Soluble microbial products in membrane bioreactor operation: Behaviors, characteristics, and fouling potential

This paper presents an experimental study on soluble microbial products (SMP) in membrane bioreactor (MBR) operation at different sludge retention times (SRTs). A laboratory-scale MBR was operated at SRT of 10, 20, and 40 days for treatment of readily biodegradable synthetic wastewater. The accumulation, composition, characteristics, and fouling potential of SMP at each SRT were examined. It was found that accumulation of SMP in the MBR became more pronounced at short SRTs. Carbohydrates and proteins appeared to be the components of SMP prone to accumulate in the MBR compared with aromatic compounds. The proportions of SMP with large molecular weight in supernatants and in effluents were almost identical, implying that membrane sieving did not work for most SMP. In addition, the majority of SMP was found to be composed of hydrophobic components, whose proportion in total SMP gradually increased as SRT lengthened. However, fouling potentials of SMP were relatively low at long SRTs. The hydrophilic neutrals (e.g., carbohydrates) were most likely the main foulants responsible for high fouling potentials of SMP observed at short SRTs.     

Chelating properties and molecular weight distribution of soluble microbial products from an aerobic membrane bioreactor

This paper presents a detailed study on soluble microbial products (SMPs) in an aerobic membrane bioreactor (MBR) treating synthetic wastewater simulating municipal wastewater. The concentration of SMP in the reactor conformed to a cyclical pattern of accumulation and reduction in relation to SRT. The molecular weight (MW) distribution of accumulated SMP was determined to vary from <1kD to >100kD. Copper chelating properties of various SMP fractions in the MBR were compared before and after copper addition to the feed. The conditional stability constant (LogcK), complexation capacity (Cc), and SMP-ligand concentration (CL) were evaluated to determine the impact of copper on the chelating properties. The results indicated that accumulated SMP in the aerobic MBRs without copper addition are moderate chelators with LogcK values of 7.6-8.3 mol(-1) for the moderate ligands and 6.3-6.8 mol(-1) for the relatively weaker ligands. SMPs with MW of 1-10 kD were found to have the highest complexation capacity among all SMP fractions. The complexation capacity of accumulated SMP after feeding copper was 0.11 micromol/mg of SMP, almost half of its value prior to feeding copper. The reduction of C(c) after feeding copper was a result of an increase in large molecular weight SMP (>100 kD).     

Characterization of soluble microbial products from anaerobic treatment by molecular weight distribution and nickel-chelating properties

Nine anaerobic chemostats fed glucose as the sole carbon and energy source were used to investigate the characteristics of soluble microbial products (SMP). These reactors were maintained at solids retention times (SRT) of 15, 25, and 40 days (3 reactors for each SRT) with organic loading rates of 0.25 or 0.50 g COD/1-d. Results showed that the concentration of SMP increased with increasing SRT (steady-state SMP for 15-, 25-, and 40-d systems were 54, 126, and 291 mg COD/1, respectively). Distribution of SMP among three molecular weight categories (MW < 1000 daltons, 1000 < MW < 10,000, and MW > 10,000) was bimodal. The fraction of SMP with MW > 10,000 was found to increase with increasing SRT (34 mg/l and 48% of total SMP for a 15-d SRT, 83 mg/l and 62% for a 25-d SRT, and 242 mg/l and 76% for a 40-d system). The stability constant (^cK) between Ni and SMP was approximately 10^3.62, a value very similar to some naturally occurring organic acids. The total SMP-ligand concentration (C_T,L) ranged from 0.07 to 1.33 mM as Ni and increased with increasing SRT. The complexation capacity ranged from 0.65 to 5.97 μmol of Ni/mg SMP, and was independent of SRT with an average of 2.49 μmol of Ni/mg SMP.     

