Investigation of the mechanical properties of DGEBA-based epoxy resin with nanoclay additives

The present study investigated the effect of nanoclay additives on the mechanical properties of diglycidyl ether of bisphenol A (DGEBA) epoxy resin. The resin was cured with diethyltoluene diamine (DETDA) hardener and four material variations produced through the addition of four types of nanoclays, respectively. The nanocomposites were prepared by the in situ polymerisation method with the aid of mechanical shearing. The properties of the nanocomposites investigated included tensile modulus, tensile strength, tensile strain and fracture toughness (K_IC). It was observed that while the addition of nanoclay significantly increased the elastic modulus and fracture toughness of DGEBA epoxy resin, it also significantly reduced the failure strength and failure strain with increasing nanoclay level. Possible mechanisms for the improvement and degradation of these properties of the epoxy–clay nanocomposite materials are discussed.     

Elastomeric epoxy nanocomposites: Nanostructure and properties

In polymer layered silicate nanocomposites, significant differences have been reported between the effects of the nano-reinforcement on rigid and elastomeric nanocomposites. In this paper, we have studied elastomeric nanocomposites based upon DGEBA epoxy resin filled with montmorillonite (MMT) and cured with a long-chain polyoxypropylene diamine, for comparison with analogous rigid nanocomposites. Ultrasonic mixing was used to disperse the MMT in the matrix to improve homogeneity and decrease the agglomerate size. Two different methods of nanocomposite preparation were used in which the MMT was first swollen with either the curing agent or the epoxy before the addition of, respectively, DGEBA or diamine. A better dispersion of the nanoclay in the matrix and a greater amount of intercalation occurred when the MMT was first swollen with the diamine. The effect of MMT concentrations up to 8 wt.% on the mechanical behaviour of the epoxy/MMT nanocomposites was investigated. It was found that the addition of MMT increased the tensile strength and modulus, although SAXS and TEM indicated that a significant fraction of the clay layers were not exfoliated. Nevertheless, the addition of the clay resulted in changes in the fracture surfaces, as indicated by SEM, consistent with the tensile results and indicative of toughening.     

Novel nanocomposites based on epoxy resin/epoxy-functionalized polydimethylsiloxane reinforced with POSS

The purpose of the present study is to develop novel nanocomposites based on diglycidylether of bisphenol A (DGEBA) combined with diglycidylether-terminated polydimethylsiloxane (DG-PDMS), reinforced with 10 wt.% (mono-/octa) epoxy POSS nanocages (MEP or OEP-POSS). DG-PDMS and POSS compounds were covalently incorporated into DGEBA resin via copolymerization of epoxy groups. The effect of both DG-PDMS and POSS nanoparticles on the curing reaction, glass transition temperature (T_g), thermal stability, hardness and morphology of DGEBA/DG-PDMS ± POSS nanocomposites were studied by DSC, FTIR, DMA, TGA, SEM/EDX, AFM and contact angle measurements. SEM/EDX and AFM results prove that OEP-POSS is well dispersed within DGEBA/DG-PDMS polymer matrix, while MEP-POSS forms large POSS aggregates. The thermo-mechanical properties of POSS based nanocomposites are also in good correlation with morphology features. MEP-POSS based nanocomposite with heterogeneous dispersion of POSS aggregates exhibits lower T_g value and thermal stability in comparison with OEP-POSS nanocomposite which exhibits a nanoscale dispersion of the POSS cages. The obtained T_g of OEP-POSS based nanocomposite increases with 31 °C in comparison with the unreinforced matrix. Moreover, this nanocomposite shows the highest storage modulus (E′) and hardness.     

Stiffness and vibration characteristics of SMA/ER3 composites with shape memory alloy short fibers

Shape memory alloys (SMAs) possess both sensing and actuating functions due to their shape memory effect, pseudo-elasticity, high damping capability and other remarkable characteristics. Combining the unique properties of SMAs with other materials can create intelligent or smart composites. In this paper, epoxy resin composites filled with Ni–Ti alloy short fibers were developed. Microstructure was observed using digital HF microscope. The dynamic mechanical properties were investigated by measuring the first vibration mode of clamped cantilever beams and by dynamic mechanical analysis (DMA). Moreover, the natural frequency of SMA composites was predicted theoretically. As a result, the temperature dependency of vibration property and DMA characteristics is affected largely due to the addition of SMA short fibers. The vibrational characteristics of SMA composites can be improved by the addition of small amounts of SMA short fibers. The addition of 3.5 wt.% of SMA short fiber content to epoxy resin resulted in the maximum increment in both natural frequency and storage modulus. This suggested that there exists an optimum SMA fiber content for vibration characteristics.     

