High-mobility ultrathin strained Ge MOSFETs on bulk and SOI with low band-to-band tunneling leakage: experiments

For the first time, the tradeoffs between higher mobility (smaller bandgap) channel and lower band-to-band tunneling (BTBT) leakage have been investigated. In particular, through detailed experiments and simulations, the transport and leakage in ultrathin (UT) strained germanium (Ge) MOSFETs on bulk and silicon-on-insulator (SOI) have been examined. In the case of strained Ge MOSFETs on bulk Si, the resulting optimal structure obtained was a UT low-defect 2-nm fully strained Ge epi channel on relaxed Si, with a 4-nm Si cap layer. The fabricated device shows very high mobility enhancements >3.5/spl times/ over bulk Si devices, 2/spl times/ mobility enhancement and >10/spl times/ BTBT reduction over 4-nm strained Ge, and surface channel 50% strained SiGe devices. Strained SiGe MOSFETs having UT (T/sub Ge/<3 nm) very high Ge fraction (/spl sim/ 80%) channel and Si cap (T/sub Si cap/<3 nm) have also been successfully fabricated on thin relaxed SOI substrates (T/sub SOI/=9 nm). The tradeoffs in obtaining a high-mobility (smaller bandgap) channel with low tunneling leakage on UT-SOI have been investigated in detail. The fabricated device shows very high mobility enhancements of >4/spl times/ over bulk Si devices, >2.5/spl times/ over strained silicon directly on insulator (SSDOI; strained to 20% relaxed SiGe) devices, and >1.5/spl times/ over 60% strained SiGe (on relaxed bulk Si) devices.     

Hole transport in UTB MOSFETs in strained-Si directly on insulator with strained-Si thickness less than 5 nm

Hole transport is studied in ultrathin body (UTB) MOSFETs in strained-Si directly on insulator (SSDOI) with a Si thickness down to 1.4 nm. In these Ge-free SSDOI substrates, the Si is strained in biaxial tension with strain levels equivalent to strained-Si on relaxed SiGe, with Ge contents of 30 and 40% Ge. The hole mobility in SSDOI decreases slowly for Si thicknesses above 4 nm, but drops rapidly below that thickness. Relative to silicon-on-insulator control devices of equal thickness, SSDOI displays significant hole mobility enhancement for Si film thicknesses above 3.5 nm. Peak hole mobility is improved by 25% for 40% SSDOI relative to 30% SSDOI fabricated by the same method, demonstrating the benefits of strain engineering for 3.1-nm-thick UTB MOSFETs.     

应变Si1-xGex沟道PMOSFET空穴局域化研究

为充分利用应变 Si Ge材料相对于 Si较高的空穴迁移率 ,研究了 Si/Si Ge/Si PMOSFET中垂直结构和参数同沟道开启及空穴分布之间的依赖关系。在理论分析的基础上 ,以数值模拟为手段 ,研究了栅氧化层厚度、Si帽层厚度、Si Ge层 Ge组分及厚度、缓冲层厚度及衬底掺杂浓度对阈值电压、交越电压和空穴分布的影响与作用 ,特别强调了 δ掺杂的意义。模拟和分析表明 ,栅氧化层厚度、Si帽层厚度、Si Ge层 Ge组分、衬底掺杂浓度及 δ掺杂剂量是决定空穴分布的主要因素 ,而 Si Ge层厚度、缓冲层厚度和隔离层厚度对空穴分布并不敏感。最后总结了沟道反型及空穴分布随垂直结构及参数变化的一般规律 ,为优化器件设计提供了参考。     

Ultrathin-body strained-Si and SiGe heterostructure-on-insulator MOSFETs

The combination of channel mobility-enhancement techniques such as strain engineering with nonclassical MOS device architectures, such as ultrathin-body (UTB) or double-gate structures, offers the promise of maximizing current drive while maintaining the electrostatic control required for aggressive device scaling in future technology nodes. The tradeoff between transport enhancement and OFF-state leakage current is compared experimentally for UTB MOSFETs in two types of materials: 1) strained Si directly on insulator (SSDOI) and 2) strained Si/strained Si/sub 1-z/Ge/sub z/ (z=0.46-0.55)/strained Si heterostructure-on-insulator (HOI). SSDOI of moderate strain level (e.g. /spl sim/ 0.8%) yields high electron-mobility enhancements for all electron densities, while high strain levels (e.g. /spl sim/ 1.6%) are required to obtain hole-mobility enhancements at high inversion charge densities. HOI is demonstrated to have similar electron-mobility characteristics to SSDOI, while hole mobilities are improved and can be maintained at high inversion charge densities. Hole mobility in strained channels with thickness below 10 nm is studied and compared for SSDOI and HOI. As the channel thickness is reduced, mobility decreases, as in unstrained silicon-on-insulator (SOI), though hole-mobility enhancements are demonstrated into the ultrathin-channel regime. Increased OFF-state leakage currents are observed in HOI compared to SSDOI and SOI. For a 4-nm-thick buried SiGe layer, leakage is reduced relative to devices with thicker SiGe channels.     

