Sliding wear characteristics of plasma-sprayed Al2O3 and Cr2O3 coatings against copper alloy under severe conditions

Al₂O₃ and Cr₂O₃ coatings were deposited by atmospheric plasma spraying and their tribological properties dry sliding against copper alloy were evaluated using a block-on-ring configuration at room temperature. It was found that the wear resistance of Al₂O₃ coating was superior to that of the Cr₂O₃ coating under the conditions used in the present study. This mainly attributed to its better thermal conductivity of Al₂O₃ coating, which was considered to effectively facilitate the dissipation of tribological heat and alleviate the reduction of hardness due to the accumulated tribological heat. As for the Al₂O₃ coating, the wear mechanism was plastic deformation along with some micro-abrasion and fatigue-induced brittle fracture, while the failure of Cr₂O₃ coating was predominantly the crack propagation-induced detachment of transferred films and splats spallation.     

Comparison of wear behaviour of plasma-sprayed Al2O3 coatings with and without laser treatment

This paper studies experimentally the effects of CO₂ laser-treatment on the wear behaviour of plasma-sprayed Al₂O₃ coatings, in linear contact sliding (dry, abrasive and lubricated) against SAE 4620 steel. Tests were carried out using a block-on-ring friction and wear tester, under different loads at different speeds. The wear mechanism and the changes in adherence, porosity and microstructure by laser treatment were also investigated. Results show a better wear behaviour for both laser-treated ceramic coating and its paired steel under dry and abrasive conditions, compared with the case without laser treatment. The lubricated wear behaviour of the laser-treated ceramic coating, however, is not improved. The changes in microhardness, porosity and adherence caused by the laser treatment are responsible for the change in wear behaviour of the ceramic coating.     

A study on friction and wear characteristics of nanometer Al2O3 /PEEK composites under the dry sliding condition

The friction and wear properties of the polyetheretherketone (PEEK) based composites filled with 5 mass% nanometer or micron Al₂O₃ with or without 10 mass% polytetrafluroethylene (PTFE) against the medium carbon steel (AISI 1045 steel) ring under the dry sliding condition at Amsler wear tester were examined. A constant sliding velocity of 0.42 m s⁻¹ and a load of 196 N were used in all experiments. The average diameter 250 μm PEEK powders, the 15 or 90 nm Al₂O₃ nano-particles or 500 nm Al₂O₃ particles and/or the PTFE fine powders of diameter 50 μm were mechanically mixed in alcohol, and then the block composite specimens were prepared by the heat compression moulding. The homogeneously dispersion of the Al₂O₃ nano-particles in PEEK matrix of the prepared composites was analyzed by the atomic force microscopy (AFM). The wear testing results showed that nanometer and micron Al₂O₃ reduced the wear coefficient of PEEK composites without PTFE effectively, but not reduced the friction coefficient. The filling of 10 mass% PTFE into pure PEEK resulted in a decrease of the friction coefficient and the wear coefficient of the filled composite simultaneously. However, when 10 mass% PTFE was filled into Al₂O₃/ PEEK composites, the friction coefficient was decreased and the wear coefficient increased. The worn scars on the tested composite specimen surfaces and steel ring surfaces were observed by scanning electron microscopy (SEM). A thin, uniform, and tenacious transferred film on the surface of the steel rings against the PEEK composites filled with 5 mass% 15 nm Al₂O₃ particles but without PTFE was formed. The components of the transferred films were detected by energy dispersive spectrometry (EDS). The results indicated that the nanometer Al₂O₃ as the filler, together with PEEK matrix, transferred to the counterpart ring surface during the sliding friction and wear. Therefore, the ability of Al₂O₃ to improve the wear resistant behaviors is closely related to the ability to improve the characteristics of the transfer film.     

Wear behaviour of Al/(Al2O3p+SiCp) hybrid composites

In this study, dry sliding metal–metal and metal–abrasive wear behaviours of the aluminium matrix hybrid composites produced by pressure infiltration technique were investigated. These composites were reinforced with 37 vol% Al₂O₃ and 25 vol% SiC particles and contained up to 8 wt% Mg in their matrixes. While matrix hardness and compression strength increased, amount of porosity and impact toughness decreased with increasing Mg content of the matrix. Metal–metal and metal–abrasive wear tests revealed that wear resistance of the composites increased with increasing Mg addition. On the other hand, abrasive resistance decreased with increasing test temperature, especially above 200 °C.     