Mechanical properties and water uptake of epoxy–clay nanocomposites containing different clay loadings

Nanocomposites based on diglycidyl ether of bisphenol A (DGEBA) epoxy reinforced with 1–10 wt% I.30E nanoclay were fabricated using high shear mixing technique and characterized to determine the effects of clay loading on their mechanical, thermal, and water uptake properties. The XRD and TEM analyses revealed that the structures of the resultant nanocomposites were a combination of disordered intercalated and exfoliated morphologies. Tensile strength increased for nanocomposite containing 1 % clay loading and decreased for higher nanoclay loading. Unlike strength, the stiffness increased almost linearly with clay loading, showing 46 % improvement in modulus of elasticity for nanocomposites containing 5 % of nanoclay. Water uptake measurements indicated enhancement in the barrier properties of epoxy matrix as nanoclay loading increased from 1 up to 5 wt%.     

Epoxy based nanocomposites with fully exfoliated unmodified clay: mechanical and thermal properties

The unmodified clay has been fully exfoliated in epoxy resin with the aid of a novel ultrafine full-vulcanized powdered rubber. Epoxy/rubber/clay nanocomposites with exfoliated morphology have been successfully prepared. The microstructures of the nanocomposites were characterized by means of X-ray diffraction and transmission electron microscopy. It was found that the unmodified clay was fully exfoliated and uniformly dispersed in the resulting nanocomposite. Characterizations of mechanical properties revealed that the impact strength of this special epoxy/rubber/clay nanocomposite increased up 107% over the neat epoxy resin. Thermal analyses showed that thermal stability of the nanocomposite was much better than that of epoxy nanocomposite based on organically modified clay.     

形状记忆氢化双酚A型环氧树脂的制备与性能

为研究聚丙二醇二缩水甘油醚(JH-230)对热固性形状记忆环氧树脂基本性能的影响,将异佛尔酮二胺(IPDA)与具有不同分子量比的氢化双酚A型环氧树脂(AL-3040)、聚丙二醇二缩水甘油醚(JH-230)共混,经完全固化制备出一种新型的形状记忆氢化双酚A型环氧树脂。借助傅里叶红外光谱仪(FT-IR)、差示扫描量热仪(DSC)、动态热机械分析仪(DMA)和拉伸-回复形状记忆测试分析了热固性形状记忆环氧树脂的分子结构以及JH-230对固化体系玻璃化转变温度、储能模量和形状记忆性能的影响。研究表明,JH-230可以增加固化体系链段的柔韧性;固化体系的玻璃化转变温度与动态模量随JH-230含量的增加而降低;该形状记忆氢化双酚A型环氧树脂体系具有良好的形状记忆性能,且形变完全回复时间随JH-230含量的增加而延长。     

Morphology, dynamic mechanical and thermal studies on poly(styrene-co-acrylonitrile) modified epoxy resin/glass fibre composites

Poly(styrene-co-acrylonitrile) (SAN) was used to modify diglycidyl ether of bisphenol-A (DGEBA) type epoxy resin cured with diamino diphenyl sulfone (DDS) and the modified epoxy resin was used as the matrix for fibre reinforced composites (FRPs) in order to get improved mechanical and thermal properties. E-glass fibre was used as the fibre reinforcement. The morphology, dynamic mechanical and thermal characteristics of the systems were analyzed. Morphological analysis revealed heterogeneous dispersed morphology. There was good adhesion between the matrix polymer and the glass fibre. The dynamic moduli, mechanical loss and damping behaviour as a function of temperature of the systems were studied using dynamic mechanical analysis (DMA). DMA studies showed that DDS cured epoxy resin/SAN/glass fibre composite systems have two T_gs corresponding to epoxy rich and SAN rich phases. The effect of thermoplastic modification and fibre loading on the dynamic mechanical properties of the composites were also analyzed. Thermogravimetric analysis (TGA) revealed the superior thermal stability of composite system.     

