烧结过程对Nd-Fe-B永磁材料磁性能与力学性能的影响

分析了烧结过程对Nd-Fe-B永磁材料磁性能和力学性能的影响.当烧结温度为1 373 K时,随烧结保持时间延长,材料剩磁Br先增加后趋于稳定,矫顽力Hci直线下降.成分为Nd25.5Pr7.5FebalNb0.45Cu0.2Al0.55B1.10的磁体样品的抗弯强度在烧结时间为5 h时达到一个最大值后便持续下降,而成分为Nd25.5Pr7.57.5FebalNb0.15Cu0.25Al0.75B1.10的磁体样品抗弯强度是持续下降的.试验结果表明:通过优化合金成分和烧结工艺参数,可以改善烧结Nd-Fe-B永磁材料的磁性能和力学性能,获得综合性能较高的磁体.     

微量添加晶界合金对烧结Nd-Fe-B力学性能及微观结构的影响

采用双合金法制备系列烧结Nd—Fe—B磁体(保持其主合金成分不变：Ndl4．1Dy0．5Fe79.0B6.4(原子分数)，所添加的晶界合金中的B含量从0．95％(原子分数)逐步增加到6．95％(原子分数))，研究了微量添加晶界合金对烧结Nd—Fe—B力学性能及微观结构的影响。研究结果表明：微量添加晶界合金所制备的磁体，其抗弯强度值普遍高于单合金法制得的磁体；前者的抗弯强度最高可达397MPa，高于铸造，热压磁体的抗弯值，而后者的抗弯强度仅为309MPa。由相结构分析可知，当添加的晶界合金中的B含量为O．95(原子分数)，主相晶格的四方度减小，这时磁体具有最高的抗弯强度。另外，微量添加晶界合金，可使磁体中晶界相的分布更加均匀，从而基本上消除了主相晶粒直接接触的现象，使晶粒的不规则长大得到抑制。这也是微量添加晶界合金后磁体具有较高抗弯强度的原因之一。对磁性能的研究结果表明，微量添加晶界合金几乎不影响烧结Nd—Fe—B磁体的磁性能。     

烧结Nd-Fe-B磁体腐蚀动力学行为

研究了不同成分的烧结Nd-Fe-B磁体在恒定湿热和中性盐雾腐蚀环境中的腐蚀动力学行为,讨论了不同合金成分和腐蚀条件对磁体腐蚀速率的影响,探讨了烧结Nd-Fe-B磁体在不同介质中的电化学行为.结果表明:烧结Nd-Fe-B磁体在湿热环境中的重量变化表现出明显的抛物线衰减规律,而在盐雾腐蚀环境中的重量变化表现出先增后减的规律.以重稀土Dy替代少量Nd,并添加少量Co等元素,可以提高烧结Nd-Fe-B磁体的耐湿热和耐盐雾腐蚀性能.     

Nd-Fe-B磁体烧结致密化过程的研究

定量描述了Nd-Fe-B磁体的烧结致密化过程, 分析了有效稀土含量、合金粉末粒度与烧结致密化过程的关系, 讨论了Nd-Fe-B磁体烧结过程的致密化机制. Nd-Fe-B磁体烧结致密化过程可分为3个阶段, 即致密化过程迅速进行阶段、缓慢进行阶段、相对稳定阶段;随着烧结温度的上升, 第一阶段表现得更为突出, 第二阶段对应的烧结时间区段大大缩短. 有效稀土含量的提高、合金粉末粒度的减小显著促进Nd-Fe-B磁体烧结致密化过程. 主相颗粒重排以及主相颗粒长大与形状适位性变化是Nd-Fe-B磁体烧结过程的两类主要致密化机制, 而且后者对于Nd-Fe-B烧结磁体实现完全致密化起着决定性的作用.     

