Improvement of Mechanical and Electrical Properties of Scandia-Doped Zirconia Ceramics by Post-Sintering with Hot Isostatic Pressing

Significant improvement in the fracture strength, accompanied by an enhancement in the electrical conductivity, of zirconia polycrystals that were doped with 3–7 mol% Sc₂O₃ was obtained by sintering at 1300°C for 1 h in air, followed by hot isostatic pressing (HIP) at 196 MPa at 1300° and 1450°C for 1.5 h in an argon-gas atmosphere. Dense bodies (with an average grain size of <0.5 μm) that were doped with 3.5 mol% of Sc₂O₃ showed the highest average fracture strength up to 1770 MPa and an electrical conductivity of 0.08 S/cm at 1000°C. The present zirconia ceramics, which consisted of submicrometer-sized grains of tetragonal phases and were stabilized with 5 and 6 mol% of Sc₂O₃, exhibited high strength (1330 and 1140 MPa, respectively) and good conductivity (0.15 and 0.18 S/cm, respectively); values for both properties were greater than those previously reported. The present HIPed zirconia ceramics, which have excellent properties, are candidates for an electrolyte of planar-type solid oxide fuel cells.     

Microstructure, Conductivity, and NO2 Sensing Characteristics of α-Al2O3-Doped (8 mol% Sc2O3)ZrO2 Composite Solid Electrolyte

α-Al₂O₃-doped (8 mol % Sc₂O₃)ZrO₂ composite solid electrolyte has been investigated in the fabrication of solid-state ceramic gas sensors. The microstructure and electrical conductivity of the composite solid electrolyte have been measured over a range of temperature from 240°C to 596°C. The composite solid electrolyte has been found to exhibit a higher conductivity compared with the commonly used (8 mol% Y₂O₃)ZrO₂ at temperatures above ∼448°C. The sensing characteristics for NO₂ detection have been studied in the temperature range of 500–650°C at the low concentration from 10 to 30 ppm and at high concentration from 100 to 500 ppm of NO₂. The NO₂ sensor was found to respond reproducibly and rapidly to the variations of NO₂, concentration, indicating that the composite solid electrolyte has promising application as a solid electrolyte for on-board exhaust gas monitoring.     

Structural Evolution and Electrical Properties of Sc2O3-Stabilized ZrO2 Aged at 850°C in Air and Wet-Forming Gas Ambients

X-ray diffraction (XRD) and electron microscopy investigations have been performed on Sc₂O₃-stabilized ZrO₂ as-sintered and after aging in air or in wet-forming gas at 850°C for 1000 h. Some tetragonal to monoclinic transformation had occurred in the near-surface regions of 4 mol% Sc₂O₃ samples after aging; the phase transition was more severe for samples aged in the forming gas ambient. A decrease of ∼20% in electrical conductivity accompanied the aging. In 6 mol% Sc₂O₃ samples, although no cubic to tetragonal transformation was detected, both the electrical conductivity and the activation energy for ionic conductivity decreased significantly during aging. Ten mole percent Sc₂O₃ samples did not show appreciable change in electrical conductivity due to aging, although some near-surface cubic to rhombohedral transformation did occur. Sharpening of the (400)_t XRD peak of Sc₂O₃-stabilzed tetragonal ZrO₂ accompanies the change(s) in the electrical conductivity.     

Refractory α-SiAlON Containing La2O3

Refractory Y-α-SiAlON with elongated grain morphology was obtained by utilizing La₂O₃ as a densification aid, which resulted in excellent room-temperature and high-temperature strength. Room-temperature strength of 1000 MPa was achieved when La₂O₃ was augmented by adding Y₂O₃ or removing AlN. With only La₂O₃, a temperature-independent strength of 800–950 MPa was maintained up to 1100°C, then gradually decreasing by 25% when reaching 1300°C. The R-curve measurements of fracture toughness showed relatively little dependence on microstructure, consistent with a strong interface that suppresses grain boundary decohesion. Compared with other densification aids such as SiO₂, Al₂O₃, Sc₂O₃, Y₂O₃, and Lu₂O₃, a finer microstructure was obtained by using La₂O₃. High nitrogen content in the residual La–Si–Al–O–N glass in equilibrium with the nitrogen-rich α-SiAlON is suggested to be the cause of these findings.     

