Preparation and luminescent properties of CaTiO<Subscript>3</Subscript>: Pr<Superscript>3+</Superscript>, Al<Superscript>3+</Superscript> persistent phosphors by nitrate-citric acid combustion method

Using citric acid as reducing agent and fuel, nitrate as a oxidant, boric acid as a flux material, red persistent phosphors CaTiO₃: Pr³⁺, Al³⁺ have been successfully synthesized by nitrate-citric acid combustion method. The best route is determined by studying influences of the amount of citric acid and ammonium nitrate, pH value of the solution, initiating temperature of furnace, and the amount of boric acid. The photoluminescence and crystallinity of persistent phosphors were investigated by using luminescence spectrometer and X-ray diffractometer (XRD), respectively. The results show that the optimum molar ratio of citric acid to calcium nitrate was about 0.8 and that of boric acid to calcium nitrate was about 0.4. Photoluminescence and decay curves show that the samples exhibited the optimal luminous properties at pH value of 6 and at the initiating temperature of 700 °C.     

Preparation and characterization of Eu<Superscript>3+</Superscript> activated CaSiO<Subscript>3</Subscript>, (CaA)SiO<Subscript>3</Subscript> [A = Ba or Sr] phosphors

Eu³⁺ activated CaSiO₃, (Ca, Ba) SiO₃ and (Ca, Sr) SiO₃ have been prepared by sol-gel technique. Residual solvent and organic contents in the gel were removed by firing at 100°C for 3–4 h at 300 and 600°C for 2 h. Small exothermic shoulder around 850 to 875°C, as observed in DTA curve, corresponds to crystallization temperature of the doped calcium silicate. Influence of firing temperature on the luminescence of Eu³⁺ shows the maximum emission intensity in gel fired at 850°C. Photoluminescence emission peak is observed at 614 nm due to⁵D₀ →⁷F₂ transition of Eu³⁺ ion in (Ca, Ba) SiO₃ and (Ca, Sr) SiO₃ phosphors, when excited by 254 nm. The (Ca, Ba) SiO₃ material is proposed as an efficient red phosphor.     

Optical properties of Eu<Superscript>3+</Superscript> activated SrLa<Subscript>2</Subscript>O<Subscript>4</Subscript> red-emitting phosphors for WLED applications

The SrLa_2?xO₄:xEu³⁺ phosphors are synthesized through high-temperature solid-state reaction method at 1473 K with various doping concentration. Their phase structures, absorption spectra, and luminescence properties are investigated by X-ray diffraction (XRD), UV–Vis spectrophotometer and photoluminescence spectrometry. The intense absorption of SrLa_2?xO₄:xEu³⁺ phosphors have occurred around 400 nm. The prominent luminescence spectra of the prepared phosphors exhibited bright red emission at 626 nm. The doping concentration 0.12 mol% of Eu³⁺ is shown to be optimal for prominent red emission and chromaticity coordinates are x?=?0.692, y?=?0.3072. Considering the high colour purity and appropriate emission intensity of Eu³⁺ doped SrLa₂O₄ can be used as red phosphors for white light emitting diodes (WLEDs).     

Photoluminescence properties of a novel red-emitting phosphor Ba<Subscript>2</Subscript>LaV<Subscript>3</Subscript>O<Subscript>11</Subscript>:Eu<Superscript>3+</Superscript>

Ba₂LaV₃O₁₁:Eu³⁺ phosphors were firstly synthesized by the traditional solid-state reaction method at 1100 °C. Their luminescence properties were investigated by photoluminescence excitation and emission spectra. The excitation spectrum shows a broad band centered at about 275 nm in the region from 200 to 370 nm, which is attributed to an overlap of the charge transfer transitions of O^2??→?V⁵⁺ and O^2??→?Eu³⁺. The phosphors exhibit the red emissions of Eu³⁺ and the emission intensity ratio of ⁵D₀?→?⁷F₂ to ⁵D₀?→?⁷F₁ is dependent on the Eu³⁺ concentration due to an environment change about Eu³⁺ ions. Concentration quenching occurs at 30 mol% in the phosphors and exchange interaction is its main mechanism. Ba₂LaV₃O₁₁:Eu³⁺ displays tunable CIE color coordinates from yellow orange to red depended on Eu³⁺ content, which may have a potential application for illuminating and display devices.     

