A 2.5-Gb/s 15-mW clock recovery circuit

This paper describes the design of a 2.5-Gb/s 15-mW clock recovery circuit based on the quadricorrelator architecture. Employing both phase and frequency detection, the circuit combines high-speed operations such as differentiation, full-wave rectification, and mixing in one stage to lower the power dissipation. In addition, a two-stage voltage-controlled oscillator is utilized that incorporates both phase shift elements to provide a wide tuning range and isolation techniques to suppress the feedthrough due to input data transitions. Fabricated in a 20-GHz 1-μm BiCMOS technology, the circuit exhibits an rms jitter of 9.5 ps and a capture range of 300 MHz     

A 4-Gb/s CMOS clock and data recovery circuit using 1/8-rate clock technique

A 4-Gb/s clock and data recovery (CDR) circuit is realized in a 0.25-/spl mu/m standard CMOS technology. The CDR circuit exploits 1/8-rate clock technique to facilitate the design of a voltage-controlled oscillator (VCO) and to eliminate the need of 1:4 demultiplexer, thereby achieving low power consumption. The VCO incorporates the ring oscillator configuration with active inductor loads, generating four half-quadrature clocks. The VCO control line comprises both a programmable 6-bit digital coarse control and a folded differential fine control through a charge-pump and a low pass filter. Duty-cycle correction of clock signals is obtained by exploiting a high common-mode rejection ratio differential amplifier at the ring oscillator output. A 1/8-rate linear phase detector accomplishes the phase error detection with no systematic phase offset and inherently performs the 1:4 demultiplexing. Test chips demonstrate the jitter of the recovered clock to be 5.2 ps rms and 47 ps pk-pk for 2/sup 31/-1 pseudorandom bit sequence (PRBS) input data. The phase noise is measured to be -112 dBc/Hz at 1-MHz offset. The measured bit error rate is less than 10/sup -6/ for 2/sup 31/-1 PRBS. The chip excluding output buffers dissipates 70 mW from a single 2.5-V supply.     

A 14-mW 6.25-Gb/s Transceiver in 90-nm CMOS

This paper describes a 6.25-Gb/s 14-mW transceiver in 90-nm CMOS for chip-to-chip applications. The transceiver employs a number of features for reducing power consumption, including a shared LC-PLL clock multiplier, an inductor-loaded resonant clock distribution network, a low- and programmable-swing voltage-mode transmitter, software-controlled clock and data recovery (CDR) and adaptive equalization within the receiver, and a novel PLL-based phase rotator for the CDR. The design can operate with channel attenuation of -15 dB or greater at a bit-error rate of 10^-15 or less, while consuming less than 2.25 mW/Gb/s per transceiver.     

A CMOS clock recovery circuit for 2.5-Gb/s NRZ data

This paper describes a phase-locked clock recovery circuit that operates at 2.5 Gb/s in a 0.4-μm digital CMOS technology. To achieve a high speed with low power dissipation, a two-stage ring oscillator is introduced that employs an excess phase technique to operate reliably across a wide range. A sample-and-hold phase detector is also described that combines the advantages of linear and nonlinear phase detectors. The recovered clock exhibits an rms jitter of 10.8 ps for a PRBS sequence of length 2⁷-1 and a phase noise of -80 dBc/Hz at a 5-MHz offset. The core circuit dissipates a total power of 33.5 mW from a 3.3-V supply and occupies an area of 0.8×0.4 mm²     

A 26-Gb/s CMOS optical receiver with a reference-less CDR in 65-nm CMOS

This paper presents a 26-Gb/s CMOS optical receiver that is fabricated in 65-nm technology. It consists of a triple-inductive transimpedance amplifier (TIA), direct current (DC) offset cancellation circuits, 3-stage gm-TIA variable-gain amplifiers (VGA), and a reference-less clock and data recovery (CDR) circuit with built-in equalization technique. The TIA/VGA front-end measurement results demonstrate 72-dBΩ transimpedance gain, 20.4-GHz −3-dB bandwidth, and 12-dB DC gain tuning range. The measurements of the VGA’s resistive networks also demonstrate its efficient capability of overcoming the voltage and temperature variations. The CDR adopts a full-rate topology with 12-dB imbedded equalization tuning range. Optical measurements of this chipset achieve a 10⁻¹² BER at 26 Gb/s for a 2¹⁵−1 PRBS input with a −7.3-dBm input sensitivity. The measurement results with a 10-dB @ 13 GHz attenuator also demonstrate the effectiveness of the gain tuning capability and the built-in equalization. The entire system consumes 140 mW from a 1/1.2-V supply.     

