Preparation of thermoplastic elastomer nanocomposites based on polyamide‐6/polyepichlorohydrin‐co‐ethylene oxide

This work is aimed at determining the effect of nanoclay and polyepichlorohydrin‐co‐ethylene oxide (ECO) content on the microstructure and mechanical properties of PA6/ECO thermoplastic elastomers (TPEs). TPE nanocomposites were prepared in a laboratory mixer using polyamide 6 (PA6), ECO, and an organoclay by a two‐step melt mixing process. First, the PA6 was melt blended with Cloisite 30B and then mixed by ECO rubber. X‐ray diffraction results and transmission electron microscopy image showed that the nanoclay platelets were nearly exfoliated in both the phases. The SEM photomicrograph of PA6 with ECO showed that the elastomer particles are dispersed throughout the polyamide matrix and the size of rubber particles is less than 3 μm. Introduction of organoclay in the PA6 matrix increased the size of dispersed rubber particles in comparison with the unfilled but otherwise similar blends. The nanoscale dimension of the dispersed clay results in an improvement of the tensile modulus of the nanocomposites. POLYM. ENG. SCI., 2011. © 2010 Society of Plastics Engineers     

Effect of clay modification on the morphological,mechanical, and thermal properties of polyamide 6/polypropylene/montmorillonite nanocomposites

Polyamide 6/polypropylene (PA6/PP = 70/30 parts) blends containing 4 phr (parts per hundred resin) of organophilic montmorillonite (OMMT) were prepared by melt compounding. The sodium montmorillonite (Na‐MMT) was modified using three different types of alkyl ammonium salts, namely dodecylamine, 12‐aminolauric acid, and stearylamine. The effect of clay modification on the morphological and mechanical properties of PA6/PP nanocomposites was investigated using x‐ray diffraction (XRD), transmission electron microscopy (TEM), tensile, flexural, and impact tests. The thermal properties of PA6/PP nanocomposites were characterized using thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), and heat distortion temperature (HDT). XRD and TEM results indicated the formation of exfoliated structure for the PA6/PP nanocomposites prepared using stearylamine modified montmorillonite. On the other hand, a mixture of intercalated and exfoliated structures was found for the PA6/PP nanocomposites prepared using 12‐aminolauric acid and dodecylamine modified montmorillonite. Incorporation of OMMT increased the stiffness but decreased the ductility and toughness of PA6/PP blend. The PA6/PP nanocomposite containing stearylamine modified montmorillonite showed the highest tensile, flexural, and thermal properties among all nanocomposites. This could be attributed to better exfoliated structure in the PA6/PP nanocomposite containing stearylamine modified montmorillonite. The storage modulus and HDT of PA6/PP blend were increased significantly with the incorporation of both Na‐MMT and OMMT. The highest value in both storage modulus and HDT was found in the PA6/PP nanocomposite containing stearylamine modified montmorillonite due to its better exfoliated structure. POLYM. COMPOS., 31:1156–1167, 2010. © 2009 Society of Plastics Engineers     

Design and properties of a series of high‐temperature thermoplastic elastomeric blends from polyamides and functionalized rubbers

A series of high‐temperature thermoplastic elastomers (TPEs) and thermoplastic vulcanisates (TPVs) were successfully developed based on two different types of heat resistant polyamide (PA) (25 parts by weight)—PA‐12 and PA‐6, in combination with three different functionalized rubbers (75 parts by weight) of varying polarity, e.g., maleic anhydride grafted ethylene propylene diene terpolymer (MA‐g‐EPDM), sulphonated ethylene propylene diene terpolymer, and carboxylated acrylonitrile butadiene rubber, by melt mixing method. These rubbers have low level of unsaturation in its backbone, and the plastics showed high melting range. Thus, the developed TPEs and TPVs were expected to be high temperature resistant. Resol type resin was used for dynamic vulcanization to further increase the high temperature properties of these blends. Interestingly, initial degradation temperature of the prepared blends was much higher (421 °C for MA‐g‐EPDM/PA‐12) than the other reported conventional TPEs and TPVs. Fourier transform infrared analysis described the interactive nature of the TPEs and TPVs, which is responsible for their superior properties. The maximum tensile strength with lowest tension set was observed for the carboxylated acrylonitrile butadiene rubber/PA‐12 TPV. Mild increase in mechanical properties without any degradation was observed after recycling. Dynamic mechanical analysis results showed two distinct glass transition temperatures and indicated the biphasic morphology of the blends, as evident from the scanning electron microscopy. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45353.     

