Fabrication and characterization of functionally graded nanoclay/glass fiber/epoxy hybrid nanocomposite laminates

In this work, hardness, tensile, impact, bearing strength and water absorption tests were performed to study the mechanical properties of stepwise graded and non-graded hybrid nanocomposites. Three different stepwise graded nanocomposites and one non-graded (homogeneous) nanocomposite with the same geometry and total nanoclay content of 10 wt% were designed and prepared. Moreover, one neat glass fiber laminate was manufactured. The results of the tests indicated that addition of the graded and non-graded nanoclay improves hardness over neat glass fiber reinforcement. The maximum increase in hardness of about 53% over neat specimen is obtained for specimens that have the highest weight percentage (2 wt%) of the clay nanoparticles on its surface (S-specimen and the side of F-specimen that reinforced with 2 wt% nanoclay). The gradation process results in an increase in hardness of about 11% compared with non-graded (homogeneous) specimen. In addition, an improvement of 11.9% in strain-to-failure is achieved with specimen having greatest amount of nanoclay in the middle over neat glass fiber/epoxy composite. The other nanoclay-filled glass fiber composites have strain-to-failure close to neat glass fiber/epoxy. The addition of nanoclay reinforcement has insignificant effect on ultimate tensile strength, tensile modulus, water absorption, bearing strength and impact strength compared with neat glass fiber/epoxy.     

Investigation of the high velocity impact behavior of nanocomposites

In this article, the ballistic behavior of the glass/epoxy/nanoclay hybrid nanocomposites is studied. The fiber glass used is a plain weave 200 g/m², while the nanoclay is an organically modified montmorillonite nanoclay (Closite 30B). The epoxy resin system is made of Epon 828 as the epoxy prepolymer and Jeffamine D‐400 as the curing agent. 0, 3, 5, 7, and 10 wt% of nanoclay particles are dispersed in the epoxy resin. Ballistic tests are performed using flat‐ended projectiles in impact velocities 134 m/s and 169 m/s. The results show that the energy absorption capability and mechanical properties of the composite can be significantly enhanced by adding nanoparticles. When the impact velocity is 134 m/s, near than the ballistic limit, the most increase in the energy absorption capability is observed in 3 wt% nanoclay while with the impact velocity 169 m/s, beyond the ballistic limit, the highest increase is observed in 10 wt% nanoclay. POLYM. COMPOS., 37:1173–1179, 2016. © 2014 Society of Plastics Engineers     

Effect of nanoclay on physical,mechanical, and microbial degradation of jute‐reinforced,soy milk‐based nano‐biocomposites

Jute‐reinforced, soy milk‐based nano‐biocomposites were fabricated using both natural and organically modified nanoclay to study their effect on physical, mechanical, and degradation properties. Different weight percentages of nanoclays were used to modify soy milk by solution casting process. The jute fibers were then impregnated in modified soy resin and compressed to fabricate nano‐biocomposites. About 5 wt% of organically modified nanoclay‐loaded jute composite showed maximum tensile and flexural strength. X‐ray diffraction and transmission electron microscopy (TEM) analysis of fabricated composites confirmed about the formation of nanostructure. Impact, microhardness, dynamic mechanical analysis results of nano‐biocomposites revealed that nanoclay has influenced to improve such physical and mechanical properties. Microbial degradation study of nano‐biocomposites was carried out in cultured fungal bed. Weight loss, tensile loss, and field emission scanning electron microscopy photographs of composites revealed that composites are biodegradable in nature. The prime advantages of these composite are their eco‐compatibility as jute and soy resin, the basic constituents of composites are biodegradable in nature. These composites can be utilized in automobile, packaging, furniture sectors by replacing nondegradable plastic‐based composite. POLYM. ENG. SCI., 54:345–354, 2014. © 2013 Society of Plastics Engineers     

Comprehensive high‐performance epoxy nanocomposites co‐reinforced by organo‐montmorillonite and nano‐SiO2

