₂ layered oxide was synthesized by the combustion method that led to a crystalline phase with good homogeneity and low particles size. The structural properties of the prepared positive electrode material were investigated by performing XRD Rietveld refinement. Practically no Li/Ni mixing was detected evidencing that the studied compound adopts almost an ideal α-NaFeO₂ type structure. The Li||LiCo_2/3Ni_1/6Mn_1/6O₂ cell showed a discharge capacity of 199 mAh g⁻¹ when cycled in the 2.7–4.6 V potential range while the best cycling performances were recorded when the upper cut off is fixed at 4.5 V. Structural changes in Li_xCo_2/3Ni_1/6Mn_1/6O₂ with lithium electrochemical de-intercalation were studied using X-ray diffraction. This study clearly shows the existence of a solid solution domain in the 0.1 < x < 1.0 composition range while for x = 0.1, a new phase appears explaining the decrease of the electrochemical performance when the cell is cycled at high upper cut off voltage.     

Preparation of micro-dot electrodes of LiCoO2 and Li4Ti5O12 for lithium micro-batteries

Fabrications of micro-dot electrodes of LiCoO₂ and Li₄Ti₅O₁₂ on Au substrates were demonstrated using a sol-gel process combined with a micro-injection technology. A typical size of prepared dots was about 100 μm in diameter, and the dot population on the substrate was 2400 dots cm⁻². The prepared LiCoO₂ and Li₄Ti₅O₁₂ micro-dot electrodes were characterized with scanning electron microscopy, X-ray diffraction, micro-Raman spectroscopy, and cyclic voltammetry. The prepared LiCoO₂ and Li₄Ti₅O₁₂ micro-dot electrodes were evaluated in an organic electrolyte as cathode and anode for lithium micro-battery, respectively. The LiCoO₂ micro-dot electrode exhibited reversible electrochemical behavior in a potential range from 3.8 to 4.2 V versus Li/Li⁺, and the Li₄Ti₅O₁₂ micro-dot electrode showed sharp redox peaks at 1.5 V.