High-Temperature Phase Relations in the Sc2O3-Ta2O5 System

The phase relations for the Sc₂O₃-Ta₂O₅ system in the composition range of 50-100 mol% Sc₂O₃ have been studied by using solid-state reactions at 1350°, 1500°, or 1700°C and by using thermal analyses up to the melting temperatures. The Sc_5.5Ta_1.5O₁₂ phase, defect-fluorite-type cubic phase (F-phase, space group Fm 3 m ), ScTaO₄, and Sc₂O₃ were found in the system. The Sc_5.5Ta_1.5O₁₂ phase formed in 78 mol% Sc₂O₃ at <1700°C and seemed to melt incongruently. The F-phase formed in ∼75 mol% Sc₂O₃ and decomposed to Sc_5.5Ta_1.5O₁₂ and ScTaO₄ at <1700°C. The F-phase melted congruently at 2344°± 2°C in 80 mol% Sc₂O₃. The eutectic point seemed to exist at ∼2300°C in 90 mol% Sc₂O₃. A phase diagram that includes the four above-described phases has been proposed, instead of the previous diagram in which those phases were not identified.     

Changes in Aging Behavior and Defect Structure of Yttria-Fully-Stabilized ZrO2 with Sc2O3 Doping

Methods of suppressing decreased conductivity in 8 mol% Y₂O₃-stabilized–92 mol% ZrO₂ (8YSZ) with aging were investigated. Different amounts of Sc₂O₃ were doped into 8YSZ. The electrochemical properties of Sc₂O₃-doped 8YSZ were measured, and the microstructural and local structural changes were characterized. The present results indicate that an appropriate amount of Sc₂O₃ doping, 3 or 4 mol%, effectively suppresses decreased conductivity with aging in 8YSZ.     

Mechanical Properties of CoAl Materials with the Combined Additions of ZrO2(3Y) and Al2O3

Intermetallic CoAl powder has been prepared via self-propagating high-temperature synthesis (SHS). Dense CoAl materials (99.6% of theoretical) with the combined additions of ZrO₂(3Y) and Al₂O₃ have been fabricated via spark plasma sintering (SPS) for 10 min at 1300°C and 30 MPa. The microstructures are such that tetragonal ZrO₂ (0.3 μm) and Al₂O₃ (0.5 μm) particles are located at the grain boundaries of the CoAl (8.5 μm) matrix. Improved mechanical properties are obtained; especially the fracture toughness and the bending strength of the materials with ZrO₂(3Y)/Al₂O₃= 16/4 mol% are 3.87 MPa·m^1/2 and 1080 MPa, respectively, and high strength (>600 MPa) can be retained up to 1000°C.     

Sol–Gel Processed Y-PSZ Ceramics with 5 wt% Al2O3

Y-PSZ ceramics with 5 wt% Al₂O₃ were synthesized by a sol–gel route. Experimental results show that powders of metastable tetragonal zirconia with 2.7 mol% Y₂O₃ and 5 wt% Al₂O₃ can be fabricated by decomposing the dry gel powder at 500°C. Materials sintered in an air atmosphere at 1500°C for 3 have high density (5.685 g/cm³), high content of metastable tetragonal zirconia (>96%), and high fracture toughness (8.67 MPa.m^1/2). Compared with the Y-PSZ ceramics, significant toughening was achieved by adding 5 wt% Al₂O₃.     

