拉压弹性模量差异对泡沫铝夹芯板三点弯曲模拟的影响

泡沫铝材料是一种典型的拉压双模量材料,即受拉与受压时弹性模量不同。使用ABAQUS有限元软件对泡沫铝夹芯板的三点弯曲行为进行了模拟。首先,对泡沫铝芯层采用可压缩泡沫模型,通过对芯层的受拉区和受压区采用不同的弹性模量来讨论拉压弹性模量差异对夹芯板三点弯曲行为的影响。同时,在泡沫铝压缩响应一致的情况下,对可反映拉压弹性模量差异的孔洞模型和未考虑拉压弹性模量差异的可压缩泡沫模型的夹芯板三点弯曲模拟结果进行了比较。研究表明,泡沫铝芯层的弹性模量对夹芯板的三点弯曲行为模拟有较大影响。若不考虑泡沫铝拉压弹性模量的差异,得到的夹芯板三点弯曲情况下的加载刚度和屈服荷载明显偏低。     

拉压弹性模量差异对泡沫铝夹芯板三点弯曲模拟的影响

泡沫铝材料是一种典型的拉压双模量材料,即受拉与受压时弹性模量不同。使用ABAQUS有限元软件对泡沫铝夹芯板的三点弯曲行为进行了模拟。首先,对泡沫铝芯层采用可压缩泡沫模型,通过对芯层的受拉区和受压区采用不同的弹性模量来讨论拉压弹性模量差异对夹芯板三点弯曲行为的影响。同时,在泡沫铝压缩响应一致的情况下,对可反映拉压弹性模量差异的孔洞模型和未考虑拉压弹性模量差异的可压缩泡沫模型的夹芯板三点弯曲模拟结果进行了比较。研究表明,泡沫铝芯层的弹性模量对夹芯板的三点弯曲行为模拟有较大影响。若不考虑泡沫铝拉压弹性模量的差异,得到的夹芯板三点弯曲情况下的加载刚度和屈服荷载明显偏低。     

泡沫铝夹芯板压入和侵彻性能的实验研究

利用MTS和落锤试验机研究了由复合材料面板和闭孔泡沫铝芯层组成的夹芯板结构在压入和侵彻时的变形和失效行为,并通过引入无量纲参数——能量吸收效率因子,探讨了一些关键参数对夹芯板压入和侵彻性能以及能量吸收性能的影响,如冲击能量、面板厚度、芯层厚度及相对密度、压头/锤头形状和边界条件等。结果表明夹芯板的破坏主要集中在压头作用的局部区域内。夹芯板的能量吸收效率对其结构参数比较敏感,增加上层面板厚度、芯层厚度或芯层相对密度能够有效地提高夹芯板结构的能量吸收能力以及抵抗压入和侵彻的能力,而下层面板厚度的对夹心板抗侵彻性能的影响不明显。不同的压头/锤头形状和边界条件对泡沫铝夹芯板的压入和侵彻响应以及能量吸收性能影响明显。     

碳纤维复合材料-泡沫铝夹芯板的冲击响应

采用泡沫金属子弹撞击加载的方式研究了T700碳纤维复合材料面层-泡沫铝芯体的夹芯结构动力响应。利用激光测速装置、高速摄像仪和位移传感器记录了泡沫子弹的撞击速度、子弹撞击夹芯板全过程和夹芯板后面板中心点的位移时程曲线。研究了加载冲量和芯层相对密度对夹芯板冲击响应的影响,得到了碳纤维复合材料-泡沫铝夹芯板的变形与失效模式。同时,采用ABAQUS有限元软件进行数值模拟,研究了复合材料面板铺层方式、面层厚度、芯层厚度和相对密度以及泡沫铝子弹的长度、速度和相对密度等参数对夹芯板冲击响应的影响。     

泡沫金属子弹撞击载荷下多孔金属夹芯板的动态响应

应用泡沫金属子弹撞击加载的方式研究了固支多孔金属夹芯板的塑性动力响应。讨论了多孔金属夹芯板在冲击载荷作用下的破坏模式。结果表明夹芯板的破坏主要表现在前面板的压痕与侵彻失效,芯层压缩和芯层剪切破坏。基于实验研究,应用LS-DYNA 3D非线性动力学有限元分析软件对夹芯板动力响应进行了有限元分析。数值研究结果与实验结果吻合较好。考察了加载冲量、面板厚度、芯层厚度及相对密度对多孔金属夹芯板抗撞击性能的影响。夹芯板的结构响应对其结构配置比较敏感,增加面板厚度或芯层厚度能够明显地减小后面板的挠度,提高夹芯板的抗撞击能力。研究结果对多孔金属夹芯板的优化设计具有一定得参考价值。     

