Achieving standard wide color gamut by tuning LED backlight and color filter spectrum in LCD

In order to achieve the standard red, green, and blue (sRGB) standard color gamut in color liquid crystal display and improve the image quality, the impact of the backlight and color filter spectrum on module's chroma was simulated and analyzed. The color gamut was enhanced by adjusting and optimizing the two parts of spectrums of LED backlight and color filter and by using red and green phosphor LED backlight to match the new color filter with an appropriate thickness. Experimental results show that: When the thickness of color filter is 2.2 µm, National Television System Committee color gamut increases from 65.3% to 74.9%, and sRGB matching rate enhances from 83.2% to 100%, achieving a full coverage of the sRGB standard color gamut, the transmittance of white light reaches 28.1%. Also, it is verified that shifting the peak position of the backlight and color filter spectrum to purification direction, as well as narrowing its half‐width can upgrade the color gamut. Meanwhile, the thicker the thickness of color filter is, the wider color gamut it has, based on the same pigment material.     

LED‐backlight feedback control system with integrated amorphous‐silicon color sensor on an LCD panel

Abstract— Thin‐film‐transistor liquid‐crystal displays (TFT‐LCDs) have the largest market share of all digital flat‐panel displays. An LCD backlighting system employing a three‐color red‐green‐blue light‐emitting diode (RGB‐LED) array is very attractive, considering its wide color gamut, tunable white point, high dimming ratio, long lifetime, and environmental compatibility. But the high‐intensity LED has problems with thermal stability and degradation of brightness over time. Color and white luminance levels are not stable over a wide range of temperature due to inherent long‐term aging characteristics. In order to minimize color point and brightness differences over time, optical feedback control is the key technology for any LED‐backlight system. In this paper, the feasibility of an optical color‐sensing feedback system for an LED backlight by integrating the amorphous‐silicon (a‐Si) color sensor onto the LCD panel will be presented. To minimize the photoconductivity degradation of a‐Si, a new laser exposure treatment has been applied. The integrated color‐sensor optical‐feedback‐controlled LED‐backlight system minimized the color variation to less than 0.008 Δu'v' (CIE1976) compared to 0.025 for an open‐loop system over the temperature range of 42–76°C.     

LED backlighting for LCD HDTV

Light‐emitting diodes (LEDs) are used today for backlighting of small displays such as PDAs and mobile phones. We show in this paper that a new LED technology can be used for high‐demanding display‐backlighting applications such as LCD HDTV. Using this new type of emitter, called a Luxeon? Power Light Source, a brightness higher than an edge‐lit CCFL backlight can be achieved, while compared to a direct‐lit CCFL backlight the thickness is lower and the uniformity is better. With on‐going improvements in LED performance over the coming years, LED backlights will reach and even outperform the brightness performance of direct‐lit backlights while maintaining the benefits of edge‐lit solutions at even higher brightness levels.     

Seventeen‐inch laser backlight in‐plane switching liquid crystal display with 8K, 120‐Hz driving,and BT.2020 color gamut

We have developed a 17‐inch laser backlight in‐plane switching liquid crystal display satisfying the main BT.2020 specifications, which are 8K, 120‐Hz driving, and a BT.2020 wide color gamut. The color gamut of the developed in‐plane switching liquid crystal display covers 98% of the BT.2020 wide color gamut, thanks to a laser backlight and appropriate color filters. The liquid crystal response time of 5 ms, which is sufficient for 120‐Hz driving, is achieved by adapting a faster in‐plane switching liquid crystal display, namely, the short‐range lurch control in‐plane switching liquid crystal display.     

A field‐sequential‐color display with a local‐primary‐desaturation backlight scheme

Abstract— Field‐sequential‐color technology eliminates the need for color filters in liquid‐crystal displays (LCDs) and results in significant power savings and higher resolution. But the LCD suffers from color breakup, which degrades image quality and limits practical applications. By controlling the backlight temporally and spatially, a so‐called local‐primary‐desaturation (LPD) backlight scheme was developed and implemented in a 180‐Hz optically compensated bend (OCB) mode LCD equipped with a backlight consisting of a matrix of light‐emitting diodes (LEDs). It restores image quality by suppressing color breakup and saves power because it has no color filter and uses local dimming. A perceptual experiment was implemented for verification, and the results showed that a field‐sequential‐color display with a local‐primary‐desaturation backlight reduced the color breakup from very annoying to not annoying and even invisible.     

