Associations between a hydrophobically modified,degradable, poly(malic acid) and a β‐cyclodextrin polymer in solution

A new associating system has been elaborated from mixing a degradable polymer, poly(β‐malic acid‐co‐β‐ethyladamantyl malate), and a β‐cyclodextrin polymer in aqueous solution. Viscosity and dynamic light scattering measurements have been made on solutions of the single copolyester and of mixtures of both polymers. Studies on copolyesters with different percentages of hydrophobic groups (0–7.5%) show that a small proportion of the chains (less than 5% in weight) are aggregated in large structures (100 nm) which dominate the scattering intensity. The mixtures exhibit slow diffusive relaxation modes which correlate with a large viscosity enhancement at low concentration. These effects, which depend sensitively on pH, are attributed to the presence of polydisperse complexes of copolyester and β‐cyclodextrin polymer. The influence of pH, ionic strength, medium composition, and concentration were examined on the mixture of copolymers. It was found that the association properties are controlled by the net charge on the amphiphilic copolyester. © 2001 Society of Chemical Industry     

Swelling behaviour of poly(α‐hydroxyacrylic acid) gel

Poly(α‐hydroxy acrylic acid) (PHA) and poly(acrylicacid) (PAA) gels were prepared by irradiating the respective 15 wt% aqueous solutions with γ‐rays. Swelling ratios for PHA gel were measured as a function of pH and divalent cation (Mg²⁺, Ca²⁺, Mn²⁺, Co²⁺, Ni²⁺, Cu²⁺) concentration C₂ in the external solution to provide a comparison with the results for PAA gels. It was found that the swelling ratio of PHA gel steeply increases between pH 2 and 4, followed by a gradual swelling in the higher pH region. The corresponding steep swelling of PAA gel was observed at pH 3–6. Cation specificity in the equilibrium swelling ratio at a lower C₂ value (1.0 × 10⁻³ M) was approximately consistent with the binding selectivity in the solution system. Typically, the swelling ratio of PHA gel in the presence of Ca²⁺ was significantly lower than in the Mg²⁺ system, while the difference was slight for PAA gel. The response of the swelling ratio to changes in pH and C₂ was analysed as a first order relaxation to estimate the time constants. The (de)swelling kinetics measured by both the pH and C₂ jump were qualitatively interpreted in terms of main‐chain stiffness and intermolecular hydrogen bonding in the respective polymers. © 2000 Society of Chemical Industry     

Cationic copolymers of α,β‐poly‐(N‐2‐hydroxyethyl)‐DL‐aspartamide (PHEA) and α,β‐polyasparthylhydrazide (PAHy): synthesis and characterization

In the present study the derivatization of two water‐soluble synthetic polymers, α,β‐poly(N‐2‐hydroxyethyl)‐DL ‐aspartamide (PHEA) and α,β‐polyasparthylhydrazide (PAHy), with glycidyltrimethylammonium chloride (GTA) is described. This reaction permits the introduction of positive charges in the macromolecular chains of PHEA and PAHy in order to make easier the electrostatic interaction with DNA. Different parameters affect the reaction of derivatization, such as GTA concentration and reaction time. PHEA reacts partially and slowly with GTA; on the contrary the reaction of PAHy with GTA is more rapid and extensive. The derivatization of PHEA and PAHy with GTA is a convenient method to introduce positive groups in their chains and it permits the preparation of interpolyelectrolyte complexes with DNA. © 2000 Society of Chemical Industry     

Preparation of poly(ε‐caprolactone)/poly(ε‐caprolactone‐co‐lactide) (PCL/PLCL) blend filament by melt spinning

Poly(ε‐caprolactone)/poly(ε‐caprolactone‐co‐lactide) (PCL/PLCL) blend filaments with various ratios of PCL and PLCL were prepared by melt spinning. The effect of PLCL content on the physical properties of the blended filament was investigated. The melt spinning of the blend was carried out and the as spun filament was subsequently subjected to drawing and heat setting process. The addition of PLCL caused significant changes in the mechanical properties of the filaments. Crystallinity of blend decreased with the addition of PLCL as observed by X‐ray diffraction (XRD) and differential scanning calorimetry (DSC). Scanning electron microscopy (SEM) revealed that the fracture surface becomes rougher at higher PLCL content. It may be proposed that PCL and PLCL show limited interaction within the blend matrix. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Miscibility of block copolymers of poly(ε‐caprolactone) and poly(ethylene glycol) with poly(3‐hydroxybutyrate) as well as the compatibilizing effect of these copolymers in blends of poly(ε‐caprolactone) and poly(3‐hydroxybutyrate)