烧结钕铁硼的磁性能和力学性能研究进展

重点介绍深冷处理对烧结钕铁硼磁性能的研究、目前力学性能研究现状以及研究烧结钕铁硼力学性能的重要性。     

含Ce烧结Nd-Fe-B磁体的腐蚀行为

采用双主相合金技术制备了含Ce烧结钕铁硼磁体.Ce元素替代传统Nd/Dy元素总量的15%时,含Ce磁体具有良好的失重率,明显优于商业用N33和N45磁体.通过测量磁体在Na OH溶液中的极化曲线表明,含Ce磁体的腐蚀电位和腐蚀电流密度均好于商业用N33和N45磁体.SEM分析显示,含Ce磁体的晶粒尺寸明显小于其他商业用磁体,并且富钕相更加细小,分布均匀.含Ce磁体具有良好耐蚀性的主要原因是:Ce的加入,细化的晶粒,减小了富钕相尺寸,进而提高了磁体的腐蚀电位.     

烧结Nd-Fe-B磁体的温度稳定性缺陷分析

采用SEM、EDAX及粒度分析手段,研究了烧结Nd-Fe-B磁体开路磁通不可逆损失(hirr)异常偏高的原因。结果表明,磁体显微组织中晶粒尺寸分布不均匀及存在少量粗大晶粒,是导致其温度稳定性缺陷的主要因素,表现为少数产品hirr异常偏高。在磁体工业生产过程中,改进原料的铸锭和制粉技术,避免出现粗大粉末颗粒,减少极细粉末颗粒的数量,保证磁体显微组织精细均匀,是制备温度稳定性高的烧结Nd-Fe-B磁体的基本措施。     

Nd-Fe-B磁体热等静压烧结的实验研究

研究了热等静压烧结对Nd-Fe-B磁体的致密度、显微组织及磁性能的影响.结果表明:与常压烧结磁体相比,热等静压烧结磁体的内部存在较多的孔洞,致密度、晶粒取向度及磁性都有所降低.用加热Ar气热膨胀而产生热等静压进行烧结的办法不适于制造高性能的烧结磁体.     

不同工艺所制备烧结Nd-Fe-B合金的耐腐蚀性研究

研究了氢破碎(HD)工艺和常规(CG)工艺制备的烧结Nd-Fe-B合金样品在HCl溶液、Na(OH)溶液及饱和食盐水中的耐腐蚀性,并对两种工艺所制备样品的微观形貌进行了分析。结果表明,在HCl溶液、Na(OH)溶液及饱和食盐水中,样品在前8h内的腐蚀速率均较快,随后腐蚀速率均变慢;HCl溶液对烧结Nd-Fe-B合金的腐蚀性比Na(OH)溶液、饱和食盐水强得多。氢破碎工艺制备的合金耐腐蚀性优于常规工艺制备的合金,且未充磁合金的耐腐蚀性优于充磁合金。     

高Dy含量烧结Nd-Fe-B的晶界扩散处理研究

研究了晶界扩散处理对高Dy含量烧结Nd-Fe-B磁体性能和结构的影响。经蒸镀渗Dy晶界扩散处理,高Dy含量Nd-Fe-B磁体的矫顽力从1 713 kA/m提高至2 161 kA/m,而剩磁和最大磁能积基本没有下降,处理后磁体内Dy平均质量分数仅增加0.30%。不同深度片层分析表明,虽然磁体近表面片层比中心片层的Dy含量高,但是片层间矫顽力相差较少,而且所有片层的矫顽力均远高于未处理磁体片层的矫顽力。电子探针Dy元素面分布结果显示,在未处理高Dy含量磁体的晶界与主相中均存在Dy元素富集区且富集浓度较低,而经扩散处理后,晶界富Nd相中的Dy富集区浓度及所占比例明显提高;包括磁体芯部在内,磁体内大部分角隅处富Nd相内Dy含量明显增加,进一步提高了高Dy含量磁体内部各处的矫顽力。     

添加Dy2O3的烧结钕铁硼磁体的磁性能与力学性能

应用常规粉末冶金工艺制备添加不同质量分数Dy2O3的32(Pr-Nd) -0.60Gd -0.55Nb -0.20Cu -0.45Al - 1.12B - Fe烧结磁体,分析了磁性能、抗弯强度、显微组织的变化规律.结果表明,添加Dy2O3使磁体内禀矫顽力近似线性地上升,而剩磁与磁能积则近似线性地下降;添加1.0％的Dy...     