High Mobility Strained Ge pMOSFETs With High-κ/Metal Gate

Compressively strained Ge long channel ring-type pMOSFETs with high-kappa Si/SiO₂/HfO₂/TiN gate stacks are fabricated on Si_0.2Ge_0.8 virtual substrates. Effective oxide thickness is approximately 1.4 nm with low gate leakage current. A peak hole mobility of 640 cm²/ Vldrs and up to a four times enhancement over the Si/SiO₂ universal curve are observed. Parasitic conduction within the Si-cap layers degrades the mobility at large vertical fields, although up to a 2.5 times enhancement over universal remains at a field of 0.9 MV/cm.     

Tensile-Strained Germanium CMOS Integration on Silicon

Monolithic integration of tensile-strained Si/ Germanium (Ge)-channel n-MOS and tensile-strained Ge p-MOS with ultrathin (equivalent oxide thickness ~14 Aring) HfO₂ gate dielectric and TaN gate stack on Si substrate is demonstrated. Defect-free Ge layer (279 nm) grown by ultrahigh vacuum chemical-vapor deposition is achieved using a two-step Ge-growth technique coupled with compliant Si/SiGe buffer layers. The epi-Ge layer experiences tensile strain of up to ~0.67% and exhibits a peak hole mobility of 250 cm²/V ldr s which is 100% higher than the universal Si hole mobility. The gate leakage current is two orders of magnitude lower compared to the reported results on Ge bulk.     

A deep submicron Si1-xGex/Si vertical PMOSFETfabricated by Ge ion implantation

We report a deep submicron vertical PMOS transistor using strained Si_1-xGe_x channel formed by Ge ion implantation and solid phase epitaxy. These vertical structure Si_1-xGe_x /Si transistors can be fabricated with channel lengths below 0.2 μm without using any sophisticated lithographic techniques and with a regular MOS process. The enhancement of hole mobility in a direction normal to the growth plane of strained Si_1-xGe_x over that of bulk Si has been experimentally demonstrated for the first time using this vertical MOSFET. The drain current of these vertical MOS devices has been found to be enhanced by as much as 100% over control Si devices. The presence of the built-in electric field due to a graded SiGe channel has also been found to be effective in further enhancement of the drive current in implanted-channel MOSFET's     

Fabrication of thick, high-quality strained SiGe layer on ultra-thin silicon-on-insulator and modeling of film strain

Fabrication of a thick strained SiGe layer on bulk silicon is hampered by the lattice mismatch and difference in the thermal expansion coefficients between Si and SiGe, and a high Ge content leads to severe strain in the SiGe film. When the thickness of the SiGe film is above a critical value (90 nm for 18% Ge), drastic deterioration of the film properties as well as dislocations will result. In comparison, a silicon-on-insulator (SOI) substrate with a thin top Si layer can mitigate the problems and so a thick SiGe layer with high Ge concentration can conceivably be synthesized. In the work reported here, a 110 nm thick high-quality strained Si_0.82Ge_0.18 layer was fabricated on an ultra-thin SOI substrate with a 30 nm top silicon layer using ultra-high vacuum chemical vapor deposition (UHVCVD). The thickness of the SiGe layer is larger than the critical thickness on bulk Si. Cross-sectional transmission electron microscopy (XTEM) reveals that the SiGe layer is dislocation-free and the atoms at the SiGe/Si interface are well aligned, even though X-ray diffraction (XRD) data indicate that the SiGe film is highly strained. The strain factors determined from the XRD and Raman results agree well.     