Lubrication of Si3N4 and Al2O3 in water with and without addition of silane coupling agents in the range of 0.05–0.10 mol/l

To improve water lubrication of ceramics at a lower sliding velocity, the effect of the addition of silane coupling agents was investigated. Si₃N₄ and Al₂O₃ were slid against themselves in water with and without the addition of silane coupling agents in amounts ranging from 0.05 to 0.10 mol/l. Silane coupling agents containing one or more amino groups were effective in reducing the friction of Si₃N₄ and Al₂O₃ in water. Si₃N₄ also showed significant wear reduction but not Al₂O₃. However, the addition of a silane coupling agent containing an epoxy group increased both friction and wear of Si₃N₄. Improved lubricative characteristics of Si₃N₄ in water and in silane coupling agent solutions were obtained when Si₃N₄ contained smaller amounts of sintering additives. The adsorption behaviour of a silane coupling agent on ceramics was examined using both Fourier transform infrared spectroscopy and thin layer chromatography to clarify the interaction between the silane coupling agent and the ceramics. The role of polysiloxane film formation on ceramics is discussed to demonstrate the lubrication properties of ceramics.     

High-temperature tribological properties of spark-plasma-sintered Al2O3 composites containing barite-type structure sulfates

Al₂O₃–50BaSO₄–20Ag, Al₂O₃–50BaSO₄–10SiO₂, Al₂O₃–50(mass%)SrSO₄, Al₂O₃–50PbSO₄–5SiO₂, Al₂O₃–50BaSO₄ and Al₂O₃–50BaCrO₄ composites (mass%) were prepared by spark plasma sintering and their microstructure and high-temperature tribological properties were evaluated. Al₂O₃–50BaSO₄–20Ag composites (mass%) showed the lowest friction coefficients at the temperature ranging from 473 to 1073 K. Thin Ag film was observed on the wear tracks of the composites above 473 K. In addition, the friction coefficients of Al₂O₃ composites containing SrSO₄ and PbSO₄ were as low as those of Al₂O₃–BaSO₄ and Al₂O₃–BaCrO₄ composites at the temperatures up to 1073 K. The thin films formed on the wear tracks of the Al₂O₃–SrSO₄ composites were composed of Al₂O₃ and SrSO₄ phases, while the films formed on the wear tracks of the Al₂O₃–PbSO₄–SiO₂ composites consisted of Al₂O₃, PbSO₄ and SiO₂ phases.     

Comparison on abrasive wear of SiCrFe, CrFeC and Al2O3 reinforced Al2024 MMCs

The effects of volume fraction and size of SiCrFe, CrFeC, and Al₂O₃ particulates on the abrasive wear rate of compo-casted Al2024 metal matrix composites (MMCs) were studied. The process variables like the stirring speed, position and the diameter of the stirrer have affected the diffusion between particulates and matrix.The abrasive wear rate was decreased by the increase in particulate volume fraction of SiCrFe and CrFeC intermetallic reinforced composites over 80 grade SiC abrasive paper. The wear rates of the all composites decreased with aging treatment, and the best result was seen for the composite having a hybrite structure as SiCrFe and CrFeC particulates together. Nevertheless, the fabrication of composites containing soft particles as copper favors a reduction in the friction coefficient.     

The effect of Al2O3 on the friction performance of automotive brake friction materials

This study consists of two stages. In the first stage, bronze-based break linings were produced and friction-wear properties of them were investigated. In the second stage, 0.5%, 1%, 2% and 4% alumina (Al₂O₃) powders were added to the bronze-based powders and Al₂O₃ reinforced bronze-based break linings were produced. Friction–wear properties of the Al₂O₃ reinforced samples were aslo investigated and compared to those of plain bronze-based ones. For this purpose, friction coefficient and wear behaviour of the samples were tested on the grey cast iron disc. The hardness and density of the samples were also determined. Microstructures of the samples before and after the sintering and the worn surfaces of the wear specimens were examined using a scanning electron microscope (SEM). The sample compacted at 350 MPa and sintered at 820 °C exhibited the optimum friction–wear behaviour. With increase in friction surface temperature, a reduction in the friction coefficient of the samples was observed. The lowest reduction in the friction coefficient with increasing temperature was for the 2% and 4% Al₂O₃ reinforced samples. The SEM images of the sample indicated that increase in Al₂O₃ content resulted in adhesive wear. With increase in Al₂O₃ content, a reduction in mass loss of the samples was also observed. Overall, the samples reinforced with 2% and 4% Al₂O₃ exhibited the best results.     

