水平窄空间沸腾换热的数理模型研究

窄空间只有在间距小于汽泡脱离直径时,对沸腾传热强化才有比较显的效果。窄空间沸腾强化传热的机理在于较大的泡底微层加速了蒸发传热和窄空间中被加热的液体周期性地与池液进行容积交换。水平圆盘窄空间中的汽泡生长分为性质完全不同的自由生长期和抑制长大期;在一个周期内,加热面的总传热量等于壁面传导给窄空间液体的热量与通过合体泡底微层蒸发潜热之和。在对圆形水平窄空间的沸腾传热的现象和机理进行分析的基础上,提出了窄空间的沸腾换热过程的数理模型;进而对窄空间沸腾的本质规律在理论上进行了初步探索,并得到分析解。理论计算结果与实验数据比较表明,该分析解适合于中低壁面过热度的情形。由于问题的复杂性,该模型仍需不断完善。     

水平管束沸腾传热增强的研究

本文分别以单组份和双组份为沸腾工质,对水平管束的沸腾传热进行了研宄,并提出了从水平管束底部引入惰性气体的方法,研究了由此引起的传热增强。实验结果表明引入惰气使传热膜系数得到很大的提高,作者对此传热增强的机理进行了分析。     

竖直矩形窄缝两相同向分相流动沸腾传热模型

首次对竖直矩形窄缝内的汽液分相流动区提出一维两相同向分相流动沸腾传热模型 ,并进行了数值计算 ,得到不同质量流速下液膜厚度变化和沸腾传热系数等结果。沸腾传热系数的模型预测值初步与已有实验关联式进行了比较 ,两者基本吻合 ,偏差在± 1 4% ;从而证实了液膜导热是竖直矩形窄缝内汽液分相流动区沸腾传热的主导机理。     

单面加热竖直窄通道内环状流沸腾传热特性

基于汽芯的动量方程和液膜的质量和动量方程,建立了单面均匀热流竖直窄通道内环状流沸腾传热模型,利用数值法对方程组进行求解,得出了环状流区域的液膜厚度,并进一步预测了环状流两相沸腾传热系数。研究表明:模型预测的两相沸腾传热系数比Mahmound关联式计算值偏小;将不同工况下的291组环状流两相沸腾传热系数实验值与模型预测值进行对比,平均绝对误差为12.7%。     

窄通道内流动沸腾强化换热研究进展

窄通道具有结构紧凑、传热效率高等优点.随着科技发展,窄通道已经成为强化换热的常用结构形式之一,被广泛应用于各种换热设备.由于窄通道内间隙内气泡的尺寸受限,气泡在发展过程中会受到挤压而发生变形,带走大量的潜热,引起汽液界面的扰动,换热性能较常规通道有很大区别.本文综述了窄通道内的主要流型及转变准则;介绍了几何与工况参数变化对窄通道内换热效果影响的传热实验研究;分析了窄通道中传热机理以及两相摩擦压降机理,并对关联式进行了总结与评述;对窄通道内强化换热的机理与进一步强化换热的方法进行归纳总结;结合目前实验与理论研究总结了现存问题,为窄通道内流动沸腾强化换热的进一步研究提供了参考.     

强润湿性液体池沸腾传热的实验研究和机理分析

对强润湿性液体的池沸腾传热实验而言,本文提出了行之有效的实验程序,并严格按照实验程序进行了R113池沸腾传热的实验研究,具体研究了表现老化和液体过冷度对池沸腾传热曲线及起沸点的影响,实验中观察到了三个反常现象,最后,从强润湿性液体的沸腾传热机理的角度对其给出了相应的解释。     

多孔表面强化沸腾传热的研究

一、前言 当前全世界普遍重视节省能源,降低产品能耗已成为重要的研究课题。构成节能对象的机器设备中,有众多的热交换器,因此,研究提高现有传热设备的性能和探求新的强化方法,对于降低能耗具有重要意义。     