Synthesis and luminescence properties of a novel UV-emitting phosphor Sr<Subscript>3</Subscript>P<Subscript>4</Subscript>O<Subscript>13</Subscript>:Ce<Superscript>3+</Superscript>

The ultraviolet (UV)-emitting Sr₃P₄O₁₃:Ce³⁺ phosphors were synthesized via the solid-state reaction method, and their structural, morphological and luminescence properties were characterized by X-ray diffraction analysis, scanning electron microscopy, photoluminescence spectroscopy. The obtained results indicate that these phosphors can be effectively excited by short-wavelength ultraviolet (<300 nm), and exhibit long-wavelength ultraviolet (300–380 nm) emission with nanosecond-level fluorescence lifetime corresponding to the parity-allowed 5d–4f transitions of Ce³⁺. The concentration-quenching phenomenon of Ce³⁺ in Sr₃P₄O₁₃ host was also studied, in which the critical energy transfer distance between Ce³⁺ ions and concentration quenching mechanism were determined.     

Tunable luminescence of SrLaMgTaO<Subscript>6</Subscript>:Sm<Superscript>3+</Superscript> phosphors due to energy transfer from TaO<Subscript>6</Subscript> group to Sm<Superscript>3+</Superscript> ion

A series of SrLaMgTaO₆:Sm³⁺ phosphors were synthesized through a solid state reaction. The phase, microstructure and luminescent properties of the synthesized phosphors were investigated through techniques of XRD, SEM and spectrophotometer. The XRD patterns show that the synthesized phosphors have the same phase structure. The SEM images show that the synthesized phosphors are microcrystallines in the range of 1.2–3.4 µm. SrLaMgTaO₆:Sm³⁺ phosphors present emission bands originating from TaO₆ group and Sm³⁺ ions. The critical concentration of Sm³⁺ in SrLaMgTaO₆ is found to be 7 mol%. Due to energy transfer from TaO₆ group to Sm³⁺, tunable luminescence is obtained by changing Sm³⁺ doping concentration.     

Preparation,spectroscopic properties and enhanced luminescence of Tb<Superscript>3+</Superscript>-doped LuAG phosphors and transparent ceramics by introduction of Sc<Superscript>3+</Superscript>

Tb-doped LuAG(lutetium aluminum garnet) and LuSAG(lutetium scandium-aluminum garnet) precursors were synthesized through a co-precipitation process, using ammonium hydrogen carbonate as precipitator. Single-phase cubic LuAG/Tb and LuSAG/Tb phosphors were obtained after calcination at 1000 and 1200 °C, respectively. These powders could be easily sintered into corresponding transparent LuAG/Tb and LuSAG/Tb ceramics in H₂ atmosphere at 1850 °C. The PL excitation and emission spectra were recorded for both phosphors and ceramics. Emission spectra of all materials were found to be typical for Tb³⁺, resulting from radiative relaxation of D level. Both the Tb-doped LuSAG phosphors and ceramics show higher efficient luminescence than LuAG , especially the transparent Tb-doped LuSAG ceramic shows about 150% higher luminescence intensity than transparent Tb-doped LuAG ceramic.     

Synthesis of (Y,Gd)<Subscript>3</Subscript>Al<Subscript>5</Subscript>O<Subscript>12</Subscript>:Ce nanophosphor by co-precipitation method and its luminescence behavior

(Y, Gd)₃Al₅O₁₂:Ce nanophosphor was synthesized by co-precipitation method using the mixture solution of ammonium liquor and ammonium hydrogen carbonate as precipitant. The effect of Ce and Gd concentration on the crystallization and luminescence behavior of the phosphor was studied. The results indicate (Y, Gd)₃Al₅O₁₂:Ce nanophosphor is obtained after the precipitates are sintered at 1,000 °C for 2 h. Following the increase of Ce and Gd concentration, the emission shows red shift.     

