Effects of sputtering pressure and thickness on properties of ZnO:Al films deposited on polymer substrates

Highly conducting and transparent aluminum doped zinc oxide (ZnO:Al) thin films have been deposited on polyimide substrate by r.f. magnetron sputtering at room temperature. The influence of sputter pressure and thickness on the structural, electrical, and optical properties of ZnO:Al films deposited on polyimide substrate is reported. The crystallinity and degree of orientation was increased by decreasing the sputter pressure. For higher sputtering pressures an increase on the resistivity was observed due to a decrease on the mobility and the carrier concentration. As the film thickness was increased, the crystallite sizes were increased, but the average transmittance in the wavelength range of the visible spectrum was decreased. The electrical performances of the ZnO:Al films deposited on glass substrates are slightly worse than the ones of the films deposited on polyimide substrates with same thickness. The lowest resistivity of 8.6?×?10^?4 Ω cm can be obtained for films deposited on glass substrate with the thickness of 800 nm.     

Effect of a hydrogen ratio in electrical and optical properties of hydrogenated Al-doped ZnO films

This study examined the effect of the hydrogen ratio on the electrical and optical properties of hydrogenated Al-doped zinc oxide (AZO) thin films deposited by rf magnetron sputtering using a ceramic target (98 wt% ZnO, 2 wt% Al₂O₃). Various AZO films on glass were prepared by changing the H₂/(Ar?+?H₂) ratio at room temperature. The AZO/H films showed a lower resistivity and a higher carrier concentration and mobility than the AZO films. However, the resistivity and mobility of the AZO/H films increased and decreased with increasing H₂ flow ratio, respectively. As a result, the AZO/H films grown with 2% H₂ addition showed excellent electrical properties with a resistivity of 4.98?×?10⁴ Ωcm. The UV-measurements showed that the optical transmission of the AZO/H films was >85% in the visible range with a wide optical band gap. In addition, the effect of H₂ flow ratio on the structure and composition of hydrogenated AZO thin films have also been studied.     

Growth characteristics and film properties of gallium doped zinc oxide prepared by atomic layer deposition

We carried out comprehensive studies on structural, optical, and electrical properties of gallium-doped zinc oxide (Ga:ZnO) films deposited by atomic layer deposition (ALD). The gallium(III) isopropoxide (GTIP) was used as a Ga precursor, which showed pure Ga₂O₃ thin film with high growth rate. Using this precursor, conductive Ga doped ZnO thin film can be successfully deposited. The electrical, structural and optical properties were systematically investigated as functions of the Ga doping contents and deposition temperature. The best carrier concentration and transmittance (7.2?×?10²⁰ cm^?3 and 83.5 %) with low resistivity (≈3.5?×?10^?3?Ωcm) were observed at 5 at.% Ga doping concentration deposited at 250 °C. Also, low correlation of deposition temperature with the carrier concentration and film structure was observed. This can be explained by the almost same atomic radius of Ga and Zn atom.     

Low‐resistive and transparent AZO films prepared by PLD in magnetic field

Al₂O₃‐doped ZnO (AZO) thin films have been deposited onto glass substrates using a split target consisting of AZO (1 wt%) and AZO (2 wt%) by pulsed laser deposition with an ArF excimer laser (λ = 193 nm, 15 mJ, 10 Hz, 0.75 J/cm²). By applying a magnetic field perpendicular to the plume, the lowest resistivity of 8.54 × 10^?5Ω·cm and an average transmittance exceeding 91% over the visible range were obtained at a target‐to‐substrate distance of 25 mm for approximately 279‐nm‐thick AZO film (1.8 wt%) grown at a substrate temperature of 230 °C in vacuum. From cross‐sectional TEM observations and the XRD spectrum, a reason why the low resistivity (54 × 10^?5Ω·cm) was reproducibly obtained was considered to be due to the fact that a disorder of crystal growth originating in the vicinity of the interface between the substrate and the film was suppressed by application of the magnetic field and the c‐axis orientation took preference, giving rise to the increase of mobility. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 151(2): 40–45, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20026     

Effect of discharge power density on the properties of Al and F co-doped ZnO thin films prepared at room temperature

