Enhancement of the mechanical properties of poly(styrene-co-acrylonitrile) with poly(methyl methacrylate)-grafted multiwalled carbon nanotubes

Poly(methyl methacrylate) (PMMA) was grafted onto multiwalled carbon nanotubes (MWNTs). Composites of PMMA-grafted MWNTs and poly(styrene-co-acrylonitrile) (SAN) were prepared by solution casting from tetrahydrofuran. Since PMMA is miscible with SAN, the two polymers mix intimately to facilitate the dispersion of PMMA-grafted MWNTs in the SAN matrix. The intimate mixing is evidenced by the transparency of the composites. The incorporation of PMMA-grafted MWNTs to SAN (effective MWNT content=0.5-2 wt%) leads to increases in storage modulus at 40 °C, Young's modulus, tensile strength, ultimate strain, and toughness by 90, 51, 99, 184 and 614%, respectively. Such simultaneous increases in stiffness, strength, ductility and toughness of a polymer by rigid fillers are rarely observed.     

Effect of nanoTiO2 addition on poly(methyl methacrylate): An exciting nanocomposite

A systematic research has been conducted to investigate the matrix properties by introducing nanosize TiO₂ (5 nm, 2.0–30% by weight) filler into a poly (methyl methacrylate) (PMMA) resin. A twin screw extraction process was developed to disperse the particles into the PMMA. The thermal, mechanical, and viscoelastic properties of the virgin PMMA and nanoTiO₂‐PMMA composite were measured. The nanofiller infusion improves the thermal, mechanical and viscoelastic properties of the PMMA. Nanocomposite shows increase in storage modulus (～ 60%), rubbery modulus (～ 210%), glass transition temperature (～ 27%), crosslink density (～ 213%), initial decomposition temperature (～ 83% at 1% wt. loss), and activation energy (～ 141%). Mechanical performance and thermal stability of the nanoTiO₂‐PMMA composites are depending on the dispersion state of the TiO₂ in the PMMA matrix. Scanning electron microscopic study shows that the particles are well dispersed in the PMMA matrix. They are correlated with loading. Kinetics for thermal degradation analysis was studies. The integral procedural decomposition temperature (IPDT) is enhanced (～ 117%). The nanocomposites of high activation energy possess high thermal stability. Interrelation of T_g, crosslink density, IPDT, storage modulus, activation energy, and TiO₂ weight percent are established. Various reasons for these effects in terms of reinforcing mechanisms have been discussed. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Physical properties and crystallization behavior of poly(lactide)/poly(methyl methacrylate)/silica composites

Poly(lactide)/poly(methyl methacrylate)/silica (PLA/PMMA/SiO₂) composites were fabricated using a twin‐screw extruder. Nanosilica particles were incorporated to improve the toughness of the brittle PLA, and a chain extender reagent (Joncryl ADR 4368S) was used to reduce the hydrolysis of the PLA during fabrication. Highly transparent PLA and PMMA were designated to blend to obtain the miscible and transparent blends. To estimate the performance of the PLA/PMMA/SiO₂ composites, a series of measurements was conducted, including tensile and Izod impact tests, light transmission and haze measurements, thermomechanical analysis, and isothermal crystallization behavior determination. A chain extender increases the ultimate tensile strength of the PLA/PMMA/SiO₂ composites by ～43%, and both a chain extender and nanosilica particles increase Young's modulus and Izod impact strength of the composites. Including 0.5 wt % nanosilica particles increase the elongation at break and Izod impact strength by ～287 and 163%, respectively, compared with those of the neat PLA. On account of the mechanical performances, the optimal blending ratio may be between PLA/PMMA/SiO₂ (90/10) and PLA/PMMA/SiO₂ (80/20). The total light transmittance of the PLA/PMMA/SiO₂ composites reaches as high as 91%, indicating a high miscible PLA/PMMA blend. The haze value of the PLA/PMMA/SiO₂ composites is less than 35%. Incorporating nanosilica particles can increase the crystallization sites and crystallinities of the PLA/PMMA/SiO₂ composites with a simultaneous decrease of the spherulite dimension. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42378.     

