The inhibitive effect of poly(p‐toluidine) on corrosion of iron in 1M HCL solutions

In recent years, polymer amines have been recognized as an excellent corrosion inhibitors for iron in acid solutions. In this work, the inhibitive effect of p‐toluidine and poly(p‐toluidine) on corrosion of iron in 1M HCl has been studied by the electrochemical methods such as impedance, linear polarization, Tafel polarization techniques. The effectiveness of poly(p‐toluidine) was found to be high in comparison with that of monomer. The results showed that p‐toluidine and poly(p‐toluidine) suppressed both cathodic and anodic processes of iron dissolution in 1M HCl. The inhibition efficiency of both p‐toluidine and poly(p‐toluidine) were found to increase with the inhibitor concentrations. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Photoemission and conductivity measurement of poly(N‐methyl aniline) and poly(N‐ethyl aniline) films

The studies involve the X‐ray photoelectron spectroscopy (XPS) and conductivity measurements of poly(N‐methyl aniline) and poly(N‐ethyl aniline) films deposited electrochemically at different pH values of −0.96, 2.22, and 3.78 for N‐methyl aniline and 1.10, 2.22, and 3.78 for N‐ethyl aniline. The results obtained reveal significant differences in the film properties of the two matrices as a function of pH of solution. These differences are explained on the basis of the competitive reaction products formed during polymerization in the two matrices along with the differences in the electron‐donating ability of the methyl and ethyl groups present on the nitrogen (N) atom. These results are further supported by the UV–Visible and IR data. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1286–1292, 1999     

Performance evaluation of poly (methacrylic acid) as corrosion inhibitor in the presence of iodide ions for mild steel in H2SO4 solution

The inhibition performance of poly (methacrylic acid) (PMAA) and the effect of addition of iodide ions on the inhibition efficiency for mild steel corrosion in 0.5 M H₂SO₄ solution were investigated in the temperature range of 303–333 K using electrochemical, weight loss, scanning electron microscopy (SEM), and water contact angles measurements. The results show that PMAA is a moderate inhibitor for mild steel in 0.5 M H₂SO₄ solution. Addition of small amount of KI to PMAA significantly upgraded the inhibition efficiency up to 96.7%. The adsorption properties of PMAA and PMAA + KI are estimated by considering thermodynamic and kinetic parameters. The results reveal that PMAA alone was physically adsorbed onto the mild steel surface, while comprehensive adsorption mode characterized the adsorption of PMAA + KI. Adsorption of PMAA and PMAA + KI followed Temkin adsorption isotherm. The SEM and water contact angle images confirmed the enhanced PMAA film formation on mild steel surface by iodide ions.     

Investigation on the microstructure and the electric property of poly(propylene)/chlorinated poly(propylene)/poly(aniline) composites

The article presents results of studies on composites made from poly(propylene) (PP) modified with poly(aniline) (PANI) doped with dodecylbenzene sulfonic acid (DBSA) and chlorinated poly(propylene) (CPP). The volume resistivity of PP/CPP/PANI composites was detected, and the results show that the volume resistivity decreases with increasing CPP content, and there exists a minimum volume resistivity. Effects of CPP on the microstructure and crystalline structure of the PP/CPP/PANI composites and the relationship between the effects and the electric property were carefully analyzed by scanning electron microscope (SEM) and wide angle X‐ray diffraction (WAXD). The method that the specimens of SEM are polished is appropriate to investigate the morphology of conducting polymer composites. The obtained results illuminate that the area of conducting parts and insulating parts obtained from the digital analysis of the SEM image is obviously influenced by the CPP content, the parameters of the lamellar‐like structure are immediately related to CPP content and denote the dispersion of PANI‐DBSA, and the percent crystallinity and mean crystal size of PP are directly correlated with the CPP content. The increasing area of conducting parts, the increasement of layer distance, the decreasement of size and layer number of the lamellar‐like structure of PANI‐DBSA, and the increasement of the percent crystallinity and mean crystal size of PP are beneficial to the improvement of the conductive property of PP/CPP/PANI composites. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Studies on the dielectric properties of poly(o‐toluidine) and poly(o‐toluidine‐aniline) copolymer