Cr<Superscript>3+</Superscript> activated Zn<Subscript>3</Subscript>Al<Subscript>2</Subscript>Ge<Subscript>3</Subscript>O<Subscript>12</Subscript>: a novel near-infrared long persistent phosphor

The near-infrared (NIR) long persistent phosphors have gained considerable attention owing to the potential applications in in vivo imaging. A novel NIR long-persistent phosphors Zn₃Al₂Ge₃O₁₂:Cr³⁺ was successfully synthesized by a high temperature solid-state reaction. The luminescent properties and the afterglow behaviors of the Zn₃Al₂Ge₃O₁₂:Cr³⁺ were investigated in detail. On the basis of thermoluminescence analyses, the mechanism of the persistent afterglow of the phosphors was also discussed briefly. The afterglow duration of this phosphor can last more than 12 h with the 650–750 nm emission range after stoppage of 254 nm ultraviolet light irradiation. Specifically, the persistent luminescence intensity and duration were regulated by changing Cr³⁺ doping concentration. All the results indicate that the Cr³⁺ activated Zn₃Al₂Ge₃O₁₂ has promising potential of practical applications.     

Synthesis,photoluminescence properties of Sr<Subscript>1.95</Subscript>Ba<Subscript>0.05</Subscript>CeO<Subscript>4</Subscript>:Eu<Superscript>3+</Superscript> for LED applications

The Sr_1.95Ba_0.05 CeO₄:Eu³⁺ phosphors are synthesized by the solid-state reaction method. The samples are characterized using X-ray diffraction (XRD), diffuse reflectance spectroscopy and photoluminescence (PL) spectra. The XRD results reveal that the synthesized phosphors are genuine crystalline and belong to the orthorhombic structure. The intense PL emission is optimized from the PL spectra at various doping concentrations of europium ions. The results indicates that the phosphor can be effectively excited under 264 nm wavelength producing on intense emission spectrum of the synthesis material at 484 nm (blue region). The color purity of the phosphor is confirmed by CIE coordinates (x = 0.217, y = 0.265). The experimental data indicate that the prepared phosphors can be used as blue-emitting material in the field of illuminations and display devices.     

Facile synthesis and characterization of MnO<Subscript>2</Subscript> nanomaterials as supercapacitor electrode materials

MnO₂ nanomaterials are synthesized via calcinations in air at various temperatures. Amorphous MnO₂ masses appear between 100 and 300 °C and nanorods form above 400 °C. Transmission and scanning electron microscopy are used to observe the geometries of each material, with further structural analyses conducted using X-ray photoelectron spectroscopy, X-ray diffraction, and BET method. The electrochemical properties are investigated through galvanostatic charge/discharge cycling, electrochemical impedance spectra, and cyclic voltammetry within a three-electrode test cell filled with 1 mol L^?1 Na₂SO₄ solution. The slightly asymmetric galvanostatic cycling curves suggest that the reversibility of the Faradaic reactions are imperfect, requiring a larger time to charge than discharge. The specific capacitances of each sample are calculated and trends are identified, proving that the samples synthesized at higher temperatures exhibit poorer electrochemical behaviors. The highest calculated specific capacitance is 175 F g^?1 by the sample calcinated at 400 °C. However, the lower temperature samples exhibit more favorable geometric properties and higher overall average specific capacitances. For future research, it is suggested that surface modifications such as a carbon coating could be used in conjunction with the MnO₂ nanorods to reach the electrochemical properties required by contemporary industrial applications.     

Up-converted ultraviolet luminescence of Er<Superscript>3+</Superscript>:BaGd<Subscript>2</Subscript>ZnO<Subscript>5</Subscript> phosphors for healthy illumination

Moderate level of exposure to the solar irradiation containing UV component is essential for health care. To incorporate the UV-emitting phosphors into the commercial YAG-based white light-emitting diode introduces the possibilities of healthy illumination to individuals’ daily lives. 1 mol.% Er³⁺-doped BaGd₂ZnO₅ (BGZ) particles were synthesized via sol-gel method and efficient up-converted luminescence peaked at 380 nm was detected under 480 nm excitation. The mixed phosphors with varied mass ratio of Er³⁺:BGZ and Ce³⁺:YAG particles were encapsulated to form LEDs. The study of the LEDs indicated that the introduction of BGZ component favored the enhancement of color-rendering index and the neutralization of the white light emitting. The WLED with the BGZ/YAG ratio of 8:2 was recommendable for its excellent overall white light luminous performances and UV intensity of 84.55 mW/cm². The UV illumination dose of the WLEDs with mixed YAG and BGZ was controllable by adjusting the ratio, the illumination distance and the illumination time. Er³⁺:BGZ phosphors are promising UVemitting phosphors for healthy indoor illumination.     