Atactic poly(3‐hydroxybutyrate) (a‐PHB) and block copolymers of poly(ethylene glycol) (PEG) with poly(ε‐caprolactone) (PCL‐b‐PEG) were synthesized through anionic polymerization and coordination polymerization, respectively. As demonstrated by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA) measurements, both chemosynthesized a‐PHB and biosynthesized isotactic PHB (i‐PHB) are miscible with the PEG segment phase of PCL‐b‐PEGs. However, there is no evidence showing miscibility between both PHBs and the PCL segment phase of the copolymer even though PCL has been block‐copolymerized with PEG. Based on these results, PCL‐b‐PEG was added, as a compatibilizer, to both the PCL/a‐PHB blends and the PCL i‐PHB blends. The blend films were obtained through the evaporation of chloroform solutions of mixed components. Excitingly, the improvement in mechanical properties of PCL/PHB blends was achieved as anticipated initially upon the addition of PCL‐b‐PEG. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2600–2608, 2001     

Largely improved tensile extensibility of poly(L‐lactic acid) by adding poly(ε‐caprolactone)

Poly(L ‐lactic acid) (PLLA) has good biocompatibility, biodegradability and physical properties. However, one of the drawbacks of PLLA is its brittleness due to the stiff backbone chain. In this work, a largely improved tensile toughness (extensibility) of PLLA was achieved by blending it with poly(ε‐caprolactone) (PCL). To obtain a good dispersion of PCL in the PLLA matrix, blends were prepared via a solution‐coagulation method. An increase in extensibility of PLLA of more than 20 times was observed on adding only 10 wt% of PCL, accompanied by a slight decrease in tensile strength. However, annealing of the samples led to a sharp decrease of extensibility due to phase separation and a change of crystalline structure. To conserve the good mechanical properties of PLLA/PCL blends, the blends were crosslinked via addition of dicumyl peroxide during the preparation process. For the crosslinked blend films, the extensibility was maintained nearly at the original high value even after annealing. Morphological analysis of cryo‐fractured and etched‐smoothed surfaces of the PLLA/PCL blends was carried out using scanning electron microscopy. Differential scanning calorimetry and polarized light microscopy experiments were used to check the possible change of crystallinity, melting point and crystal morphology for both PLLA and PCL after annealing. The results indicated that the combination of solution‐coagulation and crosslinking resulted in a good and stable dispersion of PCL in the PLLA matrix, which is considered as the main reason for the observed improvement of tensile toughness. Copyright © 2010 Society of Chemical Industry     

Ruthenium(II)‐Catalyzed Protocol for Preparation of Diverse α,β‐ and β,β‐Dihaloenones from Diazodicarbonyls

Efficient one‐step syntheses of α,β‐ and β,β‐dihaloenones were achieved by ruthenium(II)‐catalyzed reactions between cyclic or acyclic diazodicarbonyl compounds and oxalyl chloride or oxalyl bromide in moderate to good yields. This methodology offers several significant advantages, which include ease of handling, mild reaction conditions, one‐step reaction, and the use of an effective and non‐toxic catalyst. The synthesized compounds were further transformed into highly functionalized novel molecules bearing aromatic rings on the enone moiety using the Suzuki reaction.

