Study on the electrical and optical properties of ITO and AZO thin film by oxygen gas flow rate

Transparent conductive oxide (TCO) thin films such as tin doped indium oxide (ITO), zinc doped indium oxide (IZO) and Al doped zinc oxide (AZO) have been widely used as transparent electrode for display. ITO and AZO thin films for display was prepared by the facing targets sputtering (FTS) system. The FTS method is called a plasma-free sputter method because the substrate is located apart from plasma. This system can deposit the thin film with low bombardment by high energetic particles in plasma such as γ-electrons, negative ions and reflected Ar atoms. ITO and AZO thin films were deposited on glass substrate at room temperature with oxygen gas flow rate and input power. And the electrical, structural and optical properties of the thin films were investigated. As a result, the resistivity of ITO, AZO thin film is 6?×?10^?4 Ω cm, 1?×?10^?3 Ω cm, respectively. And the optical transmittance of as-deposited thin films is over 80% at visible range.     

Characterization of the CeO2 thin films for insulation layer and Pt/SrBi2Ta2O9/CeO2/Si MFISFET structure

Abstract

CeO₂ and SrBi₂Ta₂O₉ (SBT) thin films for MFISFET (metal-fcrroelectrics-insulator-semiconductor field effect transistor) were deposited by rf sputtering and pulsed laser deposition method, respectively. The effects of oxygen partial pressure during deposition for CeO₂ films were investigated. The oxygen partial pressure significantly affected the preferred orientation, grain size and electrical properties of CeO₂ films. The CeO₂ thin films with a (200) preferred orientation were deposited on Si(100) substrates at 600°C. The films deposited under the oxygen partial pressure of 50 % showed the best C-V characteristics among those under various conditions. The leakage current density of films showed order of the 10^?7～10^?8 A/cm² at 100 kV/cm. The SBT thin films on CeO₂/Si substrate showed dense microstructure of polycrystalline phase. From the C-V characteristics of MFIS structure composed of the SBT film annealed at 800°C, the memory window width was 0.9 V at ±5 V. The leakage current density of Pt/SBT/CeO₂/Si structure annealed at 800°C was 4×10^?7 A/cm² at 5 V.     

The effect of deposition temperature on the material and electrical properties of PZT thin films for ULSI DRAM applications

Abstract

The effects of deposition temperature on the properties of thin films of sputtered lead-zirconate-titanate (PZT) have been studied for ULSI DRAM storage capacitor dielectric applications. The films were deposited by reactive dc magnetron sputtering from a multi-component target. The grain size for the films deposited at 400°C was found to be less than 1000 Å, while it was ～ 10–30 μm for films deposited at 200°C. Small grain-sized material is desirable since it leads to better cell-to-cell uniformity in terms of charge storage capacity and other electrical and reliability properties. The optimum lead compensation was found to increase as the deposition temperature (T _dep) increased. Leakage current density stays fairly constant as T _dep is varied. As-deposited films, with a deposition temperature of 500°C, were rich in the perovskite phase and showed a high charge storage density of 11.2 μC/cm² and a low leakage current density of 5.1 × 10^?7 A/cm² (both at 1.5 V). This implies the possibility of eliminating the high temperature crystallization-annealing step.     

Effects of sputtering pressure and thickness on properties of ZnO:Al films deposited on polymer substrates

Highly conducting and transparent aluminum doped zinc oxide (ZnO:Al) thin films have been deposited on polyimide substrate by r.f. magnetron sputtering at room temperature. The influence of sputter pressure and thickness on the structural, electrical, and optical properties of ZnO:Al films deposited on polyimide substrate is reported. The crystallinity and degree of orientation was increased by decreasing the sputter pressure. For higher sputtering pressures an increase on the resistivity was observed due to a decrease on the mobility and the carrier concentration. As the film thickness was increased, the crystallite sizes were increased, but the average transmittance in the wavelength range of the visible spectrum was decreased. The electrical performances of the ZnO:Al films deposited on glass substrates are slightly worse than the ones of the films deposited on polyimide substrates with same thickness. The lowest resistivity of 8.6?×?10^?4 Ω cm can be obtained for films deposited on glass substrate with the thickness of 800 nm.     

