Changes in mass and stress during anodic oxidation and cathodic reduction of the Cu/Cu2O multilayer film

The anodic oxidation and cathodic reduction processes of the Cu/Cu₂O multilayer film and pure Cu film in pH 8.4 borate buffer solution were analyzed by electrochemical quartz crystal microbalance (EQCM) for gravimetry and bending beam method (BBM) for stress measurement. The mass loss of the multilayer film during anodic oxidation at 0.8 V (SHE) in the passive region was less than that of the pure Cu film. The comparison between current transients and mass changes during anodic oxidation has succeeded in separating the anodic current density into two partial current densities of oxide film growth, i_O^2-, and of Cu²⁺ dissolution through the passive film, i_Cu²⁺. As a result, in the case of the pure Cu film, the anodic current density was mainly due to i_Cu²⁺, while in the case of the multilayer film, i_Cu²⁺ was almost equal to i_O^2-. The compressive stress for the multilayer film was generated during anodic oxidation, while the tensile stress for the pure Cu film was generated.The mass loss of the multilayer film during cathodic reduction at a constant current density (i_c = −20 μA cm⁻²) was significantly less than that estimated from coulometry, suggesting that H₂O produced by cathodic reduction remained in the multilayer film. The compressive stress was generated during cathodic reduction of the multilayer film, which was ascribed to H₂O remained in the multilayer film.     

An ultrathin polymer coating of carboxylate self-assembled monolayer adsorbed on passivated iron to prevent iron corrosion in 0.1 M Na2SO4

For preparing an ultrathin two-dimensional polymer coating adsorbed on passivated iron, a 16-hydroxyhexadecanoate ion HO(CH₂)₁₅CO₂⁻ self-assembled monolayer (SAM) was modified with 1,2-bis(triethoxysilyl)ethane (C₂H₅O)₃Si(CH₂)₂Si(OC₂H₅)₃ and octadecyltriethoxysilane C₁₈H₃₇Si(OC₂H₅)₃. Protection of passivated iron against passive film breakdown and corrosion of iron was investigated by monitoring of the open-circuit potential and repeated polarization measurements in an aerated 0.1 M Na₂SO₄ solution during immersion for many hours. The time required for passive film breakdown of the polymer-coated electrode was markedly higher in this solution than that of the passivated one, indicating protection of the passive film from breakdown by coverage with the polymer coating. The protective efficiencies of the passive film covered with the coating were extremely high, more than 99.9% in 0.1 M Na₂SO₄ before the passive film was broken down, showing prominent cooperative suppression of iron corrosion in the solution by coverage with the passive film and polymer coating. The polymer-coated surface was characterized by contact angle measurement and electron-probe microanalysis (EPMA). Prevention of passive film breakdown and iron corrosion for the polymer-coated electrode healed in 0.1 M NaNO₃ was also examined in 0.1 M Na₂SO₄.     

Corrosion and passivation mechanism of chromium diboride coatings on stainless steel

The corrosion resistance of fully crystalline CrB₂ coatings magnetron sputtered onto AISI 316L stainless steel was tested in acidic solutions. CrB₂ coatings showed excellent corrosion protection, but suffered a breakdown when an anodic potential of greater than about +1 V (SHE) was applied to the surface in a 1 M HCl electrolyte. The coating failure at high potentials is attributed to transpassive dissolution of the coating at volume defects, enabling the electrolyte to reach the underlying 316L substrate, resulting in its rapid corrosion and subsequent fracturing of the coating. Electrochemical data and potential-pH (Pourbaix) diagrams, constructed from thermodynamic data, indicate that the corrosion resistance of CrB₂ is due to the formation of a Cr(III) oxide passive film in the absence of activation corrosion.     

Protection of passivated iron against corrosion in a 0.1 M NaNO3 solution by coverage with an ultrathin polymer coating of carboxylate SAM

An ultrathin, ordered and two-dimensional polymer coating was prepared on passivated iron by modification of 16-hydroxyhexadecanoate ion HO(CH₂)₁₅CO₂⁻ self-assembled monolayer (SAM) with 1,2-bis(triethoxysilyl)ethane (C₂H₅O)₃Si(CH₂)₂Si(OC₂H₅)₃ and octadecyltriethoxysilane C₁₈H₃₇Si(OC₂H₅)₃. Protection of passivated iron against passive film breakdown and corrosion of iron was examined by monitoring of the open-circuit potential and repeated polarization measurements in an aerated 0.1 M NaNO₃ solution during immersion for many hours. Passive film breakdown on the polymer-coated electrode in the solution was not observed during immersion for 480 h, whereas that of the passivated one occurred at 18.1 h, indicating protection of the passive film from breakdown by coverage with the polymer coating. The protective efficiencies of the passive film covered with the coating were extremely high, around 99.9% in the initial region of the immersion time up to 72 h and more than 98.3% thereafter, indicating prominent cooperative suppression of iron corrosion in 0.1 M NaNO₃ by coverage with the passive film and polymer coating. The polymer-coated surface was characterized by contact angle measurement and electron-probe microanalysis.     