镝扩渗对烧结钕铁硼磁体组织结构与磁性能的影响

对比研究了38UH、42SH和N50薄片状钕铁硼磁体晶界镝扩渗前后的组织结构与磁性能,发现经过镝扩渗处理后磁体的矫顽力提高了400 kA·m^-1以上,而剩磁几乎不变,最大磁能积因为矫顽力和方形度的提高而提高。经组织结构分析认为,钕铁硼磁体晶界镝扩渗提高矫顽力主要是通过提高Nd₂Fe₁₄B晶粒外延层的各向异性和形核场实现的。根据Fick第一扩散定律,对磁体晶界镝扩渗进行了模拟计算,可近似得到定温热处理不同时间后渗镝深度及对应的镝的质量浓度及质量分数。     

Enhanced mechanical properties in die-upset Nd-Fe-B magnets via die-upsetting process

The mechanical properties of die-upset Nd-Fe-B magnets produced at different die-upset processes were investigated. The results showed that the optimum comprehensive mechanical properties of die-upset Nd-Fe-B magnets were obtained at the deformation temperature of 680 oC. The anisotropy of Vickers hardness was more obvious at the die-upset level of 55%, and the Vickers hardness measured parallel to the c-axis was significantly lower than that perpendicular to the c-axis. The fracture toughness measured parallel to the c-axis first increased, and then decreased with increase in die-upset level. The maximum fracture toughness of Nd-Fe-B magnets was obtained at the die-upset level of 60%. The microstructure showed that the width of defect layers and the average size of large grains increased, and the layered structure of die-upset Nd-Fe-B magnets was obviously different with increase in the die-upset level.     

放电等离子体烧结NdFeB永磁材料力学性能的研究

采用传统烧结技术和放电等离子体烧绱技术（SPS）制备相同成分的烧结NdFeB水磁合金。研究了所制备合金的力学性能和断裂行为。利用扫描电子显微镜观察了合金的显微组织和断口形貌；测量了合金的抗弯强度并对磁体的力学性能进行评价。结果表明：SPS NdFeB磁体的抗弯渔度较传统烧结体有显著的提高，前者a bb=402．25MPa，后者abb=278．97Mpa；SPS NdFeB磁体显微绀织主相晶粒细小均匀、富稀土相细小弥散且彼此隔断，断口观察发现了较明显的撕裂棱及一些解理断裂；而传统烧结磁体主相晶粒粗大、富稀土相粗大且彼此连接。沿晶断裂特征明显。     

Effect of yttrium substitution on magnetic properties and service performances of Nd-Fe-B sintered magnets

We successfully fabricated partial Y substituted NdY-Fe-B magnets with nominal compositions of(Nd_1-xY_x)_13.80Fe_ba1Al_0.24Cu_0.1B_6.04(at%,x=0,0.1,0.2,0.3,0.4) by powder metallurgy process and the magnetic properties as well as service performances of the magnets were also systematically investigated.The phase constituents of the magnets have no obvious variation within the whole range of Y content,while the main phase grain...     