INFLUENCE OF DEPOSITION TEMPERATURE AND N2 FLOW RATE ON HIGH QUALITY ZNO THIN FILM DEPOSITED ON SiO2/SI SUBSTRATE BY ULTRASONIC SPRAY PYROLYSIS

ABSTRACT

ZnO thin films were prepared on SiO₂/Si substrate by ultrasonic spray pyrolysis (USP) method using the aqueous solution of zinc acetate dehydrate. X-ray diffraction (XRD) and atomic force microscopy (AFM) were employed to analyze the crystalline and microscopic structure of the films. The properties of ZnO films were investigated with respect to deposition temperature (T_s) and N₂ flow rate (f). The results show that ZnO thin films exhibit hexagonal wurtzite structure and the highly preferential orientation along c-axis under T_s = 320°C and f = 5 L/min deposition condition.     

Preparation and properties of sputtered lead titanate thin films on MgO single crystals and mgo buffer layers

Abstract

By means of planar multitarget sputtering (001) oriented PbTiO₃ films were deposited onto highly preferred (100) oriented platinum electrodes on (100) MgO single crystal substrates. Single phase perovskite type films with a degree of (001) orientation between 60% and 70% have been sputtered at substrate temperatures as low as about 470°C. The as grown films exhibit a dielectric constant in the range of 120 to 140 and a pyroelectric coefficient of about 20 nCcm^?2K^?1 at room temperature. The dielectric loss is about 0.01 at frequencies from 1 to 10 kHz. (100) GaAs substrates with an evaporated, highly oriented (100) MgO buffer layer were also used as substrates. However, on these substrates the platinum bottom electrode did not grow highly oriented though the same deposition parameters for Pt deposition as in the case of the single crystalline MgO substrate were used. That's why PbTiO₃ was produced with a lower (001) preferred orientation. Therefore, the dielectric constant is higher (170–190) and the pyroelectric coefficient is lower (12 nCcm^?2K^?1).     

Characteristics of ZnO thin film for film bulk acoustic-wave resonators

Highly c-axis-oriented zinc oxide (ZnO) thin films were deposited on Au electrodes by reactive radio frequency (RF) magnetron sputtering and their sputtering pressure on thin film bulk acoustic-wave resonator (FBAR) characteristics are presented. The evolution of the preferred orientation and the surface morphologies of the deposited ZnO films are investigated using X-ray diffraction, scanning electron microscopy, and atomic force microscopy measurement techniques. The result obtained in this study show that the ZnO films prepared using a lower sputtering pressure of 2?×?10^?3 Torr have a strong c-axis orientation, promote smoother surface and higher resonance frequency. The experimental results demonstrate that the fabricated two-port FBAR using the optimum process parameters yields an effective electromechanical coupling constant ( $ k^{2}_{{{\text{eff}}}} $ ) of 2.8%, series quality factor (Q _s) of 436, and a parallel quality factor (Q _p) of 600.     

Electrical and optical studies of transparent conducting ZnO:Al thin films by magnetron dc sputtering

Transparent conducting aluminium-doped Zinc oxide (ZnO:Al) films have been deposited on glass substrates by magnetron dc sputtering using a ceramic target (ZnO with 2 wt% Al₂O₃). The dependence of the electrical and optical properties of these films on substrate temperature, sputtering pressure of Ar and location of substrates were investigated in detail. Target is perpendicular with substrate and we controlled the distance ‘x’ of target and substrate. Optimized films with resistivity of 3.7?×?10^?4 Ω cm, an average transmission in the visible range (300–800 nm) of greater than 85% and the reflectance in the infrared range being greater than 85% have been formed. Substrate temperature, distance ‘x’, and working pressure are optimized for lower resistivity and high concentration of carriers.     

Physical properties of transparent conducting indium doped zinc oxide thin films deposited by pulsed DC magnetron sputtering

Transparent conducting In-doped (1at.%) zinc oxide (IZO) thin films are deposited on glass substrate by bipolar pulsed DC magnetron sputtering. We have investigated the effect of pulse frequency on the physical properties of the IZO films. A highly c-axis oriented IZO thin films were grown in perpendicular to the substrate. At optimal deposition conditions, IZO films with a smoothest surface roughness of ～3.6 nm, a low-resistivity of 5.8?×?10^?3 Ωcm, and a high mobility of 14 cm/Vs were achieved. The optical spectra showed a high transmittance of above 85% in the UV–visible region and exhibited the absorption edge of near 350 nm. In micro-Raman, we observed the three phonon modes of host ZnO, which are E ₂ ^low, E ₂ ^high, and A ₁ modes, and the three additional modes. The origin of three additional modes is attributed to the host lattice defect due to the effect of In dopant and increasing the pulse frequency.     