Pultruded fiber-reinforced poly(methyl methacrylate) composites. II. Static and dynamic mechanical properties,environmental effect,and postformability

This paper presents a novel process developed to manufacture poly(methyl methacrylate) (PMMA) pultruded composite. The mechanical, thermal, and dynamic mechanical properties, environmental effect, postformability of various fiber (glass, carbon, and Kevlar 49 aramid fiber) reinforced pultruded PMMA composites have been studied. Results show mechanical properties (i.e., tensile strength, specific tensile strength, tensile modulus, and specific flexural strength) and thermal properties (HDT) increase with fiber content. Kevlar fiber/PMMA composites possess the highest specific tensile strength and HDT, carbon fiber/PMMA composites show the highest tensile strength and tensile modulus, and glass fiber/PMMA composites show the highest specific flexural strength. Pultruded glass-fiber-reinforced PMMA composites exhibit good weather resistance. These composite materials can be postformed by thermoforming under pressure, and mechanical properties of postformed products can be improved. The dynamic shear storage and loss modulus (G′, G″) of pultruded glass-fiber-reinforced PMMA composites increased with decreasing pulling rate, and their shear storage moduli are higher than those of pultruded Nylon 6 and polyester composites.     

Pultruded fiber reinforced thermoplastic poly(methyl methacrylate) composites. Part II: Mechanical and thermal properties

A novel process has been developed to manufacture poly(methyl methacrylate) (PMMA) pultruded parts. The mechanical and dynamic mechanical properties, environmental effects, postformability of pultruded composites and properties of various fiber (glass, carbon and Kevlar 49 aramid fiber) reinforced PMMA composites have been studied. Results show that the mechanical and thermal properties (i.e. tensile strength, flexural strength and modulus, impact strength and HDT) increase with fiber content. Kevlar fiber/PMMA composites possess the highest impact strength and HDT, while carbon fiber/PMMA composites show the highest tensile strength, tensile and flexural modulus, and glass fiber/PMMA composites show the highest flexural strength. Experimental tensile strengths of all composites except carbon fiber/PMMA composites follow the rule of mixtures. The deviation of carbon fiber/PMMA composite is due to the fiber breakage during processing. Pultruded glass fiber reinforced PMMA composites exhibit good weather resistance. They can be postformed by thermoforming, and mechanical properties can be improved by postforming. The dynamic shear storage modulus (G′) of pultruded glass fiber reinforced PMMA composites increased with decreasing pulling rate, and G′ was higher than that of pultruded Nylon 6 and polyester composites.     

3D printing of copper particles and poly(methyl methacrylate) beads containing poly(lactic acid) composites for enhancing thermomechanical properties

Poly(lactic acid) (PLA) composite filaments with different copper (Cu) contents as high as 40 and 20 wt% of poly(methyl methacrylate) (PMMA) beads have been fabricated by twin-screw extruder for 3D printing. A fused-deposition modeling (FDM) 3D printing technology has been used to print the PLA composites containing hybrid fillers of Cu particles and PMMA beads. The morphology, mechanical, and thermal properties of the printed PLA composites were investigated. The tensile strength was slightly decreased, but storage modulus and thermal conductivity of PLA composites were significantly improved by adding Cu particles in the presence of PMMA beads. The PLA composites with hybrid fillers of 40 wt% of Cu particles and 20 wt% of PMMA beads resulted in thermal conductivity of 0.49 W m⁻¹ K⁻¹ which was three times higher than that of the bare PLA resin. The facilitation of the segregated network of high-thermally conductive Cu particles with the PMMA beads in PLA matrix provided thermally conductive pathways and resulted in a remarkable enhancement in thermal conductivity.     

Rheological behavior of blends of poly(methyl methacrylate) (PMMA) and poly(acrylonitrile-stat-styrene)-graft-polybutadiene (ABS)