Long-term anticorrosion behaviour of polyaniline on mild Steel

Anticorrosion performances of polyaniline emeraldine base/epoxy resin (EB/ER) coating on mild steel in 3.5% NaCl solutions of various pH values were investigated by electrochemical impedance spectroscopy (EIS) for 150 days. In neutral solution (pH 6.1), EB/ER coating offered very efficient corrosion protection with respect to pure ER coating, especially when EB content was 5-10%. The impedance at 0.1 Hz of the coating increased in the first 1-40 immersion days and then remained constant above 10⁹ Ω·cm² until 150 days, which in combination with the observation of a Fe₂O₃/Fe₃O₄ passive film formed on steel confirmed that the protection of EB was mainly anodic. In acidic or basic solution (pH 1 or 13), EB/ER coating also performed much better than pure ER coating. However, these media weakened the corrosion resistance due to breakdown of the passive film or deterioration of the ER binder.     

XPS analysis of the passive film formed on austenitic stainless steel coated with conductive polymer

Improvement of the passivation behavior of Type 304 austenitic stainless steel (SS) by coating with conductive polymers (CPs), like polyaniline (PANI) and poly(o-phenylenediamine) (PoPD), followed by exposure in an acid solution has been demonstrated. The passive films formed on SSs (after peeling off the polymer layer) are compared with those formed during anodic polarization under the same exposure condition. The passive films beneath the CPs are thicker and less hydrated than those formed on uncoated stainless steel. The polymer layer enhances the enrichment of chromium and nickel in the entire passive oxide, forming a more protective film than that formed during anodic polarization. The elemental distribution within the passive film is different in the two modes of passivation. The type of the polymer influences on the composition of the passive film. The best passivation is obtained by PoPD, with the passive film resulting in significant resistance of the SS to pitting corrosion in the 3% NaCl solution. The oxide film of this steel is characterized, in its inner and outer layers, by the highest ratio of Cr(OH)₃/Cr₂O₃ and the lowest content of iron species.     

The structure and high temperature corrosion performance of medium-thickness aluminide coatings on nickel-based superalloy GTD-111

Simple and Si-modified aluminide coatings having medium-thickness (40-60 μm) have been applied on the superalloy GTD-111 by a slurry technique. Hot corrosion and cyclic oxidation performance of the uncoated and the coated superalloy were investigated by exposing samples to a molten film of Na₂SO₄-40 %wt NaVO₃-10%wt NaCl at 780 °C and 1 h cyclic oxidation at 1100 °C in air, respectively. The presence of silicon in the aluminide structure increased the oxidation resistance by a factor of 1.7 times. In addition, a SiO₂-containing scale, which formed on the Si-containing coating surface, was stable during of the hot corrosion testing.     

Optimization of Cr/Mo molar ratio in FeCoCrMoCBY alloys for high corrosion resistance

The corrosion behavior of bulk metallic glasses (BMGs) (Fe₄₁Co₇Cr₁₅Mo₁₄C₁₅B₆Y₂)_100–xCr_x (x=0, 4, 8, 12, molar fraction, %) was investigated in 1 mol/L HCl aqueous solution with electrochemical tests. The electrochemical measurements demonstrate that the passive current density of Fe-based amorphous alloy is reduced by about one order of magnitude, and meanwhile, the stability of passive film can be guaranteed by the Cr/Mo molar ratio. The Mott–Schottky (M–S) curves show that the passive film is the densest when the molar ratio of Cr/Mo is between 1.37 and 1.69. X-ray photoelectron spectroscopy (XPS) analysis was performed to clarify chemical states of elements in the passive films. The results show that the corrosion resistance of the alloy is related to the molar ratio of Cr/Mo. The stability of passive film is determined by the synergistic action of Cr and Mo elements. The main component of the passive film is Cr³⁺ oxide. When the potential is greater than 0.5 V (vs SCE), Mo⁶⁺ ions play an important role in keeping the stability of the passive film. The appropriate molar ratio of Cr/Mo can reduce the dissolution rate of the passive film.     