5-Gb/s 0.18-μm CMOS集成时钟提取功能的2:1复接器设计

摘要：采用SMIC 0.18um CMOS工艺设计并实现了一个5-Gb/s在片集成时钟提取功能的2:1复接器,且该时钟提取子电路具有自动相位对准功能.芯片面积为670um*780um.在1.8V电压下,总功耗为112 mW, 输入灵敏度在50 mV以下, 输出单端摆幅大于300 mV. 测试结果表明,该复接器能够在不需要任何外接元件、参考时钟或外部相位调整下可靠地工作在1.8 Gb/s至2.6 Gb/s之间的任何输入数据速率. 该芯片可被用在并行光互连系统中.     

A monolithic 2.3-Gb/s 100-mW clock and data recovery circuit insilicon bipolar technology

A monolithic clock and data recovery PLL circuit is implemented in a digital silicon bipolar technology without modification. The only external component used is the loop filter capacitor. A self-aligned data recovery architecture combined with a novel phase-detector design eliminates the need for nonlinear processing and phase shifter stages. This enables a simpler design with low power and reduced dependence on the bit rate. At 2.3 Gb/s, the test chip consumes 100 mW from a -3.6-V supply, excluding the input and output buffers. The worst-case rms jitter of the recovered clock is less than 14 ps with 2²³-1 pseudorandom bit sequence     

2.8-Gb/s 176-mW byte-interleaved and 3.0-Gb/s 118-mWbit-interleaved 8:1 multiplexers with a 0.15-μm CMOS technology

This paper reports the first CMOS implementation of an 8:1 byte-interleaved multiplexer (byte-MUX) operating in the Gb/s region, together with an 8:1 bit-interleaved multiplexer (bit-MUX). A future generation 0.15-μm CMOS technology has been applied. Both chips use identical bit-MUX cores with a static shift-register architecture, and have ECL interfaces with a single supply of -2 V. The byte-MUX demonstrates 43-mW/GHz dependence on clock frequency and operates up to 2.8 Gb/s with a power dissipation of 176 mW. The bit-MUX showed 20-mW/GHz dependence on clock frequency and operated up to 3.0 Gb/s with a power dissipation of 118 mW. This revel of performance has been achieved by a novel row-column exchanger configuration, critical path reduction and precise clocking techniques utilized in the bit-MUX core, and the development of high-speed I/O buffers     

A 10-Gb/s CMOS CDR and DEMUX IC With a Quarter-Rate Linear Phase Detector

This paper presents a 10-Gb/s clock and data recovery (CDR) and demultiplexer IC in a 0.13-mum CMOS process. The CDR uses a new quarter-rate linear phase detector, a new data recovery circuit, and a four-phase 2.5-GHz LC quadrature voltage-controlled oscillator for both wide phase error pulses and low power consumption. The chip consumes 100 mA from a 1.2-V core supply and 205 mA from a 2.5-V I/O supply including 18 preamplifiers and low voltage differential signal (LVDS) drivers. When 9.95328-Gb/s 2³¹-1 pseudorandom binary sequence is used, the measured bit-error rate is better than 10^-15 and the jitter tolerance is 0.5UIpp, which exceeds the SONET OC-192 standard. The jitter of the recovered clock is 2.1 psrms at a 155.52MHz monitoring clock pin. Multiple bit rates are supported from 9.4 Gb/s to 11.3 Gb/s     

A 150-MS/s 8-b 71-mW CMOS time-interleaved ADC

A pipelined analog-to-digital converter (ADC) architecture suitable for high-speed (150 MHz), Nyquist-rate A/D conversion is presented. At the input of the converter, two parallel track-and-hold circuits are used to separately drive the sub-ADC of a 2.8-b first pipeline stage and the input to two time-interleaved residue generation paths. Beyond the first pipeline stage, each residue path includes a cascade of two 1.5-b pipeline stages followed by a 4-b "backend" folding ADC. The full-scale residue range at the output of the pipeline stages is half that of the converter input range in order to conserve power in the operational amplifiers used in each residue path. An experimental prototype of the proposed ADC has been integrated in a 0.18-/spl mu/m CMOS technology and operates from a 1.8-V supply. At a sampling rate of 150 MSample/s, it achieves a peak SNDR of 45.4 dB for an input frequency of 80 MHz. The power dissipation is 71 mW.     