The rheological behavior of blends of poly(methyl methacrylate) (PMMA) and poly(acrylonitrile-stat-styrene)-graft-polybutadiene (ABS) was investigated using a cone-and-plate rheometer. The rheological properties measured were shear stress (σ₁₂), viscosity (η), and first normal stress difference (N₁) as functions of shear rate (\documentclass{article}\pagestyle{empty}\begin{document}$ \dot \gamma$ \end{document}) in steady shearing flow, and storage modulus (G′) and loss modulus (G″) as functions of frequency (ω) in oscillatory shearing flow. It has been found that the rheological behavior of blends of ABS and PMMA was very similar to that of blends of poly(styrene-stat-acrylonitrile) (SAN) and PMMA, in that N₁ in logarithmic plots of N₁ versus σ₁₂, and G′ in logarithmic plots of G′ versus G″, vary regularly with blend composition. This has led us to conclude that the rubber particles that are grafted on an SAN resinous matrix in ABS resin plays only a minor role in influencing the compatibility of ABS/PMMA blends, and that the SAN chains attached to the surface of rubber particles, and the SAN matrix phase, play a major role in compatibilizing ABS resin with PMMA.     

Nonisothermal crystallization kinetics and thermomechanical properties of multiwalled carbon nanotube‐reinforced poly(ε‐caprolactone) composites

BACKGROUND: The technological development of poly(ε‐caprolactone) (PCL) is limited by its short useful lifespan, low modulus and high crystallinity. There are a few papers dealing with the crystallization behavior of carbon nanotube‐reinforced PCL composites. However, little work has been done on the crystallization kinetics of melt‐compounded PCL/multiwalled carbon nanotube (MWNT) nanocomposites. In this study, PCL/MWNT nanocomposites were successfully prepared by a simple melt‐compounding method, and their morphology and mechanical properties as well as their crystallization kinetics were studied. RESULTS: The MWNTs were observed to be homogeneously dispersed throughout the PCL matrix. The incorporation of a very small quantity of MWNTs significantly improved the storage modulus and loss modulus of the PCL/MWNT nanocomposites. The nonisothermal crystallization behavior of the PCL/MWNT nanocomposites exhibits strong dependencies of the degree of crystallinity (X_c), peak crystallization temperature (T_p), half‐time of crystallization (t_1/2) and Avrami exponent (n) on the MWNT content and cooling rate. The MWNTs in the PCL/MWNT nanocomposites exhibit a higher nucleation activity. The crystallization activation energy (E_a) calculated with the Kissinger model is higher when a small amount of MWNTs is added, then gradually decreases; all the E_a values are higher than that of pure PCL. CONCLUSION: This paper reports for the first time the preparation of high‐performance biopolymer PCL/MWNT nanocomposites prepared by a simple melt‐compounding method. The results show that the PCL/MWNT nanocomposites can broaden the applications of PCL. Copyright © 2008 Society of Chemical Industry     

Effect of multiwalled carbon nanotubes on crystallization behavior of poly(vinylidene fluoride) in different solvents

In this study, the poly(vinylidene fluoride) (PVDF)—multiwalled carbon nanotubes (MWNTs) composites have been prepared by solution casting in two different solvents: dimethyl sulfoxide (DMSO) and dimethylacetamide (DMAc). Fourier transform infrared spectroscopy (FTIR) and differential scanning calorimeter (DSC) results showed that the crystal phases of PVDF are quite different in the two solvents. When DMSO is used as the solvent, the PVDF crystalline phases could be greatly alternated from α‐form to β‐form by the incorporation of MWNTs. While the crystalline structure of PVDF hardly change in the case of DMAc. The DSC and polarized optical microphotographs implied that MWNTs not only act as nucleating agents for PVDF but also confine the crystallization of PVDF. Besides, it was found that the storage modulus (E′) of the composites were significantly enhanced with an appropriate content of MWNTs. And when using DMSO as the solvent, one relaxation process emerges in the loss tan δ (loss factor) curves of the neat PVDF and PVDF/MWNTs composites, while it was not observed in the DMAc system. The obtained results revealed that varing solvents have different effects on the crystallization behavior of PVDF with the addition of MWNTs. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of multi‐walled carbon nanotubes on crystallization,thermal, and mechanical properties of poly(vinylidene fluoride)