Comparative study of Cr3C2-NiCr coatings obtained by HVOF and hard chromium coatings

In the present work the corrosion resistance of micro-cracked hard chromium and Cr₃C₂-NiCr (HVOF) coatings applied on a steel substrate have been compared using open-circuit potential (E_OC) measurements, electrochemical impedance spectroscopy (EIS) and polarization curves. The coatings surfaces and cross-section were characterized before and after corrosion tests using optical microscopy (OM) and scanning electron microscopy (SEM). After 18 h of immersion, the open-circuit potential values were around −0.50 and −0.25 V/(Ag∣AgCl∣KCl_sat) for hard chromium and Cr₃C₂-NiCr, respectively. The surface analysis done after 12 h of immersion showed iron on the hard chromium surface inside/near surface cracks, while iron was not detected on the Cr₃C₂-NiCr surface even after 18 h. For longer immersion time hard chromium was more degraded than thermal sprayed coating. For hard chromium coating a total resistance values between 50 and 80 kΩ cm² were measured and two well-defined time constants were observed, without significant change with the immersion time. For Cr₃C₂-NiCr coating the total impedance diminished from around 750 to 25 kΩ cm² as the immersion time increased from 17 up to 132 h and two overlapped time constants were also observed. Polarization curves recorded after 18 h of immersion showed a lower current and higher corrosion potential for Cr₃C₂-NiCr coating than other samples studied.     

阳极氧化法制备TiO2膜在模拟深海热液区的耐腐蚀性能

以恒压阳极氧化方法在钛基体上制备TiO₂氧化膜,使用水热釜模拟深海热液区的条件研究其耐腐蚀性能。采用XRD、SEM、接触角测定仪对氧化膜以及腐蚀试样产物进行晶型、表面结构、化学成分和亲疏水性能测定,使用动电位扫描方法对其进行极化曲线测试。结果表明,钛试样和阳极氧化钛试样在模拟深海环境条件下,经过腐蚀反应在表面都生成了一层非致密的TiO₂ 膜,对基体并不能起到保护作用,而阳极氧化生成的致密TiO₂ 膜对基体能够起到很好的保护作用。经腐蚀后钛试样表面有TiH₂相的形成,腐蚀电位负移0.45 V。而阳极氧化钛试样表面没有TiH₂相的形成,且腐蚀电位负移较小,表现出良好的耐腐蚀性能。     

Application of polyaniline to galvanic anodic protection on stainless steel in H2SO4 solutions

A stand-alone polyaniline (PANI) film electrode was made and then applied to protect 1Cr13 stainless steel (a type of stainless steel typically used in China, 0–15% C, 13% Cr) from corrosion in highly acidic solution, up to 5 M H₂SO₄. The stand-alone PANI electrode and 1Cr13 were coupled to study their galvanic interactions. PANI is a cathode while 1Cr13 is an anodic. The results indicate that PANI with a certain area can quickly passivate the stainless steel and effectively maintain the steady passive state for a long period of time. This specific method of PANI preventing 1Cr13 from corrosion is called galvanic anodic protection (GAP). Moreover, the efficiency, mechanism, and security of GAP were discussed. The results demonstrate that the stand-alone PANI electrode may have a potential application to galvanic anodic protection on stainless steel in highly corrosive H₂SO₄ solutions.     

Effects of Na2SiO3 on anodization of Mg-Al-Zn alloy in 3 M KOH solution

The anodic behavior of Mg-Al-Zn alloy (AZ91D) under low potential electrolysis in 3 M KOH solutions was studied with and without addition of 0.5-5 M Na₂SiO₃. Anodic films incorporating silicon were formed during electrolysis, and the films formed under constant potential electrolysis at 4 V in 3 M KOH solution with Na₂SiO₃ were uniform and thicker than the films formed without Na₂SiO₃. A few at% of silicon was present as Mg₂SiO₄ in the films, although the main compound was Mg(OH)₂. The corrosion resistance of the films formed in solutions with Na₂SiO₃ increased in an anodic polarization test in 0.1 M KCl solution.     