Use of quantum rods for display applications

We examined the use of quantum rods (QRs) in two configurations for display applications, including the backlight and emissive color pixels for liquid crystal and organic light‐emitting diode displays, respectively. For the backlight, we used an electrospun nanofiber sheet embedded with QRs, and found the nanofiber‐aligned sheet showed polarized emission with a very high outcoupling efficiency. We then fabricated emissive color pixels with QRs using an inkjet printer, and evaluated their optical properties. The color gamut area size was 82% of the BT2020 standard and the overlap with it was 69%.     

Color performance of an MVA‐LCD using an LED backlight

Abstract— The color performance, including color gamut, color shift, and gamma curve, of a multi‐domain vertical‐alignment (MVA) liquid‐crystal display (LCD) using an LED backlight are calculated quantitatively. Simulation results indicate that an LED backlight exhibits better angular color uniformity and smaller color shifts than a CCFL backlight. Color gamut can be further widened and color shift reduced when using a color‐sequential RGB‐LED backlight without color filters, while the angular‐dependent gamma curves are less influenced using different backlights. The obtained quantitative results are useful for optimizing the color performance and color management of high‐end LCD monitors and LCD TVs.     

Physical‐based photon mapping for an LED backlight lighting simulator

Abstract— Liquid‐crystal displays (LCDs) have become increasingly popular due to their lower price and larger sizes. In particular, backlights having an RGB LED source have recently attracted attention, because they have a wider color gamut, higher luminance, and lower power consumption. However, even when the backlight area is uniformly covered with light modules based on arrays of individual LEDs, this does not ensure a uniform chromaticity and luminance over the backlight panel, thereby stressing the need for lighting simulation of the backlight. Accordingly, this paper proposes an effective lighting simulator to predict the chromaticity and luminance distribution of an LED backlight panel for an LCD. First, the spectrum‐based photons are all initially generated using a random function with a constraint satisfying the spectral power distribution of the actual LED light sources, while their emitting directions are determined based on a pre‐calculated probability using a random variable angle. The optical characteristics of the inner sheets in the LCD backlight structure are then modeled using the wavelength and incident angle to predict the next direction of each photon based on the reflection and transmittance at an intersection. All the photons that reach the unit area of the outward panel are gathered to shape their spectral power distribution, then converted to CIEXYZ values and multiplied with a color‐matching function. Finally, a realistic image visualization of these CIEXYZ values is achieved through standardized device characterization using the sRGB mode. Experiments confirm that the proposed spectrum‐based photon mapping can effectively predict the chromaticity and luminance distribution of an LED backlight panel, providing a good lighting simulation of an LED backlight before manufacturing the LCD.     

Projection displays: New technologies,challenges, and applications

The achievable color gamut and light output of projection displays based on light‐emitting diodes (LEDs), phosphor conversion, and lasers are discussed. The color appearance phenomena, colorfulness, and the Helmholtz–Kohlrausch effect are discussed in the context of LED and laser illumination of projection displays, as well as some pitfalls concerning the interpretation of the Helmholtz–Kohlrausch effect. Also the laser speckle phenomenon and the characterization of it are addressed. The importance of both the American National Standards Institute (ANSI) contrast and the sequential contrast of projectors, as well as the discrepancy between measured and perceived contrasts, are explained. Visibility criteria for contouring artifacts are explained and compared with new emerging electro‐optical transfer functions that are more adapted to this issue. Stereoscopic solutions and early prototypes of autostereoscopic multi‐view, super multi‐view projection displays, and electro‐holographic displays are discussed as well as the limiting factors of these systems in the context of display resolution, and LED and laser light sources.     

Power‐saving primary design for displays enclosing a target color gamut

Abstract— Display primaries are optimized for the trade‐off between the total primary power and color gamut under the requirement that a target color gamut is enclosed by the color gamut of the display. LED displays and HDTV color gamut are taken as examples. Compared to the display using a set of typical commercial RGB LEDs, it was found that a total optical (electrical) power of 23.6% (15.6%) can be saved for the display using optimal RGB LEDs. Although the size of the display color gamut is sacrificed, the color gamut of the display using optimal RGB LEDs still encloses the HDTV color gamut. The combined effect of the LED luminous efficiency and white‐point condition on the determination of the optimal LED wavelengths and bandwidths is also studied.     