Tribological characteristics of low-pressure plasma-sprayed A12O3 coating from room temperature to 800 °C

The tribological characteristics of low-pressure plasma-sprayed (LPPS) Al₂O₃ coating sliding against alumina ball have been investigated from room temperature to 800 °C. These friction and wear data have been compared quantitatively with those of bulk sintered alumina to obtain a better understanding of wear mechanisms at elevated temperatures. The friction and wear of Al₂O₃ coating show a strong dependence on temperature, changing from a mild to a severe wear regime with the increase of temperature. The coefficient of friction at room temperature is approximately 0.17 to 0.42, depending on applied load. The tribochemical reaction between the coating surface and water vapor in the environment and the presence of the hydroxide film on the Al₂O₃ coating reduce the friction and wear at room temperature as contrasted to those of bulk sintered alumina. At intermediate temperatures, from 400 to 600 °C, the friction and wear behavior of Al₂O₃ coating depends on the inter-granular fracture and pull-out of Al₂O₃ grains. At above 700 °C, formation and deformation of fine grain layer, and abrasive wear in the form of removal of fine alumina grains further facilitate the friction and wear process of Al₂O₃ coating.     

Dry sliding wear mechanism for P/M austenitic stainless steels and their composites containing Al2O3 and Y2O3 particles

Austenitic stainless steels are used in applications demanding general corrosion resistance at room or moderate operating temperatures. However, their use is often limited by the relative softness of these materials and their suceptibility to wear and galling. The present investigation deals with the dry sliding wear behaviour of two P/M austenitic stainless steels (AISI 304L and 316L) and their composites containing two different ceramic particles (Al₂O₃ and Y₂O₃) and two different sintering activators (BN and B₂Cr). Unlubricated pin-on-disc wear tests were carried out. Wear mechanisms were analysed by means of scanning electron microscopy and X-ray diffraction. A plastic deformation and particle detachment wear mechanism was revealed. Plasticity during sliding induced an austenite to martensite transformation. The presence of ceramic particles (Al₂O₃ and Y₂O₃) and sintering activators (B₂Cr, BN) improved significantly the wear resistance (especially the combination Al₂O₃ and B₂Cr). Ceramic particles limited plastic deformation while sintering activators decreased final porosity.     

Improved wear resistance of Si3N4 tool inserts by addition of Al2O3 platelets

In the present work, Si₃N₄ matrix composites reinforced with different amounts of Al₂O₃ platelets (0, 30 and 50vol%) were produced with the aim of increasing the tribochemical resistance in the machining of steels. Tool wear was related to the linear increase of the main cutting force (F_c) with time (dF_c/dt); a real-time parameter that can be used to assess the cutting edge damage and to stop machining before the tool fails. For all machined steels, tool wear resistance increased with increasing Al₂O₃ platelet content.     

Tribological properties of ZrO2 (Y2O3)-Mo-BaF2/CaF2 composites at high temperatures

ZrO₂ (Y₂O₃) with different contents of BaF₂/CaF₂ and Mo were fabricated by hot pressed sintering, and the tribological behavior of the composites against SiC ceramic was investigated from room temperature to 1000 °C. It was found that the ZrO₂ (Y₂O₃)-5BaF₂/CaF₂-10Mo composite possessed excellent self-lubricating and anti-wear properties. The low friction and wear were attributed to enhanced matrix and BaMoO₄ formed on the worn surfaces.     