     

Synthesis and characterization of fullerene grafted poly(ε‐caprolactone)

The fullerene grafted poly(ε‐caprolactone) (PCL) was successfully synthesized with a graft efficiency of 80%. The fullerene moieties grafted onto the PCL chain aggregate into 1–2 μm particles so that a physical pseudo‐network is formed. Because of the existence of the network structure, the fullerene grafted PCL film can retain its shape at much higher temperatures than that of pure PCL film, as observed in dynamic mechanical tests. It shows a hydrophobic gelling behavior in chloroform solution. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Biodegradable poly(vinyl alcohol)‐graft‐ poly(ε‐caprolactone) comb‐like polyester: Microwave synthesis and its characterization

Poly(vinyl alcohol)‐initiated microwave‐assisted ring opening polymerization of ε‐caprolactone in bulk was investigated, and a series of poly(vinyl alcohol)‐graft‐poly(ε‐caprolactone) (PVA‐g‐PCL) copolymers were prepared, with the degree of polymerization (DP) of PCL side chains and the degree of substitution (DS) of PVA by PCL being in the range of 3–24 and 0.35–0.89, respectively. The resultant comb‐like PVA‐g‐PCL copolymers were confirmed by means of FTIR, ¹H NMR, and viscometry measurement. The introduction of hydrophilic backbone resulted in the decrease in both melting point and crystallization property of the PVA‐g‐PCL copolymers comparing with linear PCL. With higher microwave power, the DP of PCL side chains and DS of PVA backbone were higher, and the polymerization reaction proceeded more rapidly. Both the DP and monomer conversion increased with irradiation time, while the DS increased first and then remained constant. With initiator in low concentration, the DP and DS were higher, while the monomer was converted more slowly. Microwaves dramatically improved the polymerization reaction in comparison of conventional heating method. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104, 3973–3979, 2007     

Addition of α‐tocopherol on poly(lactic acid): Thermal,mechanical, and sorption properties

This work investigates the effect of the addition of a well‐known antioxidant, α‐tocopherol in poly (lactic acid) flexural and barrier properties. For that purpose, films of poly(lactic acid) enriched with 0, 2.2, and 4.4% of α‐tocopherol were prepared. Differential scanning calorimetry, thermogravimetric analysis, and dynamic mechanical analysis were used to characterize the changes in the mechanical and thermal properties. The sorption of oxygen and carbon dioxide in the prepared enriched films of poly(lactic acid) was measured at different temperatures between 283 and 313 K and pressures up to atmospheric pressure using a Quartz Crystal Microbalance. Although no significant changes were found in the mechanical and thermal properties, the addition of α‐tocopherol promotes an increasing in the oxygen sorption and the convex shape of the isotherms indicate a strong interaction gas‐polymer. Regarding the sorption of carbon dioxide, no pronounced effect was found. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Interface formation of Ca with poly(p-phenylene α,α′-diphenyl vinylene) and poly(p-phenylene α-phenyl vinylene)

We have investigated the interface formation of Ca with poly(p-phenylene α,α′-diphenyl vinylene) (PPV-DP) and poly(p-phenylene α-phenyl vinylene) (PPV-P) using X-ray photoemission spectroscopy (XPS). Similarly to our earlier findings in metal/PPV interface formation, the O 1s peak shifted toward a lower binding energy as soon as Ca was deposited on to the polymers. This was accompanied by the formation of Ca? O, suggesting a chemical origin for the O 1s shift. By contrast, the C 1s peak shift toward a lower binding energy was observed relatively later, after about 4 Å of Ca deposition. At the same time, a new C 1s component became noticable at about ?1.5 eV relative to the initial C 1s peak. This component signifies the possibility of polymer disruption by the Ca atoms to form Ca? C species. The C 1s peak shift is attributed to Ca induced surface band bending and barrier formation as in the case of metal/PPV interface formation. The disruption of the polymer may also induce changes in the interface electronic states and contribute to the C 1s peak shift. From the intensity attenuation analysis, we conclude that the initial 15 Å of Ca overlayer is contaminated by the Ca? O and Ca? C species and the overlayer is pure beyond 15 Å of Ca coverage.     