Fluoroelastomer‐MWNT nanocomposites‐1: Dispersion,morphology, physico‐mechanical,and thermal properties

The present article reports the preparation and characterization of fluoroelastomer/multi‐walled nanotube hybrid nanocomposites prepared by conventional rubber mixing using a two‐roll mill. The morphology of the resulting hybrid nanocomposites were characterized by X‐ray diffraction (XRD), scanning (SEM) and transmission electron microscopies (TEM). SEM photographs showed the formation of completely exfoliated and uniformly dispersed nanotubes in the polymer matrix during the high shear mixing process. Magnetic force microscopy (MFM) has been used to further study the topography of the composites which also showed complete exfoliation. The effect of increasing MWNT loadings on the mechanical properties like tensile strength, modulus, elongation at break, hardness, and tear resistance has also been studied. The fracture surface of the composite has been studied by SEM. A “cross hatched pattern” has been observed. The thermal stability of the composites has been studied by TGA and increase in decomposition temperature with increase in MWNT loadings has been observed which was attributed to the antioxidant nature of nanotubes. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers.     

Microcompounding of organoclay–ABS/PA6 blend‐based nanocomposites

In this study, acrylonitrile–butadiene–styrene (ABS) and polyamide‐6 (PA6) were blended in the presence of an olefin‐based compatibilizer and organoclays. The effects of ABS to PA6 ratio, clay content, and screw speed of the microcompounder were examined by performing morphological (i.e., XRD, SEM, and TEM) and tensile tests. The average aspect ratio of the clay platelets after processing was obtained by applying semiautomatic image analysis method. SEM analysis showed that addition of the compatibilizers to the ABS/PA6 blend system resulted in a decrease in diameter of dispersed phase when one of the phases was continuous. The addition of 5 wt% compatibilizer altered the dispersed morphology to cocontinuous morphology when the weight percentage of ABS was equal to that of PA6. The results of XRD analysis implied that clays were exfoliated in the presence of PA6. It was observed in TEM micrographs that clays were selectively dispersed in PA6 phase. Aspect ratio of the platelets increased as the PA6 content increased. Moduli of the nanocomposites were improved by enriching blend with PA6 and increasing screw speed. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Compatibilizing effect of maleated polypropylene on the mechanical properties and morphology of injection molded polyamide 6/polypropylene/organoclay nanocomposites

Polyamide 6/polypropylene (PA6/PP=70/30 parts) blends containing 4 phr (parts per hundred resin) of organophilic modified montmorillonite (organoclay) were prepared using twin screw extruder followed by injection molding. Maleated polypropylene (MAH-g-PP) was used to compatibilize the blend system. The mechanical properties of PA6/PP nanocomposites were studied through tensile and flexural tests. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to assess the fracture surface morphology and the dispersion of the organoclay, respectively. X-ray diffraction (XRD) was used to characterize the formation of nanocomposites. The thermal properties were characterized by using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The dynamic mechanical properties of PA6/PP nanocomposites were analyzed by using dynamic mechanical thermal analyzer (DMTA). The strength and stiffness of PA6/PP nanocomposites were improved significantly in the presence of MAH-g-PP. This has been attributed to the synergistic effect of organoclay and MAH-g-PP. The MAH-g-PP compatibilized PA6/PP nanocomposites showed a homogeneous morphology supporting the compatibility improvement between PA6, PP and organoclay. TEM and XRD results revealed the formation of nanocomposites as the organoclay was intercalated and exfoliated. A possible chemical interaction between PA6, PP, organophilic modified montmorillonite and MAH-g-PP was proposed based on the experimental work.     