ZnO transparent conducting thin films co-doped with aluminium and fluorine (AZO:F) were prepared on glass substrates by RF magnetron sputtering at room temperature. The effect of discharge power density on the microstructure, surface morphology, electrical and optical properties was investigated. From XRD analysis, it was revealed that the intensity of (002) favoured orientation of ZnO films increased with power density from 2.6 to 6.1?W/cm² and then turned to a randomly orientated structure as power density continuously increased to 7.8?W/cm². The film prepared at 6.1?W/cm² showed a better crystallization and microstructure with larger, pyramid-like grains that were approximately 180?nm long and 90?nm wide. As a result, the electrical resistivity of the AZO:F films had a minimum of 4.1?×?10^?4???cm. The improvement in the electrical resistivity of AZO:F films was due to the increase in carrier concentration from 8.8?×?10²⁰ to 1.38?×?10²¹?cm^?3 and the mobility from 5.8 to 11.8?cm² V^?1 s^?1. The increase in carrier concentration with power density was also found to affect the optical property of the films due to the Moss-Burstein shift.     

Effects of substrate temperature on electrical and optical properties ITO films deposited by r.f. magnetron sputtering

Indium tin oxide (ITO) films have been prepared by r.f. magnetron sputtering using powder target. X-ray diffraction analysis indicates that the deposited films were polycrystalline and retained a cubic bixbite structure. The ITO films deposited at low substrate temperature (T _s) exhibit a (411) preferred orientation but the films deposited at high T _s prefer a (111) orientation. The substrate temperature was found to significantly affect the electrical properties. As the T _s was increased, the conductivity of ITO films was improved due to thermally induced crystallization. The lowest resistivity (8.7?×?10^?4 Ω-cm) was obtained from ITO films deposited at 450 °C. However, optical properties of the films were somewhat deteriorated. The infrared (IR) reflectance of the film increases with increasing the substrate temperature.     

Electrical and optical studies of transparent conducting ZnO:Al thin films by magnetron dc sputtering

Transparent conducting aluminium-doped Zinc oxide (ZnO:Al) films have been deposited on glass substrates by magnetron dc sputtering using a ceramic target (ZnO with 2 wt% Al₂O₃). The dependence of the electrical and optical properties of these films on substrate temperature, sputtering pressure of Ar and location of substrates were investigated in detail. Target is perpendicular with substrate and we controlled the distance ‘x’ of target and substrate. Optimized films with resistivity of 3.7?×?10^?4 Ω cm, an average transmission in the visible range (300–800 nm) of greater than 85% and the reflectance in the infrared range being greater than 85% have been formed. Substrate temperature, distance ‘x’, and working pressure are optimized for lower resistivity and high concentration of carriers.     

Electrical, optical, and structural properties of ITO co-sputtered IZO films by dual target magnetron sputtering

We have investigated electrical, optical, and structural properties of indium tin oxide (ITO) co-sputtered indium zinc oxide (IZO) film prepared by a dual target direct current (DC) magnetron sputtering at room temperature in pure Ar ambient. It was shown that the resistivity and sheet resistance of ITO co-sputtered IZO films monotonically increased with increasing DC power of ITO target at constant DC power of IZO target. Synchrotron X-ray scattering and scanning electron microscope examination results show that addition of ITO in the IZO film lead to crystallization of IZTO film due to low transition temperature of the ITO from amorphous to crystalline. However, ITO co-sputtered IZO film (ITO/IZO power?=?100 W:100 W) exhibit higher work function than those of pure IZO and ITO film. It was found that the work function as well as the electrical, optical, and surface properties of the IZTO film could be controlled by varying the DC power of IZO and ITO targets, respectively.     