Tribological Properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/CuCrZr Composites

Al₂O₃ particles reinforced Cu–Cr–Zr alloy matrix composite was fabricated through a powder metallurgy plus hot extrusion process by using the water atomization Cu–Cr–Zr powder as raw material. The effect of aging treatment on the tribological behavior of the composite was investigated. Experimental results show that tiny coherent precipitated phases were formed in the matrix after proper aging treatment and therefore good combination properties could be obtained. The wear rates of the Al₂O₃/CuCrZr composite and its matrix alloy were obviously influenced by the aging treatment, wherein the best wear resistance was reached at the aging temperature corresponding to the highest Vickers hardness. The major reason was that the depth of plastic deformation in the subsurface region was dramatically decreased due to the improvement of mechanical properties of the matrix, and therefore adhesion induced surface materials loss could be markedly alleviated. By comparing with the SiC20 vol%/Cu composite, it is indicated that the Al₂O₃/CuCrZr composite exhibited much better wear resistance as well as higher electrical conductivity.     

Effects of anti-wear additives on friction and wear properties of Cr2O3 coating

The effects of some anti-wear additives on the friction and wear behaviour of plasma-sprayed Cr₂O₃ coating were investigated using a block-on-ring tester at ambient conditions. The results show that zinc dialkyldithiophosphate (ZDDP), tricesyl phosphate (TCP) and tributyl phosphate (TBP) significantly reduce the wear of Cr₂O₃ coating lubricated by paraffin oil. Additive concentrations as well as sliding time have great influence on the wear. The friction coefficient varies slightly with test conditions. The analysis by XPS of worn surfaces indicates that the wear resistance of these additives is due to the formation of tribochemical reaction films by reacting with Cr₂O₃ coatings.     

Tribological properties of spark-plasma-sintered ZrO2(Y2O3)-CaF2-Ag composites at elevated temperatures

Spark-plasma sintering is employed to synthesize self-lubricating ZrO₂(Y₂O₃) matrix composites with different additives of CaF₂ and Ag as solid lubricants by tailoring the composition and by adjusting the sintering temperature. The friction and wear behavior of ZrO₂(Y₂O₃) matrix composites have been investigated in dry sliding against an alumina ball from room temperature to 800 °C. The effective self-lubrication at different temperatures depends mainly on the content of various solid lubricants in the composites. The addition of 35 wt.% Ag and 30 wt.% CaF₂ in the ZrO₂(Y₂O₃) matrix can promote the formation of a well-covered lubricating film, and effectively reduce the friction and wear over the entire temperature range studied. The friction coefficients at low temperatures were at a minimum value for the composite containing 35 wt.% of silver. At this silver concentration, low and intermediate temperature lubricating properties are greatly improved without affecting high-temperature lubrication by the calcium fluoride in ZrO₂(Y₂O₃) matrix composites. The worn surfaces and transfer films formed during wear process have been characterized to identify the synergistic lubrication behavior of CaF₂ and Ag lubricants at different temperatures.     

Friction and wear behaviour of Thordon XL and LgSn80 in sliding against plasma-sprayed Cr2O3 coatings

This paper studies the friction and wear behaviour of two important bearing materials, Thordon XL and LgSn80, in dry and lubricated sliding vs. plasma-sprayed Cr₂O₃ coatings. As a reference, AISI 1043 steel is also studied under the same conditions. SEM, EDS and surface topography were employed to study the wear mechanisms. The results indicate that the Thordon XL/Cr₂O₃ coating pair gives the lowest dry friction coefficient (0.16) under a normal load of 45.3 N (pressure 0.453 MPa) at a velocity of 1 m/s. The dry friction coefficient of Thordon XL/Cr₂O₃ coating increases to 0.38 under a normal load of 88.5 N (pressure 0.885 MPa). The dry friction coefficients of the LgSn80/Cr₂O₃ coating are in the range of 0.31–0.46. Secondly, both dry wear rate under low normal load (45.3 N) and lubricated wear rate under a load of 680 N for Thordon XL are lower than those of LgSn80 in sliding against plasma-sprayed Cr₂O₃ coatings at a speed of 1 m/s. However, under a normal load of 88.5 N the dry wear rate of Thordon XL is much higher than that of LgSn80. Thirdly, a high viscosity lubricant (SAE 140) leads to lower wear for Thordon XL and LgSn80 than a low viscosity lubricant (SAE 30). Finally, the dominating wear mechanism for Thordon XL is shear fracture when against the plasma-sprayed Cr₂O₃ ceramic coating. For LgSn80 against plasma-sprayed Cr₂O₃ ceramic coating, abrasive wear is the governing failure mechanism.     