Morphology,thermal and mechanical behavior of polypropylene nanocomposites toughened with poly(ethylene‐co‐octene)

Rubber‐toughened polypropylene (PP) nanocomposites containing organophilic layered silicates were prepared by means of melt extrusion at 230 °C using a co‐rotating twin‐screw extruder in order to examine the influence of the organoclay and the addition of PP grafted with maleic anhydride (PPgMAH) as a compatibilizer on the morphological, mechanical and thermal properties. The mechanical properties of rubber‐toughened polypropylene nanocomposites (RTPPNCs) were studied through tensile, flexural and impact tests. Scanning electron microscopy (SEM) was used for investigation of the phase morphology and rubber particles size. X‐ray diffraction (XRD) was employed to characterize the formation of nanocomposites. The thermal properties were investigated by using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The dynamic mechanical properties were examined by using dynamic mechanical analysis (DMA). From the tensile and flexural tests, the optimum loading of organoclay in RTPP was found to be 6 wt%. The optimum loading of PPgMAH, based on the tensile and flexural properties, was also 6 wt%. The increase in the organoclay and PPgMAH content resulted in a severe embrittlement, manifested by a drop in the impact strength and tensile elongation at break. XRD studies revealed that intercalated RTPPNCs had been successfully prepared where the macromolecular PP segments were intercalated into the interlayer space of the organoclay. In addition, the organoclay was dispersed more evenly in the RTPPNC as the PPgMAH content increased. TGA results revealed that the thermal stability of the RTPPNC improved significantly with the addition of a small amount of organoclay. Copyright © 2006 Society of Chemical Industry     

Morphological,mechanical, and thermal features of PMMA nanocomposites containing two‐dimensional Co–Al layered double hydroxide

The focus of the current study is to investigate the influence of Co–Al layered double hydroxide (LDH) on the morphological, thermal, and mechanical features of poly(methyl methacrylate) (PMMA)‐based nanocomposites. Sodium dodecyl sulfate modified Co–Al LDH was synthesized by single step coagulation method. The PMMA nanocomposites containing different loadings of nanofiller (1–7 wt %) and polystyrene‐grafted maleic anhydride compatibilizer (5 wt %) were melt intercalated via twin screw extruder and later subjected to injection molding to prepare mechanical testing samples. The different properties of PMMA nanocomposites were studied by using XRD, TEM, FTIR, DSC, TGA, tensile, flexural, impact, and flammability analysis. The result of XRD analysis suggested the exfoliated morphology of the nanocomposite while the TEM demonstrated the intercalated structure at higher loading of LDH. The thermal characterization results revealed that thermal properties were improved by the addition of Co–Al LDH, whereas the flammability test exposed that dripping was minimum at 7 wt % loading. The mechanical properties exhibited that optimum results were obtained at 1 wt % loading of Co–Al LDH. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45774.     

Comparison of morphology and mechanical properties of peroxide‐cured acrylonitrile butadiene rubber/LDH composites prepared from different organically modified LDHs