Effects of transition metal (Ni, Mn, Cu) doping on ferroelectric properties of Bi0.9Nd0.1FeO3 thin films prepared by chemical solution deposition method

Transition metal (Ni, Mn, Cu) doped Bi_0.9Nd_0.1FeO₃ thin films were prepared on Pt(111)/Ti/SiO₂/Si(100) substrates by using a chemical solution deposition method. Compared to pure BiFeO₃ (BFO) thin film, improved ferroelectric and leakage current properties were observed in the transition metal doped thin films. The values of remnant polarization (2P _r ) and coercive electric field (2E _c ) of the transition metal doped thin films were 59 μC/cm² and 690 kV/cm at 700 kV/cm for the Ni-doped Bi_0.9Nd_0.1FeO₃ thin film, 57 μC/cm² and 523 kV/cm at 670 kV/cm for the Mn-doped thin film, and 85 μC/cm² and 729 kV/cm at 700 kV/cm for the Cu-doped thin film, respectively. The 2P _r values observed in the transition metal doped thin films were much larger than that of the BFO thin film, 21 μC/cm² at 660 kV/cm. Also the 2E _c values of in the transition metal doped thin films were lower than that of the BFO thin film, 749 kV/cm at 660 kV/cm. The reduced leakage current density was observed in the transition metal doped thin films, which is approximately two orders of magnitude lower than the BFO thin film, 2.6?×?10^?3 A/cm² at 100 kV/cm.     

Physical properties of transparent conducting indium doped zinc oxide thin films deposited by pulsed DC magnetron sputtering

Transparent conducting In-doped (1at.%) zinc oxide (IZO) thin films are deposited on glass substrate by bipolar pulsed DC magnetron sputtering. We have investigated the effect of pulse frequency on the physical properties of the IZO films. A highly c-axis oriented IZO thin films were grown in perpendicular to the substrate. At optimal deposition conditions, IZO films with a smoothest surface roughness of ～3.6 nm, a low-resistivity of 5.8?×?10^?3 Ωcm, and a high mobility of 14 cm/Vs were achieved. The optical spectra showed a high transmittance of above 85% in the UV–visible region and exhibited the absorption edge of near 350 nm. In micro-Raman, we observed the three phonon modes of host ZnO, which are E ₂ ^low, E ₂ ^high, and A ₁ modes, and the three additional modes. The origin of three additional modes is attributed to the host lattice defect due to the effect of In dopant and increasing the pulse frequency.     

Reliability assessment of indium tin oxide thin films by accelerated degradation test

The thermal degradation behavior and reliability of indium tin oxide (ITO) thin films deposited on glass substrates using radio frequency (rf) magnetron sputtering were investigated over the temperature range of 200–250^∘C in air. Accelerated degradation test (ADT) was performed to assess the reliability of ITO films. The lifetime of ITO films under normal operating condition (150^∘C) can be predicted to be 1.148 × 10⁵ h via statistical analysis and modeling of data acquired from ADT. The lifetime of ITO films was also evaluated using finite element analysis (FEA) based on the assumption of oxygen diffusion mechanism.     

Ferroelectric ceramics and thin films for pyroelectric applications

Abstract

The extensive work carried out at Caswell in recent years on ferroelectric ceramics for pyroelectric applications is reviewed briefly. With the ultimate aim of fully CMOS compatible integrated thermal detectors and imagers, pure and lanthanum doped lead titanate thin films have been deposited using the emerging PVD technique of dual ion beam sputtering (DIBS). The DIBS process produces high quality orientated perovskite films. Films have been formed at 500–600°C onto sapphire, MgO and silicon substrates by sputtering from an adjustable composite PLZT ceramic/Ti and Pb metallic target. Some substrates were coated with platinum/titanium prior to deposition to allow longitudinal electrical measurements to be made on the films. On silicon, the platinum/titanium electrodes were found to blister during the PLZT thin film deposition process. Pure and 7% lanthanum doped lead titanate films have shown pyroelectric effects with coefficients in the range 0.5–4.0 × 10^?4 Cm^?2 K^?1 and a figure of merit of 2.6 × 10^?5 Pa^?0.5 These results are encouraging with respect to the goal of integrated pyroelectric IR detector arrays on silicon. Further improvements should be possible since the process and substrate/electrode preparation have not yet been fully optimised.     

Electrical and optical properties of microwave dielectric thin films prepared by pulsed laser deposition

Abstract

Bi₂(Zn_1/3Nb_2/3)₂O₇, BiZN, materials possess high dielectric constant and low loss factor in microwave frequency region. They have good potential for device application, especially in the form of thin films. However, the microwave dielectric properties of a thin film are very difficult to be accurately measured. Evaluation on the dielectric behavior of the films through the performance of the microstrip line devices made of these films involves metallic conduction and stray field losses. A novel measuring technique, which can directly evaluate the microwave dielectric properties of a thin film is thus urgently needed.

