The effects of incorporated nano/micro‐diamond (NMD) on the physical properties, crystallization, thermal/hydrolytic degradation of poly(L ‐lactic acid) (PLLA) were investigated for a wide NMD concentration range of 0–10 wt.‐%. Incorporated NMD increased the tensile modulus and strength of PLLA films but decreased the elongation at break of PLLA films. Incorporated NMD accelerated the crystallization of PLLA during heating and cooling and increased the absolute crystallization enthalpy of PLLA films (except for an NMD concentration of 10 wt.‐% during cooling) but did not alter the crystallization mechanism. Incorporated NMD increased and decreased the thermal stability of PLLA films for NMD concentrations of 1–5 and 10 wt.‐%, respectively, and increased the hydrolytic degradation resistance of PLLA films.
PHBV is produced by bacteria as intracellular carbon storage. It is advantageous concerning biocompatibility and biodegradability, but its low crystallization rate hinders the melt‐processing of fibers. This problem can be overcome by combining PHBV with PLA in a core/sheath configuration and introducing a new spin pack concept. The resulting PHBV/PLA bicomponent fibers show an ultimate tensile stress of up to 0.34 GPa and an E‐modulus of up to 7.1 GPa. XRD reveals that PLA alone is responsible for tensile strength. In vitro biocompatibility studies with human fibroblasts reveal good cytocompatibility, making these fibers promising candidates for medical therapeutic approaches.
Thermo‐responsive PNIPAAm/PLLA nanofibrous films with tunable surface morphologies and better biocompatibility were prepared by electrospinning technique. The electrospun composite films possessed a “bead‐on‐string” structure. The wettability of nanofibrous films was observed by water CA measurements. The results showed that the electrospinning process and addition of PLLA did not change the thermo‐sensitivity of PNIPAAm. The wettability of electrospun PNIPAAm/PLLA composite films could switch from superhydrophilic to superhydrophobic when the temperature increased from 20 to 50 °C. Electrospinning is a promising way to create stimuli‐responsive surfaces with potential application in the design and tactics of controllable drug delivery system.
New talc/PBAT hybrid materials were prepared through reactive extrusion. First, PBAT was free‐radically grafted with MA to improve the interfacial adhesion between PBAT and talc. Then, the resulting MA‐g‐PBAT was reactively melt‐blended with talc through esterification reactions of MA moieties with the silanol functions from talc. Sn(Oct)2 and DMAP were used as catalysts. Interestingly, the tensile properties for these compatibilized composites were improved due to a better interfacial adhesion between both partners. XPS showed the formation of covalent ester bonds between the silanol functions from talc particles, and the MA moieties grafted onto the polyester backbones.
The crystallization behavior of poly(L ‐lactide) (PLLA) was investigated in the presence of benzenetricarboxylamide (BTA) derivatives as crystal nucleators. BTA‐cyclohexyl (BTA‐cHe) was the most effective nucleating agent, but induced a complete loss of transparency of the processed material. On the other hand, BTA‐n‐hexyl (BTA‐nHe) enhanced crystallization with little increase in haze. PLLA containing BTA‐cHe enhanced PLLA crystallization in α‐form crystal whereas BTA‐nHe enhanced α′‐form (incomplete α‐form) with forming smaller spherulites. TEM revealed BTA‐nHe had completely dissolved in the PLLA matrix in melt and recrystallized during the thermal annealing process. It was also found that the size of the recrystallized BTA‐nHe was in the nanometer range to effectively nucleate the PLLA crystals.
Low density polyethylene (LDPE) was prepared into micro‐ or submicro‐spheres or nanofibers via melt blending or extrusion of cellulose acetate butyrate (CAB)/LDPE immiscible blends and subsequent removal of the CAB matrix. The sizes of the PE spheres or fibers can be successfully controlled by varying the composition ratio and modifying the interfacial properties of the blends. The surface structures of LDPE micro‐ or submicro‐spheres and nanofibers were analyzed using SEM and FTIR‐ATR spectroscopy. In addition, the crystalline structures of the LDPE nanofibers were characterized.
