共查询到20条相似文献,搜索用时 125 毫秒
1.
变电所二次系统电磁兼容抗扰度指标分析 总被引:3,自引:2,他引:1
变电所的电磁环境威胁二次系统的安全运行,处于强电磁环境中的变电所内的二次系统进行电磁兼容抗扰度测试尤为重要。为此,根据国内外变电所电磁环境测量及分析结果,总结了变电所电磁环境参数的特征值并提出变电所二次系统电磁环境参数的推荐值,包括工频电场、稳定持续磁场、1~3s短时磁场、雷电瞬态磁场、操作瞬态电场、操作瞬态磁场、雷电干扰电压、操作干扰电压、短路干扰电压、瞬态地电位升和工频短路地电位升。分析比较目前变电所内二次系统的常规电磁兼容抗扰度的要求后,提出了变电所二次设备电磁兼容抗扰度的要求,并分析讨论了不同位置的二次设备电磁兼容抗扰度测试的主要特征参数推荐值,另外也补充了需要增加的试验项目。提出的二次系统抗扰度测试参数更为符合变电站电磁环境实际特征。 相似文献
2.
本文分三个单元介绍车辆用电子设备的电磁性试验,其中第一部分是静电放电试验;第二部分是传导发射和传导抗扰度试验;第三部分是电瞬变干扰的抗扰度的试验。 相似文献
3.
4.
复杂的电磁环境中,电力电子装置在运行时产生的电磁干扰问题越来越严重,从而对系统本身提出了更为严格的要求,其中传导电磁抗扰度的定量预测和有效抑制问题成为一个技术难题。本文面向电力电子设备的电磁抗扰度问题,做了一次尝试,以开关电源(型号为NET-50B)为例,在空载和带电阻负载两种情况下,对其进行传导抗扰度试验,通过耦合/去耦网络将干扰电压(140 d BμV)注入开关电源,测试不同频率下其输出端电压稳定情况,并利用频谱分析仪对测试过程中产生的辐射场进行了监测。通过测试,得到了该型号开关电源的电磁抗扰度情况,验证了该测试方法的有效性,对电力电子设备传导电磁抗扰度的预测分析具有重要意义。 相似文献
5.
6.
7.
8.
9.
10.
针对继电保护装置的工频磁场抗扰度问题,阐述了工频磁场实验,分析了工频磁场骚扰的形成机理,介绍了工频磁场对继电保护装置的影响和重要性,最后阐述了工频磁场抗干扰设计的难点,并提出了一些抗干扰设计手段和异常问题处理措施,对于继电保护装置的工频磁场试验问题及回路抗干扰设计有一定的参考意义。 相似文献
11.
12.
13.
Yuan Chen Westergard L. Mojarradi M.M. Johnson T.W. Cozy R.S. Billman C. Burke G.R. Kolawa E.A. 《Device and Materials Reliability, IEEE Transactions on》2006,6(2):146-153
A design for reliability methodology has been developed for electronics for low-temperature applications. A hot carrier aging (HCA) lifetime projection model is proposed to take into account the HCA impact on technology, analysis of parametric degradation versus critical circuit path degradation, transistor bias profile, transistor substrate current profile, and operating temperature profile. The most applicable transistor size can be determined in order to meet the reliability requirements of the electronics operating under low temperatures. This methodology and approach can also be applied to other transistor-level failure and/or degradation mechanisms for applications with varying temperature ranges. 相似文献
14.
15.
《Power Delivery, IEEE Transactions on》1998,13(1):73-77
IEEE Standard 1344, Synchrophasors for Power Systems, was completed in 1995. It sets parameters required to ensure that phasor measurement will be made and communicated in a consistent manner. It specifies requirements for the timing signal used for phasor synchronization and the time code needed for input to a measurement unit. GPS is the recommended time source and IRIG-B is the basic format used for time communication. The standard requires correlating phasors computed from unsynchronized and synchronized sampling to a common basis. Timetagging accurately and consistently is essential for wide area comparison of phase. The standard specifies information exchange and control message formats. These include data output, configuration, and command messages. It includes 7 annexes that discuss the concepts covered in the body of the standard 相似文献
16.
17.
18.
19.
20.
分析了GIS断路器故障原因,介绍了检验过程与充气检查、监督情况,并提供一些可借鉴的成功经验。 相似文献