Changes in characteristics of soluble microbial products in membrane bioreactors associated with different solid retention times: Relation to membrane fouling

A membrane bioreactor (MBR) is a promising wastewater treatment technology, but there is a need for efficient control of membrane fouling, which increases operational and maintenance costs. Soluble microbial products (SMP) have been reported to act as major foulants in the operation of MBRs used for wastewater treatment. In this study, SMP in MBRs operated with different sludge retention times (SRTs) were investigated by means of various analytical techniques and their relations to the evolution of membrane fouling were considered. Bench-scale filtration experiments were carried out in a laboratory with synthetic wastewater to eliminate fluctuations that would occur with the use of real wastewater and that would lead to fluctuations in compositions of SMP. Three identical submerged MBRs were operated for about 50 days under the same conditions except for SRT (17, 51 and 102 days). Accumulation of SMP in the MBRs estimated by conventional analytical methods (i.e., the phenol-sulfuric acid method and the Lowry method) was significant in the cases of short SRTs. However, the degrees of membrane fouling in the MBRs were not directly related to the concentrations of SMP in the reactors estimated by the conventional analytical methods. Non-conventional analytical methods such as excitation-emission matrix (EEM) fluorescence spectroscopy revealed that characteristics of SMP in the three reactors considerably differed depending on SRT. Foulants were extracted from the fouled membranes at the end of the operation and were compared with SMP in each MBR. It was clearly shown that characteristics of the foulants were different depending on SRT, and similarities between SMP and the extracted foulants were recognized in each MBR on the basis of results of EEM measurements. However, such similarities were not found on the basis of results obtained by using the conventional methods for analysis of SMP. The results of this study suggest that the use of conventional methods for analysis of SMP is not appropriate for investigation of membrane fouling in MBRs.     

MBR膜丝表面生物膜对出水水质的稳定作用

在膜生物反应器（MBR）发生溶解性微生物产物（SMP）积累的情况下,对新膜与旧膜的出水水质进行了比较.结果表明,旧膜具有比新膜更为稳定和良好的出水水质,其出水平均TOC浓度为12.9 mg/L,低于新膜出水的36.8 mg/L,表明膜丝表面的生物膜强化了系统对SMP的截留能力.MBR上清液中分子质量＞10 ku的大分子物质与分子质量＜3 ku的小分子物质占有相当大的比例,旧膜对所有分子质量物质的截留效果均优于新膜.旧膜经清洗后,其出水的TOC浓度随着膜比通量的下降而降低.     

Modelling the production and degradation of soluble microbial products (SMP) in membrane bioreactors (MBR)

MBR biochemical conditions have an effect on membrane fouling and SMP have been attributed to be the main MBR foulant. Thus, predicting the SMP concentration is essential for understanding and controlling MBR fouling. However, existing SMP models are mostly too complex and over-parameterized, resulting in inadequate or absent parameter estimation and validation. This study extends the existing activated sludge model No. 2d (ASM2d) to ASM2dSMP with introduction of only 4 additional SMP-related parameters. Dynamic batch experimental results were used for SMP parameter estimation leading to reasonable parameter confidence intervals. Finally, the ASM2dSMP model was used to predict the impact of operational parameters on SMP concentration. It would found that solid retention time (SRT) is the key parameter controlling the SMP concentration. A lower SRT increased the utilization associated products (UAP) concentration, but decreased the biomass associated products (BAP) concentration and vice versa. A SRT resulting in minimum total SMP concentration can be predicted, and is found to be a relatively low value in the MBR. If MBRs operate under dynamic conditions and biological nutrient removal is required, a moderate SRT condition should be applied.     

Submerged anaerobic membrane bioreactor for low-strength wastewater treatment: Effect of HRT and SRT on treatment performance and membrane fouling

Three 6-L submerged anaerobic membrane bioreactors (SAnMBRs) with solids retention times (SRTs) of 30, 60 and infinite days were setup for treating synthetic low-strength wastewater at hydraulic retention times (HRTs) of 12, 10 and 8 h. Total COD removal efficiencies higher than 97% were achieved at all operating conditions. Maximum biogas production rate was 0.056 L CH₄/g MLVSS d at an infinite SRT. A shorter HRT or longer SRT increased biogas production due to increased organic loading rate or enhanced dominancy of methanogenics. A decrease in HRT enhanced growth of biomass and accumulation of soluble microbial products (SMP), which accelerated membrane fouling. A drop in carbohydrate to protein ratio also inversely affected fouling. At 12-h HRT, the effect of SRT on biomass concentration in SAnMBRs was negligible and membrane fouling was controlled by variant surface modification due to different SMP compositions, i.e., higher carbohydrate and protein concentrations in SMP at longer SRT resulted in higher membrane fouling rate. At 8 and 10-h HRTs, infinite SRT in SAnMBR caused highest MLSS and SMP concentrations, which sped up particle deposition and biocake/biofilm development. At longer SRT, lower extracellular polymeric substances reduced flocculation of particulates and particle sizes, further aggravated membrane fouling.     