Composites were prepared by solution blending poly(vinylidene fluoride) (PVDF) and multi‐walled carbon nanotubes (MWNTs). Fourier transform infrared spectroscopy (FTIR) and X‐ray diffraction (XRD) results showed that the crystalline structure of PVDF was changed by the addition of MWNTs and a MWNTs‐induced crystal transformation from α‐phase to β‐phase of PVDF was confirmed. With differential scanning calorimeter (DSC) and dynamic mechanic thermal analysis (DMA) techniques, thermal and mechanical properties of the composite films were examined. As the DSC results showed, addition of MWNTs would lead to the increased cooling crystallization temperature (T_c), implying that MWNTs nanoparticles could act as nucleating agents, which is further proved with the help of polarized optical microphotographs. On the other hand, the decreasing of D_d (degree of crystallinity) implied that the MWNTs networks can confine the crystallization of PVDF. Through the curve analysis of the dynamic mechanical measurements, it was found that the storage modulus (E′) is significantly enhanced, revealing that a strong interaction should exist between PVDF and MWNTs. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Property improvement of plasticized poly(vinyl chloride) by nano‐TiO2 and poly(methyl methacrylate)–encapsulated nano‐TiO2

To improve the physical properties of plasticized poly(vinyl chloride) (p‐PVC), the p‐PVC nanocomposites filled with four loading levels (3, 5, 7, and 9 parts per hundred of PVC resin) of either nanosized titanium dioxide (nTiO₂) or poly(methyl methacrylate)–encapsulated nTiO₂ (PMMA‐nTiO₂) were prepared by melt mixing on a two‐roll mill, followed by compression molding. The PMMA‐nTiO₂ used in this study was synthesized via in situ differential microemulsion polymerization. The resulting PMMA‐nTiO₂ exhibited core‐shell morphology (nTiO₂ core and PMMA shell) with an average diameter of 42.6 nm. The effects of nTiO₂ and PMMA‐nTiO₂ on the tensile properties, hardness, morphology, and thermal stability of the as‐prepared p‐PVC nanocomposites were then investigated and compared. The inclusion of either nTiO₂ or PMMA‐nTiO₂ nanoparticles increased the tensile strength, Young's modulus, hardness, and thermal stability of the nanocomposites in a dose‐dependent manner and reduced the elongation at break. However, the elongation at break was still higher than that for the neat p‐PVC. Moreover, the PMMA‐nTiO₂ nanocomposites had a higher enhancement of the tensile strength, Young's modulus, hardness, and thermal stability than the nTiO₂ nanocomposites at a similar loading level. Hence, the PMMA grafted on the nTiO₂ surface played an important role in toughening and increasing the thermal stability of the nanocomposites owing to the improved miscibility and interfacial adhesion between the encapsulated nanofiller and PVC matrix. J. VINYL ADDIT. TECHNOL., 22:433–440, 2016. © 2015 Society of Plastics Engineers     

Nucleation effect of hydroxyl‐purified multiwalled carbon nanotubes in poly(p‐phenylene sulfide) composites

To investigate the nucleation effect of hydroxyl‐purified multiwalled carbon nanotubes (MWNTs‐OH) in poly(p‐phenylenesulfide) (PPS), a series of composites were prepared by blending PPS with MWNTs‐OH at 1, 2, and 3 wt %, respectively. Under SEM observation MWNTs‐OH were found homogeneously dispersed in the PPS matrix. DSC thermograms revealed that the enthalpy (ΔH_c) of the composites increased with increasing MWNT‐OH content, whereas the crystallization temperature (T_c) decreased progressively. The decrease in T_c was in accordance with the smaller crystallite size determined with WXRD characterization, and the increase in ΔH_c was evidenced by FTIR and XPS analyses. The higher ΔH_c shows that MWNTs‐OH serves as a nucleating agent, providing sufficiently multiplied sites for crystal growth. The lowering of T_c was attributed not only to MWNTs‐OH network hindrance to PPS chain fusing rearrangement, but also to a poorer affinity between MWNTs‐OH and PPS; both effects coordinately govern T_c of PPS/MWNTs‐OH composites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Viscoelastic properties of blends of poly(methyl methacrylate) and poly(styrene‐co‐acrylonitrile) having various acrylonitrile contents

