Transmit beamforming and power control for cellular wirelesssystems

Joint power control and beamforming schemes are proposed for cellular systems where adaptive arrays are used only at base stations. In the uplink, mobile power and receiver diversity combining vectors at the base stations are calculated jointly. The mobile transmitted power is minimized, while the signal-to-interference-and-noise ratio (SINR) at each link is maintained above a threshold. A transmit diversity scheme for the downlink is also proposed where the transmit weight vectors and downlink power allocations are jointly calculated such that the SINR at each mobile is above a target value. The proposed algorithm achieves a feasible solution for the downlink if there is one and minimizes the total transmitted power in the network. In a reciprocal network it can be implemented in a decentralized system, and it does not require global channel response measurements. In a nonreciprocal network, where the uplink and downlink channel responses are different, the proposed transmit beamforming algorithm needs to be implemented in a centralized system, and it requires a knowledge of the downlink channel responses. The performances of these algorithms are compared with previously proposed algorithms through numerical studies     

Joint beamforming and power control in downlink multiuser multiple‐input multiple‐output systems

In this paper, we study joint beamforming and power control for downlink multiple‐input multiple‐output systems with multiple users and target values for signal‐to‐interference plus noise ratios (SINRs). We formulate this as a constrained optimization problem of minimizing total interference subject to constraints on the beamforming vector norms, target SINRs, and total transmit power. Necessary and sufficient conditions satisfied by the optimal beamformer and power allocation are presented, and a new algorithm for joint beamforming and power control is proposed. This adapts the beamforming vectors and transmit powers incrementally, and it stops when the specified SINR targets are achieved with minimum powers. The proposed algorithm is illustrated with numerical results obtained from simulations, which study its convergence and compare it with other similar algorithms. Copyright © 2013 John Wiley & Sons, Ltd.     

Joint hybrid beamforming and power splitting design in millimeter-wave simultaneous wireless information and power transfer system

A joint hybrid beamforming and power splitting(JHBPS) design problem for simultaneous wireless information and power transfer(SWIPT) in millimeter-wave(mmWave) system is studied.The considered scenario is a multi-antenna base station(BS) transfers information and energy simultaneously to multiple single-antenna receivers.BS adopts hybrid digital and analog beamforming architecture to reduce hardware costs.Receivers separate acquired signals with power splitters either for information decoding(ID) or energy harvesting(EH).The aim is minimizing total transmission power by joint design of hybrid beamforming and PS under ID and EH requirements.It is difficult to obtain the optimal hybrid beamformer directly since the analog beamformer and digital beamformer are multiplied.Therefore,a two-stage algorithm is proposed to solve the problem.In the first stage,the optimal beamformer and PS ratios are obtained by solving the joint transmission beamforming and PS design problem.In the second stage,the optimal beamformer is approximated with the product of analog beamformer and digital beamformer.The superiority of proposed algorithm over the existing algorithms is demonstrated through simulations.Moreover,the effectiveness of approximation algorithm is testified.     

SINR estimation for power control in systems with transmission beamforming

This paper takes a unified approach to the downlink transmission power control, while a transmission beamforming is applied in the base station. The proposed scheme is based on the estimation of signal-to-interference-and-noise-ratios (SINRs) by antenna array measurement and using this estimate in transmission power control. Hence power control algorithms needing SINR-levels can be applied instead of the simple relay power control. The SINR estimation technique does not require any additional measurements compared to a separate adaptive beamforming and power control, since the required measurements are needed for the adaptive beamforming update. The estimation is based on the knowledge of the level of caused interference to the multiple access links in the same cell, and the utilization of relay power control commands in SINR estimation.     

Power allocation for OFDM using adaptive beamforming over wireless networks

The performance of a multiuser wireless network using orthogonal frequency-division modulation (OFDM), combined with power control and adaptive beamforming for uplink transmission is presented here. A network-wide adaptive power control algorithm is used to achieve the desired signal-to-interference-and-noise-ratio at each OFDM subcarrier and increase the power efficiency of the network. As a result, we can achieve a better overall error probability for a fixed total transmit power. With the assumption of fixed-modulation for all subcarriers, transmit powers and beamforming weight vectors at each subcarrier are updated jointly, using an iterative algorithm that converges to the optimal solution for the entire network. Unlike most of the loading algorithms, this approach considers fixed bit allocation and optimizes the power allocation and reduces the interference for the entire network, rather than a single transmitter. We also propose joint time-domain beamforming and power control to reduce the complexity resulting from the number of beamformers and fast Fourier transformed blocks. The proposed algorithm is also extended to COFDM and we show that it improves the performance of those systems.     