Comprehensive high‐performance epoxy nanocomposites were successfully prepared by co‐incorporating organo‐montmorillonite (o‐MMT) and nano‐SiO₂ into epoxy matrix. Because of the strong interaction between nanoscale particles, the MMT layers were highly exfoliated, and the exfoliated nanoscale MMT monoplatelets took an interlacing arrangement with the nano‐SiO₂ particles in the epoxy matrix, as evidenced by X‐ray diffraction measurement and transmission electron microscopy inspection. Mechanical tests and thermal analyses showed that the resulting epoxy/o‐MMT/nano‐SiO₂ nanocomposites improved substantially over pure epoxy and epoxy/o‐MMT nanocomposites in tensile modulus, tensile strength, flexural modulus, flexural strength, notch impact strength, glass transition temperature, and thermal decomposition temperature. This study suggests that co‐incorporating two properly selected nanoscale particles into polymer is one pathway to success in preparing comprehensive high‐performance polymer nanocomposites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Improvement of Tensile and Flexural Properties in Epoxy/Clay Nanocomposites Reinforced with Weave Glass Fiber Reel

The tensile strength, tensile modulus, flexural strength and flexural modulus properties were investigated on epoxy/clay nanocomposites to assess the influence of nanoclay. Mechanical properties were significantly increased due to an increase in clay content up to 5 wt%, and decreased with a further increase in clay content. Optimal improvement of properties was observed with increased clay content up to 5 wt%. Duo properties of the glass fiber were improved by clay addition due to the improved interface between the glass fiber and epoxy. SEM analysis was conducted on different fractured surfaces to study the mechanical behavior.     

周期性孪晶结构碳化硅纳米线改性环氧树脂的性能

通过超声分散和模具浇注成型法制备了周期性孪晶结构碳化硅(SiC)纳米线改性环氧树脂,探讨了SiC纳米线的周期性孪晶结构及含量对环氧树脂复合材料力学性能的影响。结果表明,周期性孪晶结构SiC纳米线的加入明显改善了环氧树脂基体的力学性能,孪晶结构有助于提高SiC纳米线与基体树脂之间的相互结合程度。随着孪晶SiC纳米线含量的增加,复合材料的拉伸性能和弯曲性能都呈现出先增加后减小的趋势。当SiC纳米线的含量为2%时,复合材料的拉伸强度、拉伸弹性模量、断裂伸长率、弯曲强度和弯曲弹性模量均达到最大值,相比于纯环氧树脂分别提高了90.6%,37.8%,38.3%,53.4%和24.5%。当SiC纳米线含量为3%时,弯曲应变达到最大值(6.72%),相比于环氧树脂提高了32.0%。     

Effect of nanoclay particles on mold‐filling performance in composites made via resin infusion process

This study investigates the effect of 3 and 5 wt% nanoclay (Cloisite 30B) addition on mold filling time and performance of continuous glass filament mat reinforced unsaturated polyester (UP) resin composites made by vacuum infusion process. X‐ray diffraction and transmission electron microscopy analysis as well as viscosity change in liquid state resin confirmed intercalation and exfoliation of the nanoclay in the resin system. The result shows mold filling time increase of 3 and 2.4 times for the samples containing 3 and 5 wt% nanoclay, respectively, compared with nanoclay‐free sample. This increase in mold filling time is directly attributed to the increase in resin viscosity. Filtration of nanoclay particles were observed in the resin flow direction. Result showed 8 and 14% filtration of nanoclay in flow direction for the samples with 3 and 5 wt% nanoclay content, respectively. Nanoclay containing specimens prepared from near resin entry port area showed relatively higher flexural and tensile modulus and as well as strength compared to specimens prepared from area close to vacuum port area. The result showed best performance for 3 wt% nanoclay containing specimen. However, impact strength decreased about 6.1 and 10.8% for 3 and 5% nanoclay, respectively. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

稻壳二氧化硅/环氧树脂纳米复合材料机械性能研究

将稻壳用10%的盐酸处理后在600℃焚烧得到纯度为99.3%的SiO_2,将SiO_2用偶联剂γ-氨丙基三乙氧基硅烷(KH550)改性后与环氧树脂(EP)复合,探讨了SiO_2质量分数在0～5%范围内复合材料的力学性能.研究结果显示:经硅烷偶联剂KH550改性后稻壳SiO_2粒子为无定形态,尺寸在30～50 nm且能显著提高环氧树脂的力学性能.当稻壳SiO_2质量分数为3%时,材料的拉伸性能以及弯曲性能的提高率最大,拉伸强度、拉伸模量、弯曲模量和弯曲强度的提高率分别为27.25%、6.54%、61.7%和24.56%.SEM研究结果显示:复合材料中SiO_2与基体树脂之间有较好的相容性.     