SPS制备TiNi增强镁合金复合材料的微观结构及力学性能

以AZ31镁合金为基体,TiNi形状记忆合金丝为增强体,利用放电等离子烧结法（SPS）制备了TiNi/Mg复合材料,用OM、SEM、EDS对其微观形貌进行表征,并用XRD及DSC研究TiNi丝的相变,同时对该复合材料进行准静态拉伸实验,对其室温及高温力学性能进行研究。结果表明,所制备的TiNi/Mg复合材料中界面处存在Mg、Ti、Ni元素的互扩散现象,并形成宽度约为2 μm的互扩散层;所制备的TiNi/Mg复合材料的高温力学性能高于室温,其中其屈服强度、抗拉强度及弹性模量在100℃时（分别为157 MPa,292 MPa,22 GPa）较室温分别提高了12%、33%和29%,150℃时（分别为143 MPa,251 MPa,20 GPa）较室温分别提高了2%、14%和18%。     

Mechanical and barrier properties of epoxy polymer filled with nanolayered silicate clay particles

The diglycidyl ether of bisphenol A (DGEBA) epoxy resin system filled with organo clay (OC) and unmodified clay (UC) were processed separately by two different curing agents. Triethylene tetramine (TETA) and Diaminodiphenyl methane (DDM) hardeners were used as curing agents. The nanocomposites were processed by shear mixing at different clay concentrations (1, 2, 3,5 and 10 wt%). The OC and UC were characterized by x-ray diffraction (XRD) technique. The morphology of the nanocomposites was obtained by XRD and Transmission Electron Microscopy (TEM). Bending and Impact tests conducted on these materials revealed that the organo clay filled epoxy resin showed good improvement in property over unmodified clay filled epoxy composites. The mass uptake of the nanocomposites was studied in the acid, base and water mediums. It is observed that the mass uptake in the acid medium is higher than in other mediums. The equilibrium mass uptake in all the mediums for nanocomposites was found to be lower compared to neat epoxy polymer system.     

The effect of alternate heating rates during cure on the structure-property relationships of epoxy/MMT clay nanocomposites

This paper investigates the effect of both the mixing technique and heating rate during cure on the dispersion of montmorillonite (MMT) clay in an epoxy resin. The combination of sonication and using a 10 °C/min heating rate during cure was found to facilitate the dispersion of nanoclay in epoxy resin. These processing conditions provided a synergistic effect, making it possible for polymer chains to penetrate in-between clay galleries and detach platelets from their agglomerates. As the degree of dispersion was enhanced, the flexural modulus and strength properties were found to decrease by 15% and 40%, respectively. This is thought to be due to individual platelets fracturing in the nanocomposite. Complementary techniques including X-ray diffraction (XRD), small angle X-ray scattering (SAXS), scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDX), transmission electron microscopy (TEM) and optical microscopy were essential to fully characterise localised and spatial regions of the clay morphologies.     

Preparation,microstructure and thermal mechanical properties of epoxy/crude clay nanocomposites

To improve the performance/cost ratio of epoxy/clay nanocomposites, epoxy resin was reinforced with crude clay with the help of a silane modifier. The epoxy/crude clay nanocomposites were produced through a recently developed “slurry compounding” approach. The microstructure of the nanocomposites was characterized with X-ray diffraction (XRD), optical microscopy and transmission electron microscopy (TEM). The thermal mechanical properties were studied with dynamic mechanical analysis (DMA) and thermogravimetric analysis (TGA). It has been shown that only 5 wt% of silane modifier is required to facilitate the dispersion and exfoliation of crude clay in epoxy matrix. The storage moduli and thermal stability were improved with the addition of crude clay.     