Dynamic viscoelastic properties of blends of poly(methyl methacrylate) (PMMA) and poly(styrene‐co‐acrylonitrile) (SAN) with various AN contents were measured to evaluate the influence of SAN composition, consequently χ parameter, upon the melt rheology. PMMA/SAN blends were miscible and exhibited a terminal flow region characterized by Newtonian flow, when the acrylonitrile (AN) content of SAN ranges from 10 to 27 wt %. Whereas, PMMA/SAN blends were immiscible and exhibited a long time relaxation, when the AN content in SAN is less than several wt % or greater than 30 wt %. Correspondingly, melt rheology of the blends was characterized by the plots of storage modulus G′ against loss modulus G″. Log G′ versus log G″ plots exhibited a straight line of slope 2 for the miscible blends, but did not show a straight line for the immiscible blends because of their long time relaxation mechanism. The plateau modulus, determined as the storage modulus G′ in the plateau zone at the frequency where tan δ is at maximum, varied linearly with the AN content of SAN irrespective of blend miscibility. This result indicates that the additivity rule holds well for the entanglement molecular weights in miscible PMMA/SAN blends. However, the entanglement molecular weights in immiscible blends should have “apparent” values, because the above method to determine the plateau modulus is not applicable for the immiscible blends. Effect of χ parameter on the plateau modulus of the miscible blends could not be found. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Rheology and properties of melt-processed poly(ether ether ketone)/multi-wall carbon nanotube composites

Poly(ether ether ketone) (PEEK)/multi-wall carbon nanotube (MWNT) composites containing up to 17 wt% filler were prepared using a twin screw extruder. Transmission electron microscopy (TEM) images reveal that the MWNTs were homogeneously dispersed in the PEEK matrix. Linear viscoelastic measurements show that both complex viscosity and moduli increase with increasing MWNT concentration. The storage modulus, G^′ exhibits a dramatic seven order increase in magnitude around 1 wt%, leading to a solid-like low-frequency behaviour at higher loadings; the effect can be attributed to network formation at a rheological percolation threshold. Rheotens measurements show that the melt strength also increases significantly on addition of nanotubes, however, the drawability decreases. An analytical Wagner model was used to calculate the apparent elongational viscosity over a wide range of elongational rates, and to reveal significant increases on addition of MWNTs, with a similar threshold behaviour. The electrical response is also dominated by percolation effects, increasing by nearly 10 orders of magnitude from 10⁻¹¹ to 10⁻¹ S/cm, on the addition of only 2 wt% MWNTs. In contrast, the thermal conductivity and tensile elastic modulus of the composites increased linearly with nanotube content, rising by 130% and 50%, at 17 wt% MWNTs, respectively.     

Mechanical properties of drawn poly(methyl methacrylate) filled with ultrafine particles

The elastic and yield properties of drawn poly(methyl methacrylate) (PMMA) filled with ultrafine SiO₂ are described as functions of filler content and size. The drawn PMMA composites were made by uniaxially drawing to x4.0 at 100°C and at a rate of 20 mm/min. Four compliance values, i.e., S₃₃, S₁₁, S₁₃, and S₄₄ were determined. These values decreased with filler content and decreasing filler size. The relative compliance values S^de/S^do(S^de is the compliance of drawn PMMA composites and S^do is that of drawn unfilled PMMA) are almost equivalently changed with changes in filler content. The elastic properties of drawn PMMA composites are thus reinforced isotopically. This is characteristic of PMMA which has a large side group. The yield behavior of drawn PMMA composites have similar filler size and content dependence to those of elastic properties except that the transverse yield stresses become more brittle with filler content. The anisotropy in yield stress is relatively larger than that of elastic properties. This is probably because the anti-reiforcing effect, such as fibrillation becomes prominent with increasing filler content in the perpendicular direction.     

Compatibilization of poly(methyl methacrylate) and cellulose nanocrystals through co-continuous phase to enhance the thermomechanical properties

The present study focuses on enhancing the thermomechanical properties of poly(methyl methacrylate) (PMMA), a transparent and biocompatible polymer known for its high strength but limited toughness. The approach involves the development of PMMA/cellulose nanocrystals (CNCs) composites. To improve the interfacial compatibility between PMMA and CNCs, a two-step process is employed. Initially, the CNCs undergo oxidation using sodium periodate, followed by the introduction of amino groups through reductive amination. The aminated CNCs are then covalently bonded to PMMA via an amidation reaction using the “grafting onto” approach. Subsequently, the grafted CNCs are incorporated into the PMMA matrix using the solvent casting method. The resulting composites are extruded into filaments. Elemental composition analysis confirms CNC modification, revealing the presence of 1.6% nitrogen. The modified CNCs exhibit a higher degradation temperature than unmodified CNCs, showing a 50°C increase. The composites' dynamic mechanical analysis (DMA) reveals a 20% improvement in storage modulus (E′) upon incorporating 1.5% of the grafted CNCs into the PMMA matrix. This enhancement is attributed to the formation of co-continuous phases in the composite structure.     