Poly(o‐toluidine) (PoT) and poly(o‐toluidine co aniline) were prepared by using ammonium persulfate initiator, in the presence of 1M HCl. It was dried under different conditions: room temperature drying (48 h), oven drying (at 50°C for 12 h), or vacuum drying (under vacuum, at room temperature for 16 h). The dielectric properties, such as dielectric loss, conductivity, dielectric constant, dielectric heating coefficient, loss tangent, etc., were studied at microwave frequencies. A cavity perturbation technique was used for the study. The dielectric properties were found to be related to the frequency and drying conditions. Also, the copolymer showed better properties compared to PoT alone. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 592–598, 2004     

Influence of molecular weight of poly(ortho‐ethoxyaniline) on the corrosion inhibition efficiency of mild steel in acidic media

The present work revealed that the chemical polymerization of ortho‐ethoxyaniline yields two types of polymers not only with different spectroscopic properties but also with different molecular weights: (1) a green form, which corresponds to the high molecular weight fraction of the polymer with a molecular weight of 800,000 g mol^?1 based on the polystyrene calibration. It is mainly composed of quinoid and benzoid structures, which is an indication of a half‐oxidized polymer (emeraldine). This form of the polymer is insoluble in water‐miscible solvents like ethanol and methanol and thus cannot be tested in terms of corrosion inhibition efficiency; (2) a red form, which corresponds to the low molecular weight fraction of the polymer with a molecular weight of 44,000 g mol^?1. It is composed mostly of quinoid structures and exhibits an oxidation state similar to that of the completely oxidized polymer (pernigraniline). In our case, the polymer fraction, which is soluble in alcohol, was first tested as a corrosion inhibitor for mild steel in acidic media, not only at conventional molecular weight (44,000 g mol^?1) but also at different molecular weights. These different molecular weights of the polymer were obtained by adding varying amounts of neutral salt to the synthesis environment. Next, the effect of the molecular weight of the red form of the polymer on the corrosion inhibition efficiency of mild steel in hydrochloric acid solutions was investigated. The obtained results showed that the adsorption of the polymer alcoholic form obeys a Temkin adsorption isotherm with no significant change as function of inhibition efficiencies for a series of molecular weights ranging from13,000 to 124,000 g mol^?1. The effect of temperature on the corrosion behavior of mild steel in 1M HCl with addition of 100 ppm of the alcoholic form of poly(ortho‐ethoxyaniline) was studied in the temperature range 25–60°C. The associated activation corrosion energy was determined. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1275–1284, 2004     

Performance assessment of poly (methacrylic acid)/silver nanoparticles composite as corrosion inhibitor for aluminium in acidic environment

This article reports the preparation of poly (methacrylic acid)/silver nanoparticles composite (PMAA/AgNPs) by in situ mixing of aqueous solutions of PMAA and 1 mM AgNO₃ with natural honey as reducing and stabilizing agent. The prepared PMAA/AgNPs composite was characterized by UV–vis spectroscopy, Fourier transformed infrared, X-ray diffraction and energy dispersive spectroscopy (EDS) while the morphology of the AgNPs in the composite was obtained by transmission electron microscopy (TEM). TEM results revealed that the AgNPs were spherical in shape. The performance of PMAA/AgNPs composite as anticorrosion material for Al in acidic environment was examined by electrochemical, weight loss methods, complemented by surface analysis characterization with scanning electron microscopy (SEM), EDS and water contact angle measurements. Results obtained indicate that PMAA/AgNPs composite is effective corrosion inhibitor for Al in an acid-induced corrosive environment. Inhibition efficiency increased with increase in composite concentration but decreased with rise in temperature. From potentiodynamic polarization results, PMAA/AgNPs composite is found to function as a mixed-type corrosion inhibitor. The adsorption of the composite onto Al surface was found to follow El-Awady et al. adsorption isotherm model. SEM, EDS and water contact angle results confirmed the adsorption of the composite on Al surface.     