垂直矩形窄通道流动沸腾换热特性实验研究

流动沸腾换热是典型的两相流问题。窄通道与常规通道相比较,其流动沸腾换热系数有较大提高,换热机理也更加复杂。针对截面为250 mm×5 mm的竖直矩形窄缝通道,在低压、入口温度过冷、不同质量流速及加热功率密度的条件下,对水流动沸腾换热特性进行实验研究。通过实验分析可知:入口温度27～60℃、质量流速2.22～3.49 kg/(m2.s)及加热功率密度0～12 kW/m2对饱和沸腾起始点和过冷段长度有重要影响;高的空泡份额和通道结构的限制使汽液两相流动不稳定而影响换热系数,换热系数随着功率的增大而减小,流体进入完全对流沸腾阶段;由于实验段通道顶部结构的限制,干度的增加不会出现干涸点,换热不会得到恶化,换热系数随着功率的增大基本不变。     

多孔表面新型复杂结构优化沸腾传热的实验研究

报道了R11在烧结多孔表面开槽时沸腾传热的实验研究,实验发现,与普通槽道和双空隙层多孔表面相比,沸腾换热增强,沸腾表现为液体灌注、槽道起泡、底部蒸干三个区,对特定的多孔层,开槽可获得更好的换热效果。带槽道的多孔表面实验件与均匀多孔表面相比,在相同壁面过热度（θ）条件下,热流密度（q）提高2－10倍,临界热流密度提高2－4倍。     

多孔表面管沸腾传热试验研究

针对烧制成多孔表面管,进行了传热性能研究,试验表明：多孔管可以显著地强化多孔侧沸腾传热,民同规格光滑管传热性能试验对比,其沸腾给热系数比光滑管提高５－６倍。     

Experimental research of pool boiling heat transfer in horizontal narrow spaces

Much progress has been made in high‐performance electronic chips, the miniaturization of electronic circuits and other compact systems recently, which brings about a great demand for developing efficient heat removal techniques to accommodate these high heat fluxes. With this objective in mind, experiments were carried out on five kinds of test elements with distilled water and ethanol as working liquids. The test elements used in these experiments consisted of five parallel discs with diameters varying from 5 mm to 40 mm. The experiments were performed with the discs oriented horizontally and uniform heat fluxes applied at the bottom surfaces. The influence of narrow spacing, space size, working liquid property, and heat flux on boiling heat transfer performance in narrow spaces has been investigated. Experimental results showed that the boiling heat transfer coefficient of a narrow space was 3 to 6 times higher than that of pool boiling when the narrow space size and heat flux combine adequately, but the critical heat flux was lower than that of pool boiling. © 2004 Wiley Periodicals, Inc. Heat Trans Asian Res, 33(5): 307–315, 2004; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20017     

Enhancement of boiling heat transfer in restricted spaces in compact horizontal tube bundles

ln desalinization devices and some heat exchangers making use of low‐quality heat energy, both wall temperatures and heat fluxes of heated tubes are quite low and generally cannot cause boiling in flooded‐type tube bundle evaporators with a large tube spacing. But when the tube spacing is very small, boiling in restricted spaces can occur and induce a higher heat transfer than that of a falling film or pool boiling at the same heat flux. This study investigated experimentally the effects of tube spacing, positions of tubes, and heating status of tubes as well as surface status (smooth and roll‐worked) on boiling in restricted spaces in compact horizontal tube bundle evaporators under atmospheric pressure. The experimental results provide a restricted space boiling database for water in smooth and enhanced surface tube bundles. Of particular importance is information concerning the influence of tube spacing of flooded‐type tube bundle evaporators, especially for the case of zero pitch, when the neighboring tubes are contacting each other. © 2001 Scripta Technica, Heat Trans Asian Res, 30(5): 394–401, 2001     

Experimental study of pool boiling heat transfer of water‐based magnetic fluid on a horizontal heater