Energy‐efficient liquid‐crystal displays (e2‐LCDs) using a photonic‐crystal backlight system

Abstract— Cholesteric liquid crystals automatically form one‐dimensional photonic crystals. For a photonic crystal in which light‐emitting moieties are embedded, unique properties such as microcavity effects and simultaneous light emission and light reflection can be expected. Three primary‐color photonic‐crystal films were prepared based on cholesteric liquid crystal in which fluorescent dye is incorporated. Microcavity effects, i.e., emission enhancement and spectrum narrowing, were observed. Two types of demonstration liquid‐crystal displays (LCDs) were fabricated using the prepared photonic‐crystal films in a backlight system. One is an area‐color LCD in which a single photonic‐crystal layer is used for each color pixel and the other is a full‐color TFT‐LCD in which three stacked photonic‐crystal layers are used as light‐conversion layers. The area‐color LCD was excited by using 365‐nm UV light, and the full‐color TFT‐LCD was excited by using 470‐nm blue LED light. Because of the photonic crystal's unique features that allow it to work as light‐emitting and light‐reflecting layers simultaneously, both LCDs demonstrate clear readable images even under strong ambient light, such as direct‐sunlight conditions, under which conventional displays including LCDs and OLED displays cannot demonstrate clear images. In particular, an area‐color LCD, which eliminated color filters, gives clear images under bright ambient light conditions even without backlight illumination. This fact suggests that a backlight system using novel photonic‐crystal layers will be suitable for energy‐efficient LCDs (e²‐LCDs), especially for displays designed for outdoor usage.     

Wide gamut LCD using locally dimmable four‐primary‐color LED backlight

This paper proposes a wide gamut LCD using locally dimmable four‐primary‐color (4PC) LED backlight. Although the color gamut of LCDs has been improved in recent years, it is insufficient to reproduce all the colors in the real world. The objective of this paper is to propose a wide gamut LCD that reproduces all the colors in the real world while keeping the cost increases to a minimum. We evaluated the color gamut reproduced by LEDs of multiple primary colors and selected cyan as the optimal color to be added to the three primary colors to reproduce all the colors in the real world. Therefore, we designed an LED backlight consisting of an additional only‐cyan LED with three‐primary‐color LEDs and developed a prototype LCD with 4PC LED backlight. Furthermore, we developed a local dimming algorithm for the 4PC LED backlight. As a result, we confirmed that the prototype LCD with the 4PC LED backlight is able to cover almost all the colors in the real world and also able to display natural images with highly saturated colors by local dimming.     

Diffractive backlight grating array for mobile displays

Abstract— The display backlight unit (BLU) is the most power‐consuming subunit in mobile liquid‐crystal displays. The state‐of‐the‐art BLUs utilize scattering, refractive, and reflective microstructures to generate a uniform distribution of white light through the display. More effective means of transmitting light through the display color filters could be obtained by using diffraction, but previously proposed diffractive backlights do not fully utilize all the possibilities to design gratings effectively for optimal color separation and outcoupling. This paper presents a new pixelated diffractive backlight grating array as an approach for overcoming these obstacles in BLU design. A model array was fabricated to couple out red, green, and blue primary colors from the respective subpixel locations. The results show that it is possible to manufacture such an array and that the light couples out as intended, giving a starting point to design mobile‐display modules with low light‐transmission losses.     

Patterned liquid‐crystal laser film for multi‐dimensional multi‐color emissive film technology

Abstract— A two‐dimensional array consisting of dye‐doped reflection‐mode holographic‐polymer‐dispersed liquid crystal (H‐PDLC) lasers with alternating pitch lengths is presented. These post structures each reflect at a narrow bandwidth of light. The addition of laser dye to the H‐PDLC system allows for the generation of laser emission at the edge of the reflection band, or photonic band gap. In patterning these H‐PDLC post structures, a narrow‐linewidth patterned emissive color film is realized. The potential of such films and their implication in the display industry is discussed. In creating a three‐color array, an active emissive color film could replace the backlight and color filter components within the display. Such a patterned system would possess a wide color gamut, through spatial color synthesis, formed by narrow‐linewidth lasing structures with well‐defined wavelengths of emission.     

Spatio‐temporal scanning backlight mode for field‐sequential‐color optically‐compensated‐bend liquid‐crystal display

Abstract— A spatially and temporally scanning backlight consisting of ten isolated micro‐structured light guides has been developed to be combined with a fast‐response optically‐compensated‐bend‐mode field‐sequential‐color LCD in which the liquid‐crystal cell does not contain color filters. The sequential fields of three primary colors are generated by illumination of the red‐, green‐, and blue‐light‐emitting diodes, each illuminating for one‐half of the field, resulting in a luminance of 200 cd/m² for the LCD. The effect of light leakage between the blocks in the scanning backlight in field‐sequential‐color applications was measured and will be described.     