Hole and electron mobility enhancement in strained SiGe verticalMOSFETs

We have fabricated strained SiGe vertical P-channel and N-channel metal-oxide-semiconductor field-effect transistors (MOSFETs) by Ge ion implantation and solid phase epitaxy. No Si cap is needed in this process because Ge is implanted after gate oxide growth. The vertical MOSFETs are fabricated with a channel length below 0.2 μm without sophisticated lithography and the whole process is compatible with a regular CMOS process. The enhancement for the hole and electron mobilities in the direction normal to the growth plane of strained SiGe over that of bulk Si has been demonstrated in this vertical MOSFET device structure for the first time. The drain current for the vertical SiGe MOSFETs has been found to be enhanced by as much as 100% over the Si control devices and the drain current for the vertical SiGe NMOSFETs has been enhanced by 50% compared with the Si control de, ices on the same wafer. The electron mobility enhancement in the normal direction is not as significant as that for holes, which is in agreement with theoretical predictions     

Fabrication of strained Si channel PMOSFET on thin relaxed Si1−xGex virtual substrate

A novel MBE-grown method using low-temperature Si technology is introduced into the fabrication of strained Si channel PMOSFETs. The thickness of relaxed Si_1−xGe_x epitaxy layer on bulk silicon is reduced to approximate 400 nm (x=0.2). The Ge fraction and relaxation of Si_1−xGe_x film are confirmed by DCXRD (double crystal X-ray diffraction) and the DC characteristics of strined Si channel PMOSFET measured by HP 4155B indicate that hole mobility μ_p has an maximum enhancement of 25% compared to similarly processed bulk Si PMOSFET.     

Improved Ge Surface Passivation With Ultrathin SiOX Enabling High-Mobility Surface Channel pMOSFETs Featuring a HfSiO/WN Gate Stack

To realize high-mobility surface channel pMOSFETs on Ge, a 1.6-nm-thick SiO_X passivation layer between the bulk Ge substrate and HfSiO gate dielectric was introduced. This approach provides a simple alternative to epitaxial Si deposition followed by selective oxidation and leads to one of the highest peak hole mobilities reported for unstrained surface channel pMOSFETs on Ge: 332 cm² middotV^-1middots^-1 at 0.05 MV/cm-a 2times enhancement over the universal Si/SiO₂ mobility. The devices show well-behaved output and transfer characteristics, an equivalent oxide thickness of 1.85 nm and an I_ON/I_OFF ratio of 3times10³ without detectable fast transient charging. The high hole mobility of these devices is attributed to adequate passivation of the Ge surface     

应变Si1-xGex pMOSFET反型沟道空穴低场迁移率模型

在考虑应变对SiGe合金能带结构参数影响的基础上,提出了一个半经验的应变Sil-xGex/Si pMOSFET反型沟道空穴迁移率模型.在该模型中,给出了迁移率随应变的变化,并且考虑了界面陷阱电荷对载流子的库仑散射作用.利用该模型对室温下空穴迁移率随应变的变化及影响空穴迁移率的因素进行了分析讨论.     

应用400℃低温Si技术制备应变Si沟道pMOSFET

在利用分子束外延方法制备SiGe pMOSFET中引入了低温Si技术.通过在Si缓冲层和SiGe层之间加入低温Si层,提高了SiGe层的弛豫度.当Ge主分为20%时,利用低温Si技术生长的弛豫Si1-xGex层的厚度由UHVCVD制备所需的数微米降至400nm以内,AFM测试表明其表面均方粗糙度(RMS)小于1.02nm.器件测试表明,与相同制备过程的体硅pMOSFET相比,空穴迁移率最大提高了25%.     

Si‐core/SiGe‐shell channel nanowire FET for sub‐10‐nm logic technology in the THz regime

The p‐type nanowire field‐effect transistor (FET) with a SiGe shell channel on a Si core is optimally designed and characterized using in‐depth technology computer‐aided design (TCAD) with quantum models for sub‐10‐nm advanced logic technology. SiGe is adopted as the material for the ultrathin shell channel owing to its two primary merits of high hole mobility and strong Si compatibility. The SiGe shell can effectively confine the hole because of the large valence‐band offset (VBO) between the Si core and the SiGe channel arranged in the radial direction. The proposed device is optimized in terms of the Ge shell channel thickness, Ge fraction in the SiGe channel, and the channel length (L_g) by examining a set of primary DC and AC parameters. The cutoff frequency (f_T) and maximum oscillation frequency (f_max) of the proposed device were determined to be 440.0 and 753.9 GHz when L_g is 5 nm, respectively, with an intrinsic delay time (τ) of 3.14 ps. The proposed SiGe‐shell channel p‐type nanowire FET has demonstrated a strong potential for low‐power and high‐speed applications in 10‐nm‐and‐beyond complementary metal‐oxide‐semiconductor (CMOS) technology.     