Synthesis of ultrafine ZrB<Subscript>2</Subscript> powders by sol-gel process

Ultrafine zirconium diboride (ZrB₂) powders have been synthesized by sol-gel process using zirconium oxychloride (ZrOCl₂·8H₂O), boric acid (H₃BO₃) and phenolic resin as sources of zirconia, boron oxide and carbon, respectively. The effects of the reaction temperature, B/Zr ratio, holding time, and EtOH/H₂O ratio on properties of the synthesized ZrB₂ powders were investigated. It was revealed that ultrafine (average crystallite size between 100 and 400 nm) ZrB₂ powders can be synthesized with the optimum processing parameters as follows: (i) the ratio of B/Zr is 4; (ii) the solvent is pure ethanol; (iii) the condition of carbothermal reduction heat treatment is at 1550°C for 20 min.     

Influence of Mn<Superscript>2+</Superscript> on the up-conversion emission performance of Mn<Superscript>2+</Superscript>, Yb<Superscript>3+</Superscript>, Er<Superscript>3+</Superscript>: ZnWO<Subscript>4</Subscript> green phosphors

The Mn²⁺, Yb³⁺, Er³⁺: ZnWO₄ green phosphors are synthesized successfully through the high temperature solid state reaction method. The micro-structure and morphology have been investigated by means of XRD and EDS. The doped concentrations of Mn²⁺, Yb³⁺, Er³⁺ are measured by ICP. The absorption spectra and emission spectra with different doped concentrations of Mn²⁺ are presented to reveal the influence of Mn²⁺ on the green up-conversion performance. Excited with 970 nm LED, the up-conversion emission peak at 547 nm is obtained and the CIE spectra as well as the green light photo are also presented. The results indicate that the Mn²⁺ ions play the role of the luminescence adjustment in the up-conversion process, which can improve the up-conversion green emission intensity effectively. The luminescence adjustment mechanism of Mn²⁺ ions in Mn²⁺, Yb³⁺, Er³⁺: ZnWO₄ green phosphors has been discussed. The crystal parameters of Dq, B and C are calculated to evaluate the energy level split effect.     

Thermochemical and luminescent properties of RbVO<Subscript>3</Subscript>, CsVO<Subscript>3</Subscript>, and Rb<Subscript>0.5</Subscript>Cs<Subscript>0.5</Subscript>VO<Subscript>3</Subscript>

RbVO₃, CsVO₃, and Rb_0.5Cs_0.5VO₃ have been synthesized by the Pechini process. The vanadates have an orthorhombic structure (sp. gr. Pbcm), melt congruently in the range 650–530°C, and undergo a reversible phase transition in the range 520–340°C. We have determined the onset temperatures and end points of the transformations at a temperature scan rate of 3°C/min and their enthalpies, and measured the photo-, roentgeno-, and cathodoluminescence and diffuse reflectance spectra of the vanadates. The luminescence spectra each are well fitted with three pseudo-Voigt functions. CsVO₃ has the highest integrated emission intensity. The emission intensity of the Rb_0.5Cs_0.5VO₃ solid solution is lower than that of the simple vanadates because of the optical absorption around its intrinsic luminescence band. This may be due to the presence of stable vacancy-type structural defects in Rb_0.5Cs_0.5VO₃.     

Preparation and characterization of a new long afterglow phosphor CaSnO<Subscript>3</Subscript>: Yb<Superscript>3+</Superscript>

A new phosphor CaSnO₃: Yb³⁺ was synthesized by a traditional solid-state reaction and the luminescent properties were investigated. The phosphors are well crystallized at 1200?°C. The excitation and the emission spectra show the characteristic broad of the Sn²⁺ ion and the X-ray photoelectron spectroscopy demonstrate the existence of Sn²⁺ ions caused by the doping of Yb³⁺ ions. The CaSnO₃: Yb³⁺ phosphor showed a typical afterglow behavior when the UV source was switched off. Thermal simulated luminescence study indicated that the persistent afterglow of CaSnO₃: Yb³⁺ phosphor was generated by the suitable electron or hole traps which were resulted from doping the calcium stannate host with rare-earth ions (Yb³⁺).     