Denitrification from drinking water using a membrane bioreactor: chemical and biochemical feasibility

Interest is growing in developing membrane bioreactors (MBRs) to replace ion exchange for nitrate removal from drinking water. However, few published studies have successfully managed to retain exogenous or biologically derived carbon. This study determined an optimum C:N by substrate breakthrough rather than maximum nitrate removal. By dosing 相似文献   

Reduced membrane fouling in a novel bio-entrapped membrane reactor for treatment of food and beverage processing wastewater

A novel Bio-Entrapped Membrane Reactor (BEMR) packed with bio-ball carriers was constructed and investigated for organics removal and membrane fouling by soluble microbial products (SMP). An objective was to evaluate the stability of the filtration process in membrane bioreactors through backwashing and chemical cleaning. The novel BEMR was compared to a conventional membrane bioreactor (CMBR) on performance, with both treating identical wastewater from a food and beverage processing plant. The new reactor has a longer sludge retention time (SRT) and lower mixed liquor suspended solids (MLSS) content than does the conventional. Three different hydraulic retention times (HRTs) of 6, 9, and 12 h were studied. The results show faster rise of the transmembrane pressure (TMP) with decreasing hydraulic retention time (HRT) in both reactors, where most significant membrane fouling was associated with high SMP (consisting of carbohydrate and protein) contents that were prevalent at the shortest HRT of 6 h. Membrane fouling was improved in the new reactor, which led to a longer membrane service period with the new reactor. Rapid membrane fouling was attributed to increased production of biomass and SMP, as in the conventional reactor. SMP of 10-100 kDa from both MBRs were predominant with more than 70% of the SMP <100 kDa. Protein was the major component of SMP rather than carbohydrate in both reactors. The new reactor sustained operation at constant permeate flux that required seven times less frequent chemical cleaning than did the conventional reactor. The new BEMR offers effective organics removal while reducing membrane fouling.     

Novel electrokinetic approach reduces membrane fouling

An innovative submerged membrane electro-bioreactor (SMEBR) was built to reduce membrane fouling through a combination of various electrokinetic processes. The objective of this research was to assess the capability of SMEBR to reduce fouling under different process conditions. At the bench scale level, using synthetic wastewater, membrane fouling of the SMEBR was compared to the fouling of a membrane bioreactor (MBR) in five runs. Different protein concentrations in the influent synthetic wastewater were selected to develop different membrane fouling potentials: high (240 mg/l), low (80 mg/l) and zero protein addition. The MBR and SMEBR were operated at a flux equal to the membrane critical flux in order to create high fouling rate conditions. Membrane fouling rate, expressed as the change in the trans-membrane pressure per day (kPa/d), decreased in the SMEBR 5.8 times (standard deviation (SD) = 2.4) for high protein wastewater, 5.1 times (SD = 2.4) for low protein content, and 1.3 times (SD = 0.7) for zero protein, when compared to the MBR. The supernatant concentrations of the soluble microbial products (SMP) were 195–210, 65–135 and less than 65 mg/l in respective experimental series. Following the bench scale study, membrane fouling was assessed in a pilot scale SMEBR, fed with raw un-clarified municipal wastewater, and operated under real-sewage variable quality conditions. The pilot SMEBR exhibited three times smaller membrane fouling rate than the MBR. It was concluded that electrokinetic processes generated by SMEBR led to a reduction of membrane fouling through: i) removal of soluble microbial products (mainly protein and polysaccharides) and colloidal organic materials; ii) change of the structure and morphology of the suspended solids due their conditioning by DC field.     

Accumulation of biopolymer clusters in a submerged membrane bioreactor and its effect on membrane fouling