Novel Transmit Beamforming Schemes for Time-Selective Fading Multiantenna Systems

Transmit beamforming has been widely adopted for wireless systems with multiple transmit antennas. For a block fading channel, the Grassmannian beamformer has been shown to provide very good performance for finite rate feedback. However, the original Grassmannian beamformer does not take the time domain correlation of the channel fading into consideration. In this paper, based on a first-order autoregressive (AR1) dynamic fading model, we develop two new classes of beamforming algorithms that exploit the interframe correlations in the channel fading. We first introduce an algorithm based on a standard predictive vector quantization (PVQ) approach, and the resulting PVQ beamformer accomplishes superior power delivery at the receiver. However, the error performance of the PVQ beamformer is not satisfactory at high signal-to-noise ratios, and it also has a high implementation complexity. To resolve these issues, we then develop a novel successive beamforming (SBF) algorithm. The new SBF scheme uses the knowledge of the previous fading blocks to aid the beamforming codebook design of the current fading block. The beamforming codebook is constructed based on the successive partition of the surface of a spherical cap. The new SBF scheme accomplishes nearly the same performance as that of the PVQ beamformer, and it has a much simpler implementation. Through numerical simulations, we demonstrate that the proposed beamformers outperform the other previously proposed beamformers at various fading scenarios     

基于稀疏约束和SRV约束的宽带自适应波束形成

针对传统的宽带MVDR自适应波束形成中,抑制干扰的同时会抬高旁瓣电平,且过多的线性约束会导致波束输出的SINR性能下降的问题,提出了一种基于SRV约束和稀疏约束的低旁瓣、高增益宽带自适应波束形成方法.该方法在窄带MVDR自适应波束形成基础上,通过增加波束图稀疏约束来降低波束的旁瓣电平,同时利用空间响应偏差(SRV)约束将窄带算法推广到宽带MVDR 自适应波束形成中,极大地降低了算法的复杂度,改善了波束输出的SINR 性能.与传统方法相比,该方法在降低宽带波束的旁瓣电平的同时,还具有良好的干扰抑制效果.数值仿真实验验证了该方法的有效性.     

TD-SCDMA集群系统中的干扰抑制策略

TD-SCDMA集群系统中会存在各种干扰,一些通过抑制干扰提高系统容量的技术被考虑采纳,如智能天线、多用户检测和功率控制等。传统的功控算法无法消除来自集群群组间的用户干扰。先用波束赋形进行主波瓣外干扰抑制,然后进行多群组联合检测消除波瓣内群组间干扰,从而降低系统对功率控制的要求,提高性能。仿真证明,上述算法能有效降低系统发射功率和抑制干扰。     

Adaptive linearly constrained minimum variance beamforming for multiuser cooperative relaying using the kalman filter

In this paper, we consider a wireless communication scenario with multiple source-destination pairs communicating through several cooperative amplify-and-forward relay terminals. The relays are equipped with multiple antennas that receive the source signals and transmit them to the destination nodes. We develop two iterative relay beamforming algorithms that can be applied in real-time. In both algorithms, the relay beamforming matrices are jointly designed by minimizing the received power at all the destination nodes while preserving the desired signal at each destination. The first algorithm requires the existence of a local processing center that computes the beamforming coefficients of all the relays. In the second algorithm, each relay can compute its beamforming coefficients locally with the help of some common information that is broadcasted from the other relays. This is achieved at the expense of enforcing the desired signal preservation constraints non-cooperatively. We provide two extensions of the proposed algorithms that allow the relays to control their transmission power and to modify the quality of service provided to different sources. Simulation results are presented validating the ability of the proposed algorithms to perform their beamforming tasks efficiently and to track rapid changes in the operating environment.     

Solution of the multiuser downlink beamforming problem with individual SINR constraints

We address the problem of joint downlink beamforming in a power-controlled network, where independent data streams are to be transmitted from a multiantenna base station to several decentralized single-antenna terminals. The total transmit power is limited and channel information (possibly statistical) is available at the transmitter. The design goal: jointly adjust the beamformers and transmission powers according to individual SINR requirements. In this context, there are two closely related optimization problems. P1: maximize the jointly achievable SINR margin under a total power constraint. P2: minimize the total transmission power while satisfying a set of SINR constraints. In this paper, both problems are solved within a unified analytical framework. Problem P1 is solved by minimizing the maximal eigenvalue of an extended crosstalk matrix. The solution provides a necessary and sufficient condition for the feasibility of the SINR requirements. Problem P2 is a variation of problem P1. An important step in our analysis is to show that the global optimum of the downlink beamforming problem is equivalently obtained from solving a dual uplink problem, which has an easier-to-handle analytical structure. Then, we make use of the special structure of the extended crosstalk matrix to develop a rapidly converging iterative algorithm. The optimality and global convergence of the algorithm is proven and stopping criteria are given.     