Fabrication of Transparent, Sintered Sc2O3 Ceramics

We report here the fabrication of transparent Sc₂O₃ ceramics via vacuum sintering. The starting Sc₂O₃ powders are pyrolyzed from a basic sulfate precursor (Sc(OH)_2.6(SO₄)_0.2·H₂O) precipitated from scandium sulfate solution with hexamethylenetetramine as the precipitant. Thermal decomposition behavior of the precursor is studied via differential thermal analysis/thermogravimetry, Fourier transform infrared spectroscopy, X-ray diffractometry, and elemental analysis. Sinterability of the Sc₂O₃ powders is studied via dilatometry. Microstructure evolution of the ceramic during sintering is investigated via field emission scanning electron microscopy. The best calcination temperature for the precursor is 1100°C, at which the resultant Sc₂O₃ powder is ultrafine (∼85 nm), well dispersed, and almost free from residual sulfur contamination. With this reactive powder, transparent Sc₂O₃ ceramics having an average grain size of ∼9 μm and showing a visible wavelength transmittance of ∼60–62% (∼76% of that of Sc₂O₃ single crystal) have been fabricated via vacuum sintering at a relatively low temperature of 1700°C for 4 h.     

Determination of Inversion Temperature of Sb2O3-Doped BaTiO3 Positive Temperature Coefficient of Resistivity (PTCR) Ceramics by the Finite Difference Method

The effect of the cooling rate on the PTCR (positive temperature coefficient of resistivity) characteristics of 0.1 mol% Sb₂O₃-doped BaTiO₃ ceramics has been investigated. Resistances both below and above the Curie temperature were increased by slow cooling, which indicated that the resistive layer width at the grain boundary increased as the cooling rate decreased. Concentration profiles of the Ba vacancies as a function of distance from the grain boundary have been simulated by the finite difference method. The inversion temperature of the 0.1 mol% Sb₂O₃-doped BaTiO₃ system was determined to be 1160°C from the measured electrical properties and computed concentration profiles.     

Transformation Plasticity and Toughening in CeO2-Partially-Stabilized Zirconia–Alumina (Ce-TZP/Al2O3) Composites Doped with MnO

Microstructure, phase stability, and mechanical properties of CeO₂-partially-stabilized zirconia (12 mol% Ce-TZP) containing 10 wt% Al₂O₃ and 1.5 wt% MnO were studied in relation to the base Ce-TZP and the Ce-TZP/Al₂O₃ composite without MnO. The MnO reacted with both CeO₂ and Al₂O₃ to form a new phase of approximate composition CeMnAl₁₁O₁₉. The reacted phase had a magnetoplumbite structure and formed elongated, needlelike crystals. The MnO-doped Ce-TZP/Al₂O₃ composites sintered at an optimum temperature of 1550°C exhibited high strength (650 MPa in four-point bending) and rising crack-growth-resistance behavior, with fracture toughness increasing from 7.6 to 10.3 MPa.In¹² in compact tension tests. These improved mechanical properties were associated with relatively high tetragonal-to-monoclinic transformation temperature ( M _s=−42°C) at small grain size (2.5 μm), significant transformation plasticity in mechanical tests (bending, uniaxial tension, and uniaxial compression) and transformation zones at crack tips in compact tension specimens. The transformation yield stress, zone size, and fracture toughness were sensitive to the sintering temperature varied in the range 1500° to 1600°C. Analysis of the transformation zones using Raman microprobe spectroscopy and calculation of zone shielding for the observed zones indicated that a large fraction of the fracture toughness (∼70%) was derived from transformation toughening.     

High-Temperature Strength and Fracture Toughness of Y2O3-Partially-Stabilized ZrO2/Al2O3 Composites

The temperature dependence of bending strength, fracture toughness, and Young's modulus of composite materials fabricated in the ZrO₂ (Y₂O₃)-Al₂O₃ system were examined. The addition of A1203 enhanced the high-temperature strength. Isostatically hot-pressed, 60 wt% ZrO₂ (2 mol% Y₂O₃)/40 wt% Al₂O₃ exhibited an extremely high strength, 1000 MPa, at 1000°C.     