Rubber compounds based on acrylonitrile butadiene rubber (NBR) containing organically modified layered double hydroxides (LDHs) were prepared using peroxide as a curing agent. The LDHs intercalated by organic compounds including sodium styrene sulfonate (SSS) and sodium dodecylbenzene sulfonate (SDBS) were investigated using thermogravimetric analysis (TGA) and X‐ray diffraction (XRD) while the unmodified LDHs were used as contrast. Experimental results from TGA and XRD showed that both SSS‐ and SDBS‐intercalated LDHs were successfully obtained. The morphology of the LDH composites was characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and XRD. The chemical structure of NBR/LDHs compounds were measured by Fourier transform infrared spectrum. The thermal properties were measured by TGA and differential scanning calorimetry. Other properties such as mechanical and swelling properties were also investigated. The results showed that a chemical bonding between organically modified LDHs and rubber matrix through SSS was built during vulcanization, which leads to improved interfacial strength of the cured compound. A high‐performance acrylonitrile butadiene rubber/SSS‐modified LDH compound, which has two times higher tensile strength than cured pure rubber without significant loss of elongation, was obtained. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Novel one‐step synthesis of acrylonitrile butadiene rubber/bentonite nanocomposites with (3‐Mercaptopropyl)trimethoxysilane as a compatilizer

Acrylonitrile butadiene rubber (NBR)/bentonite (Bt) nanocomposites were synthesized by an one‐step method in NBR latex with (3‐Mercaptopropyl)trimethoxysilane (MPTMS) as a compatilizer. The nanocomposites were compounded with curing additives and then vulcanized. The prepared vulcanizates were characterized by Fourier transform infrared spectroscopy (FTIR) and X‐ray diffraction (XRD). The curing properties and mechanical properties were also investigated. The thermal properties were studied with thermal gravimetric analysis (TGA) and differential scanning calorimetry (DSC). The morphology was investigated by field emission‐scanning electron microscopy (FE‐SEM). By swelling test, the swelling ratio and the crosslinking density were achieved. The hydrolyzation and condensation of MPTMS was identified by FTIR while the intercalated/exfoliated structure of Bt was determined by XRD. It was evident that the mechanical properties of the nanocomposites were significantly improved compared with the neat NBR. The well‐dispersed bentonite particles and effects of MPTMS were supported by the images from FE‐SEM. The results of TGA showed that the fastest weight‐loss temperature (T_max) was elevated by over 10°C for the nanocomposites compared with the neat NBR, indicating an enhanced thermal stability. By swelling test, the swelling ratio was determined, decreased to 139% for the optimized NBR/MPTMS/Bt nanocomposites compared with 210% for neat NBR. POLYM. COMPOS., 36:1693–1702, 2015. © 2014 Society of Plastics Engineers     

Rheological and mechanical characteristics of low density polyethylene/ethylene‐vinyl acetate/organoclay nanocomposites

Attempts were made to trace the effect of organoclay (OC) on the rheological and mechanical behaviors of the low density polyethylene (LDPE)/ethylene‐vinyl acetate (EVA) blends. To do this effectively, in addition to LDPE/EVA/OC system, pure LDPE and LDPE/EVA blends were also examined as model systems. The rheological behavior was determined by the capillary rheometer. Morphological characterization was also carried out using X‐ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and theoretical approach based on interfacial energies. Shear viscosity, tensile strength and elastic modulus of LDPE/EVA were found to decrease by increasing the EVA content, while for LDPE/EVA/OC ternary nanocomposites, such properties showed an increase by increasing the content of EVA. Such behavior was explained by the morphological characteristic of the system in which OC was mainly intercalated/exfoliated in the EVA phase. This morphological characteristic was corroborated by the XRD, TEM and interfacial energies data. POLYM. ENG. SCI., 2010. © 2010 Society of Plastics Engineers     

Study on the microstructure and properties of bromobutyl rubber (BIIR)/polyamide‐12 (PA12) thermoplastic vulcanizates (TPVs)