环氧树脂/粘土纳米复合材料的制备与性能研究

研究了有机蒙脱土在环氧树脂中的插层和剥离行为,制备了两种环氧树脂/蒙脱土纳米复合材料并测试了其力学性能。实验结果表明,环氧树脂与有机土的相容性好,二者混合时环氧树脂很容易插入到粘土层间。使用经不同有机阳离子处理的两种有机蒙脱土,分别制得插层型和剥离型环氧/粘土纳米复合材料,力学性能结果表明,剥离型纳米复合材料的性能优于同组成的插层型纳米复合材料。     

Effect of phase on debond strength in shape memory alloy reinforced composites

Systematic single fiber pullout tests were performed on epoxy composites embedded with nickel titanium shape memory alloy (SMA) wires. The SMA wires were tested in the austenitic or martensitic states to study and decouple the elastic moduli from martensite transformation or reorientation stresses in the analysis of debond loads. The results reveal that the SMA wires that were in the austenite phase consistently produced higher debond loads as compared to that of those wires that started in the martensite phase, likely due to differences in the Poisson’s ratio. Additionally, there appears to be a relationship between the elastic modulus and debond load where reinforcements with a higher elastic modulus displayed lower debond loads. Lastly, for SMA reinforcements that underwent a martensitic phase transformation or reorientation, the debond load was equivalent to the martensite transformation or reorientation load. The results of this work illustrate the sensitivity of SMA reinforced composites on the mechanical behavior and phase transformation characteristics of the constituent materials.     

Mechanical Properties and Interlaminar Fracture Toughness of Glass‐Fiber‐Reinforced Epoxy Composites Embedded with Shape Memory Alloy Wires

The effects of the content and position of shape memory alloy (SMA) wires on the mechanical properties and interlaminar fracture toughness of glass‐fiber‐reinforced epoxy (GF/epoxy) composite laminates are investigated. For this purpose, varying numbers of SMA wires are embedded in GF/epoxy composite laminates in different stacking sequences. The specimens are prepared by vacuum‐assisted resin infusion (VARI) processing and are subjected to static tensile and three‐point‐bending tests. The results show that specimens with two SMA wires in the stacking sequence of [GF₂/SMA/GF₁/SMA/GF₂] and four SMA wires in the stacking sequence of [GF₄/SMA/GF₂/SMA/GF₄] exhibit optimal performance. The flexural strength of the optimal four‐SMA‐wire composite is lower than that of the pure GF/epoxy composite by 5.76% on average, and the flexural modulus is improved by 5.19%. Mode‐I and II interlaminar fracture toughness tests using the SMA/GF/epoxy composite laminates in the stacking sequence of [GF₄/SMA/GF₂/SMA/GF₄] are conducted to evaluate the mechanism responsible for decreasing the mechanical properties. Scanning electron microscopy (SEM) observations reveal that the main damage modes are matrix delamination, interfacial debonding, and fiber pullout.

     

Enhanced Mechanical Properties of Epoxy Nanocomposites by Mixing Noncovalently Functionalized Boron Nitride Nanoflakes

The influence of surface modifications on the mechanical properties of epoxy‐hexagonal boron nitride nanoflake (BNNF) nanocomposites is investigated. Homogeneous distributions of boron nitride nanoflakes in a polymer matrix, preserving intrinsic material properties of boron nitride nanoflakes, is the key to successful composite applications. Here, a method is suggested to obtain noncovalently functionalized BNNFs with 1‐pyrenebutyric acid (PBA) molecules and to synthesize epoxy–BNNF nanocomposites with enhanced mechanical properties. The incorporation of noncovalently functionalized BNNFs into epoxy resin yields an elastic modulus of 3.34 GPa, and 71.9 MPa ultimate tensile strength at 0.3 wt%. The toughening enhancement is as high as 107% compared to the value of neat epoxy. The creep strain and the creep compliance of the noncovalently functionalized BNNF nanocomposite is significantly less than the neat epoxy and the nonfunctionalized BNNF nanocomposite. Noncovalent functionalization of BNNFs is effective to increase mechanical properties by strong affinity between the fillers and the matrix.     

The effects of alumina nanofillers on mechanical properties of high-performance epoxy resin

In the past decade extensive studies have been focused on mechanical properties of inorganic nanofiller/epoxy matrices. In this work we systematically investigated the mechanical properties of nano-alumina-filled E-54/4, 4-diaminodiphenylsulphone (DDS) epoxy resins, which were prepared via combining high-speed mixing with three-roll milling. Homogeneous dispersion of nano-alumina with small agglomerates was obtained in epoxy resin, which was confirmed using transmission electron microscopy (TEM). The static/dynamic modulus, tensile strength and fracture toughness of the nanocomposites were found to be simultaneously enhanced with addition of nano-alumina fillers. About 50% and 80% increases of K(IC) and G(IC) were achieved in nanocomposite filled with 18.4 wt% alumina nanofillers, as compared to that of the unfilled epoxy resin. Furthermore, the corresponding fracture surfaces of tensile and compact tension samples were examined by scanning electron microscopy (SEM) and atomic force microscopy (AFM) techniques in order to identify the relevant fracture mechanisms involved. Various fracture features including cavities/debonding of nanofiller, local plastic deformation as well as crack pinning/deflection were found to be operative in the presence of nano-alumina fillers.     