具有时钟提取及倍频功能的 5Gb/s全速率复接器设计

采用SMIC 0．18μm CMOS工艺设计了一个具有时钟提取及倍频功能的5Gb／s全速率2：1复接电路。整个电路由两部分构成,即：全速率2：1复接器和时钟提取及倍频环路。其中,后者从一路2．5Gb／S输入数据中提取出时钟信号,并为前者提供所需的2．5GHz及5GHz的时钟。Pottbgcker鉴频鉴相器被运用以提高环路的捕获带宽。设计广泛采用了具有速度高和抗干扰能力强等诸多优点的电流模逻辑。仿真结果表明,本电路无需任何参考时钟,无需外接元件及手动相位调整或辅助捕获,就能可靠地工作在2．4～2．9Gb／s的输入数据速率上。芯片面积为812μm×675μm。电源电压1．8V时,功耗为162mW。     

A 10-Gb/s CMOS clock and data recovery circuit with a half-ratelinear phase detector

A 10-Gb/s phase-locked clock and data recovery circuit incorporates an interpolating voltage-controlled oscillator and a half-rate phase detector. The phase detector provides a linear characteristic while retiming and demultiplexing the data with no systematic phase offset. Fabricated in a 0.18-μm CMOS technology in an area of 1.1×0.9 mm², the circuit exhibits an RMS jitter of 1 ps, a peak-to-peak jitter of 14.5 ps in the recovered clock, and a bit-error rate of 1.28×10^-6, with random data input of length 2²³-1. The power dissipation is 72 mW from a 2.5-V supply     

A 50-Gb/s 10-mW Analog Equalizer Using Transformer Feedback Technique in 65-nm CMOS Technology

A 50-Gb/s low-power analog equalizer has been realized in 65-nm CMOS technology. This equalizer adopts the proposed transformer feedback technique to achieve a peaking gain of 18 dB at 25 GHz and low-power dissipation. The whole equalizer without the output buffer consumes 10 mW from a 1-V supply. The chip occupies 0.35 times 0.27 mm². For a 50-Gb/s pseudorandom bit sequence of 2⁷ - 1 , the measured bit error rate is less than 10^-12, and the measured maximum root-mean-square and peak-to-peak jitters are 2.7 and 12.4 ps, respectively.     

A CMOS multichannel 10-Gb/s transceiver

We describe a CMOS multichannel transceiver that transmits and receives 10 Gb/s per channel over balanced copper media. The transceiver consists of two identical 10-Gb/s modules. Each module operates off a single 1.2-V supply and has a single 5-GHz phase-locked loop to supply a reference clock to two transmitter (Tx) channels and two receiver (Rx) channels. To track the input-signal phase, the Rx channel has a clock recovery unit (CRU), which uses a phase-interpolator-based timing generator and digital loop filter. The CRU can adjust the recovered clock phase with a resolution of 1.56 ps. Two sets of two-channel transceiver units were fabricated in 0.11-/spl mu/m CMOS on a single test chip. The transceiver unit size was 1.6 mm /spl times/ 2.6 mm. The Rx sensitivity was 120-mVp-p differential with a 70-ps phase margin for a common-mode voltage ranging from 0.6 to 1.0 V. The evaluated jitter tolerance curve met the OC-192 specification.     

A 1.8-V 10-Gb/s fully integrated CMOS optical receiver analog front-end

A fully integrated 10-Gb/s optical receiver analog front-end (AFE) design that includes a transimpedance amplifier (TIA) and a limiting amplifier (LA) is demonstrated to require less chip area and is suitable for both low-cost and low-voltage applications. The AFE is fabricated using a 0.18-/spl mu/m CMOS technology. The tiny photo current received by the receiver AFE is amplified to a differential voltage swing of 400 mV/sub (pp)/. In order to avoid off-chip noise interference, the TIA and LA are dc-coupled on the chip instead of ac-coupled though a large external capacitor. The receiver front-end provides a conversion gain of up to 87 dB/spl Omega/ and -3dB bandwidth of 7.6 GHz. The measured sensitivity of the optical receiver is -12dBm at a bit-error rate of 10/sup -12/ with a 2/sup 31/-1 pseudorandom test pattern. Three-dimensional symmetric transformers are utilized in the AFE design for bandwidth enhancement. Operating under a 1.8-V supply, the power dissipation is 210 mW, and the chip size is 1028 /spl mu/m/spl times/1796 /spl mu/m.     