In this study, polyamide‐12 (PA12)/brominated isobutylene‐isoprene (BIIR) TPVs with good mechanical properties and low gas permeability were prepared by dynamic vulcanization in a twin‐screw extruder. The effects of three kinds of compatibilizers on the microstructure and properties of BIIR/PA12 TPV were studied. The compatibility between BIIR and PA12 was improved when maleated hydrocarbon polymeric compatibilizer is added. The reaction between maleic anhydride and amine in polyamide leads to the in situ formation of hydrocarbon polymer grafted polyamide which subsequently can be used to lower the interfacial tension between BIIR and polyamide. The compatibilizing effect of maleic anhydride modified polypropylene (PP‐g‐MAH) on BIIR/PA12 blends is the best among these compatibilizers because the surface energy of PP‐g‐MAH is very close to that of BIIR. The dispersed rubber phase of the blend compatibilized by PP‐g‐MAH shows the smallest size and more uniform size distribution, and the resulting TPVs show the best mechanical properties. The effects of fillers on the properties of BIIR/PA12 TPV were also investigated. The size of the BIIR phase increases with the increase in the content of CaCO₃. The modulus and tensile strength of TPVs increased with the increase in the content of CaCO₃ because of the reinforcing effect of CaCO₃ on TPVs. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43043.     

Synergistic effects of exfoliated LDH with some halogen‐free flame retardants in LDPE/EVA/HFMH/LDH nanocomposites

The synergistic effects of exfoliated layered double hydroxides (LDH) with some halogen‐free flame retardant (HFFR) additives, such as hyperfine magnesium hydroxide (HFMH), microencapsulated red phosphorus (MRP), and expandable graphite (EG), in the low‐density polyethylene/ethylene vinyl acetate copolymer/LDH (LDPE/EVA/LDH) nanocomposites have been studied by X‐ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), thermal analysis (TGA and DTG), mechanical properties, limiting oxygen index (LOI), and UL‐94 tests. The XRD results show that EVA as an excellent compatilizer can promote the exfoliation of LDH and homogeneous dispersion of HFMH in the LDPE/EVA/HFMH/LDH nanocomposites prepared by melt‐intercalation method. The TEM images demonstrate that the exfoliated LDH layers can act as synergistic compatilizer and dispersant to make the HFMH particles dispersed homogeneously in the LDPE matrix. The results from the mechanical, LOI, and UL‐94 tests show that the exfoliated LDH layers can also act as the nano‐enhanced and flame retardant synergistic agents and thus increase the tensile strength, LOI values, and UL‐94 rating of the nanocomposites. The morphological structures of charred residues observed by SEM give the positive evidence that the compact charred layers formed from the LDPE/EVA/HFMH/LDH nanocomposites with the exfoliated LDH layers play an important role in the enhancement of flame retardant and mechanical properties. The TGA and DTG data show that the exfoliated LDH layers as excellent flame retardant synergist of MRP or EG can apparently increase the thermal degradation temperature and the charred residues after burning. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Morphology and thermal/mechanical properties of alkyl‐imidazolium‐treated rectorite/epoxy nanocomposites

A novel organic rectorite (OREC) was prepared by treating the natural sodium‐rectorite (Na‐REC) with ionic liquid 1‐hexadecyl‐3‐methylimidazolium bromide ([C₁₆mim]Br). X‐ray diffraction (XRD) analysis showed that the interlayer spacing of the OREC was expanded from 2.23nm to 3.14nm. Furthermore, two types of OREC/epoxy nanocomposites were prepared by using epoxy resin (EP) as matrix, 2‐ethyl‐4‐methylimidazole (2‐E‐4‐MI) and tung oil anhydride (TOA) as curing agents, respectively. XRD and transmission electron microscope (TEM) analysis showed that the intercalated nanocomposite was obtained with addition of the curing agent 2‐E‐4‐MI, and the exfoliated nanocomposite was obtained with addition of the curing agent TOA when the OREC content was less than 2 wt %. For the exfoliated nanocomposite, the mechanical and thermal property tests indicated that it had the highest improvement when OREC content was 2 wt% in EP. Compared to pure EP, 60.3% improvement in tensile strength, 26.7% improvement in bending strength, 34% improvement in bending modulus, 14°C improvement in thermal decomposition temperature (T_d) and 5.7°C improvement in glass transition temperature (T_g) were achieved. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Preparation and properties of NBR composites filled with a novel black liquor–montmorillonite complex