Improved mechanical and thermal properties of bamboo–epoxy nanocomposites

Natural fiber‐reinforced hybrid composites based on bamboo/epoxy/nanoclay were prepared. Ultrasound sonication was used for the dispersion of nanoclay in the bamboo–epoxy composites. The morphology of bamboo–epoxy nanocomposites was investigated by using scanning electron microscopy, transmission electron microscopy, and X‐ray diffraction. The results show that there exists an optimum limit in which the mechanical properties of composites improved by continuously increasing the nanoclay content. The tensile and flexural strength of bamboo–epoxy nanocomposites with 3 wt% nanoclay increased by 40% and 27%, respectively, as compared to pure composites. The highest value of impact strength was obtained for 1 wt% nanoclay content bamboo–epoxy nanocomposites. The enhanced impact strength of bamboo–epoxy nanocomposites was one of the key advantages brought by nanofiller. The results show that incorporation of nanoclay substantially increases the water resistance capability and thermal stability of bamboo–epoxy nanocomposites. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Mechanical and thermal properties of polypropylene nanocomposites using organically modified Indian bentonite

We report preparation and characterization of nanoclay from Indian bentonite and imported nanoclays, and their compounding with polypropylene (PP) and maleic anhydride‐grafted PP (MA‐g‐PP) in twin screw extruder. The compounded polymer/nanoclay nanocomposites (PNCs) are molded into a standard specimen for studying its tensile, flexural and impact strength. A wide angle X‐ray diffraction (WAXD) and transmission electron microscopy (TEM) study demonstrates intercalation of PP in nanoclays rather than exfoliation for both, indigenous and imported nanoclays. The tensile modulus increased by 41 and 39% for PNC1 (PNC with imported nanoclay) and PNC2 (PNC with indigenous nanoclay) with respect to PP. The flexural modulus for PNC1 and PNC2 also increases by 23 and 22% due to incorporation of 5% nanoclay in PP along with 5% MA‐g‐PP. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Incorporation of silicon dioxide nanoparticles at the carbon fiber‐epoxy matrix interphase and its effect on composite mechanical properties

Functionalized silicon dioxide nanoparticles (nano‐fSiO₂) were uniformly deposited on the surface of carbon fibers (CFs) using a coating process which consisted of immersing the fibers directly in a suspension of nano‐fSiO₂ particles and epoxy monomers in 1‐methyl‐2‐pyrrolidinone (NMP). The 0° flexural properties, 90° flexural properties, and Interlaminar shear strength (ILSS) mechanical properties of unidirectional epoxy composites made with nano‐fSiO₂+epoxy sized carbon fibers, with control fibers, and with epoxy‐only sized fibers were measured and compared. An obvious increase of the fiber/matrix adherence strength was obtained with the nano‐fSiO₂+epoxy coating. The nano‐fSiO₂+epoxy sized CF/epoxy composites showed a relative increase of 15%, 50%, and 22% in comparison to control fibers, for the Interlaminar shear strength, the 90^° flexural strength and the 90° flexural modulus, respectively, but little e difference was measured between the different systems for the 0° flexural properties. The observation of the fracture surfaces by scanning electron microscopy of composite fracture confirmed the improvement of the interfacially dependent mechanical properties. POLYM. COMPOS., 38:1474–1482, 2017. © 2015 Society of Plastics Engineers     

Hydroxyl terminated poly(ether ether ketone) with pendant methyl group‐toughened epoxy clay ternary nanocomposites: Preparation,morphology, and thermomechanical properties

Hydroxyl terminated poly(ether ether ketone) oligomer with pendant methyl group (PEEKMOH) was prepared. Ternary nanocomposites were processed by blending PEEKMOH oligomer with diglycidyl ether of bisphenol‐A (DGEBA) epoxy resin along with organically modified montmorillonite (Cloisite 25A) followed by curing with 4,4'‐diamino diphenyl sulfone. Tensile moduli and flexural moduli were increased, while the tensile strength and Izod impact strength were decreased with increase in clay content. Similarly, storage moduli and loss moduli were increased and glass transition temperature was decreased as the percentage of clay increased. X‐ray diffractograms showed exfoliated morphology even with higher concentration of clay content (8 phr). Scanning electron microscopy of fractured surfaces and tensile failed specimens revealed slow crack propagation and increase in river markings with nanoclay incorporation confirming the improvement in toughness. The domain size of PEEKMOH was decreased with the incorporation of nanoclay into the epoxy matrix, indicating the restriction of growth mechanism by nucleation during phase separation. With increase in clay content, phase separation disappeared indicating gelation occurs before phase separation. Fracture toughness was increased with the addition of PEEKMOH and clay in epoxy resin. Coefficient of thermal expansion of nanocomposites decreases up to 3 phr clay concentrations thereafter it increases. A marginal increase in thermal stability was observed with increase in clay content. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Compression behavior of woven glass/epoxy specimens using a new end‐loaded hybrid specimen