Studies of electrochemically deposited poly(N-methyl aniline) films

The effect of surface resistance of substrate and concentration of monomer on the properties of electrochemically deposited poly(N-methyl aniline) films has been investigated. The UV–visible spectra of the films show enhanced selectivity in the formation of the conducting phase (approximately 860nm) of polymer on lower surface resistance substrate (10Ω/□) over those with higher surface resistance (50Ω/□). The magnitude of selectivity increases with concentration of monomer. These results are further supported by IR analysis of the samples. From morphological studies it is noted that the films deposited on 10Ω/□ substrates exhibit an overall granular nature irrespective of concentration of monomer. In the case of films deposited on 50Ω/□ substrates sequential changes in patterning are observed with increasing concentration of monomer. Two redox couples are observed in the cyclic voltammograms together with distortion of peak potential in the films obtained on higher surface resistance substrates. © SCI 1998.     

Preparation and electrochemical capacitance of poly(pyrrole‐co‐aniline)

The copolymer of pyrrole and aniline, poly(pyrrole‐co‐aniline), has been prepared by chemical oxidation of corresponding monomer mixtures with ammonium peroxysulfate. Techniques of FTIR, SEM‐EDS, and BET surface area measurement were used to characterize the structure and morphology of the copolymer. The electrochemical properties of the copolymer were investigated by cyclic voltammetry, galvanostatic charge‐discharge, and electrochemical impedance spectroscopy. The results indicated that poly(pyrrole‐co‐aniline) was about 100–300 nm in diameter and showed better electrochemical capacitive performance than polypyrrole and polyaniline. The specific capacitance of the copolymer electrode was 827 F/g at a current of 8 mA/cm² in 1 mol/L Na₂SO₄ electrolyte. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Doped poly (2,5‐dimethyl aniline) for the detection of ethanol

Poly (2,5‐dimethyl aniline) (P25DMA), with and without NiO and ZnO as dopants, is evaluated as a sensing material for ethanol to detect transdermal ethanol emissions. Three sensing materials—P25DMA, P25DMA doped with 20 wt % NiO, and P25DMA doped with 20 wt % ZnO—are eventually deposited onto a radio frequency identification sensor. The limit of detection for the materials is found to be 3, 24, and 420 ppm, respectively. Also, all three sensing materials are selective toward ethanol with benzene and methanol used as interferents. The response and recovery times are also measured for the three sensing materials and are in the order of seconds, which is acceptable for a transdermal ethanol sensor. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42259.     

Electrochemical study of the adsorption and inhibiting properties of halogen derivatives of aniline on iron in sulfuric acid

The adsorption of halogen derivatives of aniline on an iron electrode in sulfuric acid medium has been studied in relation to their inhibiting properties using electrochemical a.c. impedance and d.c. polarization techniques, as well as quantum chemical calculations of chemical structure and distribution of electron charges in the organic molecules. It is established that the adsorption process is described by Frumkin's isotherm. The adsorption parameters characterizing the interaction forces between the molecules in the adsorbed layer, the free energy of adsorption, the maximum surface excess of adsorbed species, the area occupied by each molecule etc. have been calculated on the basis of this isotherm. It is shown that the inhibition efficiency, as well as the free energy of adsorption, increases in the sequence: aniline < p-Cl-aniline < p-Br-aniline < p-I-aniline. It was found that the adsorption behaviour of the substances studied is characterized by two adsorption states: vertical and planar orientation of the molecules. Combining data from electrochemical measurements with data from quantum chemical calculations the correlation between the chemical structure of the aniline derivatives and their adsorption capability and inhibition efficiency has been ascertained.     

Chemical grafting of aniline and o‐toluidine onto poly(ethylene terephthalate) fiber

Graft copolymerization of poly(aniline) and poly(o‐toluidine) onto poly(ethylene terephthalate) fiber was conducted by using peroxydisulfate as a lone initiator under nitrogen atmosphere at various experimental conditions in aqueous hydrochloric acid medium. The grafting of poly(aniline) and poly(o‐toluidine) onto poly(ethylene terephthalate) fiber was verified by recording cyclic voltammetry of the grafted fiber, conductivity measurements, and thermal analysis. Graft parameters—such as % grafting, % efficiency, and the rate of grafting—were followed. Grafting was always accompanied by homopolymerization. The rate of homopolymerization was also followed in all experimental conditions. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 121–128, 1999     

Adsorption of heavy‐metal ions on poly(ethylene imine)‐immobilized poly(methyl methacrylate) microspheres