Backlight unit with double‐surface light emission using a single micro‐structured lightguide plate

Abstract— A novel illumination system for a liquid‐crystal‐display (LCD) module used in a dual‐display cellular phone has been developed. A double‐surface light‐emitting backlight uses a single light‐guide plate to illuminate both LCDs. A single lightguide, two prism sheets, and four light‐emitting diodes (LED) were used in the new structure, compared with ten components and two sets of light sources with six LEDs in the current backlight. The thickness and power consumption of the new backlight were reduced by a factor of 0.59 and 0.67, respectively.     

New display concept for realistic reproduction of high-luminance colors

A new display concept for reproduction of high-luminance colors based on a liquid crystal display has been developed using a brighter backlight unit and color mapping algorithms. The new concept is able to display brighter colors close to a peak luminance of a display white than conventional displays so that realistic scene of brighter colors is better reproduced. It may also be one of the future display solutions needed to extend the color gamut in the direction of brighter colors, which is a principal limitation in conventional displays even in high-dynamic range display systems. With the new concept, an xvYCC- (extended-video YCbCr) compatible display can be easily realized.     

Fast full‐color reflective display via photoluminescent enhancement

Reflective displays are advantageous in applications requiring low power or daylight readability. However, there are no low‐cost reflective technologies capable of displaying bright colors. By employing photoluminescence to more efficiently use ambient light, we created a prototype display that provides bright, full color in a simple, low‐cost architecture. This prototype includes a novel electrokinetic shutter, a layer that incorporates patterned luminescent red, green, and blue sub‐pixel elements, and a novel optical out‐coupling scheme. The luminescent elements convert otherwise‐wasted portions of the incident spectrum to light in the desired color band, resulting in improved color saturation and lightness. This prototype provides a color gamut that is superior to competing reflective display technologies that utilize color filters in single‐layer side‐by‐side sub‐pixel architectures. The current prototype is capable of switching in <0.5 s; future displays based on an alternative electro‐optic shutter technology should achieve video rate operation. A transflective version of this technology has also been prototyped. The transflective version utilizes its backlight with a power efficiency that is at least three times that of a conventional liquid crystal display. These photoluminescence‐based technologies enable a host of applications ranging from low‐power mobile products and retail pricing signage to daylight readable signage for outdoor advertising segments.     

All solution‐processed white quantum‐dot light‐emitting diodes with three‐unit tandem structure

Quantum‐dot light‐emitting diodes (QLEDs) are promising candidates for next generation displays. White QLEDs which can emit red, green and blue colors are particularly important; this is because the combination of white QLEDs and color filters offers a practical solution for high‐resolution full‐color displays. In this work, we demonstrate all‐solution processed three‐unit (red/green/blue) white tandem QLEDs for the first time. The white tandem devices are achieved by serially connecting the red bottom sub‐QLED, the green middle sub‐QLED and the blue top sub‐QLED using the inter‐connecting layer (ICL) based on ZnMgO/PEDOT:PSS heterojunction. With the proposed ICL, the two‐unit tandem QLEDs exhibit a high current efficiency of 22.22 cd/A, while the three‐unit white QLEDs exhibit evenly separated red, green and blue emission with a CIE coordinate of (0.30, 0.44), a peak current efficiency of 4.75 cd/A and a high luminance of 4206 cd/m². Displays based on the developed white QLEDs exhibit a wide color gamut of 114% NTSC. This work confirms the effectiveness of the proposed ZnMgO/PEDOT:PSS ICL and the feasibility of making all‐solution processed tandem white QLEDs by using the proposed ICL.     

Analysis of color volume of multi‐chromatic displays using gamut rings

There are claims that multi‐chromatic displays can achieve a wider color gamut by the use of additional highly saturated secondary color channels. However, there are other claims that these displays lose lightness and/or color saturation at brighter levels. These apparently divergent views have led to some controversy in the display industry and at standard setting organizations. This study examines the color gamut volume for a variety of simulated and measured multi‐chromatic (sometimes incorrectly referred to as “multi‐primary”) displays using combinations of white and/or secondary color channels, such as cyan, magenta, and yellow. Furthermore, a two‐dimensional gamut representation, referred to as “gamut rings,” is introduced to illustrate that the addition of nonprimary optical color channels to a trichromatic (RGB) display can result in a significant decrease in the chroma at higher lightness levels. The additional saturated color channels can increase the gamut volume only around their hues at darker levels. The results also confirm the validity of comparing the color light output and white light output for revealing the design trade‐offs between the high‐peak white and the color‐image brightness for multi‐chromatic displays.