A new compression specimen was applied to woven glass/epoxy laminates. The specimen consists of epoxy layers cast on the sides of the laminate to prevent buckling. Thin‐sheet aluminum ends enable alignment and avoid crushing under end loading, which does not require any special fixture. The compression stress–strain behavior of the laminate was obtained from the specimens by discounting the previously measured stress–strain curve of the epoxy backings. Despite the higher scatter in compression tests, the average modulus was practically identical to the tensile modulus. Moreover, failure occurred away from the ends in nearly all of the specimens tested. The average compressive strength was 84% of the tensile strength and consistent with the flexural strength measured in four‐point bending tests. The present compression specimen could, therefore, become an interesting alternative to the more elaborate standard test methods available. Nevertheless, this new compression testing approach needs further evaluation involving application to other materials. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Bamboo fiber reinforced thermosetting resin composites: Effect of graft copolymerization of fiber with methacrylamide

Epoxy and polyester resins have been reinforced with methacrylamide (MAA) treated bamboo strip matting to develop bamboo fiber reinforced plastic composites. Bamboo mats were graft copolymerized with 1, 3, and 5% solution of MAA. The mechanical (tensile strength, elastic modulus, flexural strength, and flexural modulus), thermal, and water absorption properties of the composites were determined. One percent treatment of bamboo with MAA gave optimum results with epoxy resin. The mechanical properties were improved. TGA results reveal that the degradation temperature of the composite has improved after grafting. The weight loss of 1% MAA treated bamboo–epoxy composite reached a value of 95.132% at 795°C compared to 97.655% at 685°C of untreated bamboo–epoxy composite. Water absorption in the composites was studied by long term immersion and 2 h boiling in distilled water. The process of water absorption indicates Fickian mode of diffusion. MAA treatment results in reduced water uptake. There was improvement in the properties of pretreated bamboo‐polyester matrix composite as well. Three percent treatment of bamboo with MAA gave optimum results with polyester resin. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Increased flexural modulus and strength in SWNT/epoxy composites by a new fabrication method

A new method for preparing SWNT/epoxy nanocomposites has been developed which involves high shear mixing of the epoxy resin and SWNT and heat treating the mixture prior to introducing the hardener. The glass transition temperature of the epoxy resin is unaffected by the presence of nanotubes. An improvement of 17% in flexural modulus and 10% in flexural strength has been achieved at 0.05 wt% of nanotubes. These improvements in flexural modulus and strength are attributed to good dispersion of the nanotubes and grafting of epoxy resin to SWNT by an esterification reaction.     

Mechanical Properties of Bismaleimides Modified Polysulfone Epoxy Matrices

Epoxy resin has been chemically modified using 4, 8, and 12% of bisphenol-A based polysulphone along with three types of bismaleimides, namely [N, N′-bismaleimido-4,4′-diphenylmethane (BMI-1), 1,3-bis (maleimido) benzene (BMI-2) and 1,1′-bis (4-maleimidophenyl) cyclohexane (BMI-3)]. The epoxy hybrid matrices developed, in the form of castings, were used to characterize their mechanical properties like tensile strength, tensile modulus, flexural strength, flexural modulus, impact strength, hardness, and dynamic mechanical analysis as per ASTM standards. Data obtained from mechanical studies indicate that the introduction of hydroxyl terminated polysulfone into epoxy resin enhanced the value of impact strength to the extent of 48% due to the formation of flexible graft structures. Similarly, the incorporation of bismaleimides into epoxy resin also improved both tensile and flexural behavior of epoxy resin. Further, the introduction of combination of both polysulfone and bismaleimides into epoxy resin improved the mechanical properties according to their percentage content. Among the bismaleimides-modified polysulfone epoxy matrices, the epoxy matrix modified with 8% polysulfone and 8% BMI-2 exhibited better mechanical properties than other modified epoxy matrices.     