Tribological and corrosion behaviors of Al2O3/polymer nanocomposite coatings

In this paper, the tribological and electrochemical corrosion properties of Al₂O₃/polymer nanocomposite coatings were studied by using micro-hardness test, single-pass scratch test, abrasive wear test, and finally electrochemical technique such as potentiodynamic polarization measurement. The coatings containing Al₂O₃ nanoparticles showed improvement in scratch and abrasive resistance compared with that of polymer coating. The improvement in scratch and abrasive resistance is attributed to the dispersion hardening of Al₂O₃ nanoparticles in polymer coatings. Corrosion test results showed that the embedded Al₂O₃ nanoparticles in polymer matrix do not sacrifice the corrosion resistance of the polymer itself.     

The effect of the severity of the grinding mode on the wear characteristics of grade 36 Al2O3- and Al2O3-ZeO2-coated abrasive belts

With the trend toward increased production rates, demands on coated abrasive belts are becoming increasingly severe. A study was made of the wear and performance characteristics of two abrasive minerals used in two very different modes of grinding, a low pressure constant-load grinding test (to represent relatively mild grinding and finishing applications) and a high pressure constant-rate test (to represent severe machining applications). Al₂O₃ and Al₂O₃-ZrO₂ minerals in a resin-bonded cloth-backed construction generally used for most metal-working applications were studied.A variety of techniques were used to analyze and to define wear and grinding performance. These included the measurement of the caliper, energy consumption, mineral utilization and surface profiles of the belts, together with scanning electron microscopy (SEM) observations of belts at various stages of wear. Substantial differences were found in many areas, both for the two mineral types used in the same grinding mode and for the same mineral used in different grinding modes. Interesting data showing mineral consumption during the grinding process and SEM visual identification of key differences in coated abrasive wear are presented. The study indicates that, although a coated abrasive belt can function effectively over a wide range of applications, its wear characteristics will vary with the severity of the application.     

Wear properties of two-phase Al2O3/ZrO2 (Y2O3) ceramics at temperatures from 296 to 1073 K

Reciprocating sliding friction experiments were conducted with various two-phase, directionally solidified Al₂O₃/ZrO₂ (Y₂O₃) pins sliding on B₄C flats in air at temperatures of 296, 873, and 1073 K under dry sliding conditions. Results indicate that all the Al₂O₃/ZrO₂ (Y₂O₃) ceramics, from highly Al₂O₃-rich to ZrO₂-rich, exceed the main wear criterion requirement of 10⁻⁶ mm³ N⁻¹ m⁻¹ or lower for effective wear-resistant applications. Particularly, the eutectics and Al₂O₃-rich ceramics showed superior wear properties. The composition and microstructure of Al₂O₃/ZrO₂ (Y₂O₃) ceramics played a dominant role in controlling the wear and friction properties. The controlling mechanism of the ceramic wear, friction, and hardness was an intrinsic effect involving the resistance to shear fracture of heterophase bonding and cohesive bonding and the interlocking microstructures at different scales in the ceramics.     

火焰喷涂PA1010/n-SiO2复合涂层干摩擦磨损性能

利用火焰喷涂法制备PA1010/n-SiO2复合涂层,并采用均匀试验设计方法研究涂层在干摩擦条件下同GCr15 钢环配副时的摩擦学性能;利用SPSS 12.0统计软件对试验结果进行回归分析, 建立涂层摩擦系数和磨损质量损失同pv值 (摩擦载荷与摩擦速度的乘积)相关性的数学模型;利用示差扫描量热仪(Differential scanning calorimetry, DSC)和扫描电子显微镜(Scanning electron microscope, SEM)对复合涂层的热性能和磨损表面形貌进行分析。结果表明,n-SiO2的加入能明显提高涂层的结晶性能、耐磨性能。当n-SiO2含量为1.5%时,复合涂层摩擦磨损性能最佳,在试验条件下磨损质量损失降低近4倍,摩擦因数降低23％,跑合期缩短44％,复合涂层与GCr15钢环对磨时的磨损机理主要为疲劳磨损和轻微的粘附 磨损。