Poly(methyl methacrylate) (PMMA) microspheres carrying poly(ethylene imine) (PEI) were prepared for the removal of heavy‐metal ions (copper, cadmium, and lead) from aqueous solutions with different amounts of these ions (50–600 mg/L) and different pH values (3.0–7.0). Ester groups in the PMMA structures were converted to imine groups in a reaction with PEI as a metal‐chelating ligand in the presence of NaH. The adsorption of heavy‐metal ions on the unmodified PMMA microspheres was very low [3.6 μmol/g for Cu(II), 4.6 μmol/g for Cd(II), and 4.2 μmol/g for Pb(II)]. PEI immobilization significantly increased the heavy‐metal adsorption [0.224 mmol/g for Cu(II), 0.276 mmol/g for Cd(II), and 0.126 mmol/g for Pb(II)]. The affinity order of adsorption (in moles) was Cd(II) > Cu(II) > Pb(II). The adsorption of heavy‐metal ions increased with increasing pH and reached a plateau value around pH 5.5. Their adsorption behavior was approximately described with the Langmuir equation. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 197–205, 2001     

Improved processability and performance of biomedical devices with poly(lactic acid)/poly(ethylene glycol) blends

To improve the processability of micropolymer‐based devices used for biomedical applications, poly(lactic acid) (PLA) was melt‐blended with poly(ethylene glycol)s (PEGs) of different molecular weights (MWs; weight‐average MWs = 200, 800, 2000, and 4000; these PEGS are referred to as PEG200, PEG800, PEG2000, and PEG4000, respectively, in this article). The thermal properties, mechanical properties, and rheological properties of the PLA and the PLA–PEG blends were investigated. The tensile samples’ morphologies showed that the low‐MW PEGs filled molds well. The rheological properties confirmed that the low‐MW PEGs decreased the complex viscosity, and improved the processability. With decreasing PEG MW, the PLA glass‐transition temperature decreased. The nanoindenter data show that the addition of PEG decreased the modulus and hardness of PLA. The morphologies of the tensile samples showed that with increasing PEG MW, the thicknesses of the core layers increased gradually. The elongation at break was improved by approximately 247% with the addition of PEG200. Such methods can produce easily processed biological materials for producing biomedical products. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45194.     

Thermal behavior of poly(acrylic acid)–poly(vinyl pyrrolidone) and poly(acrylic acid)–metal–poly(vinyl pyrrolidone) complexes

Thermal analysis (TGA and DTA) of samples of PAA, PVP, PAA–PVP complexes, containing different weight fractions of PAA and ternary polymer–metal–polymer complexes, were studied. The activation energy parameters for the thermal degradation were also calculated. The study of the effect of FeCl₃, NiCl₂, and Ni(NO₃)₂ on the TGA and DTA curves of the complexes showed that the decompositions are dependent on the concentrations and the nature of the metal ions. The DTA traces of PAA–PVP complex containing FeCl₃, NiCl₂, and Ni(NO₃)₂ showed that the treatment of the complex with these metal ions causes considerable changes in the thermal decomposition of PAA–PVP complex. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4049–4057, 2006     

Complexation between poly(methacrylic acid) and poly(vinylpyrrolidone)

The complexation between poly(methacrylic acid) (PMAA) and poly(vinylpyrrolidone) (PVP) in aqueous phase was studied by various fluorescence techniques, including fluorescence anisotropy measurements, fluorescence probe studies, and nonradiation energy transfer. It was demonstrated that the complexation of PMAA with PVP occurs within a pH range of 1 to 5 and along with complexation, the conformation of PMAA changed from a hypercoiled to a loosely coiled form. The complex ratio between the two polymers is 2:1 (PMAA/PVP, in monomer unit). Salt effect studies showed that the complexation occurred due to formation of hydrogen bonds between the two polymers. Based on these conclusions and the “connected cluster model” for PMAA at low pH, a “ladder with connected cluster” model was proposed for the structure of PMAA/PVP complex formed at low pH. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 620–627, 2001     

Relationship between the crystallization behavior of poly(ethylene glycol) and stereocomplex crystallization of poly(L‐lactic acid)/poly(D‐lactic acid)