Growth characteristics and film properties of gallium doped zinc oxide prepared by atomic layer deposition

We carried out comprehensive studies on structural, optical, and electrical properties of gallium-doped zinc oxide (Ga:ZnO) films deposited by atomic layer deposition (ALD). The gallium(III) isopropoxide (GTIP) was used as a Ga precursor, which showed pure Ga₂O₃ thin film with high growth rate. Using this precursor, conductive Ga doped ZnO thin film can be successfully deposited. The electrical, structural and optical properties were systematically investigated as functions of the Ga doping contents and deposition temperature. The best carrier concentration and transmittance (7.2?×?10²⁰ cm^?3 and 83.5 %) with low resistivity (≈3.5?×?10^?3?Ωcm) were observed at 5 at.% Ga doping concentration deposited at 250 °C. Also, low correlation of deposition temperature with the carrier concentration and film structure was observed. This can be explained by the almost same atomic radius of Ga and Zn atom.     

Fabrication and characterization of Au/SBT/LZO/Si MFIS structure

Ferroelectric SrBi₂Ta₂O₉ (SBT) films on a p-type Si (100) wafer with a LaZrO _x (LZO) buffer layer have been fabricated to form a metal-ferroelectric-insulator–semiconductor (MFIS) structure. The LZO thin film and SBT films were deposited by using a sol–gel method. The equivalent oxide thickness (EOT) value of the LZO thin film was about 8.83 nm. Also, the leakage current density of the LZO thin film is about 3.3?×?10^?5 A/cm² at bias sweeping voltage of ±5 V. SBT films were crystallized in polycrystalline phase with highly preferred (115) orientation. Also, the intensity of each pick slightly increased as thickness of SBT films increased. The C–V characteristics of Au/SBT/LZO/Si structure showed clockwise hysteresis loop. The memory window width increased as the thickness of SBT films increased. The leakage current density of Au/SBT/LZO/Si structure decreased as thickness of SBT films increased.     

Multiferroic,magnetoelectric and magneto-impedance properties of NiFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/(Pb,Sr) TiO<Subscript>3</Subscript> bilayer films

We prepared NiFe₂O₄/(Pb, Sr)TiO₃ (NFO/PST) bilayer films by the chemical solution method and investigated their multiferroic, magnetoelectric and magneto-impedance properties. Multiferroic properties have been observed at room temperature. The bilayer films exhibit saturation polarization P _s ? 26.6 μC/cm² and saturation magnetization M _s ? 134 emu/cm³. With increasing Sr content, M _s. and P _s values of the NFO/PST bilayer films decrease. The variation may be ascribed to the influence of interfacial strain and decrease in tetragonality. High magnetoelectric coupling effect has been observed in the NFO/PST bilayer films with maximum value of α _E  = 6.35 Vcm^?1 Oe^?1 measured at H _DC  ~ 1 kOe and f ~ 10 kHz for Sr ~ 10% (NFO/PST10). The magneto-impedance measurements establish a strong dependence on magnetic field, further confirming magnetoelectric response in NFO/PST bilayer films. An alternative approach for impedance analysis of NFO/PST10 bilayer film provides direct evidence of strain mediated magnetoelectric coupling at room temperature. The results indicate that NFO/PST bilayer films can be considered as a potential multiferroic magnetoelectric material.     

Characteristics of Bi4Ti3O12 thin films on ITO/glass and Pt/Si substrates prepared by R.F. sputtering and rapid thermal annealing

Bi₄Ti₃O₁₂ thin films are deposited on ITO/glass and Pt/Ti/Si(100) substrates by R.F. magnetron sputtering at room temperature. The films are then heated by a rapid thermal annealing (RTA) process conducted in oxygen atmosphere at temperatures ranging from 550–700^∘C. X-ray diffraction examination reveals that the crystalinity of the films grown on Pt/Ti/Si is better than that of the films grown on ITO/glass under the same fabrication conditions. SEM observation shows that the films grown on Pt/Ti/Si are denser than those grown on ITO/glass substrates. Interactive diffusion between the Bi₄Ti₃O₁₂ film and the ITO film increases with the increase of annealing temperature. The optical transmittance of the thin film annealed at 650^∘C is found to be almost 100% when the effect of the ITO film is excluded. The relative dielectric constants, leakage currents and polarization characteristics of the two films are compared and discussed.     