SINR and throughput improvement for VANET using fuzzy power control

This paper proposes transmission power control for vehicular ad hoc network (VANET) using fuzzy system. Despite the potential advantages of VANET especially for safety and intelligent transportation system, some challenges are discovered during the implementation of VANET. Main challenges emerge because of the dynamic environment and high mobility of vehicle. Furthermore, the interference due to the shared‐spectrum usage can significantly decrease the quality of signal. Fuzzy system is implemented to control the transmission power based on the signal to interference and noise ratio (SINR) difference with the targeted value of the receiver vehicle and the interference inflicted by the transmitter vehicle. The algorithm of fuzzy power control for VANET is proposed, and the performance is evaluated through the simulations. The results of simulations show that the proposed algorithm can increase SINR of vehicles especially the vehicles with SINR value below the target. Thus, the average of SINR and the throughput of the system can be increased as well.     

Feedback‐based multi‐layered STBC system for MIMO multi‐cellular networks with cochannel interference

A feedback‐based multi‐layered STBC (MLSTBC) system, which is adapted to cochannel interference, is proposed. This system can adjust its transmitter configuration so that the largest throughput for the given SINR is obtained, also, it can use joint beamforming and power control to minimize cochannel interference so that the throughput requirement is satisfied. We propose an iterative algorithm to realize joint beamforming and power control for the feedback‐based MLSTBC system, and in this algorithm, we derive the required SINR and the corresponding transmitter configuration for attaining the throughput requirement. Some properties and simulation results are presented, they show that the proposed algorithm helps the feedback‐based MLSTBC system increase the probability of the success in meeting the throughput requirement, also they show that the feedback‐based MLSTBC system results in larger throughput than MLSTBC (with fixed transmitter configuration), STBC, and V‐BLAST. Copyright © 2010 John Wiley & Sons, Ltd.     

Beamforming and power allocation in the downlink of MIMO cognitive radio systems based on multiobjective optimization

In this paper, power allocation and beamforming are considered in a multiple input multiple output (MIMO) downlink cognitive radio (CR) communication system, which a base station (BS) serves one primary user (PU) and one secondary user (SU). In order to design the CR system, a constrained multiobjective optimization problem is presented. Two objectives are the signal to noise plus interference ratios (SINRs) of PU and SU. Since PU has a spectrum license for data communication, a constraint in the optimization problem is that the SINR of PU must be greater than a predefined threshold based on the PU demand requirement. Another constraint is a limitation on power in BS. By considering the mentioned model, three iterative algorithms are proposed. At each iteration of all algorithms, the receiver beamforming vectors are derived based on the maximization of PU and SU SINRs, by assuming that the allocated powers and BS beamforming vectors are known. Also, power is assigned to users such that the constraint of power limitation is satisfied. The difference between the algorithms is in the obtaining of transmitter beamforming parameters. We evaluate the performance of the proposed algorithms in terms of bit error rate (BER) in simulations. Also, the computational complexity of the proposed algorithms is obtained.     

Beamforming for inter‐relay interference reduction in MIMO‐aided two‐path successive relaying

To effectively reduce the inter‐relay interference (IRI) in two‐path successive relaying, two beamforming schemes are proposed in this paper, utilizing multiple‐antenna relay nodes. Specifically, the two cooperation nodes perform receive combining of the source signal and transmit beamforming of the relayed signal alternately in the successive relaying process. As a result, the IRI between them can be effectively suppressed, thanks to the additional degree of freedom provided by the multiple‐input multiple‐output inter‐relay channel. In the first beamforming scheme, the source‐to‐destination signal‐to‐interference‐plus‐noise ratios (SINR) of separate paths are maximized with approximation, leading to a minimum variance distortionless response beamformer under the high SINR condition. To further improve the system performance, noting that the received SINRs of the two paths have impact on each other due to the mutual coupling of the beamformers, the sum of mean squared errors from these two transmission paths is minimized in the second scheme. Based on this performance criterion, a suboptimal beamformer design is developed numerically through cyclic minimization of the sum of mean squared error cost function. Simulation results demonstrate the superiority of both proposed beamforming schemes in terms of symbol error rate and the achievable system rate, in particular, at high IRI levels. Copyright © 2016 John Wiley & Sons, Ltd.     

