Ultrahigh interference spatial compression of light inside the subwavelength aperture of a near-field optical probe

Spatial effects of interference and interaction of light modes in the subwavelength part of the near-field optical microscopy probe have been theoretically studied. It was found that the mode interference can lead to higher spatial compression of light (wavelength is equal to 500 nm in free space) within the transverse size of 25 nm inside the probe output aperture of 100 nm in diameter. The results predict a principal possibility of higher spatial resolution in the near-field optical microscopy technique.     

Extraordinary optical transmission brightens near-field fiber probe

Near-field scanning optical microscopy (NSOM) offers high optical resolution beyond the diffraction limit for various applications in imaging, sensing, and lithography; however, for many applications the very low brightness of NSOM aperture probes is a major constraint. Here, we report a novel NSOM aperture probe that gives a 100× higher throughput and 40× increased damage threshold than conventional near-field aperture probes. These brighter probes facilitate near-field imaging of single molecules with apertures as small as 45 nm in diameter. We achieve this improvement by nanostructuring the probe and by employing a novel variant of extraordinary optical transmission, relying solely on a single aperture and a coupled waveguide. Comprehensive electromagnetic simulations show good agreement with the measured transmission spectra. Due to their significantly increased throughput and damage threshold, these resonant configuration probes provide an important step forward for near-field applications.     

Nature of light scattering in dental enamel and dentin at visible and near-infrared wavelengths

The light-scattering properties of dental enamel and dentin were measured at 543, 632, and 1053 nm. Angularly resolved scattering distributions for these materials were measured from 0° to 180° using a rotating goniometer. Surface scattering was minimized by immersing the samples in an index-matching bath. The scattering and absorption coefficients and the scattering phase function were deduced by comparing the measured scattering data with angularly resolved Monte Carlo light-scattering simulations. Enamel and dentin were best represented by a linear combination of a highly forward-peaked Henyey-Greenstein (HG) phase function and an isotropic phase function. Enamel weakly scatters light between 543 nm and 1.06 μm, with the scattering coefficient (μ(s)) ranging from μ(s) = 15 to 105 cm(-1). The phase function is a combination of a HG function with g = 0.96 and a 30-60% isotropic phase function. For enamel, absorption is negligible. Dentin scatters strongly in the visible and near IR (μ(s)?260 cm(-1)) and absorbs weakly (μ(a) ? 4 cm(-1)). The scattering phase function for dentin is described by a HG function with g = 0.93 and a very weak isotropic scattering component (? 2%).     

A study of light collection efficiency in scintillation detectors

A group of computer programs was set up to study the light of collection efficiency in scintillation detectors with rectangular cross sections. The input conditions can be chosen arbitrarily, including: the size, light attenuation length and refraction index of the scintillator and light guide, the refraction index of the coupling medium, the reflection characteristics of the walls, and the position of light sources. A few examples are discussed in this article.     

Reproducible fabrication of a fiber probe with a nanometric protrusion for near-field optics

We propose a new type of fiber probe with a nanometric protruding tip emerging from a metal film and describe a novel method, called the selective resin-coating method, for fabricating such probes. It is a reproducible etching process consisting of four steps and can be applied to silica fibers sharpened by selective chemical etching. With this method, we obtained tips with the apex diameter and the foot diameter of the protrusion being less than 10 and 30 nm, respectively, when the gold film was ~120 nm thick.     

Experimental realization of optical lumped nanocircuits at infrared wavelengths

The integration of radiofrequency electronic methodologies on micro- as well as nanoscale platforms is crucial for information processing and data-storage technologies. In electronics, radiofrequency signals are controlled and manipulated by 'lumped' circuit elements, such as resistors, inductors and capacitors. In earlier work, we theoretically proposed that optical nanostructures, when properly designed and judiciously arranged, could behave as nanoscale lumped circuit elements--but at optical frequencies. Here, for the first time we experimentally demonstrate a two-dimensional optical nanocircuit at mid-infrared wavelengths. With the guidance of circuit theory, we design and fabricate arrays of Si3N4 nanorods with specific deep subwavelength cross-sections, quantitatively evaluate their equivalent impedance as lumped circuit elements in the mid-infrared regime, and by Fourier transform infrared spectroscopy show that these nanostructures can indeed function as two-dimensional optical lumped circuit elements. We further show that the connections among nanocircuit elements, in particular whether they are in series or in parallel combination, can be controlled by the polarization of impinging optical signals, realizing the notion of 'stereo-circuitry' in metatronics-metamaterials-inspired optical circuitry.     