Microstructure and Mechanical Properties of Hot-Pressed α-Al2O3-Seeded γ-Alumina Ceramics

High-quality alumina ceramics were fabricated by a hot pressing with MgO and SiO₂ as additives using α-Al₂O₃-seeded nanocrystalline γ-Al₂O₃ powders as the raw material. Densification behavior, microstructure evolution, and mechanical properties of alumina were investigated from 1250°C to 1450°C. The seeded γ-Al₂O₃ sintered to 98% relative density at 1300°C. Obvious grain growth was observed at 1400°C and plate-like grains formed at 1450°C. For the 1350°C hot-pressed alumina ceramics, the grain boundary regions were generally clean. Spinel and mullite formed in the triple-grain junction regions. The bending strength and fracture toughness were 565 MPa and 4.5 MPa·m^1/2, respectively. For the 1300°C sintered alumina ceramics, the corresponding values were 492 MPa and 4.9 MPa·m^1/2.     

Improvement in Mechanical Properties of Powder-Processed MoSi2 by the Addition of Sc2O3 and Y2O3

Additions of 1-20 mol% Sc₂O₃ or Y₂O₃ to MoSi₂ eliminate glassy SiO₂, which improves mechanical properties at both ambient and high temperatures. In particular, only 1 mol% ScO₃ additions dramatically enhance three-point bending strength from 521 to 1081 MPa. Vickers hardness, Young's modulus, fracture toughness, and high-temperature strength are also improved by this low level of additive. The improvement of mechanical properties is attributed to the formation of crystalline silicates: Sc₂Si₂O₇, Y₂Si₂O₇, Y₂SiO₅, and Y₄Si₃O₁₂, which are analyzed by XRD, SEM-EDS, and TEM-EDS methods.     

Influence of Processing Conditions on the Electrical Properties of CaCu3Ti4O12 Ceramics

The electrical properties of a series of CaCu₃Ti₄O₁₂ ceramics prepared by the mixed oxide route and sintered at 1115°C in air for 1–24 h to produce different ceramic microstructures have been studied by Impedance Spectroscopy. As-fired ceramics are electrically heterogeneous, consisting of semiconducting grains and insulating grain boundaries, and can be modelled to a first approximation on an equivalent circuit based on two parallel RC elements connected in series. The grain boundary resistance and capacitance values vary as a function of sintering time and correlate with the ceramic microstructure based on the brickwork layer model for electroceramics. The large range of apparent high permittivity values for CaCu₃Ti₄O₁₂ ceramics is therefore attributed to variations in ceramic microstructure. The grain-boundary resistance decreases by three to four orders of magnitude after heat treatment in N₂ at 800°–1000°C but can be recovered to the original value by heat treatment in O₂ at 1000°C. The bulk resistivity decreases from ∼80 to 30 Ω·cm with increasing sintering time but is independent of heat treatment in N₂ or O₂ at 800°–1000°C. The origin of the bulk semiconductivity is discussed and appears to be related to partial decomposition of CaCu₃Ti₄O₁₂ at the high sintering temperatures required to form dense ceramics, and not to oxygen loss.     

High-Temperature Strength of Liquid-Phase-Sintered SiC with AlN and Re2O3 (RE = Y, Yb)

Using AlN and RE₂O₃ (RE = Y, Yb) as sintering additives, two different SiC ceramics with high strength at 1500°C were fabricated by hot-pressing and subsequent annealing under pressure. The ceramics had a self-reinforced microstructure consisting of elongated α-SiC grains and a grain-boundary glassy phase. High-temperature strength up to 1600°C was measured and compared with that of the SiC ceramics fabricated with AlN and Er₂O₃. SiC ceramics with AlN and Y₂O₃ showed the best strength (∼630 MPa) at 1500°C, while SiC ceramics with AlN and Er₂O₃ the best strength (∼550 MPa) at 1600°C.     