The effect of mass concentration of magnetic particles and an applied magnetic field on pool boiling heat transfer of water‐based magnetic fluid on a horizontal heater was investigated. The experimental results show that high‐concentration magnetic fluid deteriorates boiling heat transfer, while middle‐ and low‐concentration magnetic fluid enhances the boiling heat transfer. There was an optimum concentration in which the enhancement of boiling heat transfer was the best. Conclusions were the same with an applied magnetic field that enhances the boiling heat transfer of magnetic fluid further. © 2005 Wiley Periodicals, Inc. Heat Trans Asian Res, 34(3): 180–187, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20054     

垂直矩形窄缝内的过冷流动沸腾换热性能

用高速摄像等方法研究了有压模化介质在单一垂直矩形窄缝流道内的气泡形态和传热情况 ,发现窄缝流动沸腾换热强化的原因在于流道尺寸较小 ,气泡的形状发生变化 ,增加了界面体积浓度 ,并强化了对加热面附近的扰动 ,使换热有所强化。通过与实际测量的壁温数据进行比较 ,发现用于计算大流道和池过冷沸腾换热的 Rohsenow关系式预测窄流道内高热流密度下的过冷流动沸腾换热的误差不大 ,但对于较低热流密度下的过冷流动沸腾时误差较大 ;通过最小二乘法对 Rohsenow关系式进行修正后 ,误差低于± 2 5 %。     

Nucleate Pool Boiling Heat Transfer of Pure Refrigerants and Binary Mixtures

Heat transfer coefficients in nucleate boiling on a smooth flat surface were measured for pure fluids of R-134a, propane, isobutane and their binary mixtures at different pressure from 0.1 to 0.6 MPa. Series of experiments with different heat flux and mixture concentrations were carried out. The influences of pressure and heat flux on the heat transfer coefficient for different pure fluids were studied. Isobutane and propane were used to make up binary mixtures. Compared to the pure components, binary mixtures show lower heat transfer coefficients. This reduction was more pronounced as the heat flux increasing. Several heat transfer correlations are obtained for different pure refrigerants and their binary mixtures.     

Characteristics of heat transfer coefficients during nucleate pool boiling of binary mixtures

Experimental studies were made on heat transfer on a horizontal platinum wire during nucleate pool boiling in nonazeotropic refrigerant binary mixtures at pressures of 0.25 to 0.7 MPa and at heat fluxes up to CHF. The boiling features of the mixtures and the single-component substances were observed by photography. The relationship between the boiling behavior and the reduction of heat transfer coefficients in binary mixtures is discussed in order to propose a correlation useful for predicting the present experimental data over a wide range of low to high heat fluxes. It is shown that the correlation is applicable to alcoholic mixtures. The physical meaning of k, which was introduced to evaluate the effect of heat flux on the reduction of a heat transfer coefficient, is clarified based on measured nucleate pool boiling heat transfer data and visual observations of the boiling features. © 1998 Scripta Technica, Heat Trans Jpn Res, 27(7): 535–549, 1998     

Bubble behavior and heat transfer during pool boiling of binary mixtures

Heat transfer coefficients were measured during pool boiling of binary mixtures on a heated wire hung horizontally and bubble behavior was simultaneously captured with a high‐speed video camera. The experiment was carried out at a pressure of 0.4 and 0.7 MPa for the whole range of mass fractions in a binary mixture of R22/R11. We clarified the change in bubble behavior and heat transfer by measuring the bubble departure diameter, frequency and growth rate on the basis of the video images. Furthermore, we discussed the relationship between the bubble behavior and the boiling heat transfer coefficient in the binary mixtures. © 2005 Wiley Periodicals, Inc. Heat Trans Asian Res, 34(7): 449–459, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20087     

常压下狭缝流动沸腾传热的研究

以蒸馏水为工质，在常压下，对间隙为1mm的环形狭缝通道中的流动传热进行了实验研究。分别将狭缝通道中的单相强制对流和过冷沸腾的实验数据与传统的Dittus-Boelter型关系式的计算结果进行了比较。通过分析狭缝通道中流动沸腾的传热特性认为，过冷沸腾传热比单相强制对流传热加强；质量流速对狭缝通道中的流动沸腾传热有较大影响。