Fiber-optic probe for noninvasive real-time determination of tissue optical properties at multiple wavelengths

We present a compact, fast, and versatile fiber-optic probe system for real-time determination of tissue optical properties from spatially resolved continuous-wave diffuse reflectance measurements. The system collects one set of reflectance data from six source-detector distances at four arbitrary wavelengths with a maximum overall sampling rate of 100 Hz. Multivariate calibration techniques based on two-dimensional polynomial fitting are employed to extract and display the absorption and reduced scattering coefficients in real-time mode. The four wavelengths of the current configuration are 660, 785, 805, and 974 nm, respectively. Cross-validation tests on a 6 x 7 calibration matrix of Intralipid-dye phantoms showed that the mean prediction error at, e.g., 785 nm was 2.8% for the absorption coefficient and 1.3% for the reduced scattering coefficient. The errors are relative to the range of the optical properties of the phantoms at 785 nm, which were 0-0.3/cm for the absorption coefficient and 6-16/cm for the reduced scattering coefficient. Finally, we also present and discuss results from preliminary skin tissue measurements.     

Compound parabolic concentrator probe for efficient light collection in spectroscopy of biological tissue

We describe a compound parabolic concentrator (CPC)-based probe for enhanced signal collection in the spectroscopy of biological tissues. Theoretical considerations governing signal enhancement compared with conventional collection methods are given. A ray-tracing program was used to analyze the throughput of CPC's with shape deviations and surface imperfections. A modified CPC shape with 99% throughput was discovered. A 4.4-mm-long CPC was manufactured and incorporated into an optical fiber-based near-infrared Raman spectrometer system. For human tissue samples, light collection was enhanced by a factor of 7 compared with collection with 0.29-NA optical fibers.     

Temperature dependence of light absorption in water at holmium and thulium laser wavelengths

A simple experimental setup is described that facilitates accurate measurements of the temperature-dependent water absorption coefficient in the mid-infrared spectral region. With this setup, the absorption of holmium and thulium laser radiation in water was quantified to a precision of 0.5%. In the 20-100 degrees C temperature range, a linear decrease of the absorption coefficient with temperature is observed. The slope coefficients amount to -0.104 +/- 0.001 and -0.259 +/- 0.003 l/(K cm) for 2090-nm holmium and 2014-nm thulium radiation, respectively. At both wavelengths, this bleaching reduces the absorption coefficients of water at 100 degrees C by one third when compared with room temperature. A numerical simulation shows that the variable absorption has a noticeable influence on peak temperatures in laser heating of water.     

基于HFSS的孔阵机壳近场屏蔽效能分析

机载电子设备之间的间距很小,而且通常有用于散热的功能性孔阵,容易造成电磁泄漏,必须进行近场屏蔽效能分析.对比分析了采用有限元法的HFSS和传输线法计算孔阵近场屏蔽效能的结果,理论分析和计算结果均表明,传输线法不适合用于近场屏蔽效能计算.基于HFSS仿真分析,研究了相关参数对近场屏效的影响规律,提出了提高近场屏效的设计方...     

Fluorescence efficiency and visible re-emission spectrum of tetraphenyl butadiene films at extreme ultraviolet wavelengths

A large number of current and future experiments in neutrino and dark matter detection use the scintillation light from noble elements as a mechanism for measuring energy deposition. The scintillation light from these elements is produced in the extreme ultraviolet (EUV) range, from 60 to 200 nm. Currently, the most practical technique for observing light at these wavelengths is to surround the scintillation volume with a thin film of tetraphenyl butadiene (TPB) to act as a fluor. The TPB film absorbs EUV photons and re-emits visible photons, detectable with a variety of commercial photosensors. Here we present a measurement of the re-emission spectrum of TPB films when illuminated with 128, 160, 175, and 250 nm light. We also measure the fluorescence efficiency as a function of incident wavelength from 120 to 250 nm.     

Simple measuring technique for the diffraction efficiency of slanted volume gratings at various wavelengths

To measure diffraction efficiencies of gratings as a function of wavelength, it is necessary to have quasi-monochromatic light sources of various wavelengths. We propose a method to measure the wavelength dependence of the grating diffraction efficiency by using a quasi-monochromatic light source. This method of estimating the real diffraction characteristics of the gratings for various wavelengths is very useful and simple. First the diffraction efficiency of the grating as a function of various incident-beam angles of monochromatic light is measured, then, using these data, we can obtain the diffraction efficiencies for various wavelengths of the same incident angle of light by virtue of a mathematical-conversion method. The mathematical-conversion results for two laminated differently slanted angle gratings of the same volume grating period are in good agreement with the experimental ones.     