Corrosion prevention of passivated iron in 0.1 M NaCl by coverage with an ultrathin polymer coating and healing treatment in 0.1 M NaNO3

An ultrathin, ordered and two-dimensional polymer coating was prepared on a passivated iron electrode by modification of 16-hydroxyhexadecanoate ion HO(CH₂)₁₅CO₂⁻ self-assembled monolayer with 1,2-bis(triethoxysilyl)ethane (C₂H₅O)₃Si(CH₂)₂Si(OC₂H₅)₃ and octadecyltriethoxysilane C₁₈H₃₇Si(OC₂H₅)₃. Subsequently, the electrode was healed in 0.1 M NaNO₃. Protection of passivated iron against passive film breakdown and corrosion of iron was examined by monitoring of the open-circuit potential and repeated polarization measurements of the polymer-coated and healed electrode in an aerated 0.1 M NaCl solution during immersion for many hours. Localized corrosion was markedly prevented by coverage with the polymer coating and the healing treatment in 0.1 M NaNO₃. Prominent protection of iron from corrosion in 0.1 M NaCl was observed before the breakdown occurred. The electrode surface covered with the healed passive film and polymer coating was analyzed by contact angle measurement, X-ray photoelectron spectroscopy and electron-probe microanalysis.     

Self-healing mechanism of a protective film prepared on a Ce(NO3)3-pretreated zinc electrode by modification with Zn(NO3)2 and Na3PO4

Self-healing mechanism of a protective film against corrosion of zinc at scratches in an aerated 0.5 M NaCl solution was investigated by polarization measurements, X-ray photoelectron spectroscopy (XPS) and electron-probe microanalysis (EPMA). The film was prepared on a zinc electrode by treatment in a Ce(NO₃)₃ solution and addition of aqueous solutions containing 9.98 or 19.9 μg/cm² of Zn(NO₃)₂ · 6H₂O and 55.2 μg/cm² of Na₃PO₄ · 12H₂O. After the coated electrode was scratched with a knife-edge crosswise and immersed in the NaCl solution for many hours, polarization measurements, observation of pit formation at the scratches, XPS and EPMA were carried out. This film was remarkably protective and self-healing against zinc corrosion on the scratched electrode. The cathodic and anodic processes of zinc corrosion were markedly suppressed by coverage of the surface except for scratches with a thin Ce₂O₃ layer containing a small amount of Ce⁴⁺ and the surface of scratches with a layer composed of Zn₃(PO₄)₂ · 4H₂O, Zn(OH)₂ and ZnO mostly.     

The electrochemical behavior of austenitic stainless steel with different degrees of sensitization in the transpassive potential region in 1 M H2SO4 containing chloride

This paper investigates electrochemical methods to estimate the degree of sensitization (DOS) for as-rolled and solution-treated austenitic stainless steels (AISI 304). The change in DOS was introduced by heat treatment of various time periods at 700 °C, and the electrochemical experiments were conducted at 27 °C in 1 M H₂SO₄ + 0.2 wt.% NaCl. The results show that there is no obvious difference in the anodic polarization curves of the specimens with the differences in DOS. However, the DOS of specimens can be clearly differentiated with AC impedance response in a particular transpassive potential region. In the transpassive potential region of the anodic polarization curve, as overpotential is increased beyond the breakdown potential, three types of anodic dissolution, passive dissolution, grain-boundary attack, and pitting can be characterized. The DOS can only be correctly evaluated with AC impedance response in the middle of the transpassive potential region, where anodic dissolution is of grain-boundary attack type, from 1.05 to 1.1 V. The chromium-depleted zone was preferentially attacked and an intergranular corrosion was found for the serious sensitized specimen after AC impedance test. The healing effect was observed in as-rolled specimens as the specimens were heated more than 72 h, but the effect was not found in the solution-treated specimens sensitized for up to 480 h at 700 °C.     

Passivity of stainless steel in sulphuric acid under chemical oxidation

The main purpose of the present work was to study the passivity of stainless steel in sulphuric acid under chemical oxidation with H₂O₂ solution. Potentiodynamic polarisation and open circuit potential (OCP) measurements indicated that H₂O₂ facilitates the increase of OCP of stainless steel which shifts from active region into passive region. The X-ray photoelectron spectroscopy results suggested that a passive film, composed of oxyhydroxides, Cr₂O₃, Cr(VI) species, NiO, and sulphate (FeSO₄, Cr₂(SO₄)₃·xH₂O), is achieved after H₂SO₄–H₂O₂ passivation. The passive mechanism under H₂O₂ oxidation was discussed and the corrosion resistance of passive film was compared with that of the passive films produced by HNO₃ passivity and H₂SO₄ potentiostatic passivity. The results of electrochemical impedance spectroscopy, cyclic voltammetry, and anodic polarisation experiments confirmed that the chemical oxidation with H₂O₂ solution is capable of improving the corrosion resistance of stainless steel significantly and the passive film is more stable than those produced by other passivating methods.     