基于SiGe虚拟衬底的低场迁移率提升140%的应变Si沟道NMOS器件 Cui Wei(崔伟)1,2,Tang Zhaohuan(唐昭焕)2, Tan Kaizhou(谭开洲)2, Zhang Jing(张静)2,

本文研究了一种应变SiGe沟道的NMOS器件,通过调整硅帽层、SiGe缓冲层,沟道掺杂和Ge组分变化,并采用变能量硼注入形成P阱的方式,成功完成了应变NMOS器件的制作。测试结果表明应变的NMOS器件在低场(Vgs=3.5V, Vds=0.5V)条件下,迁移率极值提升了140%,而PMOS器件性能保持不变。文中对硅基应变增强机理进行了分析。并利用此NMOS器件研制了一款CMOS倒向器,倒向器特性良好, 没有漏电,高低电平转换正常。     

<100>沟道方向对高迁移率双轴应变硅p-MOSFET的作用

双轴应变技术被证实是一种能同时提高电子和空穴迁移率的颇有前景的方法;<100>沟道方向能有效地提升空穴迁移率.研究了在双轴应变和<100>沟道方向的共同作用下的空穴迁移率.双轴应变通过外延生长弛豫SiGe缓冲层来引入,其中,弛豫SiGe缓冲层作为外延底板,对淀积在其上的硅帽层形成拉伸应力.沟道方向的改变通过在版图上45°旋转器件来实现.这种旋转使得沟道方向在(001)表面硅片上从<110>晶向变成了<100>晶向.对比同是<110>沟道的应变硅pMOS和体硅pMOS,迁移率增益达到了130%;此外,在相同的应变硅pMOS中,沟道方向从<110>到(100)的改变使空穴迁移率最大值提升了30%.讨论和分析了这种双轴应变和沟道方向改变的共同作用下迁移率增强的机理.     

Ultrathin body SiGe-on-insulator pMOSFETs with high-mobility SiGe surface channels

A novel concept and a fabrication technique of strained SiGe-on-insulator (SGOI) pMOSFET are proposed and demonstrated. This device has an ultrathin strained SiGe channel layer, which is directly sandwiched by gate oxide and buried oxide layers. The mobility enhancement of 2.3 times higher than the universal mobility of conventional universal Si pMOSFETs was obtained for a pMOSFET with 19-nm-thick Si/sub 0.58/Ge/sub 0.42/ channel layer, which is formed by high-temperature oxidation of a Si/sub 0.9/Ge/sub 0.1/ layer grown on a Si-on-insulator (SOI) substrate. A fully depleted SGOI MOSFET with this simple single-layer body structure is promising for scaled SOI p-MOSFET with high current drive.     

Hole mobility in ultrathin body SOI pMOSFETs with SiGe or SiGeC channels

The hole mobilities of SiGe and SiGeC channel pMOSFETs fabricated on ultrathin silicon-on-insulator substrates are investigated and compared with reference Si channel devices. The total thickness of the fully depleted Si/SiGe(C)/Si body structure is /spl sim/ 25 nm. All devices demonstrated a near ideal subthreshold behavior, and the drive current and mobility were increased with more than 60% for SiGe and SiGeC channels. When comparing SIMOX and UNIBOND substrates, no significant difference could be detected.     

Drift hole mobility in strained and unstrained doped Si1-xGex alloys

Results of the drift hole mobility in strained and unstrained SiGe alloys are reported for Ge fractions varying from 0 to 30% and doping levels of 10¹⁵-10¹⁹ cm^-3. The mobilities are calculated taking into account acoustic, optical, alloy, and ionized-impurity scattering. The mobilities are then compared with experimental results for a boron doping concentration of 2×10¹⁹ cm^-3. Good agreement between experimental and theoretical values is obtained. The results show an increase in the mobility relative to that of silicon     

Improved self-gain in deep submicrometer strained silicon-germanium pMOSFETs with HfSiOx/TiSiN gate stacks

The self-gain of surface channel compressively strained SiGe pMOSFETs with HfSiO_x/TiSiN gate stacks is investigated for a range of gate lengths down to 55 nm. There is 125% and 700% enhancement in the self-gain of SiGe pMOSFETs compared with the Si control at 100 nm and 55 nm lithographic gate lengths, respectively. This improvement in the self-gain of the SiGe devices is due to 80% hole mobility enhancement compared with the Si control and improved electrostatic integrity in the SiGe devices due to less boron diffusion into the channel. At 55 nm gate length, the SiGe pMOSFETs show 50% less drain induced barrier lowering compared with the Si control devices. Electrical measurements show that the SiGe devices have larger effective channel lengths. It is shown that the enhancement in the self-gain of the SiGe devices compared with the Si control increases as the gate length is reduced thereby making SiGe pMOSFETs with HfSiO_x/TiSiN gate stacks an excellent candidate for analog/mixed-signal applications.