In this paper, BiZN thin films were grown on [100] MgO single crystal substrates using pulsed laser deposition process. The high-frequency dielectric properties of thus obtained thin films were determined using optical transmission spectroscopy (OTS). The [100] preferentially oriented films with pyrochlore structure can be obtained for the thin films deposited at 400–600°C substrate temperature under 0.1 mbar oxygen pressure. OTS measurements reveal that the index of refraction (n=1.95–2.35) and absorption coefficient (k=0.28x10^?4-2.25 × 10^?4 nm^?1) of the films vary insignificantly with the crystallinity of the BiZN films.     

Nonlinear optical properties and morphologies of vanadyl‐phthalocyanine thin films prepared on polyethylene‐terephthalate film

Vanadyl phthalocyanine (VOPc) crystal thin films were prepared on poly(ethylene terephthalate) (PET) film. The VOPc film prepared on PET substrate at 120 °C had Phase II. The third harmonic (TH) intensity of the VOPc film was measured by the marker fringe method. The third optical susceptibility (χ⁽³⁾) estimated from TH intensity is 3.5 × 10^?9 esu. The transition from Phase I to Phase II of the VOPc film was enhanced with corona charging. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 140(2): 36–43, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10022     

Effects of the Ga-doping concentration on the characteristics of Zn<Subscript>0.7</Subscript>Mg<Subscript>0.3</Subscript>O thin films deposited by metal-organic chemical vapor deposition using an ultrasonic nebulization

Ga-doped Zn_0.7-xMg_0.3O thin films were deposited on glass substrates at 350 °C by metal-organic chemical vapor deposition using an ultrasonic nebulization technique to transport the source precursors, and the effects of the Ga-doping concentration were investigated. The films with Ga-doping concentrations less than 5 mol% grew with [001] preferred orientation perpendicular to the substrate surface and were composed of large crystallites. At Ga content greater than 5 mol%, the films grew with random orientation and very small crystallite size. The charge carrier concentration in the films increased rapidly up to 4 mol% Ga and then decreased gradually with further increases in the Ga-content. The film resistivity decreased with increasing Ga-content up to 4 mol% due mainly to the increase in charge carrier concentration. Then, the resistivity increased gradually with increasing Ga-content due to the decrease in mobility. The lowest resistivity of the Ga-doped Zn_0.7-xMg_0.3O thin film was 3.8?×?10^?1 Ωcm at the Ga doping concentration of 4 mol%. The mean transmittance in the visible range was more than 85% in all films. The optical band gap of the films increased with increasing Ga-doping concentration up to 5 mol% due to the Burstein-Moss effect.     

Photoluminescence and optical dispersion parameters of N-doped ZnO nano-fiber thin films

N-doped ZnO (NZO) nanocrystalline thin films were successfully synthesized via sol–gel method. The structural and optical properties of the films were characterized by various techniques including X-ray diffraction, atomic force microscopy (AFM), UV–vis absorption and photoluminescence. The UV–vis absorption edge was changed with increasing N-doping concentration. X-ray diffraction (XRD) results clearly showed that the zinc oxide doped with nitrogen (5 to 20 wt.%) were identified with phases of hexagonal ZnO and N-doped ZnO nanocrystalline thin films. The refractive index dispersion mechanism obeys the Single oscillator model. The dispersion parameters E _o and E _d of the thin films were determined. The dispersion parameters were changed by N dopant. It is evaluated that the structural, optical constants, photoluminescence properties of Zinc oxide film can be controlled by N dopants.     

