共查询到15条相似文献,搜索用时 359 毫秒
1.
2.
3.
4.
通过热力学计算与模拟试验研究了含钒钛取向硅钢中氮化物析出相的析出规律与析出行为,并探讨了含钒钛元素的氮化物析出相作为薄板坯连铸连轧流程制备取向硅钢中辅助抑制剂的可行性.研究表明,在所冶炼的含钒钛取向硅钢的成分范围内,TiN在钢液凝固末期便具备析出的热力学条件,而AlN与VN只可能在凝固后的α+γ或α+Fe3C两相区内析出.含钒钛取向硅钢中氮化物析出相以成分复杂的复合析出相为主,且随着钒钛加入量的增加,钢中抑制剂析出相总的分布密度由于含钒钛元素的氮化物析出相的增加而明显提高,使抑制剂抑制初次再结晶晶粒正常长大的能力得以加强,最终成品的磁感应强度值B8由1.857 T提升至1.898 T.同时,加入不高于0.007%的Ti与不高于0.005%的V不会影响中间脱碳退火工序的脱碳效果以及高温退火净化阶段硫、氮的脱除效果,其形成的含钒钛元素的纳米级氮化物析出相适合作为薄板坯连铸连轧流程制备取向硅钢的辅助抑制剂. 相似文献
5.
6.
7.
8.
9.
通过研究以Cu2S为主抑制剂的取向硅钢在薄板坯连铸连轧全流程中的组织演变,比较了工艺优化前后的差别。结果表明,TSCR流程试制的取向硅钢经传统的后工序工艺处理,初次再结晶平均晶粒尺寸约为15.5μm,晶粒度为8.61,生产出来的成品中的二次晶粒的尺寸与普通取向硅钢的相当,成品的性能为B8=1.865 T,P1.7/50=1.409 W/kg;后工序的工艺优化后,初次再结晶晶粒更加细小和均匀,平均晶粒尺寸约为13.6μm,晶粒度为9.13,二次再结晶发展更加完善,成品的磁性能得到提升,为B8=1.884 T,P1.7/50=1.394 W/kg;证明以Cu2S为主抑制剂采用TSCR流程生产取向硅钢是可行的。 相似文献
10.
介绍了薄板坯连铸连轧工艺生产无取向硅钢和取向硅钢的工艺特征.通过试样分析和对比工艺条件,研究了这一新工艺与传统工艺生产硅钢的不同点.指出了薄板坯连铸连轧工艺生产硅钢具有的优越性. 相似文献
11.
取向硅钢生产工艺技术分析和发展趋势 总被引:3,自引:0,他引:3
介绍了普通取向硅钢(CGO)和高磁感取向硅钢(Hi-B)铸坯高温加热两次冷轧、一次冷轧和铸坯低温加热两次冷轧、一次冷轧法4种成熟生产工艺的主要技术参数,取向硅钢理论研究(Goss晶核和抑制剂)和生产技术现状。取向钢的发展趋势为:提高(110)[001]晶粒取向度,降低取向硅钢铁损,发展铸坯低温加热(≤1300℃)和薄板坯连铸连轧流程生产取向硅钢工艺。 相似文献
12.
13.
取向硅钢中含铜抑制剂的固溶析出行为 总被引:1,自引:0,他引:1
含铜抑制剂作为取向硅钢的主抑制剂或辅助抑制剂不仅可以抑制初次晶粒的长大,促进二次再结晶,还可以降低铸坯的加热温度。取向硅钢中主要抑制剂为10~50 nm Cu2S,在钢的铸坯、热轧、冷轧、脱碳等工艺过程均可析出;(Cu,Mn)1.8S、Cu1.8S、ε-Cu等主要作为辅助抑制剂,尺寸一般为30~50 nm(或大于50 nm),主要在热轧阶段析出。总结了国内外有关取向硅钢中含铜抑制剂析出行为的研究进展,当前主要研究不同生产流程和工序中含铜抑制剂的析出行为和作用机理。 相似文献
14.
Si-qian Bao Yang Xu Gang Zhao Xiang-bin Huang Huan Xiao Chuan-long Ye Na-na Song Qing-ming Chang 《钢铁研究学报(英文版)》2017,24(1):91-96
A grain-oriented silicon steel strip with AlN as main inhibitor was produced by thin slab casting and rolling (TSCR) process.The microstructure, texture and precipitates of the hot-rolled strip were investigated by use of optical microscope (OM), X-ray diffractometer, transmission electron micro-scope (TEM) and energy dispersive spectroscope (EDS).The result shows that the microstructure and texture exhibit a through-thickness gradient similar to that of the hot-rolled strip produced by con-ventional high-temperature slab-reheating process;the preferred orientation varies from{110}<001>in the surface layer to{001}<110> in the center layer, and the Goss texture with a maximum inten-sity mainly concentrates on the surface layer.In addition, some other texture components, for ex-ample rotated Goss texture, form in the 1/4 thickness layer, which are not observed in the hot-rolled strip produced by conventional high-temperature slab-reheating process.The precipitates in the hot-rolled strip are mainly (Mn,Cu)S and AlN compound particles with dimension of 100-200 nm, and the fine precipitates are significantly less than that in the hot-rolled strip produced by conven-tional high-temperature slab-reheating process.Moreover, the areal density of the fine precipitates in the center layer is more than that in the surface layer. 相似文献
15.
介绍了薄板坯连铸连轧工艺生产无取向硅钢和取向硅钢的工艺特征。重点比较了这一新工艺与传统工艺的不同点。指出了薄板坯连铸连轧工艺生产硅钢具有天然的优越性。 相似文献