A novel rubber filler, black liquor–montmorillonite complex (BL–MMT) was prepared by dehydration of a mixture of MMT and BL and used in the preparation of acrylonitrile butadiene rubber (NBR) composites by mechanical mixing method. The BL–MMT/rubber composites were characterized using X‐ray diffraction (XRD), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), and differential scanning calorimeter (DSC). Experimental results of XRD and TEM indicated that MMT was well‐dispersed in the rubber because of the presence of lignin. DSC, thermo‐oxidative aging measurements and TGA results demonstrated that the thermal properties of NBR were improved due to the addition of BL–MMT. The tensile properties including tensile strength, elongation at break, and modulus were also tested. All experimental results indicated that this BL–MMT complex could be an effective reinforcing agent in rubber for cost‐saving and environment benefits. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Morphology,thermal, and mechanical properties of polyamide 66/clay nanocomposites with epoxy‐modified organoclay

A new kind of organophilic clay, cotreated by methyl tallow bis‐2‐hydroxyethyl quaternary ammonium and epoxy resin into sodium montmorillonite (to form a strong interaction with polyamide 66 matrix), was prepared and used in preparing PA66/clay nanocomposites (PA66CN) via melt‐compounding method. Three different types of organic clays, CL30B–E00, CL30B–E12, and CL30B–E23, were used to study the effect of epoxy resin in PA66CN. The morphological, mechanical, and thermal properties have been studied using X‐ray diffraction, transmission electron microscopy (TEM), mechanical, and thermal analysis, respectively. TEM analysis of the nanocomposites shows that most of the silicate layers were exfoliated to individual layers and to some thin stacks containing a few layers. PA66CX–E00 and PA66CX–E12 had nearly exfoliated structures in agreement with the SAXS results, while PA66CX–E23 shows a coexistence of intercalated and exfoliated structures. The storage modulus of PA66 nanocomposites was higher than that of the neat PA66 in the whole range of tested temperature. On the other hand, the magnitude of the loss tangent peak in α‐ or β‐transition region decreased gradually with the increase in the clay loading. Multiple melting behavior in PA66 was also observed. Thermal stability more or less decreased with an increasing inorganic content. Young's modulus and tensile strength were enhanced by introducing organoclay. Among the three types of nanocomposites prepared, PA66CX–E12 showed the highest improvement in properties, while PA66CX–E23 showed properties inferior to that of PA66CX–E00 without epoxy resin. In conclusion, an optimum amount of epoxy resin is required to form the strong interaction with the amide group of PA66. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1711–1722, 2006     

Development of novel polar thermoplastic vulcanizates based on ethylene acrylic elastomer and polyamide 12 with special reference to heat and oil aging

Thermoplastic vulcanizates (TPVs) based on ethylene acrylic elastomer (AEM) and polyamide 12 (PA12) have been developed by the dynamic vulcanization process, in which selective cross‐linking of the elastomer phase (AEM) during melt mixing with the thermoplastic phase (PA12) has been carried out simultaneously. TPVs at varied blend ratios (50 : 50, 60 : 40, 70 : 30) of AEM/PA12 were prepared at 185°C at a rotor speed of 80 rpm up to 5 min of mixing. Di‐(2‐tert‐butyl peroxy isopropyl) benzene (DTBPIB) was chosen as the suitable cross‐linking peroxide to carry out the dynamic vulcanization. Morphology study reveals the development of continuous agglomerate of rubber network in case of all the TPVs took place and the average dimension of the rubber particles are in the range of 30–40 nm. TPV based on 50 : 50 AEM/PA12 shows better physicomechanical properties, thermal stability, and dynamic mechanical behavior among all the TPVs. For aging test, TPVs were exposed to air, ASTM oil 2 and 3. Air aging tests were carried out in hot air oven for 72 h at 125°C, while the oil aging tests were carried out after immersion of the samples into the oils in an aging oven. After aging, there are only slight deterioration of physicomechanical properties of the TPVs. Particularly in case of 50 : 50 blend of AEM/PA12, the retention of the properties even after aging was found excellent. The recyclability of these new TPVs is also found to be excellent leading to find potential application in automotives. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42655.     