Optical properties of microfabricated fully-metal-coated near-field probes in collection mode

A study of the optical properties of microfabricated, fully-metal-coated quartz probes collecting longitudinal and transverse optical fields is presented. The measurements are performed by raster scanning the focal plane of an objective, focusing azimuthally and radially polarized beams by use of two metal-coated quartz probes with different metal coatings. A quantitative estimation of the collection efficiencies and spatial resolutions in imaging both longitudinal and transverse fields is made. Longitudinally polarized fields are collected with a resolution approximately 1.5 times higher as compared with transversely polarized fields, and this behavior is almost independent of the roughness of the probe's metal coating. Moreover, the coating roughness is a critical parameter in the relative collection efficiency of the two field orientations.     

Replication of a holographic ion-etched spherical blazed grating for use at extreme-ultraviolet wavelengths: efficiency

Using synchrotron radiation, we have measured the efficiency at an angle of incidence of 10 degrees of a holographic ion-etched spherical blazed grating and three of its fourth-generation replicas. The measured efficiency profile of replicas 1 and 3 prior to multilayer coating oscillated from thin-film interference produced by the replicas' Al/Al2O3/SiO2 structure. A Mo2C/Si multilayer coating was applied to the master grating and replicas 1 and 2. After coating, the maximum grating efficiency occurred in the -2nd order and the maximum values were 12.4% at 143.8 angstroms for the master and 11.6% at 145.2 angstroms for replicas 1 and 2. On the basis of measurements obtained after coating, the derived groove efficiency was 22.2% for the master, 19.4% for replica 1, and 19.3% for replica 2. The groove efficiency of the uncoated replica 3 was 24.3% at 142.5 angstroms. We find that the replicas are reasonably faithful copies of the ion-etched master, and models based on measured atomic force microscope groove profiles are in general agreement with measured results. However, subtle issues remain regarding the widths of the peak order profile and the location of its maximum wavelength.     

Highly selective sorting of semiconducting single wall carbon nanotubes exhibiting light emission at telecom wavelengths

Single wall carbon nanotubes (SWNTs) are known for their exceptional electronic properties.However,most of the synthesis methods lead to the production of a mixture of carbon nanotubes having different chiralities associated with metallic (m-SWNTs) and semiconducting (s-SWNTs) characteristics.For application purposes,effective methods for separating these species are highly desired.Here,we report a protocol for achieving a highly selective separation of s-SWNTs that exhibit a fundamental optical transition centered at 1,550 nm.We employ a polymer assisted sorting approach,and the influence of preparation methods on the optical and transport performances of the separated nanotubes is analyzed.As even traces of m-SWNTs can critically affect performances,we aim to produce samples that do not contain any detectable fraction of residual m-SWNTs.     

Detection of probe dither motion in near-field scanning optical microscopy

The probe-to-sample separation in near-field scanning optical microscopes can be regulated by a noncontact shear-force sensing technique. The technique requires the measurement of a minute dither motion applied to the probe. We have characterized an optical detection method for measuring this motion to determine the optimum detection configuration in terms of sensitivity and stability. A scalar diffraction model of the detection method is developed for calculating sensitivity, and experimental results are found to be in good agreement with the theoretical predictions. We find that maximum sensitivity and stability cannot be achieved simultaneously, and it may be desirable in practice to trade sensitivity for enhanced stability.     

Determination of optical probe interrogation field of near-infrared reflectance: phantom and Monte Carlo study

An optical probe used to localize human brain tissues in vivo has been reported previously. It was able to sense the underlying tissue structure with an optical interrogation field, termed as "look ahead distance" (LAD). A new side-firing probe has been designed with its optical window along its side. We have defined the optical interrogation field of the new side probe as "look aside distance" (LASD). The purpose of this study is to understand the dependence of the LAD and LASD on the optical properties of tissue, the light source intensity, and the integration time of the detector, using experimental and computational methods. The results show that a decrease in light intensity does decrease the LAD and LASD and that an increase in integration time of detection may not necessarily improve the depths of LAD and LASD. Furthermore, Monte Carlo simulation results suggest that the LAD/LASD decreases with an increase in reduced scattering coefficient to a point, after which the LAD/LASD remains constant. We expect that an optical interrogation field of a tip or side probe is approximately 1-2 mm in white matter and 2-3.5 mm in gray matter. These conclusions will help us optimally manipulate the parameter settings during surgery and determine the spatial resolution of the probe.