Microstructure and corrosion properties of plasma-sprayed NiCr-Cr3C2 coatings comparison with different post treatment

The effects of laser and plasma arc remelting on the microstructure and properties of plasma-sprayed NiCr-Cr₃C₂ coatings on steel substrates have been investigated. The microstructure of the coatings has been analyzed by X-ray diffraction (XRD) and scanning electron microscope (SEM). It is found that the Cr₃C₂, δ-(Cr,Ni), Cr₇C₃ and Cr₂₃C₆ phases were obtained for both coatings, before and after remelting treatment. The laser remelting was operated in a continuous way with 800 W power in different scan speed, while the plasma arc remelting was operated with a plasma cladding machine under different scan currents. However, the denser microstructure of both remelted coatings can be obtained, especially for the plasma arc remelted coating. The Vickers microhardness measurement showed certain enhancement values for both remelted coatings. The corrosion behavior was evaluated through salt spray corrosion (SSC) method. Energy-dispersive spectroscopy (EDS) showed that the chloride was produced during SSC process. The higher corrosion resistance for plasma arc remelted coating may be due to the more compact microstructure, less porosity rate and tensile residual stress. Compared with laser remelting method, plasma arc remelting is a cheap, convenient and effective remelting method.     

Microstructure and corrosion resistance of Cr/Cr2N multilayer film deposited on the surface of depleted uranium

Depleted uranium is widely used in national defence and nuclear energy fields. However, the inferior corrosion resistance limits its application. A Cr/Cr₂N film was prepared by magnetron sputtering on the uranium to improve its corrosion resistance. The Cr/Cr₂N film exhibits modulation structure. The introduction of the Cr/Cr₂N increases the corrosion potential; the corresponding current density decreases about three orders of magnitude. After polarization corrosion, the surface morphology of the Cr/Cr₂N-coated on uranium keeps integrated. Only a thin layer of film (∼40 nm) is oxidized. The Cr/Cr₂N film shows great potential in improving oxidation and corrosion resistance of depleted uranium.     

Passivity and passivity breakdown of zinc anode in alkaline medium

The electrochemical behaviour of zinc in NaOH solutions has been investigated by using potentiodynamic technique and complemented by X-ray analysis. The E/i curves exhibit active, passive and transpassive regions prior to oxygen evolution. The active region displays two anodic peaks. The passivity is due to the Formation of a compact Zn(OH)₂ film on the anode surface. The transpassive region is assigned to the electroformation of ZnO₂. The reverse sweep shows an activation anodic peak and one catholic peak prior to hydrogen evolution. The influence of increasing additives of NaCl, NaBr and Nal on the anodic behaviour of zinc in NaOH solutions has been studied. The halides stimulate the active dissolution of zinc and tend to break down the passive film, leading to pitting corrosion. The aggressiveness of the halide anions towards the stability of the passive film decreases in the order: I^? > Br^? > Cl^?. The susceptibility of zinc anode to pitting corrosion enhances with increasing the halide ion concentration but decreases with increasing both the alkali concentration and the sweep rate.     

Effect of porosity sealing treatments on the corrosion resistance of high-velocity oxy-fuel (HVOF)-sprayed Fe-based amorphous metallic coatings

High-velocity oxy-fuel-sprayed FeCrMoMnWBCSi amorphous metallic coatings were sealed with sodium orthosilicate (Na₃SiO₄), aluminium phosphate (AlPO₄), and cerium salt sealants. The microstructure of the sealed coatings was characterised by scanning electron microscopy, energy dispersive spectrometer, and X-ray diffraction. Corrosion behaviour was examined using electrochemical methods of potentiodynamic polarisation, cyclic polarisation, electrochemical impedance spectroscopy, and Mott-Schottky tests. The results indicated that the uniform corrosion resistance of the three sealed coatings was enhanced greatly, and the passive current densities were decreased by one order of magnitude after the sealing treatments. The AlPO₄ sealant can penetrate the coatings by no less than 50 μm and enhance their hardness, which exhibited a more uniform corrosion resistance, fairly good pitting corrosion resistance, and can be applied in long-term corrosive and/or abrasive environments. The cerium salt-sealed coating showed better pitting corrosion resistance but inferior corrosion resistance in the local regions of micro-cracks, which was practically used for temporary corrosion protection. The Na₃SiO₄-sealed coating showed better uniform corrosion resistance and inferior pitting corrosion resistance, which can be applied in short-term corrosion environments. The stability of the passive film affected the corrosion behaviour of the sealed coatings. The AlPO₄-sealed coating performed better as a protective passive film during the long-term immersion test for a lower defect concentration and a more protective passive film.