Preparation of BaPbO3 Electrode Thin Films by RF Magnetron Sputtering

For electrode materials of Pb(Zr,Ti)O₃ (PZT) thin films in ferroelectric random access memory (FeRAM), various materials have been studied. As new electrode material with which the polarization and fatigue properties are improved, we take notice of barium metaplumbate BaPbO₃ (BPO). Because the BPO contained lead (Pb) and oxygen is conductor that adopted same perovskite structure as PZT. BPO thin films were prepared by rf magnetron sputtering on various substrates. (SiO₂/Si, MgO, Al₂O₃ and Pt-coated substrates), and influence of growth conditions (sputtering gas, rf power, the substrate-heating temperature and post anneals) on crystallization and conductivity were investigated. In case of post anneal after sputtering at room temperature, perovskite single phase was obtained above 400°C. In case of substrate heating while sputtering, without post anneal, perovskite single phase was obtained at 350–500°C on SiO₂/Si substrates (110) preferred orientation BPO films obtained at low temperature, and resistivity of the films decreased at decreasing sputtering temperature. Resistivity of the film at substrate temperature 350°C was 3 × 10^?3 Ω cm. In the case of single crystal substrate, the BPO films were epitaxially grown. Orientation of the films was varied with the sputtering condition. The epitaxial PZT thin films were also grown on the BPO, revealing that PZT(111)[011] //BPO(111)[011] //Pt(100)[011] //MgO(100)[011] and PZT(111)[011] //BPO(111)[011] //Pt(111)[011] //Al₂O₃(001)[100] structures were obtained, and their ferroelectric properties were also evaluated.     

Effect of fluorine doping on the properties of ZnO films deposited by radio frequency magnetron sputtering

ZnO films with varying fluorine content were prepared on Corning glass by radio frequency magnetron sputtering of ZnO target containing ZnF₂ at room temperature, and the compositional, electrical, optical, and structural properties of the as-grown films together with the vacuum-annealed films were investigated. The fluorine content in the fluorine doped ZnO (FZO) films increased almost linearly with increasing ZnF₂ content in sputter target, and the highest atomic concentration was 7.3%. Vacuum-annealing caused a slight reduction of fluorine content in the films. The resistivity of the as-grown FZO films deposited showed a typical valley-like behavior with respect to the fluorine content in film, i.e. having minimum resistivity at intermediate fluorine content. Despite high fluorine content in the FZO films, the carrier concentration remained below 1.2?×?10²⁰ cm^?3, leading to very low doping efficiency level. Upon vacuum-annealing, the resistivity of FZO films decreased substantially due to increase in both the carrier concentration and the Hall mobility. From the structural analysis made by X-ray diffraction study, it was shown that addition of small amount of fluorine enhanced the crystallinity of FZO films with (002) preferred orientation, and that large amount of fluorine addition yielded disruption of preferred orientation. It was also shown that doping of fluorine rendered a beneficial effect in reducing the absorption loss of ZnO films in visible range, thereby substantially enhancing the figure of merit.     

Electrical and optical properties of microwave dielectric thin films prepared by pulsed laser deposition

Abstract

Bi₂(Zn_1/3Nb_2/3)₂O₇, BiZN, materials possess high dielectric constant and low loss factor in microwave frequency region. They have good potential for device application, especially in the form of thin films. However, the microwave dielectric properties of a thin film are very difficult to be accurately measured. Evaluation on the dielectric behavior of the films through the performance of the microstrip line devices made of these films involves metallic conduction and stray field losses. A novel measuring technique, which can directly evaluate the microwave dielectric properties of a thin film is thus urgently needed.

In this paper, BiZN thin films were grown on [100] MgO single crystal substrates using pulsed laser deposition process. The high-frequency dielectric properties of thus obtained thin films were determined using optical transmission spectroscopy (OTS). The [100] preferentially oriented films with pyrochlore structure can be obtained for the thin films deposited at 400–600°C substrate temperature under 0.1 mbar oxygen pressure. OTS measurements reveal that the index of refraction (n=1.95–2.35) and absorption coefficient (k=0.28x10^?4-2.25 × 10^?4 nm^?1) of the films vary insignificantly with the crystallinity of the BiZN films.     