Mode I interlaminar fracture behavior and mechanical properties of CFRPs with nanoclay-filled epoxy matrix

The mechanical properties and fracture behavior of nanocomposites and carbon fiber composites (CFRPs) containing organoclay in the epoxy matrix have been investigated. Morphological studies using TEM and XRD revealed that the clay particles within the epoxy resin were intercalated or orderly exfoliated. The organoclay brought about a significant improvement in flexural modulus, especially in the first few wt% of loading, and the improvement of flexural modulus was at the expense of a reduction in flexural strength. The quasi-static fracture toughness increased, whereas the impact fracture toughness dropped sharply with increasing the clay content.Flexural properties of CFRPs containing organoclay modified epoxy matrix generally followed the trend similar to the epoxy nanocomposite although the variation was much smaller for the CFRPs. Both the initiation and propagation values of mode I interlaminar fracture toughness of CFRP composites increased with increasing clay concentration. In particular, the propagation fracture toughness almost doubled with 7 wt% clay loading. A strong correlation was established between the fracture toughness of organoclay-modified epoxy matrix and the CFRP composite interlaminar fracture toughness.     

Effect of processing parameters and clay volume fraction on the mechanical properties of epoxy-clay nanocomposites

The influence of processing parameters and particle volume fraction was experimentally studied for epoxy clay nanocomposites. Nanocomposites were prepared using onium ion surface modified montmorillonite (MMT) layered clay and epoxy resin (DEGBF). Two different techniques were used for dispersing the clay particles in the epoxy matrix, viz. high-speed shear dispersion and ultrasonic disruption. The volume fraction of clay particles was systematically varied from 0.5 to 6%, and mechanical properties, viz. flexural modulus and fracture toughness, were studied as a function of clay volume fraction and the processing technique. The flexural modulus was observed to increase monotonously with increase in volume fraction of clay particles, while, the fracture toughness showed an initial increase on addition of clay particles, but a subsequent decrease at higher clay volume fractions. In general, nanocomposites processed by shear mixing exhibited better mechanical properties as compared to those processed by ultrasonication. Investigation by X-ray diffraction (XRD) revealed exfoliated clay structure in most of the nanocomposites that were fabricated. Morphologies of the fracture surfaces of nanocomposites were studied using a scanning electron microscopy (SEM). Presence of river markings at low clay volume fractions provided evidence of extrinsic toughening taking place in an otherwise brittle epoxy.     

Thermal, mechanical and vibration characteristics of epoxy-clay nanocomposites

Diglycidyl ether of bisphenol-A (DGEBA) epoxy resin system filled individually with organoclay (OC) and unmodified clay (UC) were synthesized by mechanical shear mixing with the addition of diamino-diphenylmethane (DDM) hardener. The unmodified clay used was Na⁺-Montmorillonite (MMT) and the organoclay was alkyl ammonium treated MMT clay. The reinforcement effect of OC and UC in the epoxy polymer on thermal, mechanical and vibration properties were studied. X-ray diffraction (XRD) and Transmission electron microscopy (TEM) were used to study the structure and morphology of nanocomposites. Curing study shows that the addition of OC in epoxy resin aids the polymerization by catalytic effect, and UC addition does not show any effect in the curing behavior of epoxy polymer. Thermogravimetry analysis (TGA) shows enhanced thermal stability for epoxy with OC fillers than that of epoxy with UC fillers. The epoxy with OC fillers shows considerable improvement on tensile and impact properties over pure epoxy polymer and epoxy with UC fillers. The improvement in tensile and impact properties of nanocomposites is supported with the fracture surface studies. Epoxy with OC fillers shows enhanced vibration characteristics than that of the pure epoxy polymer and epoxy with UC fillers.