A laboratory-scale submerged membrane bioreactor (SMBR) with a hollow-fibre membrane module was used to investigate membrane fouling under various operational conditions. The results showed that the sludge supernatant inside the SMBR had a consistently higher organic content than the MBR effluent. Detailed analysis revealed a pool of organic substances, classified as biopolymer clusters (BPC), in the SMBR system that were larger in size than the soluble microbial products (SMP). The BPC content in the MBR sludge mixture ranged from 0.7 to 18.8 mg/L in terms of the total organic carbon (TOC), with an average of 5.6+/-3.5mg/L, which was about twice the SMP concentration in the suspension. Under a fluorescent microscope and using DAPI staining, the BPC in the sludge supernatant after centrifugation were found to be particulate organic substances that were independent of the sludge flocs and had a size distribution up to 50 microm. The findings of the experiment suggest that BPC are an important foulant and have a profound effect on membrane fouling. The fouling rate in the reactor, as indicated by the increase in trans-membrane pressure (TMP), correlates to a certain extent with the BPC concentration in the sludge suspension under various conditions. It is argued that BPC are a special form of organic substances that are formed by the adsorption and affinity clustering of mainly SMP within the sludge layer deposited on the membrane surface. The BPC can be detached with the sludge from the membrane and returned to the suspension. The accumulation of BPC in the SMBR sludge mixture would facilitate the formation of a sludge fouling layer on the membrane surface, thus causing a serious fouling problem.     

Relation between EPS adherence, viscoelastic properties, and MBR operation: Biofouling study with QCM-D

Membrane fouling is one of the main constraints of the wide use of membrane bioreactor (MBR) technology. The biomass in MBR systems includes extracellular polymeric substances (EPS), metabolic products of active microbial secretion that adversely affect the membrane performance. Solids retention time (SRT) in the MBR is one of the most important parameters affecting membrane fouling in MBR systems, where fouling is minimized at optimal SRT. Among the operating parameters in MBR systems, SRT is known to strongly influence the ratio of proteins to polysaccharides in the EPS matrix. In this study, we have direct evidence for changes in EPS adherence and viscoelastic properties due to changes in the sludge removal rate that strongly correlate with the membrane fouling rate and EPS composition. EPS were extracted from a UF membrane in a hybrid growth MBR operated at sludge removal rates of 59, 35.4, 17.7, and 5.9 L day^-1 (corresponding SRT of 3, 5, 10, and 30 days, respectively). The EPS adherence and adsorption kinetics were carried out in a quartz crystal microbalance with dissipation monitoring (QCM-D) technology in several adsorption measurements to a gold sensor coated with Polyvinylidene Fluoride (PVDF). EPS adsorption to the sensor surface is characterized by a decrease of the oscillation frequency and an increase in the dissipation energy of the sensor during parallel flow of aqueous media, supplemented with EPS, above the sensor surface. The results from these experiments were further modeled using the Voigt based model, in which the thickness, shear modulus, and shear viscosity values of the adsorbed EPS layers on the PVDF crystal were calculated. The observations in the QCM-D suggested that the elevated fouling of the UF membrane is due to higher adherence of the EPS as well as reduction in viscosity and elasticity of the EPS adsorbed layer and elevation of the EPS fluidity. These results corroborate with confocal laser scanning microscopy (CLSM) image analysis showing thicker EPS in close proximity to the membrane surface operated at reactor conditions which induced more fouling at elevated sludge removal rates.     

Impact of ambient conditions on SMP elimination and rejection in MBRs

The widespread application of the membrane-assisted activated sludge process is restricted by membrane fouling, which increases investment and operating costs. Soluble microbial products (SMPs) are currently considered as the major cause of membrane fouling in membrane bioreactors (MBRs). This study aims at elucidating and quantifying the effects of varying environmental conditions on SMP elimination and rejection based on findings in a pilot MBR and in well-defined lab trials. Several factors are thought to influence the concentration of SMP and their fouling propensity in one way or the other, but findings are often inconsistent or even contradictory. Here, SMP loading rate was found to have the greatest effect on SMP elimination and thus on concentration in the MBR. The degree of elimination decreased at very low DO and low nitrate concentrations. On average, 75% of influent SMP were eliminated in both pilot and lab trials, with the elimination of polysaccharides (PS) mostly above 80%. Rejection of SMP components by the used membrane (PAN, 37nm) ranged mainly from 20% to 70% for proteins and from 75% to 100% for PS. Especially protein rejection decreased at higher temperatures and higher nitrification activity. The increased fouling rates at lower temperatures might therefore partly be explained by this increased rejection. Apparently, mainly the nitrite-oxidising community is responsible for the formation for smaller SMP molecules that can pass the membrane.     