MIMO雷达稳健的发射波束形成算法

针对发射导向矢量存在未知误差的问题,该文提出了一种MIMO雷达稳健的发射波束形成算法(Robust Transmitting Beamforming, RTB)。该算法在稳健的接收波束形成算法的基础上,以最大化最差情况输出信干噪比为优化准则,对发射导向矢量误差做稳健的发射波束形成。RTB算法属于对角加载方法。仿真结果表明,相比于已有算法,RTB算法的稳健性更好、计算复杂度更低、收敛速度更快。     

Software radio architecture with smart antennas: a tutorial onalgorithms and complexity

There has been considerable interest in using antenna arrays in wireless communication networks to increase the capacity and decrease the cochannel interference. Adaptive beamforming with smart antennas at the receiver increases the carrier-to-interference ratio (CIR) in a wireless link. This paper considers a wireless network with beamforming capabilities at the receiver which allows two or more transmitters to share the same channel to communicate with the base station. The concrete computational complexity and algorithm structure of a base station are considered in terms of a software radio system model, initially with an omnidirectional antenna. The software radio computational model is then expanded to characterize a network with smart antennas. The application of the software radio smart antenna is demonstrated through two examples. First, traffic improvement in a network with a smart antenna is considered, and the implementation of a hand-off algorithm in the software radio is presented. The blocking probabilities of the calls and total carried traffic in the system under different traffic policies are derived. The analytical and numerical results show that adaptive beamforming at the receiver reduces the probability of blocking and forced termination of the calls and increases the total carried traffic in the system. Then, a joint beamforming and power control algorithm is implemented in a software radio smart antenna in a CDMA network. This shows that, by using smart antennas, each user can transmit with much lower power, and therefore the system capacity increases significantly     

Transmit beam-tracking algorithm in FDD CDMA cellular wireless system

A beam-tracking algorithm for downlink transmit beamforming in an FDD CDMA cellular wireless system is investigated. The method takes advantage of the power-controlled system and searches for the beamformer direction corresponding to the minimum transmit power. There is no complex computation needed; thus it simplifies the downlink transmit beamforming system.     

Reverse Link Performance of DS-CDMA Cellular Systems through Closed-Loop Power Control, Base Station Assignment, and Antenna Arrays in 2D Urban Environment

The interference reduction capability of antenna arrays, base station assignment, and the power control algorithms have been considered separately as means to increase the capacity in wireless communication networks. In this paper, we propose smart step closed-loop power control (SSPC) algorithm and base station assignment method based on minimizing the transmitter power (BSA-MTP) technique for direct sequence-code division multiple access (DS-CDMA) receiver in a 2D urban environment. This receiver consists of conjugate gradient adaptive beamforming and matched filter in two stages using antenna arrays. In addition, we study an analytical approach for the evaluation of the impact of power control error (PCE) on the DS-CDMA cellular systems. The simulation results indicate that the SSPC algorithm and the BSA-MTP technique can significantly improve the network bit error rate in comparison with conventional methods. Our proposed methods can also significantly save total transmit power and extend battery life in mobile units. In addition, we show that the convergence speed of the SSPC algorithm is faster than that of conventional algorithms. Finally, we discuss two parameters of PCE and channel propagation conditions (path-loss parameter and variance of shadowing) and their effects on the capacity of the system via some computer simulations.     

Joint Transmit Beamforming and Power Control for CDMA System

1　Introduction　Power control and beamforming are two main methods toreduce interference in CDMA cellular communication sys tem. In power control, the transmitters powers are constant ly adjusted when the instantaneous SIR is not equal to targetSIR, so that the quality of weak links is improved. Base sta tion equipped with antenna arrays may adjust their beam pat terns so that they have maximum gain towards the directionsof target mobiles and minimum gain towards the other direc tio…     

Robust Adaptive Beamformers Based on Worst-Case Optimization and Constraints on Magnitude Response

In this paper, novel robust adaptive beamformers are proposed with constraints on array magnitude response. With the transformation from the array output power and the magnitude response to linear functions of the autocorrelation sequence of the array weight, the optimization of an adaptive beamformer, which is often described as a quadratic optimization problem in conventional beamforming methods, is then reformulated as a linear programming (LP) problem. Unlike conventional robust beamformers, the proposed method is able to flexibly control the robust response region with specified beamwidth and response ripple. In practice, an array has many imperfections besides steering direction error. In order to make the adaptive beamformer robust against all kinds of imperfections, worst-case optimization is exploited to reconstruct the robust beamformer. By minimizing array output power with the existence of the worst-case array imperfections, the robust beamforming can be expressed as a second-order cone programming (SOCP) problem. The resultant beamformer possesses superior robustness against arbitrary array imperfections. With the proposed methods, a large robust response region and a high signal-to-interference-plus-noise ratio (SINR) enhancement can be achieved readily. Simple implementation, flexible performance control, as well as significant SINR enhancement, support the practicability of the proposed methods.