Kevlar短纤维增韧碳纤维/铝蜂窝夹芯板三点弯曲与面内压缩性能

介绍了碳纤维/铝蜂窝夹芯结构的Kevlar短纤维界面增韧方法。通过三点弯曲实验和面内压缩实验,对比增韧试件与未增韧试件的载荷位移曲线、破坏模式等特征,发现未增韧试件往往先发生界面分层破坏,继而面板和芯体分别发生局部破坏;而增韧试件通常发生整体破坏。实验数据显示,Kevlar短纤维界面增韧可以使碳纤维/铝蜂窝夹芯板的抗弯强度、压缩强度、能量吸收等力学性能分别至少提高14.06%、55.80%和61.53%。对破坏后界面的SEM观测发现:增韧试件并未发生界面脱粘,而是由于芯体撕裂造成面/芯剥离,揭示了Kevlar短纤维的界面增韧机制。对具有Kevlar短纤维界面增韧的碳纤维/铝蜂窝夹芯结构进行有限元建模,并分别对其在三点弯曲和面内压缩载荷下的力学行为进行数值分析,以指导该类夹芯结构的分析与设计。     

钢板夹泡沫铝组合板抗爆性能数值模拟

鉴于泡沫铝材料良好的吸能特性和三明治型组合构件在强度、刚度上的优势,通过有限元分析软件ANSYS/LS-DYNA对钢板-泡沫铝-钢板三明治型组合板进行了装药量为10.0kgTNT的非接触爆炸数值模拟,考察组合板在爆炸荷载作用下的动力响应。研究表明:钢板夹泡沫铝组合板承受爆炸冲击波荷载时,响应方式主要为组合板整体弯曲变形和泡沫铝芯层局部压缩变形,芯层压缩变形是组合板吸收耗散能量的主要途径;适当地增加泡沫铝芯层厚度和面板厚度能够提高组合板的抗爆性能,同时使组合板充分发挥耗能作用。     

钢板夹泡沫铝组合板抗爆性能数值模拟

鉴于泡沫铝材料良好的吸能特性和三明治型组合构件在强度、刚度上的优势,通过有限元分析软件ANSYS/LS-DYNA对钢板-泡沫铝-钢板三明治型组合板进行了装药量为10.0kgTNT的非接触爆炸数值模拟,考察组合板在爆炸荷载作用下的动力响应。研究表明:钢板夹泡沫铝组合板承受爆炸冲击波荷载时,响应方式主要为组合板整体弯曲变形和泡沫铝芯层局部压缩变形,芯层压缩变形是组合板吸收耗散能量的主要途径;适当地增加泡沫铝芯层厚度和面板厚度能够提高组合板的抗爆性能,同时使组合板充分发挥耗能作用。     

泡沫铝夹芯板抗冲击性能分析

试验设计了3块钢板夹泡沫铝夹芯板,厚度分别为50 mm、70 mm和100 mm。对每种厚度夹芯板进行七组不同落锤高度的冲击试验,测得了上、下面板变形值,记录了夹芯板的破坏情况。应用数值模拟软件ANSYS/LS-DYNA进一步还原夹芯板冲击过程,导出了面板与芯材的吸能占比。基于假设的夹芯板理论模型,给出了平均冲击荷载、局部变形和整体变形最大值的估算公式。结果表明:当夹芯板尺寸和材料强度一定时,局部变形值与落锤高度的平方根成正比,整体变形最大值、平均冲击力均与落锤高度的平方根成线性关系。夹芯板的抗冲击性能主要依靠增大泡沫铝芯层的变形进行耗能,芯层越厚,泡沫铝吸能占比越大,局部变形越小,夹芯板受到的冲击力越大。     

蜂窝金属夹芯板重复冲击动态响应研究

蜂窝金属及其夹芯结构是一种物理功能与结构一体化的新型轻质高强结构,广泛应用于结构轻量化与碰撞冲击防护领域。采用ABAQUS非线性有限元软件建立了蜂窝金属夹芯板(honeycomb sandwich panel,HSP)结构动态冲击数值仿真模型,数值仿真计算结果与文献实验结果吻合较好,验证了数值仿真模型的正确性。在此基础上,开展了重复冲击载荷作用下蜂窝金属夹芯板结构动态响应研究,得到了重复冲击力时程曲线、动态变形时程曲线、冲击力位移曲线以及最终挠度,分析了冲击能量、蜂窝壁厚以及上、下面板厚度分配对蜂窝金属夹芯板结构重复冲击动态响应的影响规律。研究结果表明,重复冲击载荷作用下蜂窝金属夹芯板结构上、下面板弯曲变形以及蜂窝芯层压缩变形逐渐积累,蜂窝芯层薄壁结构逐渐达到密实化,结构抗弯刚度逐渐上升,变形增量逐渐减小,结构整体能量吸收率下降。通过调节蜂窝壁厚和上、下面板厚度分配可以显著调节蜂窝金属夹芯板结构重复冲击动态响应与能量吸收性能。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...