Correlation of EPS content in activated sludge at different sludge retention times with membrane fouling phenomena

In this study, activated sludge characteristics were studied with regard to membrane fouling in membrane bioreactors (MBRs) for two pilot plants and one full-scale plant treating municipal wastewater. For the full-scale MBR, concentrations of extracellular polymeric substances (EPS) bound to sludge flocs were shown to have seasonal variations from as low as 17mgg(-1) dry matter (DM) in summer up to 51mg(gDM)(-1) in winter, which correlated with an increased occurrence of filamentous bacteria in the colder season. Therefore, it was investigated at pilot-scale MBRs with different sludge retention times (SRTs) whether different EPS contents and corresponding sludge properties influence membrane fouling. Activated sludge from the pilot MBR with low SRT (23d) was found to have worse filterability, settleability and dewaterability. Photometric analysis of EPS extracts as well as LC-OCD measurements showed that it contained significantly higher concentrations of floc-bound EPS than sludge at higher SRT (40d) The formation of fouling layers on the membranes, characterised by SEM-EDX as well as photometric analysis of EPS extracts, was more distinct at lower SRT where concentrations of deposited EPS were 40-fold higher for proteins and 5-fold higher for carbohydrates compared with the membrane at higher SRT. Floc-bound EPS and metals were suggested to play a role in the fouling process at the full-scale MBR and this was confirmed by the pilot-scale study. However, despite the different sludge properties, the permeability of membranes was found to be similar.     

A comparison of membrane fouling under constant and variable organic loadings in submerge membrane bioreactors

The aim of this study is to compare the effect of constant and variable influent organic loadings on membrane fouling in submerged membrane bioreactors (sMBRs). Two identical lab-scale sMBRs were operated for 162 days at an SRT of 30 days, whereas the influent organic loading was kept constant in one MBR, and varied in another. The microbial characteristics of sludge in terms of MLSS, bound EPS, EPS in the supernatant and particle size distribution were investigated in order to evaluate their respective effect on membrane fouling. During the start-up period, membrane fouling in the MBR fed with variable loadings was more serious than that in the MBR with the constant loading. However, at the stable state, the fouling tendency was clearly reversed with less membrane fouling for variable feed strength. It was shown that the contents of polysaccharides in the supernatant and particle size of the bioflocs were responsible for the observed differences in the fouling tendencies of the two MBRs.     

淹没式膜生物反应器膜面泥饼层的微结构特征

为研究膜生物反应器运行中的膜污染问题,利用扫描电镜（SEM）和原子力显微镜（AFM）分析了膜在污泥混合液及上清液中所形成泥饼层的微结构特征.结果表明,两种类型泥饼层的微结构存在显著差异且与膜污染速度相关,膜面泥饼层微结构的表征技术可以作为膜污染评价的重要手段.在污泥混合液中形成的膜面泥饼层厚度大但表面粗糙度高,存在一定的孔隙性;而在上清液中形成的膜面泥饼层虽然更薄但相对致密,其渗透性差,导致膜污染速度加快.活性污泥混合液及上清液中,膜截留的溶解性微生物代谢产物（SMP）的分子质量分布趋势相近,膜面泥饼层微结构的差异主要与被过滤液中微生物絮体的体积和含量有关.     

Saline sewage treatment using a submerged anaerobic membrane reactor (SAMBR): Effects of activated carbon addition and biogas-sparging time

This study investigated the performance of a submerged anaerobic membrane reactor (SAMBR) treating saline sewage under fluctuating concentrations of salinity (0-35 g NaCl/L), at 8 and 20 h HRT, with fluxes ranging from 5-8 litres per square metre per hour (LMH). The SAMBRs attained a 99% removal of Dissolved Organic Carbon (DOC) with 35 g NaCl/L, while removal inside the reactor was significantly lower (40-60% DOC). Even with a sudden drop in salinity overall removal recovered quickly, while the recovery inside the reactor took place at a slower rate. This highlights the positive effect of the membrane in preventing the presence of high molecular weight organics in the effluent while also retaining biomass inside the reactor so that they can rapidly acclimatize to salinity. The reduction of continuous biogas sparging to intervals of 10 min ON and 5 min OFF resulted in a slight increase in transmembrane pressure (TMP) by 0.025 bar, but also resulted in an increase in effluent DOC removal and inside the SAMBR by 10% and 20%, respectively. The addition of powdered activated carbon (PAC) resulted in a decrease in the TMP by 0.070 bar, and an increase in DOC removal in the reactor and effluent by 30% and 5%, respectively. The PAC dramatically decreased the high molecular weight organics in the reactor over a period of 72 h. SEM pictures of the membrane and biomass before and after addition of PAC revealed a remarkable reduction of flocks on the membrane surface, and a reduction inside the reactor of soluble microbial products (SMPs). Finally, Energy Dispersive X-ray (EDX) analysis of the membranes pores and biofilm highlighted the absence of organic matter in the inner pores of the membrane.     