Synthesis and characterization of chlorinated soy oil based epoxy resin/glass fiber composites

Composites with good toughness properties were prepared from chemically modified soy epoxy resin and glass fiber without additional petroleum based toughening agent. Chlorinated soy epoxy (CSE) resin was prepared from soybean oil. The CSE was characterised by spectral, and titration method. The prepared CSE was blended with commercial epoxy resin in different ratios and cured at 85°C for 3 h, and post cured at 225°C for 2 h using m‐phenylene diamine (MPDA) as curing agent. The cure temperatures of epoxy/CSE/MPDA with different compositions were found to be in the range of (151.2–187.5°C). The composite laminates were fabricated using epoxy /CSE/MPDA‐glass fiber at different compositions. The mechanical properties such as tensile strength (248–299 MPa), tensile modulus (2.4–3.4 GPa), flexural strength (346–379 MPa), flexural modulus (6.3–7.8 GPa) and impact strength (29.7–34.2) were determined. The impact strength increased with the increase in the CSE content. The interlaminor fracture toughness (G_IC) values also increased from 0.6953 KJ/m² for neat epoxy resin to 0.9514 KJ/m² for 15%CSE epoxy‐modified system. Thermogravimetric studies reveal that the thermal stability of the neat epoxy resin was decreased by incorporation of CSE. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Synthesis and mechanical properties of unsaturated polyester based nanocomposites

Two classes of nanocomposites were synthesized using an unsaturated polyester resin as the matrix and sodium montmorillonite as well as an organically modified montmorillonite as the reinforcing agents. X‐ray diffraction pattern of the composites showed that the interlayer spacing of the modified montmorillonite expanded from 1.25 nm to 4.5 nm, indicating intercalation. Glass transition values of these composites increased from 72°C, in the unfilled unsaturated polyester, to 86°C in the composite with 10% organically modified montmorillonite. From Scanning Electron Microscopy, it is seen that the degree of intercalation/exfoliation of the modified montmorillonite is higher than in the unmodified one. The mechanical properties also supported these findings, since in general, the tensile modulus, tensile strength, flexural modulus, flexural strength and impact strength of the composites with modified montmorillonite were higher than the corresponding properties of the composites with unmodified montmorillonite. The tensile modulus, tensile strength, flexural modulus and flexural strength values showed a maximum, whereas the impact strength exhibited a minimum at approximately 3–5 wt% modified montmorillonite content. These results imply that the level of exfoliation may also exhibit a maximum with respect to the modified montmorillonite content. The level of improvement in the mechanical properties was substantial. Adding only 3 wt% organically modified clay improved the flexural modulus of unsaturated polyester by 35%. The tensile modulus of unsaturated polyester was also improved by 17% at 5 wt% of organically modified clay loading.     

Effects of high nano‐SiO2 contents on properties of epoxy‐modified polybenzoxazine

High‐performance nanosilica composites based on epoxy‐modified polybenzoxazine matrices are developed. Chemorheological study of benzoxazine–epoxy resin mixtures reveals that processing window of the benzoxazine resin (BA‐a) is substantially broadened with an addition of the liquid epoxy. Glass transition temperature (T _g) of the BA‐a copolymerized with epoxy resin shows a synergistic behavior with a maximum T _g value (174°C) at the benzoxazine–epoxy mass ratio of 80:20. The copolymer at this composition is also used as a matrix for nano‐SiO₂ composites. A very low melt viscosity of the benzoxazine–epoxy mixtures promotes good processability with the maximum attainable nano‐SiO₂ loading up to 35 wt%. From scanning electron microscopy investigation, fracture surface of the 35 wt% nano‐SiO₂‐filled benzoxazine–epoxy composite reveals relatively homogeneous distribution of the nano‐SiO₂ in the copolymer with good particle wet‐out. In addition, very high reinforcing effect was also observed in such high content of the nano‐SiO₂, i.e., about 2.5 times in modulus improvement. This improvement is attributed to the strong bonding between the copolymer matrix and the nano‐SiO₂ through ether linkage as confirmed by Fourier‐transform infrared investigation. POLYM. COMPOS., 38:2261–2271, 2017. © 2015 Society of Plastics Engineers     

碳纤维湿法缠绕用环氧树脂基体研究

以TDE-85树脂和AFG-90树脂为主体树脂,混合芳香胺为固化剂,研究了一种适合于碳纤维复合材料湿法缠绕成型的树脂配方。结果表明,该树脂的黏度低(＜550 mPa·s)、适用期长,其浇铸体具有优异的力学性能,其拉伸强度为107 MPa,拉伸模量为4．09 GPa,弯曲强度为161 MPa,弯曲模量为3．88 GPa,断裂伸长率超过6%。用其制备的T-700碳纤维缠绕复合材料界面粘接好,NOL环层间剪切强度达到66．8 MPa,拉伸强度达到2．44 GPa。