Luminescence studies on Eu<Superscript>2+</Superscript> and Tb<Superscript>3+</Superscript> doped Ca<Subscript>2</Subscript>MgSi<Subscript>2</Subscript>O<Subscript>7</Subscript> phosphors

Eu²⁺ and Tb³⁺ doped Ca₂MgSi₂O₇ phosphors were synthesized by conventional solid-state reaction. The phase formation was confirmed by X-ray powder diffraction technique and refined lattice parameters were calculated by rietveld refinement process using Celref v3. The photoluminescence (PL) excitation and emission spectra were investigated. The phosphors exhibited broaden green emitting luminescence peaking at 520 nm when excited at 374 nm source. Morphological studies were carried out using Scanning electron microscopy (SEM) images of the sample with optimum PL emission. The dependence of photoluminescence intensity on co-dopant concentration and the kinetic parameters were also reported. Time resolved fluorescence spectroscopy (TRFS) is used to investigate the decay in luminescence signals with respect to time. The sample proved to be a good long lasting material, which makes it useful in emergency signs, textile printing, textile exit sign boards and electronic instrument dial pads etc.     

CO<Subscript>2</Subscript> gas sensitivity of sputtered zinc oxide thin films

For the first time, sputtered zinc oxide (ZnO) thin films have been used as a CO₂ gas sensor. Zinc oxide thin films have been synthesized using reactive d.c. sputtering method for gas sensor applications, in the deposition temperature range from 130–153°C at a chamber pressure of 8·5 mbar for 18 h. Argon and oxygen gases were used as sputtering and reactive gases, respectively. ZnO phase could be crystallized using a pure metal target of zinc. The structure of the films determined by means of X-ray diffraction method indicates that the zinc oxide single phase can be fabricated in this substrate temperature range. The sensitivity of the film synthesized at substrate temperature of 130°C is 2·17 in the presence of CO₂ gas at a measuring temperature of 100°C.     

Synthesis and characterization of sol-gel derived TiO<Subscript>2</Subscript> thin films: Effect of different pretreatment process

Titanium dioxide (TiO₂) thin films have been successfully synthesized deposited on glass substrates by the sol-gel dip-coating method through different pretreating processes, including heated at 100, 500°C, via freeze drying, microwave heating for 10 min and subsequently annealed at 500°C for 2 h. The as-synthesized TiO₂ films were characterized using X-ray diffraction (XRD), atomic force microscopy (AFM) and ultravioletvisible (UV-vis) absorption spectra analysis technology. The preparation of the precursor sols and TiO₂ films were described in detail. Effects of 100, 500°C, freeze drying and microwave heating pretreatment on crystalline structure, surface morphology, roughness, particle size, optical property and electronic transition of TiO₂ thin films have been primarily investigated. The XRD results demonstrate that the TiO₂ films were well-crystallized and consisted of anatase TiO₂ phase only with (101) plane. The average crystalline size is only about 15 nm at 100°C pretreatment and the absorption edge shifts to shorter wavelength comparing with that at 500°C, freeze drying and microwave heating pretreatment. Pretreatment process is important during the preparation of thin films and has obviously effect on the structure and optical property of TiO₂ films due to the different heating mechanisms.     

Facile synthesis and electrochemical properties of layered Li[Ni<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>]O<Subscript>2</Subscript> as cathode materials for lithium-ion batteries

A layered oxide Li[Ni_1/3Mn_1/3Co_1/3]O₂ was synthesized by an oxalate co-precipitation method. The morphology, structural and composition of the as-papered samples synthesized at different calcination temperatures were investigated. The results indicate that calcination temperature of the sample at 850°C can improve the integrity of structural significantly. The effect of calcination temperature varying from 750°C to 950°C on the electrochemical performance of Li[Ni_1/3Mn_1/3Co_1/3]O₂, cathode material of lithiumion batteries, has been investigated. The results show that Li[Ni_1/3Mn_1/3Co_1/3]O₂ calcined at 850°C possesses a higher capacity retention and better rate capability than other samples. The reversible capacity is up to 178.6 mA?h?g^-1, and the discharge capacity still remains 176.3 mA?h?g^-1 after 30 cycles. Moreover, our strategy provides a simple and highly versatile route in fabricating cathode materials for lithium-ion batteries.