功能材料二氧化钛光催化反应活性的研究

TiO2是一种高效节能的光催化功能材料,本文分析了TiO2光催化技术研究现状,探讨了光催化反应机制,并详细讨论了影响TiO2光催化反应活性的主要因素:(1)一般而言,锐钛矿型TiO2的光催化活性高于金红石型TiO2;(2)晶粒尺寸小,光生电子和空穴从TiO2体内扩散到表面的时间短,它们在TiO2体内的复合几率减小,光催化活性高;(3)金属离子掺入TiO2晶格中可能引起晶格位置缺陷或改变结晶度,抑制电子与空穴的复合,延长载流子的寿命,从而使光催化性能得以改善;(4)贵金属沉积可提高催化剂表面光生载流子的分离效率,有利于生成更多的·OH;(5)半导体耦合可提高系统的电荷分离效果,扩展对光谱吸收范围.     

Pb2+改性TiO2薄膜性能的研究

以玻璃为载体,采用溶凝胶胶法制备Pb2 -TiO2薄膜.采用AFM、XRD等技术,考察Pb2 掺杂后对TiO 2晶型结构和光催化活性的影响,结果表明,在相同制备条件下掺杂后使TiO2晶型由锐钛型向金红石型转变温度降低,经AFM分析,掺杂后使TiO2粒径增大,苯酚水溶液的光催化氧化分解反应结果表明,掺杂后TiO2的光催化活性有所提高.     

TiO2/SnO2复合薄膜的低温制备及其光催化性能

采用溶胶-凝胶法合成了TiO2溶胶和SnO2溶胶，使用浸渍提拉法在低温下制备出底层为金红石型SnO2，表层为锐钛矿型TiO2的复合膜．考察了不同SnO2薄膜层数对TiO2／SnO2复合膜光催化活性的影响，并对其光催化活性提高的机理进行了探讨．结果表明，SnO2层的加入能有效提高TiO2薄膜的光催化活性，随着SnO2薄膜层数的增加，光催化活性先增大后减小，但始终高于单一的TiO2薄膜．这是由于SnO2的导带电位低于TiO2的导带电位，SnO2的价带电位高于TiO2的价带电位，紫外光照下，TiO2中产生的光生电子注入到SnO2层，SnO2中空穴注入到TiO2层，有效抑制了薄膜内电子-空穴对的复合，增加了复合薄膜表面空穴的浓度，因而光催化活性得到了显著的提高．     

氧化钛基光催化材料的离子掺杂和酸化改性

本文基于光催化反应的机理分析,采用了金属离子掺杂和表面酸化相结合的改性方法对TiO2颗粒做了优化处理.对改性后的样品利用XRD、FTIR和PL等测试技术对样品进行了表征并以亚甲基兰为模拟污染物进行了光催化降解实验.结果表明包覆在粉体表面的新相以金红石为主;Fe离子掺杂降低了光生电子和空穴的复合几率;表面酸化增加了TiO2表面以双齿桥方式配位的羟基,此种羟基对TiO2光催化活性有重要影响;铁离子掺杂和表面酸化协同的改性方法可以明显提高TiO2粉体的光催化活性.     

Yb-TiO2光催化剂的制备及性能研究

采用溶胶-凝胶法制备了稀土Yb掺杂纳米TiO2光催化剂(Yb-TiO2),采用XRD、UV-Vis、FT-IR等方法对其进行表征和分析,并以亚甲基蓝(MB)作为目标降解物,考察了热处理温度以及Yb掺杂量对样品性能的影响。实验结果表明,Yb掺杂样品均为金红石相和锐钛矿相的混晶相,Yb的掺入拓展了TiO2对可见光的吸收范围,有效地抑制了光生电子-空穴对的复合,提高了TiO2的光催化活性。当pH值=2.5、n(Yb)∶n(Ti)=0.005、热处理温度为650℃时,制备的样品其光催化活性明显优于Degussa P25。     

钠离子对TiO_2薄膜结构及其光催化活性的影响

采用溶胶-凝胶浸渍提拉法在不同玻璃基板上制备TiO2薄膜,并通过降解浸渍在薄膜表面的甲基蓝来评价其光催化活性。利用X射线衍射(XRD)、X射线光电子能谱(XPS)和紫外-可见(UV-Vis)吸收光谱等研究了晶型、表面元素分析和光吸收性能。并采用平行电极法测定TiO2薄膜的光电流,研究了薄膜表面载流子的复合情况。结果表明,薄膜的催化性能主要与基板热扩散到薄膜中的Na+和晶相相关。Na+抑制锐钛矿相TiO2的形成,并且在一定条件下促进由锐钛矿向金红石相的转变。Na+的扩散对TiO2晶粒尺寸影响不大。重要的是,扩散至薄膜的Na+不仅影响TiO2薄膜的晶相转变,而且成为光生电子与空穴的复合中心,同时影响其光催化活性。     