A 70-MS/s 110-mW 8-b CMOS folding and interpolating A/D converter

A CMOS analog to digital converter based on the folding and interpolating technique is presented. This technique is successfully applied in bipolar A/D converters and now also becomes available in CMOS technology. The analog bandwidth of the A/D converter is increased by using a transresistance amplifier at the outputs of the folding amplifiers and, due to careful circuit design, the comparators need no offset compensation. The result is a small area (0.7 mm² in 0.8 μm CMOS), high speed (70 MS/s), and low-power (110 mW at 5 V supply, including reference ladder) A/D converter. A 3.3 V supply version of the circuit runs at 45 MS/s and dissipates 45 mW     

A 6.0-mW 10.0-Gb/s Receiver With Switched-Capacitor Summation DFE

A low-power receiver with a one-tap decision feedback equalization (DFE) was fabricated in 90-nm CMOS technology. The speculative equalization is performed using switched-capacitor-based addition at the front-end sample-hold circuit. In order to further reduce the power consumption, an analog multiplexer is used in the speculation technique implementation. A quarter-rate-clocking scheme facilitates the use of low-power front-end circuitry and CMOS clock buffers. The receiver was tested over channels with different levels of ISI. The signaling rate with BER<10^-12 was significantly increased with the use of DFE for short- to medium-distance PCB traces. At 10-Gb/s data rate, the receiver consumes less than 6.0 mW from a 1.0-V supply. This includes the power consumed in all quarter-rate clock buffers, but not the power of a clock recovery loop. The input clock phase and the DFE taps are adjusted externally     

A 10-Gb/s CMOS clock and data recovery circuit with a half-rate binary phase/frequency detector

A 10-Gb/s phase-locked clock and data recovery circuit incorporates a multiphase LC oscillator and a half-rate phase/frequency detector with automatic data retiming. Fabricated in 0.18-/spl mu/m CMOS technology in an area of 1.75/spl times/1.55 mm/sup 2/, the circuit exhibits a capture range of 1.43 GHz, an rms jitter of 0.8 ps, a peak-to-peak jitter of 9.9 ps, and a bit error rate of 10/sup -9/ with a pseudorandom bit sequence of 2/sup 23/-1. The power dissipation excluding the output buffers is 91 mW from a 1.8-V supply.     

A 40-Gb/s clock and data recovery circuit in 0.18-/spl mu/m CMOS technology

A phase-locked clock and data recovery circuit incorporates a multiphase LC oscillator and a quarter-rate bang-bang phase detector. The oscillator is based on differential excitation of a closed-loop transmission line at evenly spaced points, providing half-quadrature phases. The phase detector employs eight flip-flops to sample the input every 12.5 ps, detecting data transitions while retiming and demultiplexing the data into four 10-Gb/s outputs. Fabricated in 0.18-/spl mu/m CMOS technology, the circuit produces a clock jitter of 0.9 ps/sub rms/ and 9.67 ps/sub pp/ with a PRBS of 2/sup 31/-1 while consuming 144 mW from a 2-V supply.     

A 10-Gb/s CDR/DEMUX with LC delay line VCO in 0.18-/spl mu/m CMOS

A monolithic 10-Gb/s clock/data recovery and 1:2 demultiplexer are implemented in 0.18-/spl mu/m CMOS. The quadrature LC delay line oscillator has a tuning range of 125 MHz and a 60-MHz/V sensitivity to power supply pulling. The circuit meets SONET OC-192 jitter specifications with a measured jitter of 8 ps p-p when performing error-free recovery of PRBS 2/sup 31/-1 data. Clock and data recovery (CDR) is achieved at 10 Gb/s, demonstrating the feasibility of a half-rate early/late PD (with tri-state) based CDR on 0.18-/spl mu/m CMOS. The 1.9/spl times/1.5 mm/sup 2/ IC (not including output buffers) consumes 285 mW from a 1.8-V supply.