Electrical Conduction in β-Bi2O3 Doped with Sb2O3

Electrical conduction in tetragonal β-Bi₂O₃ doped with Sb₂O₃ was investigated by measuring electrical conductivity, ionic transference number, and Seebeck coefficient. The β-Bi₂O₃ doped with 1 to 10 mol% Sb₂O₃ was stable up to 600°C and showed an oxygen ionic and electronic mixed conduction, where the electron conduction was predominant at low oxygen pressures. The oxygen-ion conductivity showed a maximum at 4 mol% Sb₂O₃, whereas the activation energy for the ionic conduction remained unchanged for 4 to 10 mol% Sb₂O₃-doped specimens. These results were interpreted in terms of the oxygen vacancy concentration and the distortion of the tetragonal structure. The electron conductivity and its oxygen pressure dependence decreased with increasing Sb₂O₃ content. The fact that Sb⁵⁺ is partially reduced by excess electrons in heavily doped β specimens at low oxygen pressures is explained.     

Subsolidus Phase Equilibria and Ordering in the System ZrO2-Y2O3

The subsolidus phase relations in the entire system ZrO₂-Y₂O₃ were established using DTA, expansion measurements, and room- and high-temperature X-ray diffraction. Three eutectoid reactions were found in the system: ( a ) tetragonal zirconia solid solution→monoclinic zirconia solid solution+cubic zirconia solid solution at 4.5 mol% Y₂O₃ and ∼490°C, ( b ) cubic zirconia solid solutiow→δ-phase Y₄Zr₃O₁₂+hexagonalphase Y₆ZrO₁₁ at 45 mol% Y₂O₃ and ∼1325°±25°C, and ( c ) yttria C -type solid solution→wcubic zirconia solid solution+ hexagonal phase Y₆ZrO₁₁ at ∼72 mol% Y₂O₃ and 1650°±50°C. Two ordered phases were also found in the system, one at 40 mol% Y₂O₃ with ideal formula Y₄Zr₃O₁₂, and another, a new hexagonal phase, at 75 mol% Y₂O₃ with formula Y₆ZrO₁₁. They decompose at 1375° and >1750°C into cubic zirconia solid solution and yttria C -type solid solution, respectively. The extent of the cubic zirconia and yttria C -type solid solution fields was also redetermined. By incorporating the known tetragonal-cubic zirconia transition temperature and the liquidus temperatures in the system, a new tentative phase diagram is given for the system ZrO₂-Y₂O₃.     

Fracture Strength–Fracture Resistance Response and Damage Resistance of Sintered Al2O3–ZrO2 (12 mol% CeO2) Composites

The fracture strengths of sintered Al₂O₃ containing 20 and 40 vol% ZrO₂(12 mol% CeO₂)—zirconia-toughened alumina (ZTA)—composites along with the fracture resistance can be increased (e.g., to ∼900 MPa and >12 Mpa·m^1/2, respectively), by increasing the mean grain size of the t -ZrO₂ (and the Al₂O₃) from ∼0.5 μm to ∼3 μm. At these lower t -ZrO₂ contents, the fracture strength-fracture resistance curves show a continuous rise as opposed to the strength maxima observed in polycrystalline t -ZrO₂(12 mol% CeO₂), CeTZP, and ZrO₂(12 mol% CeO₂) ceramics containing ≤20 vol% Al₂O₃. The toughened composites also exhibit excellent damage resistance with fracture strengths of 500 MPa retained with surfaces containing ∼150- N Vickers indentations which produce cracks of ∼160-μm radius. Greater damage resistance correlates with an increase in the apparent R -curve response of these composites.     

The System Sc2O3-WO3

Phase relations in the system Sc₂O₃-WO₃ were characterized. Two stable binary compounds were, found. The 1:3 compound, SC₂(WO₄)₃, melts congruently at 1640°±10°C and forms a simple eutectic with WO₃ at ∼90 mol% WO₃ and 1309°+10°C. The 3 : 1 compound, Sc₆WO₁₂, forms a simple eutectic with the 1:3 compound at -69 mol% WO₂, and 1580°+10°C. The melting temperature of SC₆WO₁₂ was >1600°C.