La/TiO2-SiO2薄膜的光催化性能研究

采用溶胶-凝胶法制备了不同掺杂量的La／TiO2-SiO2复合薄膜．通过XRD、FE-SEM和AFM研究了复合薄膜的微观结构，采用紫外光照射下亚甲基蓝的分解实验比较薄膜的光催化性能．结果表明：La掺杂可显著提高TiO2-SiO2复合薄膜的光催化活性，以5％掺杂量为最佳，其光降解率比掺杂前提高了约23％．薄膜活性提高的主要原因是La掺杂后细化了TiO2的晶粒，提高了薄膜的比表面积，使其具有更高的氧化还原电势，La^3＋取代Ti^4＋进入到TiO2晶格，引起晶格膨胀，这种不同价离子的取代导致TiO2粒子表面电荷分布不平衡，从而提高了光生电子-空穴的分离效率．     

金红石二氧化钛纳米片的性质及其光催化活性

采用溶胶-凝胶、质子交换和层状剥离的方法, 制备出金红石TiO₂纳米片。利用X射线电子衍射谱(XRD)、透射电子显微镜(TEM)、紫外-可见吸收光谱(UV-Vis)、X光电子能谱(XPS)的价带谱和荧光光谱(PL)等对样品进行了表征, 研究了光生载流子的转移过程。结果证明: 金红石TiO₂纳米片具有较大的比表面积(185.7 m²/g), 厚度约5 nm, 与金红石TiO₂样品相比, 金红石TiO₂纳米片的禁带宽度增加, 氧化还原能力增强; 此外, 纳米片结构能够促使光生载流子快速转移到纳米片的表面并产生有效分离, 阻止了光生电子和空穴的复合, 提高了光催化反应中光生载流子的利用率。金红石纳米片的这些特性导致其具有较高的光催化活性, 紫外光催化降解对氯苯酚的实验表明: 金红石TiO₂纳米片的光催化活性高于金红石TiO₂和锐钛矿TiO₂样品。     

Sb对直流反应磁控溅射制备TiO2薄膜的影响

用直流磁控溅射方法在Si(100)面及载玻片上制备了Sb掺杂TiO2薄膜.利用XRD光谱研究了Sb对其薄膜结晶情况的影响,用AFM观察其表面形貌,利用分光光度计测量了TiO2薄膜的光学特性及其对亚甲基蓝的分解活性,通过测量和计算表面对水的接触角来衡量光致亲水性.研究结果表明纯TiO2薄膜为锐钛矿型,适量Sb的掺杂能使TiO2薄膜的结晶有显著改善,并出现Ti2O3和金红石相TiO2,薄膜的光催化活性和光致亲水性明显改善.随着掺杂量的增加,TiO2薄膜的吸收边逐渐红移.但Sb掺杂过量时,破坏了二氧化钛原有的晶格结构,光催化活性和光致亲水性也相应降低.     

浸渍-沉积法制备一维Au/TiO_2的光催化性能研究

以钛酸纳米管为载体、HAuCl4为金前驱体,通过浸渍-沉积法制备一维金修饰TiO2光催化剂(Au/TiO2)。通过X射线衍射和紫外-可见漫反射吸收光谱研究材料的结构和性质。以甲基橙溶液作为模拟废液,研究Au/TiO2材料在紫外光条件下的光催化活性。研究表明,由于金可以接受电子,从而促进光生电子和光生空穴的分离,使TiO2的光催化活性提高;Au/TiO2的光催化活性还与金的含量密切相关,金的最佳负载量为1%(质量分数)。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Effect of Oxide Assisted Metal Nanoparticles on Microstructure and Morphology of Gallium oxide Nanowires

Several researches have been reported about the characteristic of β-Ga2O3 nanowires which was synthesized on nickel oxide particle. But indeed, recent researches about synthesis of β-Ga2O3 nanowires on oxide-assisted transition metal are limited to nickel or cobalt oxide catalyst. In this work, Gallium oxide (β-Ga2O3 ) nanowires were synthesized by a simple thermal evaporation method from gallium powder in the range of 700 - 1000℃ using the iron, nickel, copper, cobalt and zinc oxide as a catalyst, respectively. The β-Ga2O3 nanowires with single crystalline without defects were successfully synthesized at the reaction temperature of 850, 900 and 950℃ in all the catalysts. But optimum experimental condition in synthesis of nanowires varied with the kind of catalyst. As increasing synthesis temperature,the morphology of gallium oxide nanowires changed from nanowires to nanorods, and its diameter increased. From these results, we could be proposed that the growth mechanism of β-Ga2O3 nanowires was changed with synthesis temperature of nanowires. Microstructure and morphology of Synthesized nanowire was characterized by HR-TEM, FE-SEM, EDX and XRD.     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from