A new technique for design and preparation of self‐reinforced starch films is introduced. The films were based on a high‐amylose corn starch that was chemically modified in different ways. Hydroxypropylation was used to decrease gelatinization temperature and improve processability. The reinforcing component consisted of cross‐linked starch granules, where the crosslinking increased granule thermal stability and moisture resistance. Distribution of the cross‐linked starch was imaged by CLSM, and the matrix/particle interface was studied by SEM. Modulus and tensile properties of the starch film were increased by about 30 and 20%, respectively, after addition of rigid cross‐linked starch particles. A perfect interface between matrix and reinforce agent was obtained.
In the general processing temperature range of poly(L ‐lactic acid) (PLLA) articles (210–240 °C), PLLA/poly(D ‐lactic acid) (PDLA) stereocomplex (SC) crystallites melted just above the endset temperature of SC melting (228–238 °C) and recrystallized during cooling were found to act as the most effective nucleating agents for enhancing the crystallization of PLLA compared to partially melted SC crystallites (211–227 °C) or those melted far above the endset temperature of SC melting (240 and 250 °C) and recrystallized during cooling. The high nucleating effect of the SC crystallites melted in the temperature range of 228–238 °C was found to be caused by their smaller sizes or the larger number of SC crystallites per unit mass. The incorporation of such SC crystallites facilitates the processing of PLLA articles having high crystallinity and, therefore, high heat‐resistance in a shorter period to reduce the production cost.
Shape‐memory properties such as shape fixity and recovery ratio of amorphous starch‐based materials extruded under normal conditions were evaluated for the case of single and cyclic recovery processing. This study focused on the effect of moisture as a stimulus for the activation of recovery. A high recovery ratio (Rr > 90%) was obtained at high relative humidity, at deformation ratios up to 200%. In the case of plasticized starch with a glycerol content of 10%, the recovery ratio was close to 50% because crystallization limited the shape recovery. Results were compared to those obtained with synthetic or bio‐based shape‐memory polymers such as semi‐crystalline PU or PLAGC. Efficient shape memory properties for a non‐modified biopolymer are highlighted in this study.
Oriented precursors of MFCs consisting of HDPE and PA6 or PA12 are studied during strain‐controlled slow load‐cycling. In the PA6‐containing blends a strongly retarded nanostrain response is detected. Compatibilization induces nanostrain heterogenization. Stress fatigue is lower in the PA12 blends, but hardly decreased by the compatibilizer. Selective migration of the compatibilizer into a disordered semi‐crystalline fraction of the HDPE matrix can explain the findings. The semi‐crystalline HDPE entities in PA6 blends appear more disordered than in PA12‐blends. An analysis of the HDPE nanostructure evolution during cycling reveals epitaxial strain crystallization. Uncompatibilized PA6 blends cycled about high pre‐strain show plastic flow but nanoscopic shrinkage in the semi‐crystalline stacks.
The effect of nanosilica addition on the morphology and mechanical properties of blends of isotactic PP and an ethylene/octene copolymer (EOC) is studied. TEM reveals that the well‐dispersed nanoparticles are localized exclusively in the PP phase. In the presence of a maleated PP compatibilizer addition of nanosilica leads to more finely dispersed EOC domains and a finer co‐continuous morphology. The nanoparticles reduce the rate of coalescence of the dispersed phase domains. The mechanical properties depend on the EOC and PP‐g‐MA content. Tensile and flexural properties are significantly enhanced in the presence of the silica nanoparticles, whereas impact properties are not affected. These enhancements are attributed to the favorable microstructure of the blends.
The effect of aging on the thermo‐mechanical properties of new biocomposite materials obtained from renewable resources is studied. Cellulose was used as the reinforcing phase and the matrix was composed of a blend of two biopolymers (PEM and PLLA) in order to have a good compromise between stiffness and flexibility. Two grafting agents were used to compatibilize the filler with the matrix. The ensuing materials were then aged at 35 °C and 80% relative humidity during 45 days. Thermal and dynamic mechanical properties of the blends and composites were measured before and after aging. Important variations of crystallinity were observed and results show that grafting allowed obtaining high‐performance composites even after aging.
TPVs are prepared by dynamic vulcanization in which crosslinking of an elastomeric polymer takes place during its melt mixing with a thermoplastic polymer under high‐shear conditions. 30:70 wt% blends of PP and ethylene–octene copolymer are vulcanized using electron‐induced reactive processing (EIReP) employing a range of absorbed doses (25, 50, and 100 kGy) while keeping the electron energy and treatment time fixed. The structure/property relationships of the prepared samples are studied using various characterization techniques such as DMA, DSC, SEM, and melt rheology. The results suggest that EIReP offers a novel route to prepare TPVs without any chemical crosslinking and coupling agents.