An experimental and theoretical investigation of the compressive properties of multi-walled carbon nanotube/poly(methyl methacrylate) nanocomposite foams

Polymer nanocomposite foams are promising low density substitutes for nanocomposites. Carbon nanotube/polymer nanocomposite foams possess high strength, low density, and can be made conductive. Good control of foam properties is of great importance in the application of such materials. In the current study, multi-walled carbon nanotubes (MWNTs) with controlled aspect ratio were used to alter the foam morphology in MWNT/poly(methyl methacrylate) (PMMA) nanocomposite foams produced by a supercritical carbon dioxide (CO₂) foaming process. It was found that with the addition of one weight percent of MWNTs, the Young’s modulus of polymer foams increased by as much as 82%, and the collapse strength increased by as much as 104%. The influence of MWNT aspect ratio on the compressive properties of nanocomposite foams was investigated. The addition of MWNTs influenced the foam properties in two ways: improving the compressive properties of the solid matrix, and reducing the bubble size of the nanocomposite foams. A modified constitutive model for predicting the compressive properties of high density closed-cell polymer foams was developed. The influence of the bubble size on the mechanical properties of polymer foams was discussed based on the new model.     

Three-stage interaction of dimethyl phthalate,dibutyl phthalate,and poly(vinyl acetate) with poly(methyl methacrylate)

The interaction of dimethyl phthalate (DMP), n-dibutyl phthalate (DBP), and poly(vinyl acetate) (PVAc) with poly(methyl methacrylate) (PMMA) was studied. Changes in the tensile strength, elastic modulus, and percentage elongation at break of the PMMA-additive films produced were followed using the Instron testing machine. The three additives produced (1) an initial plasticization, with a decrease in tensile strength and modulus and a possible increase in elongation; (2) an antiplasticization, with accompanying increase in tensile strength and modulus and an anomalous increase in elongation; and (3) a final plasticization, with a marked decrease in tensile strength and modulus and a definite increase in elongation of PMMA. The three effects were influenced by the molecular weight of the PMMA. A spacer effect by the interposition of the molecules of the additives between those of PMMA is proposed for the initial plasticization, while for the final plasticization, a lubrication action of the plasticizers on PMMA is suggested. Antiplasticization is explained by the formation of secondary bonds between the antiplasticizer and the PMMA molecules.     

Multiwalled carbon nantoubes‐reinforced poly(hydroxyaminoether) prepared by one pot graft‐from method

Multiwalled carbon nanotubes (MWNTs)‐reinforced poly(hydroxyaminoether) (PHAE) was fabricated via one pot graft‐from method. The modification of MWNTs and in situ polymerization of PHAE were combined in one reaction pot without interruption for the purification of modified carbon nanotubes. Fourier transform infrared, scanning electron microscopy, transmission electron microscopy, and Raman spectra clearly indicated that PHAE was successfully attached to the surface of MWNTs via esterification reaction between epoxy and carboxylic acid from MWNTs. Tensile tests showed that the tensile strength and modulus of PHAE/MWNTs composites were improved compared with that of pristine PHAE. Moreover, the reinforcing effect of one pot graft‐from method was found to be better than that of graft‐to method. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

多壁碳纳米管对聚胺醚电纺溶液流变性能的影响

通过原位聚合法将酸处理过的多壁碳纳米管(MWNTs)与聚胺醚复合,制备碳管含量不同的电纺溶液。采用应变控制型流变仪研究MWNTs/聚胺醚电纺溶液的流变行为。静态流变结果表明:聚胺醚为切力变稀的非牛顿流体,体系的表观粘度随着碳管含量的增加而增大,非牛顿指数减小;随着碳管含量的增加,聚胺醚电纺溶液的粘流活化能增加。动态流变结果表明:储存模量G′和损耗模量G″均随着MWNTs含量的增加而增加。