Poly(l ‐lactic acid) (PLLA) is a good biomedical polymer material with wide applications. The addition of poly(ethylene glycol) (PEG) as a plasticizer and the formation of stereocomplex crystals (SCs) have been proved to be effective methods for improving the crystallization of PLLA, which will promote its heat resistance. In this work, the crystallization behavior of PEG and PLLA/poly(d ‐lactic acid) (PDLA) in PLLA/PDLA/PEG and PEG‐b‐PLLA/PEG‐b‐PDLA blends has been investigated using differential scanning calorimetry, polarized optical microscopy and X‐ray diffraction. Both SCs and homocrystals (HCs) were observed in blends with asymmetric mass ratio of PLLA/PDLA, while exclusively SCs were observed in blends with approximately equal mass ratio of PLLA/PDLA. The crystallization of PEG was only observed for the symmetric blends of PLLA_39k/PDLA_35k/PEG_2k, PLLA_39k/PDLA_35k/PEG_5k, PLLA_69k/PDLA_96k/PEG_5k and PEG‐b‐PLLA_31k/PEG‐b‐PDLA_27k, where the mass ratio of PLLA/PDLA was approximately 1/1. The results demonstrated that the formation of exclusively SCs would facilitate the crystallization of PEG, while the existence of both HCs and SCs could restrict the crystallization of PEG. The crystallization of PEG is related to the crystallinity of PLLA and PDLA, which will be promoted by the formation of SCs. © 2017 Society of Chemical Industry     

Comparison of poly(o‐anisidine) and poly(o‐anisidine‐co‐aniline) copolymer synthesized by chemical oxidative method

In this study, poly(o‐anisidine) [POA], poly(o‐anisidine‐co‐aniline) [POA‐co‐A], and polyaniline [PANi] were chemically synthesized using a single polymerization process with aniline and o‐anisidine as the respective monomers. During the polymerization process, p‐toluene sulfonic acid monohydrate was used as a dopant while ammonium persulfate was used as an oxidant. N‐methyl‐pyrolidone (NMP) was used as a solvent. We observed that the ATR spectra of POA‐co‐A showed features similar to those of PANi and POA as well as additional ones. POA‐co‐A also achieved broader and more extended UV–vis absorption than POA but less than PANi. The chemical and electronic structure of the product of polymerization was studied using Attenuated Total Reflectance spectroscopy (ATR) and UV–visible spectroscopy (UV–vis). The transition temperature of the homopolymers and copolymers was studied using differential scanning calorimetry and the viscosity average molecular weight was studied by using dilute solution viscometry. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Biodegradable polymer blends of poly(lactic acid) and poly(ethylene glycol)

Poly(lactic acid) (PLA) and poly(ethylene glycol) (PEG) were melt-blended and extruded into films in the PLA/PEG ratios of 100/0, 90/10, 70/30, 50/50, and 30/70. It was concluded from the differential scanning calorimetry and dynamic mechanical analysis results that PLA/PEG blends range from miscible to partially miscible, depending on the concentration. Below 50% PEG content the PEG plasticized the PLA, yielding higher elongations and lower modulus values. Above 50% PEG content the blend morphology was driven by the increasing crystallinity of PEG, resulting in an increase in modulus and a corresponding decrease in elongation at break. The tensile strength was found to decrease in a linear fashion with increasing PEG content. Results obtained from enzymatic degradation show that the weight loss for all of the blends was significantly greater than that for the pure PLA. When the PEG content was 30% or lower, weight loss was found to be primarily due to enzymatic degradation of the PLA. Above 30% PEG content, the weight loss was found to be mainly due to the dissolution of PEG. During hydrolytic degradation, for PLA/PEG blends up to 30% PEG, weight loss occurs as a combination of degradation of PLA and dissolution of PEG. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 1495–1505, 1997     

Interpolymer complexes of poly(acrylamide) and poly(N-isopropylacrylamide) with poly(acrylic acid): a comparative study

The interpolymer complexation, through successive hydrogen bonding, between poly(acrylamide) (PAAm) and poly(N-isopropylacrylamide) (PNiPAAm) with poly(acrylic acid) (PAA) in aqueous solution has been viscometrically and potentiometrically investigated. The stoichiometry of the complexes formed was determined. By comparing the strength of the two complexes the very important contribution of the hydrophobic interaction in their formation has been indicated.