Epitaxial ferroelectric Pb(Mg1/3Nb2/3)O3-PbTiO3 thin films on La0.7Sr0.3MnO3 bottom electrode

Epitaxial (001)-oriented 0.7Pb(Mg_0.33Nb_0.67)O₃-0.3PbTiO₃ (PMN-PT) thin films were deposited by pulsed laser deposition on vicinal SrTiO₃ (001) substrates using La_0.7Sr_0.3MnO₃ as bottom electrode. Detailed microstructural investigations of these films were carried out using X-ray diffraction (XRD), atomic force microscopy (AFM) and transmission electron microscopy (TEM). Polarization-field hysteresis curves were measured at room temperature. Spontaneous polarization P _s , remnant polarization P _r and coercive voltage V _c were found to be 25 μC/cm², 15 μC/cm² and 0.81 V, respectively. Field dependent dielectric constant measurements exhibited butterfly shaped curves, indicating the true ferroelectric nature of these films at room temperature. The dielectric constant and the dielectric loss at 100 kHz were found to be 238 and 0.14, respectively. The local piezoelectric properties of PMN-PT films were investigated by piezoelectric force microscopy and were found to exhibit a local piezoelectric coefficient of 7.8 pm/V.     

Low‐resistive and transparent AZO films prepared by PLD in magnetic field

Al₂O₃‐doped ZnO (AZO) thin films have been deposited onto glass substrates using a split target consisting of AZO (1 wt%) and AZO (2 wt%) by pulsed laser deposition with an ArF excimer laser (λ = 193 nm, 15 mJ, 10 Hz, 0.75 J/cm²). By applying a magnetic field perpendicular to the plume, the lowest resistivity of 8.54 × 10^?5Ω·cm and an average transmittance exceeding 91% over the visible range were obtained at a target‐to‐substrate distance of 25 mm for approximately 279‐nm‐thick AZO film (1.8 wt%) grown at a substrate temperature of 230 °C in vacuum. From cross‐sectional TEM observations and the XRD spectrum, a reason why the low resistivity (54 × 10^?5Ω·cm) was reproducibly obtained was considered to be due to the fact that a disorder of crystal growth originating in the vicinity of the interface between the substrate and the film was suppressed by application of the magnetic field and the c‐axis orientation took preference, giving rise to the increase of mobility. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 151(2): 40–45, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20026     

Fabrication and operation limit of lead-free PTCR ceramics using BaTiO3–(Bi1/2Na1/2)TiO3 system

The electric properties of BaTiO₃–(Bi_1/2Na_1/2)TiO₃ (BT–BNT) solid solution ceramics were studied as a lead-free PTCR (positive temperature coefficient of resistivity) thermistor material usable over 130°C. For determining the maximum switching temperature T _s, the phase diagram of BT–BNT binary system was clarified. Two semiconductorization processes and their electric properties are described. The lanthanum(La)-doped BBNT ceramics sintered in air still showed dielectric behaviors, but the niobium(Nb)-doped ones had a low resistivity at room temperature, ρ _RT, on the order of 10³ Ωcm and showed a PTC behavior. Sintering under a low O₂ atmosphere produces BT–BNT ceramics with less than 10² Ωcm compared to those prepared in air. Our current research produced the BBNT ceramics with T _s values around 210°C by increasing the (Bi_1/2Na_1/2) content in the ceramics.     

Effect of Deposition Temperature on the Electrochromic Properties of Electron Beam-Evaporated WO3 Thin Films

Tungsten oxide (WO₃) thin films were deposited on ITO/glass substrates using the electron beam evaporation technique. The WO₃ films were grown on substrates at temperatures varying from room temperature (RT) to 240 °C. The structural characterization and surface morphology were examined using X-ray diffraction (XRD) and a field emission scanning electron microscope (FE-SEM). The electrochromic properties of WO₃ thin films were investigated using cyclic voltammograms (CVs) and in situ transmittance measurements, which were performed on WO₃ thin films immersed in an electrolyte of 1 M LiClO₄ in propylene carbonate (PC). An amorphous 510-nm-thick WO₃ film heated at RT exhibits the maximum transmittance variation (ΔT%) of 61.8% between the bleached state and the colored state, with a ΔOD of 0.739, Q of 17.31 mC/cm² and η of 42.69 cm²/C at a wavelength (λ) of 550 nm.