Synthesis and characterization of polyrotaxanes comprising α‐cyclodextrins and poly(ε‐caprolactone) end‐capped with poly(butyl methacrylate)s

Biodegradable polyrotaxane‐based triblock copolymers were synthesized via the bulk atom transfer radical polymerization (ATRP) of n‐butyl methacrylate (BMA) initiated with polypseudo‐rotaxanes (PPRs) built from a distal 2‐bromoisobutyryl end‐capped poly(ε‐caprolactone) (Br‐PCL‐Br) with α‐cyclodextrins (α‐CDs) in the presence of Cu(I)Br/N,N,N′,N″,N″‐pentamethyldiethylenetriamine at 45 ºC. The structure was characterized in detail by means of ¹H NMR, gel permeation chromatography, wide‐angle X‐ray diffraction, DSC and TGA. When the feed molar ratio of BMA to Br‐PCL‐Br was changed from 128 to 300, the degree of polymerization of PBMA blocks attached to two ends of the PPRs was in the range 382 ? 803. Although about a tenth of the added α‐CDs were still threaded onto the PCL chain after the ATRP process, the movable α‐CDs made a marked contribution to the mechanical strength enhancement, blood anticoagulation activity and protein adsorption repellency of the resulting copolymers. Meanwhile, they could also protect the copolymers from the attack of H₂O and Lipase AK Amano molecules, exhibiting a lower mass loss as evidenced in hydrolytic and enzymatic degradation experiments. © 2013 Society of Chemical Industry     

Biodegradable studies of poly(trimethylenecarbonate‐ε‐caprolactone)‐block‐poly(p‐dioxanone), poly(dioxanone), and poly(glycolide‐ε‐caprolactone) (Monocryl®) monofilaments

The aim of the study was to investigate the mechanical properties and biodegradability of poly(trimethylenecarbonate‐ε‐caprolactone)‐block‐poly(p‐dioxanone) [P(TMC‐ε‐CL)‐block‐PDO] in comparison with poly(p‐dioxanone) and poly(glycolide‐ε‐caprolactone) (Monocryl®) monofilaments in vivo and in vitro. P(TMC‐ε‐CL)‐block‐PDO copolymer and poly(p‐dioxanone) were prepared by using ring‐opening polymerization reaction. The monofilament fibers were obtained using conventional melt spun methods. The physicochemical and mechanical properties, such as viscosity, molecular weight, crystallinity, and knot security, were studied. Tensile strength, breaking strength retention, and surface morphology of P(TMC‐ε‐CL)‐block‐PDO, poly(p‐dioxanone), and Monocryl monofilament fibers were studied by immersion in phosphate‐buffered distilled water (pH 7.2) at 37°C and in vivo. The implantation studies of absorbable suture strands were performed in gluteal muscle of rats. The polymers, P(TMC‐ε‐CL)‐block‐PDO, poly(p‐dioxanone), and Monocryl, were semicrystalline and showed 27, 32, and 34% crystallinity, respectively. Those mechanical properties of P(TMC‐ε‐CL)‐block‐PDO were comparatively lower than other polymers. The biodegradability of poly(dioxanone) homopolymer is much slower compared with that of two copolymers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 737–743, 2006     

Structure and Mechanical Properties of Poly(lactic acid) Filled with (Starch nanocrystal)‐graft‐poly(ε‐caprolactone)

Poly(ε‐caprolactone) (PCL) was grafted to the surface of starch nanocrystals (StN) via microwave‐assisted ROP. The resultant nanoparticles were then incorporated into a poly(lactic acid) matrix to produce fully‐biodegradable nanocomposites with good mechanical properties. A loading level of 5 wt.‐% StN‐g‐PCL resulted in simultaneous enhancements of strength and elongation. The StN‐g‐PCL self‐aggregated as rubbery microparticles to enhance the elongation by ca. 10‐fold over that of neat PLA. Meanwhile, the grafted PCL chains were miscible with PLA and formed a stress‐transferring interface to the StN, providing a reinforcing function.