Effects of Pr-Cu-Ti intergranular addition on microstructure and magnetic properties of heavy-rare-earth-free Nd-Fe-B sintered magnets

By intergranular addition of Pr-Cu-Ti alloy powders in the Nd-Fe-B sintered magnets with the normal B component, we propose an approach to the optimization of grain boundary and local Nd-Fe-B composition system. The coercivity is enhanced from 1.42 to 1.86 T, while further addition leads to a reduction in remanence and coercivity. The analyses of phase composition reveal that Ti mainly exists in the form of metallic Ti alloy, and part of Ti combines with B to form the TiB₂ phase after the liquid phase sintering process. This process results in a consumption of B in the local Nd-Fe-B composition system and a change of the grain boundary component, which contributes to the formation process of the RE₆(Fe,M)₁₄ phase after the annealing process. Therefore, with the modification of grain boundary and composition system, the intergranular addition of Pr-Cu-Ti induces the generation of continuous thin grain boundary phases. It promotes the intergrain exchange decoupling, increasing the coercivity in the annealed magnet. While the excess addition results in the segregation of TiB₂, as well as the precipitation of TiB₂ into the Nd-Fe-B phase, which leads to structural defects. Thus, the further effort for the addition alloy with Ti to reduce the deterioration of the microstructure will lead to further improvement in magnetic properties.     

Microstructural investigation of Nd-rich phase in sintered Nd-Fe-B magnets through electron microscopy

The distribution, morphologies and structures of intergranular Nd-rich phase in sintered Nd-Fe-B magnets were studied through electron microscopy. Backscattered electron (BSE) imaging revealed that Nd-rich particles with various morphologies and sizes were randomly distributed at the grain boundaries and the triple junctions of the tetragonal Nd2Fe14B matrix. Through selected area electron diffraction (SAED) analysis under a systematic tilting condition, most intergranular Nd-rich phase particles, with sizes ranging from hundreds of nanometres to several micrometres, were identified as face-centred cubic (FCC) structure. Such particles possessed several approximate orientation relationships with their adjacent Nd2Fe14B matrix grains, such as (002) Nd2Fe14B//(200) FCC_Nd-rich [120] Nd2Fe14B//[001] FCC_Nd-rich , (002) Nd2Fe14B//( 220 ) FCC_Nd-rich [110] Nd2Fe14B//[112] FCC_Nd-rich , as well as (011) Nd2Fe14B//(131) FCC_Nd-rich [111] Nd2Fe14B//[114] FCC_Nd-rich , which could be attributed to minimising interfacial energy. The combination of highresolution electron microscopy with energy-dispersive X-ray spectroscopy revealed the internal inhomogeneous nature of Nd-rich phases. The large lattice distortion and nanoscale-ordered structures within a single Nd-rich grain were observed.     

晶间合金化Ga元素对烧结Nd-Fe-B磁性能与显微组织的影响

用晶间合金化方式直接在(NdPr)29.6(FeCuZr)69.2B1.0粉中加入0.3%Ga(质量分数,以下同),磁体的内禀矫顽力从943.5kA/m提高到1181.0kA/m。分别用晶间合金化方式和传统合金化方式在(Nd-PrDy)30.0(FeCuZr)69.0B1.0中加入0.2%Ga,前者的内禀矫顽力达到1224.0kA/m,远高于后者的971.5kA/m。显微组织结构分析表明:用晶间合金化方式加Ga后改善了边界结构,没加Ga时晶粒边界不平直,晶界处缺陷较多;加Ga后晶界平直光滑,Ga主要分布在晶界,而晶内Ga含量极低。     

Ni对热变形Nd-Fe-B磁体磁性能及力学性能的影响

为提高热压结合热变形工艺制备的各向异性Nd-Fe-B磁体的力学性能,向磁体中掺杂高熔点、弱磁性金属元素Ni,研究Ni含量对磁体的磁性能、力学性能以及微观结构的影响。掺杂Ni的质量分数在0~5%之间时,Nd-Fe-B复合磁体的抗弯强度先增大后减小,2%Ni含量的Nd-Fe-B复合磁体具有最高平均抗弯强度212 MPa,其最大磁能积保持在40 MGOe以上。从磁体断口形貌上看,Ni会在孔洞附近富集,强化增韧晶界相,从而提高晶界相的裂纹扩展阻力,使抗弯强度提高。