Mechanisms of SMP production in membrane bioreactors: Choosing an appropriate mathematical model structure

Being able to predict the soluble microbial product (SMP) concentration, an important foulant in membrane bioreactors (MBRs), with mathematical models provides the opportunity to use foulant production as an MBR design and optimization parameter. This study examined the ability of three mathematical model structures to describe two distinct mechanisms of SMP production. The production mechanisms evaluated are (1) the erosion or hydrolysis of floc-associated extracellular polymeric substance (EPS) and (2) decay of active cells. The models were compared based on their ability to predict SMP concentrations observed in an MBR system during a period of increased SMP and floc-associated EPS production due to increased predation. Predation was an important contributor to overall biomass decay. Short-term batch experiments were also preformed to examine model assumptions related to the (1) production of SMP due to decay of active cells, (2) production of SMP due to erosion of floc-associated EPS, (3) degradability of SMP present in the MBR mixed liquor during increased predation and (4) degradability of eroded floc-associated EPS. Both erosion of floc-associated EPS and decay of active cells were shown to be important independent mechanisms of SMP production. Therefore, a mathematical model used to predict SMP concentrations should provide the ability to capture both mechanisms independently. SMP produced during increased predation were slowly degradable while eroded floc-associated EPS was rapidly degradable. Model results demonstrate that the slowly biodegradable SMP fraction will dominate the bulk phase SMP concentration.     

Characterization of soluble microbial products (SMP) under stressful conditions

Soluble microbial products (SMP) in the wastewater treatment process not only cause fouling to the membrane, but also generate disinfection by-products (DBP) in the effluent, thus get increasing attention. In this study, SMP produced by activated sludge and isolates under different stressful conditions, i.e. starvation, salinity, heavy metals, low pH and high temperature, were characterized to investigate the effects of these conditions on the amount of SMP and their compositions. The analysis results using size exclusion chromatography (SEC), high pressure liquid chromatography (HPLC) and fluorescence excitation emission matrix (FEEM) showed that activated sludge and isolates suffered with the same stressful condition contained almost the same concentration and composition of SMP, indicating that the stressful condition instead of the microbial species played the crucial role in the production of SMP. Among of stressful conditions tested, high temperature had stimulated the production of polysaccharides and polycarboxylate-type humic acid with high hydrophilicity, which is in positive proportion to the foulants formation potential, thus should be avoided in membrane bioreactors. Low pH had promoted the generation of hydrophobic humic acid-like or protein-like organics, which had been proved as the main disinfection byproduct (DBP) precursor, thus should be avoided in the biological treatment. Starvation had less effect on SMP production as the seeding microbes had no substrates.     

Membrane bioreactor process for removing biodegradable organic matter from water

This research investigated a membrane bioreactor (MBR) process for removing biodegradable organic matter (BOM) and trihalomethane (THM) precursors from pre-ozonated water. Bench-scale and mini-pilot-scale MBR experiments were conducted using powdered activated carbon (PAC) and acclimated biomass. Dissolved organic carbon (DOC) was removed through a combination of adsorption and biodegradation mechanisms, and the initial DOC removals depended on carbon dose, while steady-state removals were in the 20-60 percent range under various operating conditions. Both assimilable organic carbon (AOC) and total aldehydes were mostly removed to near detection limits and were not affected by PAC dosage. The AOC(NOX) removals were significantly higher than AOC(P17) or total AOC removals probably because the MBR microbial consortium was closer in characteristics to Aquaspirillum NOX than to Pseudomonas fluorescens (P17). The DOC was used instead of biodegradable organic carbon (BDOC) as a parameter for evaluating disinfection byproduct formation and bacterial regrowth potentials because BDOC assays did not yield consistent and conclusive results due to analytical difficulties. The removals of THM precursors were high when PAC was added; however, steady-state removals were a function of operating conditions and PAC dosage. Addition of PAC enhanced DOC removals and membrane permeate fluxes. Furthermore, pre-ozonation reduced membrane fouling and enhanced membrane permeate flux.