     

Transesterification in homogeneous poly(ε‐caprolactone)–epoxy blends

Transesterification has been investigated in poly(ε‐caprolactone) (PCL)–epoxy blends. In the hot melt process, the hydroxyl on diglycidyl ether of bisphenol‐A (DGEBA) monomers is too low to give a noticeable transesterification reaction. In the postcure process, model reactions reveal that the hydroxyls from a ring‐opening reaction are able to react with the esters of PCL. In the meantime, the PCL molecular weight decrease and its distribution becomes broader. Nuclear magnetic resonance spectra reveal that fraction of the tertiary hydroxyls converts to secondary hydroxyls. In the cured DGEBA–3,3′‐dimethylmethylene‐di(cyclohexylamine)–PCL blend, a homogeneous morphology is achieved. PCL segments are grafted onto the epoxy network after postcuring and result in the lower T_g observed in the differential scanning calorimetry thermogram. A higher transesterification extent also results in broader transition peaks by dynamic mechanical analysis. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 75–82, 1999     

Influence of γ‐irradiation on poly(methyl methacrylate)

Poly(methyl methacrylate) (PMMA) was γ‐irradiated (5–20 kGy) by a ¹³⁷Cs source at room temperature in air. The changes in the molecular structure attributed to γ‐irradiation were studied by mechanical testing (flexure and hardness), size‐exclusion chromatography, differential scanning calorimetry, thermal gravimetric analysis, and both Fourier transform infrared and solution ¹³C‐NMR spectroscopy. Scanning electron microscopy was used to investigate the influence of the dose of γ rays on the fracture behavior of PMMA. The experimental results confirm that the PMMA degradation process involves chain scission. It was also observed that PMMA presents a brittle fracture mechanism and modifications in the color, becoming yellowish. The mechanical property curves show a similar pattern when the γ‐radiation dose increases. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 886–895, 2002     

Poly(vinyl pyrrolidone‐co‐vinyl acetate)‐graft‐poly(ε‐caprolactone) as a compatibilizer for cellulose acetate/poly(ε‐caprolactone) blends

Poly(vinyl pyrrolidone‐co‐vinyl acetate)‐graft‐poly(ε‐caprolactone) (PVPVAc‐g‐PCL) was synthesized by radical copolymerization of N‐vinyl‐2‐pyrrolidone (VP)/vinyl acetate (VAc) comonomer and PCL macromonomer containing a reactive 2‐hydroxyethyl methacrylate terminal. The graft copolymer was designed in order to improve the interfacial adhesiveness of an immiscible blend system composed of cellulose acetate/poly(ε‐caprolactone) (CA/PCL). Adequate selections of preparation conditions led to successful acquisition of a series of graft copolymer samples with different values of molecular weight ( ), number of grafts (n), and segmental molecular weight of PVPVAc between adjacent grafts (M_n (between grafts)). Differential scanning calorimetry measurements gave a still immiscible indication for all of the ternary blends of CA/PCL/PVPVAc‐g‐PCL (72 : 18 : 10 in weight) that were prepared by using any of the copolymer samples as a compatibilizer. However, the incorporation enabled the CA/PCL (4 : 1) blend to be easily melt‐molded to give a visually homogeneous film sheet. This compatibilizing effect was found to be drastically enhanced when PVPVAc‐g‐PCLs of higher and M_n (between grafts) and lower n were employed. Scanning electron microscopy revealed that a uniform dispersion of the respective ingredients in the ternary blends was attainable with an assurance of the mixing scale of several hundreds of nanometers. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and characterization of p‐perfluoro{1‐[2‐(2‐fluorosulfonyl‐ethoxy)propoxy]}ethylated poly(α‐methyl styrene)

p‐Perfluoro{1‐[2‐(2‐fluorosulfonyl‐ethoxy)propoxy]}ethylated poly(α‐ methyl styrene) 3 was synthesized via electron transfer of perfluoro‐di{2‐[2‐(2‐fluorosulfonyl‐ethoxy)propoxy]}propionyl peroxide 2 and poly(α‐methyl styrene) 1 at different reactant molar ratios (2 : 1). The modified polymer 3 was characterized by various techniques. The ring p‐substitution was proved by FTIR and ¹⁹FNMR. The desulfonation appeared at above 124°C was found by TGA. The molecular weight determined by GPC increased with the increase of reactant molar ratio, and the polydispersity values indicated there was no degradation of the parent polymer chain in the reaction. Followed by hydrolysis and acidification, the modified polymer 3 could be further quantitatively converted into its sulfonic form 4. Ion exchange capacity of novel polyelectrolyte 4 can be controlled by changing reactant molar ratio (2 : 1). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3615–3618, 2006