Mechanical,morphological, and thermal properties of nanotalc reinforced PA6/SEBS‐g‐MA composites

Ternary butylene‐styrene‐g‐maleic anhydride (SEBS‐g‐MA) (100/20 w/w) blend with varying content of nanotalc (1, 3, and 5 wt %) were prepared by melt compounding followed by injection molding. Thermal properties were investigated by thermogravimetric analysis (TGA) and the results show that the thermal properties of nanocomposites are slightly improved by the addition of nanotalc content. The morphology of nanocomposites using wide angle X‐ray diffraction (WAXD) and transmission electron microscopy (TEM) revealed the delamination of talc layers in the ternary nanocomposites. The dynamic mechanical properties of the samples were analyzed by using dynamic mechanical thermal analyzer (DMTA). The results show that the storage modulus of the blend monotonically increased while tan δ curve show the diffuse pattern with the nanotalc content. The mechanical properties of PA6/SEBS‐g‐MA nanocomposites were studied by tensile, flexural, and impact tests. The tensile and flexural properties continuously increased while izod impact and elongation‐at‐break decreased with nanotalc content. Various theoretical predictive models were used to correlate tensile modulus with the experimental data. The experimental data shows the positive deviation with the applied models. Bela Pukanszky model has been used to calculate the value of parameter B by employing tensile strength data. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41381.     

Synthesis and properties of silicone rubber/organomontmorillonite hybrid nanocomposites

In this article, silicone rubber/organomontmorillonite hybrid nanocomposites were prepared via a melt-intercalation process. The resulting hybrid nanocomposites were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), and thermogravimetric analysis (TGA). The results proved that the organomontmorillonite could be exfoliated into ca. 50-nm thickness and uniformly dispersed in the silicone rubber matrix during the melt-intercalation process. Furthermore, the mechanical properties and thermal stability of the hybrids were very close to those of aerosilica-filled silicone rubber. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1557–1561, 1998     

Synthesis and characterization of cationic gemini surfactant modified Na–bentonite and its applications for rubber nanocomposites

A cationic gemini surfactant (N‐isopropyl‐N , N‐dimethyldodecan 1‐aminium bromide) was synthesized by quaternization reaction. The synthesized surfactant was characterized by Fourier transform infrared (FTIR) and proton nuclear magnetic resonance (1H NMR) spectroscopy. Modified Na–bentonite (organoclay) was obtained by the intercalation of a gemini surfactant between the layers of sodium bentonite and characterized by X‐ray diffraction (XRD), transmission electron microscopy (TEM), FTIR, thermogravimetry–differential thermal analysis (TGA–DTA) and differential scanning calorimetry (DSC) techniques. The results of XRD, TEM, FTIR, TGA, and corresponding DSC analysis indicate that gemini surfactant has been successfully intercalated into the clay layers. Rubber‐based nanocomposites have been prepared by incorporating various concentration of organically modified bentonite on to natural rubber/styrene–butadiene rubber (NR/SBR) rubber blend (75/25) using two roll mill. Effect of organoclay content on XRD, curing, mechanical, and scanning electron microscopy (SEM) properties of the nanocomposites are investigated. The morphological study showed the intercalation of nanoclay in NR/SBR blend chain. It was found that the organoclay decrease the optimum and scorch time of the curing reaction, increase maximum torque and the curing rate, which was attributed to the further intercalation during vulcanization process. Mechanical properties such as tensile strength, modulus and elongation at break have improved. POLYM. COMPOS., 38:396–403, 2017. © 2015 Society of Plastics Engineers