Novel and potent inhibitors of Plasmodium falciparum plasmepsin II were identified by post‐processing the results of a docking screening with BEAR, a recently reported procedure for the refinement and rescoring of docked ligands in virtual screening. FRET substrate degradation assays performed on the 30 most promising compounds resulted in 26 inhibitors with IC50 values ranging from 4.3 nM to 1.8 μM .
DSC indicated that the nucleation of PLLA is enhanced in the presence of PGA even at a PGA content as low as 0.1 wt.‐%. However, the enhancing behavior of PGA was different to that of other nucleating agents for PLLA. Polarized optical microscopy revealed that the presence of PGA increased the number of PLLA spherulites per unit area. WAXD showed that in the PLLA/PGA films, PLLA and PGA crystallize separately to form their respective crystallites and PGA crystallites were formed at a PGA content at above 3 wt.‐% (at least). FTIR spectroscopy indicated that that there are significant interactions between PLLA and PGA chains in amorphous regions. Such interactions should have enhanced the growth of PLLA crystallites from the surface of PGA crystallites.
TMC/LLA copolymers with several TMC/LLA ratios are synthesized and a composite is obtained by reinforcing with short PLGA fibers. In vitro degradation is studied at 37 °C in pH = 7.4 buffer and compared with a PLLA homopolymer. The degradation of the copolymers appears slower than that of PLLA, showing that TMC units are more resistant to hydrolysis than LLA. Compositional changes indicate a preferential degradation of LLA units as compared to TMC ones. Morphological changes with crystallization of degradation by‐products are observed. The composite degrades much faster than the neat copolymer and PLLA because the faster degradation of PLGA fibers speeds up the degradation of the matrix. The composite appears promising for the fabrication of totally bioresorbable stents.
This paper demonstrates how the electric‐field‐assisted thermal annealing of octadecylamine‐functionalized SWNT/PMMA films induces an increase in the composite transversal conductivity of several orders of magnitude and a decrease in the lateral conductivity. This difference has been rationalized in terms of the nanotube alignment into the polymer matrix along the electric field direction. This result provides an initial understanding of how electric fields can be used to control the bulk physical properties of such nanocomposites.
The effects of nucleobases, especially uracil, on the nonisothermal and isothermal crystallization, melting behavior, spherulite morphology, and crystalline structure of bio‐based and biodegradable PLLA are studied. The melt‐ and cold‐crystallization rates of PLLA increase with increasing uracil loading. The melting behavior of nonisothermally melt‐ and cold‐crystallized PLLAs depends on the uracil content. The isothermal crystallization kinetics is analyzed based on an Avrami model. The incorporation of uracil changes the t1/2/Tc profile of PLLA due to the more distinct heterogeneous nucleation effects at small supercooling. The crystalline structure of PLLA is not affected by uracil presence. The nucleation density increases and the spherulite size decreases by uracil incorporation.
The effectiveness and efficiency of an ethylene/acrylate copolymer in toughening semicrystalline and amorphous PLA through melt blending is studied. The mechanical properties, phase morphologies, miscibilities, and toughening mechanisms of the blends are assessed. The ethylene/acrylate impact modifier effectively improved the impact strength of the blends, regardless of the PLA type. The semicrystalline blends showed decreased tensile strength and modulus with increased impact modifier content. In contrast, the ductility, elongation at break, and energy to break increased significantly. The relatively low BDT temperature obtained for the PLA blends renders the ethylene/acrylate copolymer impact modifier a desirable additive to toughen PLA for use in cold temperatures.
PLLA and stereocomplexed polylactide (sc‐PLA) nanofibers were formed by electrospinning solutions of the polymers in HFIP. A highly semi‐crystalline sc‐PLA nanofiber having only sc crystallites was confirmed by WAXD analysis. The diameters of the nanofibers of both polymers decreased slightly when they were annealed at 60 °C, which was near Tg. Enzyme degradation of both as‐spun PLLA and sc‐PLA nanofibers by proteinase K from Tritirachium album was carried out. The rate of degradation of the nanofibers can be controlled by varying annealing conditions, hence the extent of crystallinity.