Electrical and optical properties of fluorine-doped tin oxide (SnOx:F) thin films deposited on PET by using ECR–MOCVD

The electrical, optical, structural and chemical bonding properties of fluorine-doped tin oxide (SnO_x:F) films deposited on a plastic substrate prepared by Electron Cyclotron Resonance–Metal Organic Chemical Vapor Deposition (ECR–MOCVD) were investigated with special attention to the process parameters such as the H₂/TMT mole ratio, deposition time and amount of fluorine-doping. The four point probe method, UV visible spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic emission spectroscopy (AES), X-Ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) were employed to characterize the films. Based on our experimental results, the characteristics of the SnO_x:F thin films were significantly affected by the process parameters mentioned above. The amount of fluorine doping was found to be one of the major parameters affecting the surface resistivity, however its excess doping into SnO₂ lead to a sharp increase in the surface resistivity. The average transmittance decreased with increasing film thickness. The lowest electrical resistivity of 5.0?×?10^?3 Ω^.cm and highest optical transmittance of 90% in the visible wavelength range from 380 to700 nm were observed at an H₂/TMT mole ratio of 1.25, fluorine-doping amount of 1.3 wt.%, and deposition time of 30 min. From the XRD analysis, we found that the SnO_x:F films were oriented along the (2 1 1) plane with a tetragonal and polycrystalline structure having the lattice constants, a?=?0.4749 and c?=?0.3198 nm.     

Characterization of the CeO2 thin films for insulation layer and Pt/SrBi2Ta2O9/CeO2/Si MFISFET structure

Abstract

CeO₂ and SrBi₂Ta₂O₉ (SBT) thin films for MFISFET (metal-fcrroelectrics-insulator-semiconductor field effect transistor) were deposited by rf sputtering and pulsed laser deposition method, respectively. The effects of oxygen partial pressure during deposition for CeO₂ films were investigated. The oxygen partial pressure significantly affected the preferred orientation, grain size and electrical properties of CeO₂ films. The CeO₂ thin films with a (200) preferred orientation were deposited on Si(100) substrates at 600°C. The films deposited under the oxygen partial pressure of 50 % showed the best C-V characteristics among those under various conditions. The leakage current density of films showed order of the 10^?7～10^?8 A/cm² at 100 kV/cm. The SBT thin films on CeO₂/Si substrate showed dense microstructure of polycrystalline phase. From the C-V characteristics of MFIS structure composed of the SBT film annealed at 800°C, the memory window width was 0.9 V at ±5 V. The leakage current density of Pt/SBT/CeO₂/Si structure annealed at 800°C was 4×10^?7 A/cm² at 5 V.     

Structural and improved electrical properties of rare earth (Sm, Tb and Ho) doped BiFe0.975Mn0.025O3 thin films

Pure BiFeO₃ (BFO) and rare earth (RE) ion co-doped (Bi_0.9RE_0.1)(Fe_0.975Mn_0.025)O₃ (RE?=?Sm, Tb and Ho, denoted by BSFM, BTFM and BHFM) thin films were prepared on Pt(111)/Ti/SiO₂/Si(100) substrates by using a chemical solution deposition method. Formations of distorted rhombohedral perovskite structure for the thin films were confirmed by using an X-ray diffraction and a Raman scattering analysis. Microstructural features for the thin films were examined by using a scanning electron microscopic analysis. Among the thin films, the lowest leakage current density of 1.22?×?10^?6 A/cm² (at 100 kV/cm), large remnant polarization (2Pr) of 72.4 μC/cm² and low coercive field (2E _c ) of 689 kV/cm (at 980 kV/cm) were measured for the BTFM thin film.     

Fabrication and characterization of Au/SBT/LZO/Si MFIS structure

Ferroelectric SrBi₂Ta₂O₉ (SBT) films on a p-type Si (100) wafer with a LaZrO _x (LZO) buffer layer have been fabricated to form a metal-ferroelectric-insulator–semiconductor (MFIS) structure. The LZO thin film and SBT films were deposited by using a sol–gel method. The equivalent oxide thickness (EOT) value of the LZO thin film was about 8.83 nm. Also, the leakage current density of the LZO thin film is about 3.3?×?10^?5 A/cm² at bias sweeping voltage of ±5 V. SBT films were crystallized in polycrystalline phase with highly preferred (115) orientation. Also, the intensity of each pick slightly increased as thickness of SBT films increased. The C–V characteristics of Au/SBT/LZO/Si structure showed clockwise hysteresis loop. The memory window width increased as the thickness of SBT films increased. The leakage current density of Au/SBT/LZO/Si structure decreased as thickness of SBT films increased.